Professional Documents
Culture Documents
ULTRAFILTRATION MEMBRANE
MEMBRANE ELEMENT DATASHEET
AQUAFLEX HP
ARTICLE CODE : 23E1FL395H
Aquaflex 55 is an ultrafiltration module, used Sodium Hypochlorite As a good working practice and in order to
for production of process and potable water. - Typical 200 ppm, at ≤ 40 ºC at ≥ pH 10 maximise the lifetime of the membrane it is
Typical applications are the filtration of surface - Maximum 500 ppm advised to reduce the membrane exposure
water, potable water and WWTP effluent. Mode - 250.000 ppm hours cumulative; ≥ pH 10 to oxidising agents to a minimum. Exposure
of operation is feed-and-bleed with a minor limits are also affected by temperature,
Chlorine Dioxide
crossflow or dead-end mode with regular pH and the presence of metals. In order
- Typical 1 ppm, at ≤ 40 ºC
backwash (permeate only) and chemically not to exceed maximum exposure limits,
- Maximum 2 ppm
enhanced backwash. membranes must be preserved free of any
- 90.000 ppm hours cumulative; pH 11
oxidising agent when the plant is stopped.
Hydrogen Peroxide
GENERAL SOLVENT RESISTANCE Acids
- Typical 200 ppm, at ≤ 40 ºC
Hydrochloric Acid ++
- Maximum 500 ppm
Nitric Acid ++
Since the resistance of the membrane to - 350.000 ppm hours cumulative
Sulphuric Acid ++
solvents strongly depends on the actual Note: Phosphoric Acid ++
process conditions, the indications given below The above figures for oxidant contact Acetic Acid ++
should only be considered as guideline. represent the membrane resistance to Citric Acid ++
Acids ++ each individual oxidizing agent. The total
pH > 2 during filtration
Bases ++ combined exposure for Sodium Hypochlorite
pH > 1 during cleaning
Organic esters, ketones, and Chlorine Dioxide will be calculated as
ethers - follows: Bases
Aliphatic alcohols + Sodium Hydroxide (<4%) ++
Combined exposure (NaOCl + ClO2) = 2.6 x
Aliphatic hydrocarbons + Potassium Hydroxide (<4%) + +
Exposure to ClO2 (in ppm hours)+ Exposure
Halogenated hydrocarbons -- to NaOCl (in ppm hours) < 250.000 ppm pH < 12 during filtration
Aromatic hydrocarbons -- hours pH < 13 during cleaning
Polar organic solvents --
Oils ++
MEMBRANE CHARACTERISTICS
OPERATING SPECIFICATIONS
Max. Max. trans- Max. • Backwash water should be free of element to sudden temperature changes,
Temp. particulates and should be of UF permeate particularly decreasings. Bring the module
system membrane backflush
range quality or better or element back to ambient operating
pressure pressure pressure
temperature slowly (max. value 3 °C/min).
[kPa/psi] [kPa/psi] [kPa/psi] [°C/°F] • Backwash pumps should preferably be Failure to adhere to this guideline can
made of non-corroding materials, e.g., result in irreparable damage
300 300 300 0-40 plastic or stainless steel. If compressed
[43] [43] [43] [32-104] air is used to pressurize the backwash Operation of membrane modules at any
water, do not allow a two-phase air/water combination of maximum limits of pH,
mixture to enter the element concentration, pressure or temperature,
during cleaning or production, will influence
• To avoid mechanical damage, do not the membrane lifetime.
subject the membrane module or
TECHNICAL SPECIFICATIONS
X-FLOW BV
P.O. BOX 739, 7500 AS ENSCHEDE, NETHERLANDS WWW.X-FLOW.COM
Note: The information and data contained in this document are based on our general experience and are believed to be correct. They are given in good faith and are intended
to provide a guideline for the selection and use of our products. Since the conditions under which our products may be used are beyond our control, this information does not
imply any guarantee of final product performance and we cannot accept any liability with respect to the use of our products. The quality of our products is guaranteed under our
conditions of sale. Existing intellectual property rights must be observed.
DS AQUAFLEX 55 EN 0119 © 2019 Pentair. All Rights Reserved.