Professional Documents
Culture Documents
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 45.54-kN *Soil Weight is not included
Side Resistance (Down)= 467.421-kN Side Resistance (Up)= 444.892-kN
Tip Resistance (Down)= 252.702-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 720.124-kN Total Ultimate Capacity (Up)= 490.429-kN
Total Allowable Capacity (Down)= 437.965-kN Total Allowable Capacity (Up)= 267.983-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 437.00-kN Settlement= 0.09606-cm
At Xallow= 2.50-cm Qallow= 686.64752-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 437.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 437.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.6 27.2 32.6 96.3 0.83 11
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
11.0 50 3062.7 157.1 320535.8 25000 5.719
Concrete (rough)
12 12
12.0 50 1963.5 157.1 320535.8 25000 5.719 12.0 11.2 0.0 143.0 278.5 0.51 24
Pile Tip Stiff Clay
13 13
14 14
15 15
800
720
640
Compression Load, Qdw -kN
560
480
400
320
240
160
80
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
500 500
450 450
400 400
Compression Capacity, Qdw -kN
350 350
250 250
200 200
150 150
100 100
50 50
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 437.00 -kN
Shear= 295.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.49000-cm
Max. Moment, M= 554.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
yt=0 at 5.6-m
6 6
St=0 at 6.7-m
7 7
8 8
9 9
10 10
11 11
12 12
Tip yt=-1.68E-4 Top yt=2.49E+0 Top Moment=-554.0 Top Shear=295.0
Max. yt=2.49E+0 Max. Moment=554.0 Max. Shear=300.0 Max. Pressure=53.00
Top St=1.43E-17
13 13
14 14
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.5 0.0 437.0 0.1 0.00 32.7
2 88.5 0.0 437.0 0.4 0.00 131.0
14 3 148.0 0.0 437.0 0.9 0.00 245.0 14
4 206.0 0.0 437.0 1.5 0.00 365.0
5 236.0 0.0 437.0 1.8 0.00 425.0
15 6 266.0 0.0 437.0 2.1 0.00 487.0 15
7 295.0 0.0 437.0 2.5 0.00 554.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.5 0.0 437.0 0.1 0.00 32.7
2 88.5 0.0 437.0 0.4 0.00 131.0
14 3 148.0 0.0 437.0 0.9 0.00 245.0 14
4 206.0 0.0 437.0 1.5 0.00 365.0
5 236.0 0.0 437.0 1.8 0.00 425.0
15 6 266.0 0.0 437.0 2.1 0.00 487.0 15
7 295.0 0.0 437.0 2.5 0.00 554.0
300 300
270 270
240 240
210 210
180 180
Lateral Load, P -kN
120 120
90 90
60 60
30 30
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 60 120 180 240 300 360 420 480 540 600
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
700000
630000
560000
490000
p, -kN/m
420000
350000
280000
210000
140000
70000
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.5, 3.0, 4.5, 6.0, 7.5, 9.0, 10.5 -m
M= 0, P= 295.00 -kN
Results:
At Shear= 295.00-kN, Top Deflection, yt= 12.50000-cm
Stiffness Kpy= 23.60-kN/-cm
At Shear= 295.00-kN, Top Slope, St= -0.03760 Slope
Stiffness Kps= -7845.74-kN/Slope
Or St= -2.15330696 Degree, Stiffness Kps= -137.00-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.01690-cm
Stiffness Kmy= 591.72-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00020 Slope
Stiffness Kms= -49019.61-kN-m/Slope
Or St= -0.01168834 Degree, Stiffness Kms= -855.55-kN-m/Degree
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø500mm-14m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 53.13-kN *Soil Weight is not included
Side Resistance (Down)= 519.708-kN Side Resistance (Up)= 497.221-kN
Tip Resistance (Down)= 252.702-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 772.411-kN Total Ultimate Capacity (Up)= 550.348-kN
Total Allowable Capacity (Down)= 472.823-kN Total Allowable Capacity (Up)= 301.738-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 472.00-kN Settlement= 0.09712-cm
At Xallow= 2.50-cm Qallow= 733.38062-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 472.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 472.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.6 27.2 32.6 96.3 0.83 11
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
12 12
13 13
13.0 50 3062.7 157.1 320535.8 25000 5.719
Concrete (rough)
14 14
14.0 50 1963.5 157.1 320535.8 25000 5.719 14.0 11.2 0.0 143.0 278.5 0.51 24
Pile Tip Stiff Clay
15 15
800
720
640
Compression Load, Qdw -kN
560
480
400
320
240
160
80
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
500 500
450 450
400 400
Compression Capacity, Qdw -kN
350 350
250 250
200 200
150 150
100 100
50 50
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 472.00 -kN
Shear= 290.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.44000-cm
Max. Moment, M= 544.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
yt=0 at 5.6-m
6 6
St=0 at 6.7-m
7 7
8 8
9 9
10 10
11 11
12 12
13 13
14 14
Tip yt=-2.23E-5 Top yt=2.44E+0 Top Moment=-544.0 Top Shear=290.0
Max. yt=2.44E+0 Max. Moment=544.0 Max. Shear=292.9 Max. Pressure=52.50
Top St=-1.23E-17
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.0 0.0 472.0 0.1 0.00 32.1
2 87.0 0.0 472.0 0.4 0.00 129.0
14 3 145.0 0.0 472.0 0.9 0.00 241.0 14
4 203.0 0.0 472.0 1.5 0.00 359.0
5 232.0 0.0 472.0 1.8 0.00 418.0
15 6 261.0 0.0 472.0 2.1 0.00 479.0 15
7 290.0 0.0 472.0 2.4 0.00 544.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 29.0 0.0 472.0 0.1 0.00 32.1
2 87.0 0.0 472.0 0.4 0.00 129.0
14 3 145.0 0.0 472.0 0.9 0.00 241.0 14
4 203.0 0.0 472.0 1.5 0.00 359.0
5 232.0 0.0 472.0 1.8 0.00 418.0
15 6 261.0 0.0 472.0 2.1 0.00 479.0 15
7 290.0 0.0 472.0 2.4 0.00 544.0
300 300
270 270
240 240
210 210
180 180
Lateral Load, P -kN
120 120
90 90
60 60
30 30
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 60 120 180 240 300 360 420 480 540 600
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.8, 3.5, 5.3, 7.0, 8.8, 10.5, 12.3 -m
M= 0, P= 290.00 -kN
Results:
At Shear= 290.00-kN, Top Deflection, yt= 12.30000-cm
Stiffness Kpy= 23.58-kN/-cm
At Shear= 290.00-kN, Top Slope, St= -0.03690 Slope
Stiffness Kps= -7859.08-kN/Slope
Or St= -2.11325550 Degree, Stiffness Kps= -137.23-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.01690-cm
Stiffness Kmy= 591.72-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00020 Slope
Stiffness Kms= -49019.61-kN-m/Slope
Or St= -0.01168834 Degree, Stiffness Kms= -855.55-kN-m/Degree
M= 0, P= 290.00 -kN
Results:
At Shear= 290.00-kN, Top Deflection, yt= 2.44000-cm
Stiffness Kpy= 118.85-kN/-cm
At Shear= 290.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø500mm-16m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 60.72-kN *Soil Weight is not included
Side Resistance (Down)= 573.874-kN Side Resistance (Up)= 551.336-kN
Tip Resistance (Down)= 252.702-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 826.577-kN Total Ultimate Capacity (Up)= 612.053-kN
Total Allowable Capacity (Down)= 508.934-kN Total Allowable Capacity (Up)= 336.385-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 508.00-kN Settlement= 0.10006-cm
At Xallow= 2.50-cm Qallow= 779.01764-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 508.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 508.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
8 8
10 10
12 12
14 14
20 20
22 22
24 24
26 26
28 28
30 30
900
810
720
Compression Load, Qdw -kN
630
540
450
360
270
180
90
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
600 600
540 540
480 480
Compression Capacity, Qdw -kN
420 420
300 300
240 240
180 180
120 120
60 60
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 508.00 -kN
Shear= 295.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.49000-cm
Max. Moment, M= 554.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
2 2
4 4
yt=0 at 5.6-m
6 6
St=0 at 6.7-m
8 8
10 10
12 12
14 14
16 16
Tip yt=3.8E-6 Top yt=2.49E+0 Top Moment=-554.0 Top Shear=295.0
Max. yt=2.49E+0 Max. Moment=554.0 Max. Shear=300.0 Max. Pressure=53.00
Top St=2.15E-17
18 18
20 20
22 22
24 24
26 26
28 28
30 30
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 29.5 0.0 508.0 0.1 0.00 32.7
2 88.5 0.0 508.0 0.4 0.00 131.0
28 3 148.0 0.0 508.0 0.9 0.00 245.0 28
4 206.0 0.0 508.0 1.5 0.00 365.0
5 236.0 0.0 508.0 1.8 0.00 425.0
30 6 266.0 0.0 508.0 2.1 0.00 487.0 30
7 295.0 0.0 508.0 2.5 0.00 554.0
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 29.5 0.0 508.0 0.1 0.00 32.7
2 88.5 0.0 508.0 0.4 0.00 131.0
28 3 148.0 0.0 508.0 0.9 0.00 245.0 28
4 206.0 0.0 508.0 1.5 0.00 365.0
5 236.0 0.0 508.0 1.8 0.00 425.0
30 6 266.0 0.0 508.0 2.1 0.00 487.0 30
7 295.0 0.0 508.0 2.5 0.00 554.0
300 300
270 270
240 240
210 210
180 180
Lateral Load, P -kN
120 120
90 90
60 60
30 30
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 60 120 180 240 300 360 420 480 540 600
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 2.0, 4.0, 6.0, 8.0, 10.0, 12.0, 14.0 -m
M= 0, P= 295.00 -kN
Results:
At Shear= 295.00-kN, Top Deflection, yt= 12.70000-cm
Stiffness Kpy= 23.23-kN/-cm
At Shear= 295.00-kN, Top Slope, St= -0.03810 Slope
Stiffness Kps= -7742.78-kN/Slope
Or St= -2.18191385 Degree, Stiffness Kps= -135.20-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.01700-cm
Stiffness Kmy= 588.24-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00021 Slope
Stiffness Kms= -48780.49-kN-m/Slope
Or St= -0.01174563 Degree, Stiffness Kms= -851.38-kN-m/Degree
M= 0, P= 295.00 -kN
Results:
At Shear= 295.00-kN, Top Deflection, yt= 2.49000-cm
Stiffness Kpy= 118.47-kN/-cm
At Shear= 295.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø600mm-12m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 65.58-kN *Soil Weight is not included
Side Resistance (Down)= 628.824-kN Side Resistance (Up)= 601.682-kN
Tip Resistance (Down)= 306.123-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 934.946-kN Total Ultimate Capacity (Up)= 667.264-kN
Total Allowable Capacity (Down)= 572.277-kN Total Allowable Capacity (Up)= 366.423-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 570.00-kN Settlement= 0.11067-cm
At Xallow= 2.50-cm Qallow= 909.28967-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
OTAL LOADS:
Vertical Load, Q: 570.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 570.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.4 29.5 27.5 75.1 0.92 9
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
11.0 60 4410.2 188.5 664662.9 25000 8.236
Concrete (rough)
12 12
12.0 60 2827.4 188.5 664662.9 25000 7.069 12.0 11.0 0.0 120.3 222.4 0.57 20
Pile Tip Stiff Clay
13 13
14 14
15 15
1000
900
800
Compression Load, Qdw -kN
700
600
500
400
300
200
100
0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Settlement, X -cm
Total Side Tip
600 600
540 540
480 480
Compression Capacity, Qdw -kN
420 420
300 300
240 240
180 180
120 120
60 60
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
ILE PROFILES:
Pile Length, L= 12.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 555.00 -kN
Shear= 405.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.45000-cm
Max. Moment, M= 860.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
6 6
yt=0 at 6.4-m
St=0 at 0.1-m
7 7
8 8
9 9
10 10
11 11
12 12
Tip yt=7.32E-3 Top yt=2.45E+0 Top Moment=-860.0 Top Shear=405.0
Max. yt=2.45E+0 Max. Moment=860.0 Max. Shear=408.3 Max. Pressure=52.08
Top St=1.43E-17
13 13
14 14
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.5 0.0 555.0 0.1 0.00 49.9
2 122.0 0.0 555.0 0.4 0.00 203.0
14 3 202.0 0.0 555.0 0.9 0.00 380.0 14
4 284.0 0.0 555.0 1.5 0.00 569.0
5 324.0 0.0 555.0 1.8 0.00 665.0
15 6 364.0 0.0 555.0 2.1 0.00 762.0 15
7 405.0 0.0 555.0 2.5 0.00 860.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.5 0.0 555.0 0.1 0.00 49.9
2 122.0 0.0 555.0 0.4 0.00 203.0
14 3 202.0 0.0 555.0 0.9 0.00 380.0 14
4 284.0 0.0 555.0 1.5 0.00 569.0
5 324.0 0.0 555.0 1.8 0.00 665.0
15 6 364.0 0.0 555.0 2.1 0.00 762.0 15
7 405.0 0.0 555.0 2.5 0.00 860.0
500 500
450 450
400 400
350 350
300 300
Lateral Load, P -kN
200 200
150 150
100 100
50 50
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 90 180 270 360 450 540 630 720 810 900
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
800000
720000
640000
560000
p, -kN/m
480000
400000
320000
240000
160000
80000
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.5, 3.0, 4.5, 6.0, 7.5, 9.0, 10.5 -m
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 11.50000-cm
Stiffness Kpy= 35.22-kN/-cm
At Shear= 405.00-kN, Top Slope, St= -0.03060 Slope
Stiffness Kps= -13235.29-kN/Slope
Or St= -1.75270391 Degree, Stiffness Kps= -231.07-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00973-cm
Stiffness Kmy= 1027.75-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00010 Slope
Stiffness Kms= -96153.84-kN-m/Slope
Or St= -0.00595876 Degree, Stiffness Kms= -1678.20-kN-m/Degree
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 2.45000-cm
Stiffness Kpy= 165.31-kN/-cm
At Shear= 405.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø600mm-14m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 76.51-kN *Soil Weight is not included
Side Resistance (Down)= 623.581-kN Side Resistance (Up)= 596.604-kN
Tip Resistance (Down)= 363.886-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 987.468-kN Total Ultimate Capacity (Up)= 673.116-kN
Total Allowable Capacity (Down)= 597.664-kN Total Allowable Capacity (Up)= 374.814-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 595.00-kN Settlement= 0.11533-cm
At Xallow= 2.50-cm Qallow= 964.73578-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 595.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 595.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
1 1
3 3
3.0 10.6 27.2 32.6 96.3 0.83 11
Silt (Phi + C)
4 4
6 6
7 7
8 8
9 9
10 10
11 11
12 12
13 13
13.0 60 4410.2 188.5 664662.9 25000 8.236
Concrete (rough)
14 14
14.0 60 4410.2 188.5 664662.9 25000 7.069 14.0 11.2 0.0 143.0 278.5 0.51 24
Pile Tip Stiff Clay
15 15
1000
900
800
Compression Load, Qdw -kN
700
600
500
400
300
200
100
0
0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 2.3 2.5 2.8 3.0 3.3 3.5 3.8 4.0 4.3 4.5 4.8 5.0
Settlement, X -cm
Total Side Tip
600 600
540 540
480 480
Compression Capacity, Qdw -kN
420 420
300 300
240 240
180 180
120 120
60 60
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
ILE PROFILES:
Pile Length, L= 14.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 595.00 -kN
Shear= 400.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.42000-cm
Max. Moment, M= 849.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
1 1
2 2
3 3
4 4
5 5
6 6
yt=0 at 6.4-m
St=0 at 0.1-m
7 7
8 8
9 9
10 10
11 11
12 12
13 13
14 14
Tip yt=-1.79E-4 Top yt=2.42E+0 Top Moment=-849.0 Top Shear=400.0
Max. yt=2.42E+0 Max. Moment=849.0 Max. Shear=407.1 Max. Pressure=51.67
Top St=0E+0
15 15
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.0 0.0 595.0 0.1 0.00 49.3
2 120.0 0.0 595.0 0.4 0.00 200.0
14 3 200.0 0.0 595.0 0.9 0.00 375.0 14
4 280.0 0.0 595.0 1.5 0.00 562.0
5 320.0 0.0 595.0 1.8 0.00 657.0
15 6 360.0 0.0 595.0 2.1 0.00 753.0 15
7 400.0 0.0 595.0 2.4 0.00 849.0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
13 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 13
1 40.0 0.0 595.0 0.1 0.00 49.3
2 120.0 0.0 595.0 0.4 0.00 200.0
14 3 200.0 0.0 595.0 0.9 0.00 375.0 14
4 280.0 0.0 595.0 1.5 0.00 562.0
5 320.0 0.0 595.0 1.8 0.00 657.0
15 6 360.0 0.0 595.0 2.1 0.00 753.0 15
7 400.0 0.0 595.0 2.4 0.00 849.0
400 400
360 360
320 320
280 280
240 240
Lateral Load, P -kN
160 160
120 120
80 80
40 40
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 90 180 270 360 450 540 630 720 810 900
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 1.8, 3.5, 5.3, 7.0, 8.8, 10.5, 12.3 -m
M= 0, P= 400.00 -kN
Results:
At Shear= 400.00-kN, Top Deflection, yt= 11.40000-cm
Stiffness Kpy= 35.09-kN/-cm
At Shear= 400.00-kN, Top Slope, St= -0.03020 Slope
Stiffness Kps= -13245.03-kN/Slope
Or St= -1.72980678 Degree, Stiffness Kps= -231.24-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00970-cm
Stiffness Kmy= 1030.93-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00010 Slope
Stiffness Kms= -96153.84-kN-m/Slope
Or St= -0.00595876 Degree, Stiffness Kms= -1678.20-kN-m/Degree
M= 0, P= 400.00 -kN
Results:
At Shear= 400.00-kN, Top Deflection, yt= 2.42000-cm
Stiffness Kpy= 165.29-kN/-cm
At Shear= 400.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
VERTICAL CAPACITY PILE CALCULATION Ø600mm-16m LONG
USING BH-1 DATA
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 87.44-kN *Soil Weight is not included
Side Resistance (Down)= 688.583-kN Side Resistance (Up)= 661.535-kN
Tip Resistance (Down)= 363.886-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 1052.470-kN Total Ultimate Capacity (Up)= 748.977-kN
Total Allowable Capacity (Down)= 640.999-kN Total Allowable Capacity (Up)= 418.210-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 640.00-kN Settlement= 0.11654-cm
At Xallow= 2.50-cm Qallow= 1025.34253-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
TOTAL LOADS:
Vertical Load, Q: 641.0 -kN
Load Factor for Vertical Loads: 1.0
Loads Supported by Pile Cap: 0 %
PILE PROFILE:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00 Batter Factor, Kbat= 1.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 641.00 -kN
____________________________________________
FACTOR OF SAFETY:
FSside FStip FSuplif FSweight
2.5 2 3 1
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
8 8
10 10
12 12
14 14
20 20
22 22
24 24
26 26
28 28
30 30
2000
1800
1600
Compression Load, Qdw -kN
1400
1200
1000
800
600
400
200
0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Settlement, X -cm
Total Side Tip
700 700
630 630
560 560
Compression Capacity, Qdw -kN
490 490
350 350
280 280
210 210
140 140
70 70
0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20
Foundation Depth, L -m Foundation Depth, L -m
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Profile:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.
PILE PROFILES:
Pile Length, L= 16.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0.00
SINGLE PILE:
Deduction factor due to Group Effect, R= 1.00
Vertical Load= 640.00 -kN
Shear= 405.00 -kN
Slope Restain, St= 0.00 -cm/-cm
Results:
Top Deflection, yt= 2.46000-cm
Max. Moment, M= 860.00-kN-m
Top Deflection Slope, St= 0.00000
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length)
The Max. Moment calculated by program is an internal moment of shaft due to the loading. Egineers
have to check whether the pile has enough moment capacity to resist the Max. Moment with adequate
factor of safety. If not, the pile may be damaged under the loading.
ALL-PILE Version 6 CivilTech Software www.civiltech.com Licensed to
Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Pressure -kN/m2 Depth (Zp)
from from
Pile Top-m -5.00 0 +5.00 -1000 0 +1000 -500 0 +500 -100 0 +100 Pile Top-m
0 0
2 2
4 4
6 yt=0 at 6.4-m 6
St=0 at 7.8-m
8 8
10 10
12 12
14 14
16 16
Tip yt=-4.6E-5 Top yt=2.46E+0 Top Moment=-860.0 Top Shear=405.0
Max. yt=2.46E+0 Max. Moment=860.0 Max. Shear=412.5 Max. Pressure=52.08
Top St=1.07E-17
18 18
20 20
22 22
24 24
26 26
28 28
30 30
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 40.5 0.0 640.0 0.1 0.00 49.9
2 122.0 0.0 640.0 0.4 0.00 203.0
28 3 202.0 0.0 640.0 0.9 0.00 380.0 28
4 284.0 0.0 640.0 1.5 0.00 569.0
5 324.0 0.0 640.0 1.8 0.00 666.0
30 6 364.0 0.0 640.0 2.1 0.00 762.0 30
7 405.0 0.0 640.0 2.5 0.00 860.0
2 2
4 4
6 6
8 8
10 10
12 12
14 14
16 16
18 18
20 20
22 22
24 24
Lateral Slope Vertical yt Slope Max.
No. Load Restraint Load at Top at Top Moment
26 (kN) (cm/cm) (kN) (cm) (cm/cm) (kN-m) 26
1 40.5 0.0 640.0 0.1 0.00 49.9
2 122.0 0.0 640.0 0.4 0.00 203.0
28 3 202.0 0.0 640.0 0.9 0.00 380.0 28
4 284.0 0.0 640.0 1.5 0.00 569.0
5 324.0 0.0 640.0 1.8 0.00 666.0
30 6 364.0 0.0 640.0 2.1 0.00 762.0 30
7 405.0 0.0 640.0 2.5 0.00 860.0
500 500
450 450
400 400
350 350
300 300
Lateral Load, P -kN
200 200
150 150
100 100
50 50
0 0
0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 0 90 180 270 360 450 540 630 720 810 900
Top Deflection, yt -cm Max. Moment in Single Pile, Mmax -kN-m
300
270
240
210
p, -kN/m
180
150
120
90
60
30
0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00
y, -m
Depth: 2.0, 4.0, 6.0, 8.0, 10.0, 12.0, 14.0 -m
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 11.60000-cm
Stiffness Kpy= 34.91-kN/-cm
At Shear= 405.00-kN, Top Slope, St= -0.03080 Slope
Stiffness Kps= -13149.35-kN/Slope
Or St= -1.76415229 Degree, Stiffness Kps= -229.57-kN/Degree
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00977-cm
Stiffness Kmy= 1023.54-kN-m/-cm
At Moment= 10.00-kN, Top Slope, St= -0.00010 Slope
Stiffness Kms= -96153.84-kN-m/Slope
Or St= -0.00595876 Degree, Stiffness Kms= -1678.20-kN-m/Degree
M= 0, P= 405.00 -kN
Results:
At Shear= 405.00-kN, Top Deflection, yt= 2.46000-cm
Stiffness Kpy= 164.63-kN/-cm
At Shear= 405.00-kN, Top Slope, St= 0.00000
Stiffness Kps= N/A
P= 0, M= 10.00 -kN-m
Results:
At Moment= 10.00-kN, Top Deflection, yt= 0.00000-cm
Stiffness Kmy= N/A
At Moment= 10.00-kN, Top Slope, St= 0.00000
Stiffness Kms= N/A
Notes:
Q - Vertical Load at pile top
P - Lateral Shear Load at pile top
M - Moment at pile top
Xall - Pile top total settlement
yt - Pile top deflection
St - Pile top deflection slope (deflection/unit length). Clockwise is negative
Kqx - Secant Stiffness: Vertical load vs. Vertical movement (settlement)
Kpy - Secant Stiffness: Lateral Shear vs. Lateral movement (deflection)
Kps - Secant Stiffness: Lateral Shear vs. Slope (rotation). Clockwise is negative
Kmy - Secant Stiffness: Moment vs. Lateral movement (deflection)
Kms - Secant Stiffness: Moment vs. Slope (rotation). Clockwise is negative
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.