Professional Documents
Culture Documents
KLMABALAY
LOGO Owner :
Location :
3C1
2F - 3F
Check by : Engr. Mark Christian D. Esguerra Date : 11/22/2021
250 mm
εcu = 0.0030 Cover (mm) 40.00
r = As/(b*h) 1.61%
Section Properties: Result:
Width = 400.00 mm Stirrup fy (Mpa) 276.00 Spacing Tie(mm) 120.00
Column Design is Safe
Height = 250.00 mm Stirrup bar(mm) 12.00 Confinement(mm) 75.00
Length = 2,800.00 mm
Applied forces: Shear Design Summary:
Load Case Pu Mx My Shear x Shear y Pu/Puallow Biaxial Shear resistance Spacing Shear resistance Spacing Remark
Remark
D/C D/C Ratio
kN kN/m kN/m kN kN Capacity(kN) Ratio Req. Capacity(kN) Ratio Req.
Case 1 = 309.75 9.71 23.24 17.70 3.41 Pass 0.239 0.326 40.54 0.78 100mm 39.99 0.20 170.00
Case 2 = 300.38 0.17 26.33 17.70 3.41 Pass 0.231 0.236 39.83 0.79 100mm 39.23 0.20 170.00
Case 3 = Pass - -
Case 4 = Pass - -
Case 5 = Pass - -
3D Interaction Diagram Along x Along y
Z-Axis
2,000 2,000
1,500 1,500
1,000 1,000
Y-Axis
500 500
X-Axis
φMn, kNm
φMn, kNm
0 0
-150 -100 -50 0 50 100 150 -200 -150 -100 -50 0 50 100 150 200
-500 -500
Detailed Calculations
Shear Calculation Along X Along Y
Along X c Mn Pn φ φMn φPn c Mn Pn φ φMn φPn
● Minimum Shear Reinforcement NSCP 2015 410.6.2 0 0.0 1997.5 0.65 0.0 1298.4 0 0.0 1997.5 0.65 0.0 1298.4
Vu > 0.5φVc No shear reinforcement Required 410.6.2.1 284 26.1 1997.5 0.65 16.9 1298.4 495 21.0 1997.5 0.65 13.7 1298.4
Shear reinforcement required, 65.63 410.6.2.2 255 47.1 1980.3 0.65 30.6 1287.2 444 43.0 1997.5 0.65 28.0 1298.4
● Shear strength provided by concrete NSCP 2015 422.5.6 226 64.5 1755.0 0.65 41.9 1140.8 394 76.3 1899.6 0.65 49.6 1234.7
Vc (kN)= 115.78 197 76.6 1517.1 0.65 49.8 986.1 344 101.7 1652.8 0.65 66.1 1074.3
● Shear strength provided by transverse reinforcement 169 86.5 1248.1 0.65 56.2 811.3 294 122.0 1376.1 0.65 79.3 894.5
Vs(kN) = 0 140 94.6 926.8 0.65 61.5 602.4 244 136.8 1069.8 0.65 88.9 695.4
● Total Shear Strength 111 101.2 540.9 0.69 69.6 372.2 194 146.9 686.4 0.69 100.9 471.6
Vtotal (kN)= 86.84 82 88.0 293.7 0.85 74.7 249.3 144 135.8 313.1 0.84 114.6 264.3
● Maximum spacing of shear reinforcement (Table 410.7.6.5.2) 54 65.5 -20.3 0.90 58.9 -18.3 93 103.9 -71.6 0.90 93.5 -64.4
Spacing (mm)= 219.00 NSCP 2015 410.7.6.5.2 0 0.0 -765.6 0.90 0.0 -689.1 0 0.0 -765.6 0.90 0.0 -689.1
Along Y Code Requirements Checking for Slenderness
● Minimum Shear Reinforcement NSCP 2015 410.6.2 NSCP 2015 Discription Req. Status Label Along X Along Y
Vu > 0.5φVc No shear reinforcement Required 410.6.2.1 Min Width 250.0 CC
418.7.2.1
Shear reinforcement required, 93.75 410.6.2.2 Ratio 0.4 CC
● Shear strength provided by concrete NSCP 2015 422.5.6 418.7.4.1 Main Bar Ratio 1%-6% CC
Vc (kN)= 108.76 Req. Ties Along X 350.0
CC
● Shear strength provided by transverse reinforcement Actual Ties Along X 200.0
418.7.5.2
Vs(kN) = 0 Ties Along Y 350.0
CC
● Total Shear Strength Actual Ties Along Y 125.0
Vtotal (kN)= 81.57 Req. Spacing inside Lo 62.5
418.7.2.3 NC
● Maximum spacing of shear reinforcement (Table 410.7.6.5.2) Actual Spacing inside Lo 75.0 Legend CC = NSCP 2015 Code Compliant
Spacing (mm) = 144.00 NSCP 2015 410.7.6.5.2 Req. Spacing beyond Lo 96.0 NC = NSCP 2015 Non Code Compliant
418.7.2.5 NC
Actual Spacing beyond Lo 100.0