Professional Documents
Culture Documents
PRACTICAL PROBLEM
INSTRUCTION: Select the correct answer for each of the following questions. Mark only
one answer for each item by shading the box corresponding on the letter of
your choice on the answer sheet provided. STRICTLY NO ERASURES
ALLOWED. Use pencil No. 2 only.
MULTIPLE CHOICE
1. In a plan, what are these thin and dark lines called that are constructed with units
of one long dash followed by two short dashes and are used to indicate the scope
of movement of a part such as showing the path a door will follow when opened?
a. extension lines b. phantom lines
c. object lines d. leader lines
c. 100
d. 10
11. A lavatory with a pop-up drain assembly connects to the drain using a:
a. 1-1/2” threaded tailpiece
b. 1-1/2” flanged tailpiece
c. 1-1/4” flanged tailpiece
d. none of the above (1-1/4” threaded tailpiece)
12. One important concern when installing an electric water heater is:
a. ensuring that all devices and controls can be readily accessed
b. whether the storage tank is a top fed type
c. ensuring that the gas pipe is sized correctly
d. confirming that the electrician is licensed
14. The type of union that is installed when using copper pipe to connect to a water
heater is a:
a. malleable union
b. dielectric union
c. electric union
d. none of these
15. The label located on the exterior of a water heater indicating specific information
about that water heater is also known as:
a. an information sticker
b. a boiler plate
c. the manufacturer safety data sheet (MSDS)
d. None of the above
16. A gas water heater design in which the heater is installed inside a dwelling along
an exterior wall and utilizes a dual-flue pipe system is called:
a. conventionally vented b. point of use
c. instantaneous d. direct vented
17. When a solar collector (panel) is located away from the storage tank, ___ the
water through the system.
a. a pump is required to circulate
b. air is injected to force
c. both of these
d. None of the above
20. Codes dictate that ___ be installed in the cold water piping near a water heater.
a. pressure booster b. circulating pump
c. an isolation valve d. All of the above
23. What is the temperature rise if the incoming water to a water heater is 50⁰F and
the outgoing water is 120⁰F?
a. 50⁰F b. 70⁰F
c. 100⁰F d. 120⁰F
26. One BTU increases the water temperature of ___ by one degree Fahrenheit
a. one gallon b. one ounce
c. one quart d. one pound
31. The difference between incoming cold water temperature and outgoing hot
water temperatures is known as:
a. the boiling point
b. temperature rise
c. heating cycle
d. minimum and maximum cycle
36. The most common distance between the hot and cold rough-in on a sink is:
a. 4”
b. 6”
c. 8”
d. none of the above
47. Connecting a city water supply system with piping from a private well is:
a. known as a cross-connection and illegal
b. illegal and common for irrigation systems
c. known as a cross-connection
d. illegal
48. Most codes dictates that a fixture cannot be supplied with more than:
a. 80 lbs of pressure
b. 90 lbs of pressure
c. 100 lbs of pressure
d. none of the above
56. Which fitting or fitting combination is best used at the base of a soil or waste
stack?
a. 1/4 bend
b. short sweep, 1/4 bend
c. 2 pcs 1/8 bend
d. wye branch & 1/8 bend
58. Which of the following is considered the most efficient type of venting system?
a. combination waste and vent
b. group vent
c. wet vent
d. individual vent
59. Which of the following material is not recommended for use in water supply
system application?
a. plastic pipe
b. galvanized steel pipe
c. brass pipe
d. concrete pipe
60. The water supply to a water closet utilizing a flush valve is:
a. 3/4" b. 1”
c. 1/2” d. 1-1/4”
b. storm drain
c. cesspool
d. privy
69. A kitchen sink faucet that has a base plate and a separate spray requires a:
a. three-hole sink
b. four-hole sink
c. two-hole sink
d. None of the above
73. The two basic flushing actions options for toilets are:
a. vortex and blowout
b. jet and siphon
c. siphon and vortex
d. siphon jet and blowout
75. Two fixtures that are installed in separate rooms but on the same wall are
considered:
a. back-to-front
b. back-to-back
c. side-by-side
d. front-to-back
76. The rims of bowls used for handicap toilet and nonhandicap toilets:
a. are the same height from the floor
b. are not the same height from the floor
c. connect differently to the drain
d. are installed at different distances from a back wall
79. The only safe method to ignite a torch used for soldering is a: (MP July 2016)
a. lighter b. striker
c. fuel d. match
81. A saw used to productively cut threaded rod is a: (MP July 2016)
a. hacksaw
b. tube saw
c. portable band saw
d. chisel
83. Using a 1/8” scale to interpret a blueprint dimension means that 1/8” equals:
a. one inch
b. one-eighth
c. one yard
d. one foot
PREBOARD MPLE 2017 10
88. The four different types of copper pipe commonly used today are identified as:
a. Red, blue, green and white
b. M, L, K and DWV
c. 1, 2, 3, 4
d. A, B, C, D
94. Excavated soil should not be placed any closer than ___ from the edge of a
trench.
a. 2’-0”
b. 1’-0”
c. 3’-0”
d. 4’-0”
99. The person responsible for monitoring a permit required confined space is called:
a. A first responder
b. A monitor
c. An entrant
d. An Attendant
PRACTICAL PROBLEM
INSTRUCTION: Select the correct answer for each of the following questions. Mark only
one answer for each item by shading the box corresponding on the letter of
your choice on the answer sheet provided. STRICTLY NO ERASURES
ALLOWED. Use pencil No. 2 only.
MULTIPLE CHOICE
1. In a plan, what are these thin and dark lines called that are constructed with units
of one long dash followed by two short dashes and are used to indicate the scope
of movement of a part such as showing the path a door will follow when opened?
a. extension lines b. phantom lines
c. object lines d. leader lines
11. A lavatory with a pop-up drain assembly connects to the drain using a:
a. 1-1/2” threaded tailpiece
b. 1-1/2” flanged tailpiece
c. 1-1/4” flanged tailpiece
d. none of the above (1-1/4” threaded tailpiece)
12. One important concern when installing an electric water heater is:
a. ensuring that all devices and controls can be readily accessed
b. whether the storage tank is a top fed type
c. ensuring that the gas pipe is sized correctly
d. confirming that the electrician is licensed
14. The type of union that is installed when using copper pipe to connect to a water
heater is a:
a. malleable union
b. dielectric union
c. electric union
d. none of these
15. The label located on the exterior of a water heater indicating specific information
about that water heater is also known as:
a. an information sticker
b. a boiler plate
c. the manufacturer safety data sheet (MSDS)
d. None of the above
16. A gas water heater design in which the heater is installed inside a dwelling along
an exterior wall and utilizes a dual-flue pipe system is called:
a. conventionally vented b. point of use
c. instantaneous d. direct vented
17. When a solar collector (panel) is located away from the storage tank, ___ the
water through the system.
a. a pump is required to circulate
b. air is injected to force
c. both of these
d. None of the above
PREBOARD MPLE 2017 23
20. Codes dictate that ___ be installed in the cold water piping near a water heater.
a. pressure booster b. circulating pump
c. an isolation valve d. All of the above
23. What is the temperature rise if the incoming water to a water heater is 50⁰F and
the outgoing water is 120⁰F?
a. 50⁰F b. 70⁰F
c. 100⁰F d. 120⁰F
26. One BTU increases the water temperature of ___ by one degree Fahrenheit
a. one gallon b. one ounce
c. one quart d. one pound
b. 83.3 lbs
c. 8.33 lbs
d. 69.4 lbs
31. The difference between incoming cold water temperature and outgoing hot
water temperatures is known as:
a. the boiling point
b. temperature rise
c. heating cycle
d. minimum and maximum cycle
36. The most common distance between the hot and cold rough-in on a sink is:
a. 4”
b. 6”
c. 8”
d. none of the above
47. Connecting a city water supply system with piping from a private well is:
a. known as a cross-connection and illegal
b. illegal and common for irrigation systems
c. known as a cross-connection
d. illegal
48. Most codes dictates that a fixture cannot be supplied with more than:
a. 80 lbs of pressure
b. 90 lbs of pressure
c. 100 lbs of pressure
d. none of the above
56. Which fitting or fitting combination is best used at the base of a soil or waste
stack?
a. 1/4 bend
b. short sweep, 1/4 bend
c. 2 pcs 1/8 bend
d. wye branch & 1/8 bend
58. Which of the following is considered the most efficient type of venting system?
a. combination waste and vent
b. group vent
c. wet vent
d. individual vent
59. Which of the following material is not recommended for use in water supply
system application?
a. plastic pipe
b. galvanized steel pipe
c. brass pipe
d. concrete pipe
60. The water supply to a water closet utilizing a flush valve is:
a. 3/4" b. 1”
c. 1/2” d. 1-1/4”
69. A kitchen sink faucet that has a base plate and a separate spray requires a:
a. three-hole sink
b. four-hole sink
c. two-hole sink
d. None of the above
73. The two basic flushing actions options for toilets are:
a. vortex and blowout
b. jet and siphon
c. siphon and vortex
d. siphon jet and blowout
PREBOARD MPLE 2017 29
75. Two fixtures that are installed in separate rooms but on the same wall are
considered:
a. back-to-front
b. back-to-back
c. side-by-side
d. front-to-back
76. The rims of bowls used for handicap toilet and nonhandicap toilets:
a. are the same height from the floor
b. are not the same height from the floor
c. connect differently to the drain
d. are installed at different distances from a back wall
79. The only safe method to ignite a torch used for soldering is a: (MP July 2016)
a. lighter b. striker
c. fuel d. match
81. A saw used to productively cut threaded rod is a: (MP July 2016)
a. hacksaw
b. tube saw
c. portable band saw
d. chisel
83. Using a 1/8” scale to interpret a blueprint dimension means that 1/8” equals:
a. one inch
b. one-eighth
c. one yard
PREBOARD MPLE 2017 30
d. one foot
88. The four different types of copper pipe commonly used today are identified as:
a. Red, blue, green and white
b. M, L, K and DWV
c. 1, 2, 3, 4
d. A, B, C, D
d. none of these
94. Excavated soil should not be placed any closer than ___ from the edge of a
trench.
a. 2’-0”
b. 1’-0”
c. 3’-0”
d. 4’-0”
99. The person responsible for monitoring a permit required confined space is called:
a. A first responder
b. A monitor
c. An entrant
d. An Attendant