Professional Documents
Culture Documents
Ref: A&M/SCL/342266/R0
16th July, 2014
Dear Sir,
Based on the same, we are pleased to submit our offer for your kind perusal.
Our detailed offer for THERMOPAC Thermic Fluid Heater Model TPCM - 02 capable of
generating heat output of 2,00,000 KCal/hr, at a temperature of 280°C when fired
with HSD/LDO.
We trust the above is in line with your requirement and incase of any further
clarifications, please feel free to contact us
Thanking you and assuring you of our prompt attention at all times,
Yours faithfully,
For A & M TECHNOLOGIES
(M.RAMA KRISHNA)
9848186200
Encl.:As above
HEATER
One Heat exchanger consisting of two closely wound helical concentric coils
arranged to give three passes on flue gas side made out of ERW tubes
confirming to BS: 3059 Part I suitable for high temperature
One Single jacketed to enclose the heat exchanger coil dully insulated with
mineral wool and coated with color coated sheets
AUXILIARIES
One Dust protected, prewired wall mounted air cooled control panel housing a
Burner Management System, Switch gear consisting of contactors,
Overload relays, fuses/ MCB etc…
One Centrifugal Thermic fluid circulating pump suitable for high temperaure
operation, directly to an electric motor, mounted on a common base frame
One Monobloc Pressure Jet spill return ON/OFF burner suitable for light
oil(HSD) with inbuilt combustion blower assembly along with motor and
high voltage spark ignition for burner light up. The blower will be mounted
with fuel oil pump
FUEL
Oil Line
One spring loaded flow relief valve for mounting on Thermic outlet line.
THERMIC FLUID
One Temperature indicator-cum- switch for burner ON-OFF cycle, on Thermic fluid
inlet of the heater
One Differential pressure switch connected across Thermic fluid inlet and
outlet of the heater for low flow alarm & interlock with burner
One Level switches for low level alarm & interlock with burner, on deaerator-
cum- expansion tank
FLUE GAS
BATTERY LIMITS
FUEL
Oil Line
Inlet/Outlet of burner
THERMIC FLUID
Suction of blower
THERMIC FLUID
Shell Heat Transfer Oil S2 for bulk oil temperature up to 300 Deg C
ELECTRICAL
415 Volts±6%, 50 Hz±3%, 3 phase, 4 wire system and 240 Volts6%, 50 Hz±3%, 1 phase
for control circuit
AMBIENT CONDITIONS
2. Storage, Service tanks for Fuel Oil/Gas, Thermic Fluid etc. and piping
required up to THERMOPAC.
4. All user equipment, their heat exchangers, automatic and manual valves and
temperature controllers etc.
7. CO2 for smothering and CO2 line up to our battery limits (stop valve).
8. Thermic fluid, Fuel oil/gas, water, power, compressed air, Labour, tools
and tackles, consumables etc. required for assembly, erection,
commissioning and operation of THERMOPAC.
9. All electrical wiring such as from Thermic fluid pump motor and from level switch
in deaerator-cum-expansion tank up to control panel, main supply cable to control
panel etc.
1. OPERATING PARAMETERS:
- Model : TPCM - 02
- Fuel : HSD/LDO
3. PRICE BASIS:
The prices mentioned above are ex-works, Pune and shall exclude the
following charges:
NOTE: The above mentioned taxes and levies shall be charged as per the rates
prevailing at the time of delivery.
Statutory Variation
“ Any additional taxes, duties and levies/imposition of new taxes, duties and levies at
the time of execution of this contract (till the time of final invoice) either due to
change in law or due to any interpretations of Tax authorities, shall be extra to
Purchaser’s account and shall be paid to Supplier.”
4. PAYMENT TERMS
5. DELIVERY PERIOD
The equipment shall be ready for delivery at our works in 9 Weeks from the
date of technically and commercially clear order with requisite advance.
6. VALIDITY
The offer is open for acceptance for a period of 30 days from this date.
*** Note: we request you to release your purchase order on M/s. Thermax Limited,
Hyderabad