Professional Documents
Culture Documents
H OME BUS IN ES S AN ALYS IS QUARTER RES ULTS :AN ALYS IS CON CALL KEY POIN TS EN GIN EERIN G EN GIN EERIN G MAIN TEN AN CE
RECENT UPDATES
Engineering Materials
TYPES OF STRESS IN STRENGTH OF MATERIALS COMPANIES WITH BETTER PRODUCT
QUALITIES AND SERVICES
in
Engineering Materials
We were
discussing the concept of stress and strain in our previous post; now we are
going further to start our discussion for
classifying the stress and strain. Hence,
we will see here the types of stress and strain with the help of this post.
Types of stress
report this a
There are
following type of stresses as displayed in figure here and we will discuss each
type of stress in detail with the help of
this post. Basically stresses are
classified in to three types. SEARCH THE TOPIC HERE
1. Direct
stress or simple stress
report this ad
2. Indirect
stress
3. Combined
stress
DROP MAIL ID AND JOIN US
Further direct stress or simple stress is classified in two type i.e. normal stress and
shear stress. As it is also displayed in figure,
Enter your email address:
normal stress will be divided
in two type i.e. tensile stress and compressive stress.
Subscribe x
Similarly,
indirect stress will also be divided in two type i.e. torsion stress and
bending stress. Above figure displayed here Delivered by FeedBurner
128
indicates
Sharesthe brief introduction
for the classification of stress in strength of material.
Normal stress x
POPULAR POSTS
Normal
stress is basically defined as the stress acting in a direction perpendicular
to the area. Normal stress will be further
DERIVE RELATION BETWEEN
divided, as we have seen above, in
two types of stresses i.e. tensile stress and compressive stress. YOUNG'S MODULUS BULK
Tensile stress MODULUS AND POISSON RAT
Let us see
here the following figure; we have one bar of length L. There are two equal and
opposite pulling type of forces P, PROVE THAT INTERNAL ENER
acting axially and trying to pull the bar
and this pulling action will be termed as tensile and stress developed in material
of the A PROPERTY OF THE SYSTEM
Tensile stress
(σt) = Resisting force (R) / Cross sectional area (A) PLUMBING TOOLS AND THEIR
WITH PICTURES
Tensile
stress (σt) =Tensile load or applied load (P) / Cross sectional area
(A)
σt = P/A
MAJOR AND MINOR LOSSES IN
PIPES
Ad removed.
Details ADVANTAGES, DISADVANTAG
AND APPLICATIONS OF HELIC
GEARS
Compressive stress
Let us see
here the following figure; we have one bar of length L. There are two equal and
opposite push type of loading P,
acting axially and trying to push the bar and
this pushing action will be termed as compression and stress developed in
material
of the bar will be termed as compressive stress.
report this a
Therefore
we can define the compressive stress as the stress developed in a member due to
the pushing action of two equal
and opposite direction of forces. σc
is the symbol which is used to represent the compressive stress in a member.
There will
be decrease in the length of the bar under the action of compressive loading,
but diameter of the bar will be
increased under the action of compressive
loading. Compressive stress will be determined with the help of following
formula.
Compressive
stress (σc) = Resisting force (R) / Cross sectional area (A)
Compressive
stress (σc) = Compressive load or applied load (P) / Cross sectional
area (A)
σc = P/A
Shear stress x
128
Shares
Let us see here the following figure; we have two plates and these two plates are
connected with each other with the help of a x
pin or a rivet as shown in figure.
There are two equal and opposite forces (P) acting tangentially across the
resisting section.
One force
is acting on top plate towards left direction and second force is acting
towards right side as shown in figure and
hence such type of loading will try
to shear off the body across the resisting section.
This type
of loading action will be termed as shear loading and stress developed in
material of the body will be termed as shear
stress.
Therefore
we can define the shear stress as the stress developed in a member, when member
will be subjected with two equal
and opposite forces acting tangentially across
the resisting section. τ is the symbol which is used to represent the shear
stress in
a member. Shear resistance R will be equivalent to P here.
Shear
stress (τ) = P/A
As we have
seen above in figure, two plates are connected with each other with the help of
a pin and therefore we can also say
such type of loading as single shear. Let
we have three plates and these three plates are connected with a pin or rivet,
such type
of loading will be termed as double shear. Shear resistance R will be
P/2.
Shear
stress (τ) = P/2A
Torsional stress
Let if
bearing is seized, then there will be twisting mechanism because one end of
rotating shaft will be fixed due to seized
bearing and other end of shaft will
be twisted and therefore there will be produced stress in shaft and that stress
will be termed
as torsional stress.
From here,
we can also say that torsional stress will exist in rotating members such as
rotating shaft. Torsional stress will be
indicated by symbol
Bending stress
Let we
have one beam which one end is fixed at A and other end is loaded by force P
and hence beam is deflected here as
shown in figure.
x
128
Shares
x
Bending stress
will be determined with the help of following formula as displayed here in
following figure.
We will
study and analyze each type of strain in detail in our next post.
Reference:
Cements and
its types
Safety
requirement in cement industries
Cement
kiln firing system
Objective
of total productive maintenance
Maintenance
practice and procedure
report this ad
Engineering Materials
10 C O M M ENT S :
UNKNOWN 10:19
Good work
Reply
SUBWAYSUBFERS 22:17
Interesting and interesting information can be found on this topic here profile worth to see it. how much cbd oil should i
take uk
x
Reply
128
Shares
JONE MARTIN 22:09 x
In physics, we heard about this little bit. You describe it about briefly and in easily way. Likely, you helping the people, I
am also helping the people from provide the Air Conditioner Repair in Fort Worth TX. They can get more detail about it.
Reply
FRANK 23:10
the compressive stress as the stress developed in a member Write My Essay' due to the pushing action of direction of
forces.
Reply
TSP-SCOTLAND 16:44
Very well explained i took very interest while reading. Good Work. Butcher Supplier
Reply
MOHSIN 13:45
This is my first visit to your web journal! We are a group of volunteers and new activities in the same specialty. Website
gave us helpful data to work. stress balls to buy
Reply
I like your data because there are many types of stress, but some of them are very common, which you have
mentioned here like compression, tension, shear, bending, torsion, and fatigue, but all these are harmful to health.
Thanks for providing me with such useful information. Buy Essay Online
Reply
I liked your information it tells about all the major aspects of life. PHD dissertation writing services.
Reply
FAREED 13:42
I would like to say that this blog really convinced me to do it! Thanks, very good post.
https://www.evernote.com/shard/s357/sh/f480fe94-74e5-0034-506e-
f1b5b350a7ba/5e0acf5eb84c408c9985a7e80432a3e7
Reply
If you are seeking Thesis Writing Services In Pakistan for thesis writing tasks. You can contact us as we are the best
service that is providing thesis help, we have the best team of writers.
Reply
128
Shares
x
Name
ENGINEERING MAINTENANCE
QUARTER RESULTS:ANALYSIS
I am Harikesh Kumar Divedi, a mechanical engineer
and founder of Engineering Made Easy- A website for RENEWABLE ENERGY RESOURCES
mechanical engineering professional. I am working
for a reputed and quality brand organization, I am STEEL AND CEMENT TECHNOLOGY
much interested to write and discuss engineering
articles and hence i always spends my spare time in THERMAL ENGINEERING AND POWER UNIT
writing engineering article.
Read More......
128
Designed with by Way2Themes | Distributed By Gooyaabi Templates
Shares
x
128
Shares