Professional Documents
Culture Documents
300mm
~ )
II' 11\
E E
E E
0 0
00 l()
v l()
•••• \11
\11
2. The maximum bending moment due to the beam dead load - ~ t' leA) -'(\1\
3. The total force used for initial prestressing -- I ~ 2> :l"~' I{' ~~-C I 't 2,,'\""" >< '1.~
------~ "'"
...•
4. Concrete stress in the top & bottom of the beam at mid span after the tendons
are cut ~ b' t.J"..,.,. ':O;S ~IMY.'l- (t~ )
M~ ~ ::;. \J\&-- N!\M"'f<)'
5. Concrete stress at the top & bottom of the beam at mid s an assuming'
18% losses in tendons <}t ,tJ-.!:> ~nlt~..\""", ~~, 1:,.::),' 4.~ N/""", w ~ (~~)
1,;(-JV-J.rI, k ~ :,:.~':r.,. ''';)-"0 4 ~ lw.. w'V
7. The maximum allowable bending moment at midspan assuming'" . r
an allowable stress of 16 MPa in compression z: 3~3.\ '2;. ~:AJ _ VII) 9
8. The maximum allowable bending moment at midspan assuming
an allowable stress of 3 MPa in tension
.;:;;~~~~~.-_.
Problem 2
Per ACI Code, what are the limits for the permissible extreme fiber stress in tension in
precompressed tensile zone under service load for uncracked, partially cracked and
cracked members.
r "
,.. \ :1
,-.
!..
, .1
500mm 12m
< ) <E(----------------____=;.
)
E
E
!I
.~--_ . _--- ~--P ~
~ -+
o
o
<0
250mm
Moment of Inertia of
gross section =
657650 cm4
(f.-tJ -M')
The 12m simply supported T beam shown above is prestressed with a force of 1400 KN,
using a parabolic tendon with an eccentricity of 75 mm above the concrete centroid at the
supports and 195 mm below the centroid at mid span. After time-dependent losses have
occurred, this prestress is reduced to 1190 KN. In addition to its own weight of 4.8 KN/m,
the girder must carry a short-term Jive load of 13.1 KN/m. Determine the Design Class for
the member and estimate the deflection at all critical stages of loading. The creep
coeffi~ient =
2.0,_modulus of elasticity of concret: 27586 MPa, and mOdUIU~O!~~p~e.. =
A +- C t4
~__ "_.2.~t¥r~'~'·..:-
(cracking stress) - 3.65 MPa.
{j,lAU "':'
(\ I rj'l -
.
"" ~t\?P~··".
r ,"'" \\ 'J
I .---
f) . :~. '" ,if,;'.~ sr
1.I "'" <1), i~ »
11*1 OJ
htJ~o
r: S-"7 S.
u·
/ A: . ,,_.
~':5!- /1
,
("L
hl/\)...\'·
,L
o,l.
/;~r "~::: (6/
"-1, ,'~.I . L ) I
i
I
r JiI".-
.......-
II)
-- "'-':~"~~;~";-,
b~)__
0'1
',,,, .. "J
:;. t : 0 > 2
...."
'~:;'/:I
l./'
""I,
-- ----- - - - -
-----~
~-~ 1
150mm H
o·1.-~ b
I
r-~--'Y-1'J-'--t
240mm
Problem 4
Design End - zone reinforcement for the rectangular post-tensioned beam shown above.
The initial pre-stress force of 1100 KN is applied by two closely spaced tendons having a
combined eceentricity of 200 mm. Material properties are fck (initial) = 36 MPa & fy = 415
MPa
·.. \1 :r
"'1!) -;. \~ I<"'\')~"""
y-o .
f -