Professional Documents
Culture Documents
MINISTRY OF ELECTRICITY
Section 2
Technical Data
2
A) 33kV Metal CladSwitchgear
Specification
No. Description Unit
Required Proposed
Specification
No. Description Unit
Required Proposed
Rated supply voltage of closing and
2.8
opening devices, auxiliary
and control circuits
• Closing and Tripping V DC 48
• Indication V DC 48
• Control V DC 48
3 DESIGN DETAIL
3.1 Busbars
• Type Single
• Rated normal current A 1250
• Temperature rise on
°C To be filled in
continuous operation.
• Cross section area mm2 To be filled in
According
• Insulation of busbar
to clause 3.1.5
• Maximum working temperature of
°C To be filled in
busbar insulation
• Minimum clearance
mm To be filled in
between phases
• Minimum clearance between
mm To be filled in
phases and earth
3.2 Material
• Cover Metallic
• Partitions Metallic
• HV conductor copper
Silver-plated
• Contacts
copper
Minimum thickness of sheet
3.3 mm To be filled in
metal used.
3.4 Color and type of painting for panel. Light gray finish
3.5 Degree of protection
• SF6gas Enclosed IP66
Compartment
4
• Cable IP41
• Instruments IP50
• Bus-bar To be filled in
Busbar/Circuit
3.6 Minimum compartments of Breaker/Cable/
cubicles at switchgear board LV-voltage
compartment
3.7 Pressure relief device Yes
4 DIMENSION AND WEIGHT
4.1 Dimensions (L x W x H)
• Incoming Cubicle m To be filled in
• Transformer Cubicle m To be filled in
4.2 Weight
• Incoming Cubicle kg To be filled in
• Transformer Cubicle kg To be filled in
B CIRCUIT BREAKER
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Interrupter Distinguishing Medium Vacuum, triple
and type of C.B pole operation,
1.4 Model To be filled in
1.5 Applicable Standards IEC62271-100
1.6 Number of poles 3
Inside metal
1.7 Location of service
Enclosed GIS
Switchgear
Motor charged
1.8 Type of operating mechanism
Spring
Type Tests included extended endurance
1.9
test (10000 operation for incomer) (30000
operation for feeders)
8
Technical Particulars and Guarantees of 33 kV Metal Enclosed GIS Switchgear
Specification
No. Description Unit
Required Proposed
2) For Protection
• Accuracy class 5P10
• Rated burden VA Min 15
Technical Particulars and Guarantees of 33 kV Metal Enclosed GIS Switchgear
Specification
No. Description Unit
Required Proposed
E VOLTAGE TRANSFORMERS
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
Molded type
1.3 Type
Indoor
1.4 Model To be filled in
1.5 Applicable Standards IEC60044-2
1.6 Number of phases Single phase x 3
2 ELECTRICAL DATA
2.1 Rated primary voltage kV 33 /√3
10
Technical Particulars and Guarantees of 33 kV Metal Enclosed GIS Switchgear
Specification
No. Description Unit
Required Proposed
B) 33/0.416kV AuxiliaryTransformer
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
Oil immersed
1.3 Type cable box for
both H.V & L.V
1.4 Model To be filled in
1.5 Applicable Standards IEC60076
1.6 Location of service Outdoor
1.7 Short circuit Test Report
Date of carried out To be filled in
Testing laboratory name and country To be filled in
Certificate Provided Yes
2 RATINGS
2.1 Rated power KVA 100
2.2 Rated voltage ratio
33(+2 x 2.5%/-2
• Primary kV
x
2.5%)
• Secondary kV 0.416Y/0.24
2.3 Number of phase 3
2.4 Frequency Hz 50
2.5 Vector group symbol Dyn11
2.6 Cooling method ONAN
Maximum temperature rise at
2.7
rated power
• Top oil bythermometer K 45
• Winding byresistance K 50
Technical Particulars and Guarantees of 100 kVA, 33/0.416kV Auxiliary Transformer
Specification
No. Description Unit
Required Proposed
• Insidetank To be filled in
• Outsidetank To be filled in
glove or valve
4.6 Type of valves
gates
5 DIMENSION AND WEIGHT
Dimension of Transformer
5.1 mm To be filled in
(L x W x H)
12
5.2 Total oil required
• Volume Liter To be filled in
• Weight Ton To be filled in
5.3 Net weight of copper winding and kg To be filled in
Total weight of complete
5.4 kg To be filled in
transformer including fitting and
A BATTERIES
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
Pocket-plate
1.3 Type Hi- discharge
type Nickel-
Cadmium
1.4 Model To be filled in
IEEE 1115 for
Applicable Standards calculation,
1.5
IEC60623
equipment
2 DESIGN DETAIL
Rated capacity for 10 hours rate
2.1 AH
(To be confirmed calculation Report)
2.2 Rated voltage of battery V 48
2.3 Nominal charging rate current A To be filled in
2.4 Nominal voltage of battery cell V/cel 1.2
l
2.5 Number of cells 40
2.6 Final discharge-end voltage V/cel To be filled in
l
Potassium
2.7 Type of electrolyte
hydroxide
2.8 Specific gravity of electrolyte at 20°C To be filled in
Nickel-
2.9 Type of positive plate
hydroxide
and graphite
Electrolytic
2.10 Type of negative plate
cadmium
2.11 Type of separators To be filled in
Technical Particulars and Guarantees of DC48V Battery and Battery Charger
Specification
No. Description Unit
Required Proposed
Steel painted
2.12 Type of mounting rack trays with anti-
acid coating
Anticipated life of electrolyte
2.13 Years To be filled in
under actual operation condition
3 DIMENSION AND WEIGHT
Over all dimension of batteries on
3.1 m To be filled in
rack
3.2 Weight of cell withelectrolyte Kg/cell To be filled in
3.3 Volume of electrolyte Liter/cell To be filled in
B BATTERY CHARGERS
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
Full automatic
1.3 Type of battery charger constant
voltage DC
power
source
Single
1.4 Type of rectifier phase
Thyristor
full wave
bridge
1.5 Type of cooling for rectifier Self air-cooled
1.6 Model To be filled in
1.7 Applicable Standards IEC62040-1, -2, -
3
1.8 Degree of protection IP 41
2 or Dual type
1.9 Number of chargers
2 ELECTRICAL DATA
14
2.1 Rated input AC voltage V 230 ±10%
2.2 Number of phase of AC input 1
2.3 Rated Frequency Hz 50
2.4 Input Power VA To be filled in
Voltmeter for input voltage Yes
with Selector Switch (ON/OFF
)
Regulated voltage range on DC
2.5 V 48 V ±10%
busbar
Means of regulating output voltage Semi-conductor
2.6
on DC busbar dropper
2.7 Di-electric strength (50Hz for 1
minute)
• Between AC phases and earth V 2000
• Between AC and DC circuit V 2000
3 DESIGN DETAIL
Continuous rated output
3.1
current including the derating
• On floatmode A To be filled in
• On boostmode A To be filled in
3.2 Charger rate output voltage
• FloatCharging V To be filled in
• BoostCharging V To be filled in
Manual voltage regulator
3.3
(float/boost charge)
• Voltage settingrange V To be filled in
• Boost charging currentsetting A To be filled in
• Boost charging voltagelimit
V To be filled in
setting range
3.4 Voltageripple % To be filled in
Setting range of DC under-
3.5 To be filled in
voltage relay
3.6 Setting current range for DC earth To be filled in
Air-insulated
3.7 Type of charger Cubicle metal-
enclosed
type
Light-grey
3.8 Color of Cubicle
finish, Semi-
gloss
Technical Particulars and Guarantees of DC48V Battery and Battery Charger
Specification
No. Description Unit
Required Proposed
16
3.6 Rated short time current (3 s) kA To be filled in
3.7 Maximum operating time
• Opening ms To be filled in
• Closing ms To be filled in
3.8 Voltage / power coil rating V/W To be filled in
3.9 Typical circuit diagram number To be filled in
Thermal or
3.10 Protection
Electrical
Specification
No. Description Unit
Required Proposed
18
1.2 Country of Manufacturing To be filled in
1.3 Model To be filled in
1.4 Applicable Standards To be filled in
2 ELECTRICAL DATA
2.1 Rated voltage V DC 48 ±15%
2.2 Maximum power consumption W To be filled in
2.3 Rated frequency Hz 50
3 DESIGN DETAIL
3.1 Main Processor To be filled in
3.2 Processor clock speed GHz To be filled in
3.3 Operating System To be filled in
3.4 Memory size GB To be filled in
3.5 Maximum Memory Capacity GB To be filled in
3.6 Hard Drive TB To be filled in
3.7 Add up to Hard Disk TB To be filled in
3.8 Optical Drive To be filled in
3.9 External Ports To be filled in
3.10 Network
Communication Protocols to DCC IEC 60870-5 101
& 104
Communication Protocols in
IEC 61850
Substation LAN
3.11 TCP/IP Internet Yes
3.12 GPS Interface Yes
3.13 RS232 Interface Yes & ≥ 64kbps
3.14 RS485 Interface Yes & ≥ 64kbps
4 DIMENSION AND WEIGHT
4.1 Dimensions (L x W x H) mm To be filled in
4.2 Weight kg To be filled in
Specification
No. Description Unit
Required Proposed
20
connector
22
Decimal factor(AMI/ASO) 0….IE10
Engineering(AMI/ASO) 32 ASCII
E) Communication equipment
Technical Particulars and Guarantees of communication equipment
(UHF)
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type To be filled in
1.4 Model To be filled in
1.5 Applicable Standards To be filled in
1.6 Configuration Duplicate
1.7 Type Test
Date of carriedout To be filled in
Testing laboratory name and
To be filled in
country
Certificate Provided Yes/No
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC 12 ±15%
2.2 Power consumption W To be filled in
Transmit(Maximum) A To be filled in
Receive(Maximum) A To be filled in
2.3 Rated Frequency Hz 50
2.4 Input Power VA To be filled in
3 DESIGN DETAIL
3.1 Power output W To be filled in
3.2 Frequency setting range: MHz 335.4〜470
Frequency is
Frequency transmit andreceive MHz
decided after
Contract
Communication method
3.3 F2D/F3E ,Simplex/half duplex/full To be filled in
duplex)
3.4 Antenna Impedance Ω To be filled in
3.5 Transmission Rate kbps To be filled in
Modulation method: MSK To be filled in
3.6
(Minimum shift keying)
3.7 Interface RS-232C
Transmission Rate Kbps To be filled in
Communication procedure:
Yes
ASYNCasynchronous
3.8 Telephone call by headset Yes
4 DIMENSION AND WEIGHT
4.1 Overall dimensions (L x W x H) m To be filled in
4.2 Total weight kg To be filled in
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type To be filled in
1.4 Model To be filled in
1.5 Applicable Standards To be filled in
1.6 Configuration Duplicate
1.7 Type Test
Date of carried out To be filled in
Testing laboratory name and
To be filled in
country
Type test certificate to be issued by Yes/No Yes
24
independent laboratory or independently
witnessed type test will be acceptable to the
Employer
2 ELECTRICAL DATA
2.1 Auxiliary power supply through POE V DC 48 ±15%
2.2 Power consumption W To be filled in
Transmit(Maximum) A To be filled in
Receive(Maximum) A To be filled in
2.3 Rated Frequency Hz 50
2.4 VA <17W;Standard;
Power IEEE 802.3at
(PoE);
3 DESIGN DETAIL
3.1 Power output W To be filled in
3.2 RF Band: GHz 3.3 to 3.8 TDD
3.3 up to 120
Mbps UBR,
Data rate up to 100
Mbps
Ethernet rate
3.4 -40 to 75
Operating Temp °C
3.5 120Mbps UBR
with up to
Industry leading 100Mbps Ethernet
throughput using
2 × 2 MIMO
3.6 Lc TDD, ARQ &
adaptive
Per-link dynamic modulation/codin
g
3.7 Yes
All outdoor configurations with IEEE
802.3 at PoE
3.8 >280,000
Processing speed PPS
3.9 Yes
Surge Protection in Built-in: PoE and
RF ports
3.10 <10 ms
Latency
3.11 Yes
Redundancy (1+1 Hot Standby1
(PRP or RSTP compatible)
3.12 IP67 (IEC 60259)
Enclosure
3.13 rh%
Operating relative
humidity range non-
condensing)
3.14 BPSK 1/2 to 64 QAM
Modulation 5/6, 256 QAM
3.15 3 Mbps to 186.6
System Capacity Mbps UBR
3.16 150 km (93 mi)
Max Range
3.17 +30 dBm (Max
combined tx power,
Max Tx Power MIMO
mode/frequency band
specific)
3.18 External MIMO
Antenna Info
3.19 Dynamic Spectrum
Wireless QoS Access &
Management
3.20 512 Kbps to 100
Layer 2 Mbps
3.21 <10 ms
Latency
3.22 To be filled in
Management
3.23 3G and 4G/LTE
To be ideal for next generation networks
3.24
Details of forward error To be filled in
correction
3.25 Details of alarm monitoring facilities
To be filled in
3.26 Details of interfacing with the
Telecommunications Network Management To be filled in
System
3.27 Details of user interfaces
provided To be filled in
3.28 Dimensions (H×W×D)
mm To be filled in
3.29 Mass of complete equipment
kg To be filled in
26
3.30 Vibration
IEC Std To be filled in
3.31 Shock
IEC Std To be filled in
3.32 Mean Time to repair (MTTR)
h To be filled in
3.34 Mean Time between failure (MTBF)
h To be filled in
3.35 Manufacturer quality system in
accordance Y/N Yes
with ISO9000, 9001, 9002, 9003 and 9004
3.36 Used interfaces
Data interfaces
Voice interfaces
Teleprotection interface
Yes
ethernet
Antenna
4 - Manufacturer
- Model reference
- Place of manufacture
- Type and construction material
- Size mm
- Type
- Shape
- Frequency range
- Gain dB
- Half power beam degree
- Input impedance ohm
- Front to back ratio dB To be filled in
- Return loss dB
- Cross polarization discrimination dB
- Power handling W
- VSWR
- Termination
- Azimuth adjustment
4.1 Termination
To be filled in
4.2 Azimuth adjustment
degree To be filled in
4.3 Elevation adjustment
Degree To be filled in
4.4 Method of mounting
To be filled in
4.5 Wind Speed withstand
o Operational m/s To be filled in
o Survival
4.6 Protection rating
IP Std 67
4.7 Manufacturer quality system in
accordance Y/N Yes
with ISO9000, 9001, 9002, 9003 and 9004
4.8 Type test certificate to be issued by
independent laboratory or independently
Y/N Yes
witnessed type test will be acceptable to the
Employer
Antenna Feeder
Cable
5. - Manufacturer
- Type reference
- Place of manufacture
- Type and material of conductor
- Frequency range GHz
- Character impedance Ohm
- Nominal capacitance pF/m
- Attenuation dB/m
- Group delay Ns/m
- Peak power rating
W
- Type of screening
- Type of insulation
- Radial thickness of insulation
- Type of armouring (if any) mm
- Type of sheath
- Nominal overall diameter
- Minimum bending radius mm
- Are cable of flame retardant type? mm
- Cable mass Y/N
Yes
- Operating temperature range. Kg/m
C˚
6. Ethernet Rail Switch
28
6.4 Temperature
-40 C˚ to 70C˚
6.5 Remotely managed by Network
Management System (NMS).
Yes
7. 2 IP Telephone Yes
A GPS RECEIVER
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type To be filled in
1.4 Model To be filled in
1.5 Applicable Standards To be filled in
1.6 Location of service Indoor
1.7 Type Test
Date of carriedout To be filled in
Testing laboratory name and
To be filled in
country
CertificateProvided Yes
2 ELECTRICAL DATA
2.1 Rated voltage V DC 48 - 220VAC
2.2 Maximum power consumption W To be filled in
2.3 Rated frequency Hz 50
3 DESIGN DETAIL
3.1 Microprocessor based Yes
3.2 Time base Crystal
3.3 Display LED
Calendar:
3.4 Yes
Built-in calendar with leap years
3.5 Battery backup for time keeping Yes
3.6 12 or 24 hour mode Yes
3.7 Inputs GPS
3.8 Temperature Range
Maximum workingtemperature °C To be filled in
Minimum workingtemperature °C To be filled in
Non-volatile
3.9 Memory
EEPROM
3.10 Outputs RS485
3.11 Number of clock circuits 2
4 DIMENSION AND WEIGHT
4.1 Dimensions (L x W x H) mm To be filled in
4.2 Mounting (Wall type or Rack type) To be filled in
4.3 Weight kg To be filled in
B ANTENNA of GPS RECEIVER
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Type Active
1.3 Model To be filled in
1.4 Applicable Standards To be filled in
1.5 Location of service Outdoor
2 ELECTRICAL DATA
Operating voltage
2.1 V To be filled in
(Supply by Receiver)
2.2 Maximum power consumption W To be filled in
3 DESIGN DETAIL
3.1 Received Frequency MHz 1575.42±10
30
3.2 Input Impedance Ω 50
3.3 Temperature Range
Maximum workingtemperature °C To be filled in
Minimum workingtemperature °C To be filled in
3.4 Peak gain dB 30±3
3.5 Right Polarization Yes
3.6 V. S. W. R. ≤ 1.5:1
3.7 Noise dB ≤ 1.5
3.8 Housing Material PVC
3.9 Max. cable Length m To be filled in
3.10 Connector To be filled in
G ) Coaxial Cable
Technical Particulars and Guarantees of Coaxial Cable
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
With steel wire
1.3 Type
armoured type
1.4 Model To be filled in
IEC60502
1.5 Applicable Standards
&
IEC60228
2 ELECTRICAL DATA
2.1 Impedance 50+/-2 Ohms
2.2 Max. Conductor resistance Ohm/m To be filled in
2.3 Min. Insulation resistance M Ohm To be filled in
2.4 Capacitance pF/M To be filled in
2.5 Velocity of Propagation 66%
15dB (10 to 300
2.6 SRL MHz) 100% Swept
Tested
(dB
2.7 Attenuation at 50MHz To be filled in
/100M)
2.8 AC. Withstand voltage V To be filled in
3 DESIGN DETAIL
3.1 Number of conductor Core one
3.2 Cross sectional area mm² To be filled in
3.3 Material of conductor Bare Copper
3.4 Material of Dielectric PE
3.5 Material of sheath PVC/PE
3.6 Color of Outer Black
Bonded
3.7 Shield
Aluminum Foil
double galvanized
3.8 Armouring
steel wires
3.9 Minimum Bending Radius of cable mm 25
3.10 Overall diameter of cable (Approx.) mm To be filled in
3.11 Net weight (Approx.) (kg/km) To be filled in
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Fiber Multimode
1.4 Model
1.5 Applicable Standards IEC60793-2
1.6 Fiber Type 50/125µm
32
2 OPTICAL DATA
2.1 Minimum Bandwidth 850 nm MHz-km >500
2.2 Maximum Attenuation 850 nm dB-km <3.5
2.3 Group Index of Refraction 850 nm 1.483
2.4 Core Size Microns 50±3
2.5 Cladding Size Microns 125±2
2.6 Coating Size Microns 245±10
2.7 Buffer Size Microns 900±50
2.8 Core Cladding Concentricity Microns ≤3.0
3 PHYSICAL DATA
3.1 Number of fiber count To be filled in
3.2 Overall diameter of cable (Approx.) mm To be filled in
3.3 Material of fiber To be filled in
3.4 Maximum Pulling Tensions
Installation N To be filled in
LongTerm N To be filled in
3.5 Material of Outer PVC
3.6 Color of Outer To be filled in
3.7 Net weight (Approx.) kg/km To be filled in
3.8 Minimum Crush Resistance N/mm To be filled in
3.9 Minimum Flex Resistance Cycle To be filled in
3.10 Operating Temperature oC To be filled in
3.11 Minimum Bending Radius
Installation mm To be filled in
LongTerm mm To be filled in
2 ELECTRICAL DATA
2.1 Rated AC input current A 5
2.2 Rated AC input voltage V 110
2.3 Rated Frequency Hz 50
2.4 Insulation resistance at 500V megger MOhm >20
2.5 Dielectric strength (1 minute) ACKV 2
2.6 Mounting Flush mounting
2.7 Protection of housing IP 50
3 DESIGN DETAIL
3.1 Input consumption
CurrentCircuit VA To be filled in
VoltageCircuit VA To be filled in
3.2 Accuracy class Class 0.2 or 0.5
3.3 Number of AC input
Current 3 (R, Y, B)
Voltage 3 (R, Y, B)
34
Change-over of display of phase :
3.4 Push button
AC Current & Voltage
3.5 Display updating time Sec. To be filled in
3.6 Overload capacity
1.2 times
CurrentCircuit for
continuous
operation
1.2 times
VoltageCircuit for
continuous
operation
3.7 Auxiliary power supply V DC 48
3.8 Power consumption VA To be filled in
3.9 Color frame Semi-gloss black
• C.T:
Multi ratio programmable, class 0.2 or 1, burden not less than 30 VA.
• V.T:
Multi ratio programmable, class 0.2 or 1, burden 50 VA per phase.
K) Transducers
Technical Particulars and Guarantees of Transducers
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
36
1.2 Country of Manufacturing To be filled in
1.3 Type To be filled in
1.4 Standards To be filled in
2 ELECTRICAL DATA
2.1 Auxiliary supply voltage V DC 48
2.2 Operating current (CT secondary) A 5
L) LV AC Distribution Panel
38
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
Metal-clad totally
1.3 Type
enclosed
1.4 Model To be filled in
1.5 Applicable Standards IEC 60439
1.6 Location of services Indoor
1.7 Degree of protection IP 41
2 ELECTRICAL DATA
400/230V,±1
2.1 Rated AC voltage V
0%
3pase 4 wires
Power frequency
2.2 KVrms 3
withstand test voltage
2.3 Rated short circuit current , 1sec. KA 30
2.4 Control supply voltage
• Trip and closing coil V DC48
• Spring charging motors V DC48
3 DESIGN DETAIL
A AIR BREAK CIRCUIT BREAKER (INCOMING)
1.1 Manufacturer Name To be filled in
1.2 Type MCCB
1.3 Model To be filled in
1.4 Applicable Standards IEC 60947-2
1.5 Rated current A 150
Thermal &
1.6 Protection
Magnetic
B BUSBAR
Rated current of busbars at 55°C
2.1 A 250
ambient temperature
2.2 Busbar cross section mm2 To be filled in
2.3 Busbar insulation material To be filled in
C DETAILS OF MCBs
1.1 Manufacturer Name To be filled in
1.2 Type Molded
Case
1.3 Model To be filled in
1.4 Applicable Standards IEC 60947-2
1.5 Site current rating (at 55°C) A To be filled
1.6 Rated short time current (3 s) kA To be filled
1.7 Typical circuit diagram number To be filled
Thermal &
1.8 Protection
Magnetic
D DETAILS OF UNDER VOLTAGE PROTECTION
1.1 Manufacturer Name To be filled in
1.2 Type To be filled in
1.3 Model To be filled in
1.4 Catalogue Provided Yes
E INSTRUMENTS
1.1 Manufacturer Name To be filled in
1.2 Type of meter
• Voltmeter To be filled in
• Ammeter To be filled in
1.3 Catalogue Provided Yes
Single line diagram &
F To be filled in
Arrangement drawing number
4 DIMENSION AND WEIGHT
Overall dimensions of
Distribution Panel m To be filled in
(L x W x H)
Total weight of Distribution Panel kg To be filled in
1 GENERAL
1.1 Manufacturer Name To be filled in
40
1.2 Country of Manufacturing To be filled in
1.3 Type Numerical
1.4 Model To be filled in
IEC 60255/IEC
1.5 Applicable Standards
60068
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC 48
2.2 Maximum power consumption W To be filled in
2.3 Rated AC input current A 5
2.4 Maximum burden VA To be filled in
2.5 Rated AC input voltage V N/A
2.6 Maximum burden VA To be filled in
2.7 RatedFrequency Hz 50
2.8 Mounting Flush mounting
2.9 Protection of relay housing IP 50
3 DESIGN DETAILS
3.1 Over current relay
• Current settingrange % To be filled in
• Current settingrange % To be filled in
(Instantaneous)
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type To be filled in
1.4 Model To be filled in
IEC 60255/IEC
1.5 Applicable Standards
60068
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC 48
3 DESIGN DETAILS
3.1 Voltage of monitored circuit V DC 48
3.2 Measuring current typ. mA To be filled in
3.3 Operate delay time Sec. To be filled in
Supervision of the whole trip
3.4 Yes
circuit with CB open and closed.
3.5 Relay operatedindicator/LED Yes
3.6 Output Relay
42
• 2 x C(1a+1b) Yes
• Rated voltage 250 VAC/DC
• Rated current ofcontacts
A To be filled in
• -Continuous
O) Multi Contact Tripping Relay
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type To be filled in
1.4 Model To be filled in
IEC 60255/IEC
1.5 Applicable Standards
60068
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC48
3 DESIGN DETAILS
3.1 Number of Contacts To be filled in
3.2 Ratedvoltage 250 VAC/DC
Rated current of contacts
3.3 A To be filled in
-Continuous
3.4 Operating time To be filled in
Is relay mechanically latched or
3.5 To be filled in
self resetting
Method used to reset latched relay
3.6 To be filled in
(hand or electrical)
3.7 Burden at rated voltage To be filled in
Minimum voltage at which
3.8 To be filled in
reliable operation occurs
3.9 Relay operated indicator type To be filled in
44
45
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type Numerical
1.4 Model To be filled in
IEC
1.5 Applicable Standards
60255/IE
C 60068
1.6 Type Test
• Date of carriedout To be filled in
• Testing laboratory nameand To be filled in
• Certificate Provided Yes
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC 48
2.2 Maximum power consumption W To be filled in
2.3 Rated AC input voltage V 110
2.4 Maximum burden VA To be filled in
2.5 Rated Frequency Hz 50
2.6 Mounting Flush mounting
2.7 Protection of relay housing IP 50
3 DESIGN DETAILS
Number of programmable
3.1 To be filled in
output relays
Independent time delay setting
3.2 Yes
for each stage
3.3 Number of frequency stages 4
3.4 Frequency setting range Hz To be filled
in
3.5 Delay times sec To be filled
in
3.6 df/dt testing range To be filled
in
46
47
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type Numerical
1.4 Model To be filled in
IEC 60255/IEC
1.5 Applicable Standards
60068
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC 48
2.2 Maximum power consumption W To be filled in
2.3 Rated voltage (Un) V 110
2.4 Continuous withstand V 2 x Un
2.5 Maximum burden VA To be filled in
2.6 Rated Frequency Hz 50
2.7 Mounting Flush mounting
2.8 Protection of relay housing IP 50
3 DESIGN DETAIL
3.1 Start Voltage Uo>0 To be filled in
3.2 Start time, typically To be filled in
3.3 Operate time t> To be filled in
3.4 Drop-off/pick-up ratio, typically To be filled in
3.5 Setting range To be filled in
4 COMMUNICATIONS
Front panel localPC
4.1 To be filled in
communicationport
Rear panel RTU fiber
4.2 optic communication Yes
port
4.3 Name of protocols (IEC60870-5-103) Yes
Ether LAN Interface
4.4 Yes
communication port (IEC61850)
4.5 Transmission speed To be filled in
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type Numerical
1.4 Model To be filled in
IEC 60255/IEC
1.5 Applicable Standards
60068
2 ELECTRICAL DATA
2.1 Auxiliary power supply V DC48
2.2 Maximum power consumption W To be filled in
2.3 Rated AC input voltage V 111
2.4 Maximum burden VA To be filled in
2.5 RatedFrequency Hz 50
2.6 Mounting Flush mounting
2.7 Protection of relay housing IP 50
3 DESIGN DETAIL
3.1 Voltage setting range To be filled in
3.2 Voltage/time characteristics To be filled in
3.3 Time delay setting range To be filled in
3.4 Voltage pick up/resetratio To be filled in
4 COMMUNICATIONS
Front panel localPC
4.1 To be filled in
Communicationport
Rear panel RTU fiber
4.2 Yes
optic communication
4.3 Name of protocols (IEC60870-5-103) Yes
Ether LAN Interface
4.4 Yes
communication port (IEC61850)
4.5 Transmission speed To be filled in
1 GENERAL
1.6 Manufacturer Name To be filled in
1.7 Country of Manufacturing To be filled in
1.8 Type Numerical
1.9 Model To be filled in
IEC 60255/IEC
1.10 Applicable Standards
60068
2 ELECTRICAL DATA
2.8 Auxiliary power supply V DC48
2.9 Maximum power consumption W To be filled in
2.10 Rated AC input voltage V 110
2.11 Maximum burden VA To be filled in
2.12 RatedFrequency Hz 50
2.13 Mounting Flush mounting
2.14 Protection of relay housing IP 50
3 DESIGN DETAIL
3.12 Voltage setting range To be filled in
3.13 Voltage/time characteristics To be filled in
3.14 Time delay setting range To be filled in
3.15 Voltage pick up/resetratio To be filled in
4 COMMUNICATIONS
Front panel localPC
4.6 To be filled in
communicationport
Rear panel SCS fibre
4.7 Yes
optic communication
4.8 Name of protocols (IEC60870-5-103) Yes
Ether LAN Interface
4.9 Yes
communication port (IEC61850)
4.10 Transmission speed To be filled in
50
51
Technical Particulars and Guarantees of 33 kV XLPE insulated Single core Power Cables
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
(Accordingto
1.3 Type MoE
specifications
)
1.4 Rated voltage(Uo/U) kV 18/30
1.5 Highest system voltage (Umax) kV 36
IEC60502-2 &
1.6 Applicable Standards
IEC60228
1.7 Type Test
• CertificateProvided Yes
2 ELECTRICAL DATA
2.1 Rated Frequency Hz 50
2.2 AC. Withstand voltage for 5 minutes kV rms 63
2.3 Impulsewithstandvoltage(1.2/50µs) kV peak 170
2.4 Max. DC Conductor resistance at ohm/km 0.387
2.5 Max. Temperature rating of ◦C 90
3 DESIGN DETAIL
3.1 Number of conductor Core 1
3.2 Cross sectional area (Phase) mm² 50
Compacted
3.3 Shape of Conductor
circular
stranded
Annealed
3.4 Material of Conductor
Copper
Wires
3.5 Weight of Conductor (Approx.) kg/km To be filled in
3.6 Material of insulation XLPE
3.7 Insulation thickness (Nominal) mm 8
Technical Particulars and Guarantees of LV PVC insulated Single core Power Cables
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
(Accordingto
1.3 Type MoE
specifications
)
1.4 Rated voltage(Uo/U) kV 0.6/1.0
IEC60502-1 &
1.5 Applicable Standards
IEC60228
2 ELECTRICAL DATA
2.1 RatedFrequency Hz 50
2.2 AC. Withstand voltage V 3500
52
53
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type CU/PVC/PVC
1.4 Rated voltage(Uo/U) kV 0.6/1.0
IEC60502-1
1.5 Applicable Standards
&
IEC60228
2 ELECTRICAL DATA
2.1 RatedFrequency Hz 50
2.2 AC. Withstand voltage V 3500
2.3 Max. Temperature rating of ◦C 90
3 DESIGN DETAILS
3.1 Number of conductor Core To be filled in
As per
3.2 Cross sectional area (Phase) mm²
specification
Compacted
3.3 Shape of conductor
circular
stranded
Annealed
3.4 Material of conductor
Copper
Wires
3.5 Material of insulation PVC
3.6 Material of sheath PVC
3.7 Color of sheath Black
Overall diameter of cable
3.8 mm To be filled in
(Approx.) Each of cables
3.9 Net weight (Approx.) kg/km To be filled in
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type CU/PVC/PVC
1.4 Rated voltage(Uo/U) kV 0.6/1.0
IEC60502-1 &
1.5 Applicable Standards
IEC60228
2 ELECTRICAL DATA
2.1 RatedFrequency Hz 50
2.2 AC. Withstand voltage V 3500
2.3 Max. Temperature rating of ◦C 90
54
55
3 DESIGN DETAIL
3.1 Number of conductor Core Multi
3.2 Cross sectional area mm² Min. 1.5
Compacted
3.3 Shape of conductor
circular
stranded
Annealed
3.4 Material of conductor
Copper
Wires
3.5 Material of insulation PVC
3.6 Material of sheath PVC
3.7 Color of sheath Black
Bonded
3.8 Shield
Aluminum
Foil
double
3.9 Armouring
galvanized
steelwires
3.10 Overall diameter of cable (Approx.) mm To be filled in
3.11 Net weight (Approx.) kg/km To be filled in
Y) Grounding System
Technical Particulars and Guarantees of Grounding System
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
Bare stranded
1.3 Type annealed
copper Wires
IEC60502 &
1.4 Applicable Standards
IEC60228,
BS6360
2 DESIGN DETAIL
2.1 Main ground grid conductor Copper
2.2 Standards IEEE 80
2.3 Main ground grid conductor size mm2 ≥ 95
Depth and burial of main
2.4 mm To be filled in
ground conductor
2.5 Length and diam. of ground rod mm 2500/19
2.6 Material of ground rod Copper weld
Z) Ampere Meters
Technical Particulars and Guarantees of Ampere Meters for incmers, Feeder, Bus &
Aux.TR
Specification
No. Description Unit
Required Proposed
1 GENERAL
1.1 Manufacturer Name To be filled in
1.2 Country of Manufacturing To be filled in
1.3 Type Numerical
1.4 Model To be filled in
IEC 60051 and
1.5 Applicable Standards
IEC61554
2 ELECTRICAL DATA
2.1 Rated AC input current A 5
2.2 Maximum burden VA To be filled in
2.3 RatedFrequency Hz 50
2.4 Insulation resistance at 500V megger MOhm >20
2.5 Dielectric strength (1 minute) ACKV 2
2.6 Mounting Flush mounting
2.7 Protection of housing IP 50
3 DESIGN DETAIL
3.1 Scale 30, 300,600
Number of AC input
3.2 3 (R, Y, B)
Current
3.3 Accuracy class Class 0.2
3.4 Maximum demand Yes
3.5 Color frame Semi-gloss black
56