II Mid Examinations Objective JUNE- 2022 SUB: 15A02801 Instrumentation Time: 20min Max. Marks: 10M Roll No: ______________________ Name:________________________________________ Answer all of the following: 20 X ½ =10M 1. Wave analyzer is an instrument used to measure [ ] a) relative amplitude b) relative frequency c) Frequency spectrum d) None 2. Application of wave analyzer [ ] a) range measurement b) sound measurement c) current measurement d) None 3. The unwanted noise signals other than sinusoidal signals is called as [ ] a) error b) accuracy c) distortion d) resolution 4. Choose the type of Spectrum Analyzer [ ] a) RF spectrum analyzer b) AF spectrum analyzer c) None d) Both a & b 5. Vector impedance meter can measure [ ] a) Phase angle and magnitude b) Phase angle c) Angle d) Any one at time 6. The input signal is converted into trigger pulses in [ ] a) Phase vector meter b) Digital frequency meter c) DVM d) None 7 Tachometers are used to measure [ ] a) Span b) Precision c) Speed d) None 8. The process of converting one form of energy into other form is called as [ ] a) Sensor b) Transducer c) Transformation d) Transduction 9. Thermo couple works under the following principle [ ] a) See back effect b) Mutual inductance c) Faradays effect d) None 10. Resistance potentiometer is a [ ] a) Mechanical b) Passive Transducer c) Active transducer d) None of the above Transducer 11. Inverse transducer converts [ ] a) electrical to b) electrical to motion c) electrical to non- d) electrical to Triggering mechanical electrical pulses 12. To avoid loading effect of a transducer the input impedance should be ____________. [ ] a) less b) zero c) more d) very high 13. LVDT is an _____________ transducer [ ] a) Inductive b) Impedance c) Insulative d) Capacitive 14. The mechanical displacement is converted into resistance in _____________ [ ]
a) Wheatstone bridge b) strain gauge c) LVDT d) Capacitive transducer
15. The unit change in resistance per unit change in length is called _________ [ ] a) Form Factor b) Load Factor c) Gauge factor d) Relative factor 16. Thermistor is used to measure [ ] a) Resolution b) Quantization c) Modulation d) Temperature 17. The two terminal semiconductor device whose terminal resistance varies with incident light is [ ] called ________________ a) Photo conductive b) Solar cell c) LED d) LCD cell 18. A reverse biased semiconductor device which converts light into current is called [ ] a) Zener diode b) Photo diode c) Light emitting diode d) thermistor 19. Mechanical stress or vibrations are converted into electrical signals in [ ] a) Temperature b) Capacitive c) Piezo electric d) All the above transducer transducer transducer 20. Accelerometer is used to measure [ ] a) speed b) velocity c) amplitude d) Force IVB.Tech II Semester BRANCH: EEE-A& B II-Mid Examinations Descriptive JUNE-2022 SUB: Instrumentation Time: 90min Max. Marks: 20M Answer any Three of the following questions: 3 X 10 =30M Cos Levels Questions Mark s 1 CO4 L2 A) Draw the block diagram of successive approximation DVM. 2M 10 L4 B) Explain with neat diagram, the working of digital frequency meter. 8M 2 CO5 L4 A)Classify the transducers. 2M 10 b)What is inductive transducer? Explain different types of inductive transducers with neat sketches. 8M 3 CO5 L4 A)Write short notes on strain gauges 2M 10 B)Explain the principle and working of piezoelectric transducers and LVDT transducer. 8M 4 CO3 L2 A)What are the differences between thermocouples and thermistors?2M 10 B)Describe the principle and working of thermocouples. 8M 5 CO4 L6 A)Define pyrometers. 2M 10 B)Describe the principle and working of any one pressure sensor. 8M
Answer any Three of the following questions: 3 X 10 =30M
Cos Levels Questions Mark s 1 CO4 L2 A) Draw the block diagram of successive approximation DVM. 2M 10 L4 B) Explain with neat diagram, the working of digital frequency meter. 8M 2 CO5 L4 A)Classify the transducers. 2M 10 b)What is inductive transducer? Explain different types of inductive transducers with neat sketches. 8M 3 CO5 L4 A)Write short notes on strain gauges 2M 10 B)Explain the principle and working of piezoelectric transducers and LVDT transducer. 8M 4 CO3 L2 A)What are the differences between thermocouples and thermistors?2M 10 B)Describe the principle and working of thermocouples. 8M 5 CO4 L6 A)Define pyrometers. 2M 10 B)Describe the principle and working of any one pressure sensor. 8M
3.3.3 Number of Books and Chapters in Edited Volumes/books Published and Papers Published in National/ International Conference Proceedings Per Teacher During Last Five Years