Professional Documents
Culture Documents
DAMPER RATINGS
Pressure: Up to 5 in. wg - pressure differential
Channel Frame
Velocity: Up to 3,000 ft/min
Temperature: Up to 250 F
PRODUCT DETAILS
Frame Type: Channel
Frame Thickness: 16 ga
Material: Galvanized
Blade Type: 3V
1.25 in.
Blade Action: Opposed Height max
Blade Seal Material: N/A (typical)
Axle/Linkage Material: Steel
Axle Bearings: Synthetic
Damper Temp. Rating: 180 F
Jackshafting: No Preference
Actuator Sizing: Default SqFt Width
Ext. Shaft Length: Standard (6 in.) 5 in.
Multi-Section Fastening: Standard
Sizing: Nominal
• This drawing shows a general damper configuration and is not intended to depict the
ACTUATOR INFORMATION exact configuration of all dampers in this submittal.
• Width and height furnished approximately 0.250 in. undersize.
Actuator Type: 230 VAC • Factory supplied actuators are sized for 1,500 fpm and a fully-closed differential
Actuator Mounting: External pressure of 2 in. wc. Contact factory for actuator sizing on applications exceeding those
levels.
Actuator Location: Left Side • Installation instructions available at www.greenheck.com.
Operating Mode: TwoPosition
Actuator Operation: Spring Return
Fail Position: Closed
CODES APPROVED
IECC (International Energy Conservation Code)
NEMA Enclosure: Least Cost
compliant
Auxiliary Switches: No
The AMCA Certified Ratings Seal applies to Air
Spring Return Time: Standard
Performance
OPTIONS & ACCESSORIES
Union Label: No Preference
SUMMARY
ID # TAG QTY Width Height CONFIGURATION
Drive Arrangement:
Actuator Mfr: Actuator Model: Actuator Qty:
Drive-
Honeywell MS4609F1210 1
1-1 9 48.000 in. 48.000 in. CC-11-1FEL-0
Act. Orientation: Standoff:
Perp Down 1.500 in.
Drive Arrangement:
Actuator Mfr: Actuator Model: Actuator Qty:
Drive-
Honeywell MS4604F1210 1
1-2 1 59.000 in. 16.000 in. CC-21-1FEL-0
Act. Orientation: Standoff:
Perp Up 1.500 in.
Drive Arrangement:
Actuator Mfr: Actuator Model: Actuator Qty:
Drive-
Honeywell MS4604F1210 1
1-3 8 6.000 in. 6.000 in. CC-11-1FEL-0
Act. Orientation: Standoff:
Parallel 1.500 in.
AMCA
Greenheck Fan Corporation certifies that the model shown herein is licensed to bear the AMCA Seal. The ratings
shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the
requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance
ratings only.
DAMPER RATINGS
UL 555 Fire Resistance Rating
Fire Rating: 1 1/2 hours
Dynamic Closure Rating: Actual ratings are size dependent
Velocity: Up to 2,000 ft/min
Pressure: 6 in. wg
UL 555S Leakage Rating
Leakage Class: II
Operational Rating: Actual ratings are size dependent Height
Velocity: Up to 2,000 ft/min
Pressure: 6 in. wg
Temperature: Up to 350 F depending on actuator
Damper
SUMMARY
ID # TAG QTY Width Height CONFIGURATION
Compact Drive Arrangement:
Actuator Mounting: Actuator Location:
Configuration: Drive-
External Right Side
No MLS-11-1FER-1
Actuator Mfr: Actuator Model: Actuator Qty: Act. Orientation:
2-1 10 36.000 in. 36.000 in.
Honeywell MS4609F1210 1 Perp Up
Component
Sideplate Length: Damper Location: Mounting:
Location Code:
12.000 in. 6.188 in. Vertical
CL-1
Compact Drive Arrangement:
Actuator Mounting: Actuator Location:
Configuration: Drive-
External Right Side
No MLS-21-1FER-1
Actuator Mfr: Actuator Model: Actuator Qty: Act. Orientation:
2-2 8 46.000 in. 48.000 in.
Honeywell MS4620F1203 1 Perp Up
Component
Sideplate Length: Damper Location: Mounting:
Location Code:
12.000 in. 6.188 in. Vertical
CL-46
AMCA
Greenheck Fan Corporation certifies that the model shown herein is licensed to bear the AMCA Seal. The ratings
shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the
requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance
ratings only.
DAMPER RATINGS
Ratings
LeakageClass: II
Operational Ratings
Velocity: Up to 2,000 ft/min
Pressure: 6 in. wg
Temperature: Up to 350 F
Height
PRODUCT DETAILS
Frame Type: Channel
Frame Thickness: 16 ga
Damper
Blade Action: Parallel Width Location
Blade Seal: Silicone "A" 5 in.
Sideplate
Blade Indicator: None Length
Axle/Linkage Material: Steel
Axle Bearings: 316 SS • This drawing shows a general damper configuration and is not intended to depict the
Sizing: Nominal exact configuration of all dampers in this submittal.
• Width and height furnished approximately 0.250 in. undersize.
• Installation instructions available at www.greenheck.com.
ACTUATOR INFORMATION
Actuator Type: 230 VAC CODES APPROVED
Operating Mode: Two Position Model SMD-202 meets the requirements for smoke
Actuator Operation: Spring Return dampers established by:
Fail Position: Closed National Fire Protection Association:
Time Cycle: Standard NFPA Standards 90A, 92, 101, 105
Operating Temperature: 250 F IBC (International Building Codes)
Velocity: 2,000 ft/min CSFM (California State Fire Marshal)
Pressure: 4 in. wg Leakage (Smoke) Damper Listing (3230-0981:104)
NEMA Enclosure: 1 Underwriters Laboratories:
UL Classified to U.S. and Canadian safety standards
OPTIONS & ACCESSORIES Standard 555S (Listing # R13317)
Union Label: No Preference
SUMMARY
ID # TAG QTY Width Height CONFIGURATION
Compact Drive Arrangement:
Actuator Mounting: Actuator Location:
Configuration: Drive-
External Left Side
No MLS-21-1FEL-1
Actuator Mfr: Actuator Model: Actuator Qty: Act. Orientation:
3-1 2 40.000 in. 40.000 in.
Honeywell MS4620F1203 1 Perp Up
Component
Sideplate Length: Damper Location: Mounting:
Location Code:
12.000 in. 6.188 in. Vertical
CL-42
Compact Drive Arrangement:
Actuator Mounting: Actuator Location:
Configuration: Drive-
External Left Side
No MLS-21-1FEL-1
Actuator Mfr: Actuator Model: Actuator Qty: Act. Orientation:
3-2 2 42.000 in. 42.000 in.
Honeywell MS4620F1203 1 Perp Up
Component
Sideplate Length: Damper Location: Mounting:
Location Code:
12.000 in. 6.188 in. Vertical
CL-42
AMCA
Greenheck Fan Corporation certifies that the model shown herein is licensed to bear the AMCA Seal. The ratings
shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the
requirements of the AMCA Certified Ratings Programs. The AMCA Certified Ratings Seal applies to air performance
ratings only.
DAMPER RATINGS
Max. Pressure: 2 in. wg
Max. Velocity: Up to 2,000 ft/min
Temperature: 180 F
PRODUCT DETAILS
Frame: Galvanized
Frame Thickness: 16
Blade: Aluminum
Blade Seal Material: TPE
Blade Thickness: 0.063 in.
Axle Material: Plated Steel
Axle Bearings: Galvanized Ball
Start Open Pressure: 0.05 in. wg
Linkage Material: Galvanized Steel
Jamb Seal Material: None
Operation: Counterbalanced
Sizing: Nominal
SUMMARY
SECTIONS SECTIONS SHIP
ID # TAG QTY W (in.) H (in.)
WIDE HIGH SECTIONS
4-1 4 30.000 30.000 1 1 1
DAMPER RATINGS
Max. Pressure: Up to 2 in. wg - pressure differential
Max. Velocity: Up to 2,500 ft/min
Temperature: 180 F
PRODUCT DETAILS
Frame: Galvanized Steel
Frame Thickness: 18 ga
Blade: Aluminum
Blade Seal Material: Vinyl
Blade Thickness: 0.025 in. - 0.032 in.
Axle Material: Steel
Axle Bearings: Synthetic
Linkage Material: Galvanized
Actuator Voltage: None
Sizing: Nominal
SUMMARY
SECTIONS SECTIONS SHIP
ID # TAG QTY W (in.) H (in.)
WIDE HIGH SECTIONS
5-1 15 6.000 6.000 1 1 1
5-2 1 6.000 10.000 1 1 1
5-3 8 12.000 10.000 1 1 1
5-4 1 14.000 6.000 1 1 1
5-5 1 18.000 6.000 1 1 1
5-6 6 20.000 6.000 1 1 1
5-7 1 6.000 8.000 1 1 1
5-8 2 6.000 6.000 1 1 1
5-9 1 8.000 6.000 1 1 1
OPTIONS & ACCESSORIES • This drawing shows a general damper configuration and is not intended to depict the exact
configuration of all dampers in this submittal.
Transition: A • Damper is furnished approximately 0.250 in. undersize.
Union Label: No Preference • Installation instructions available at www.greenheck.com.
CODES APPROVED
This model meets the requirements for fire dampers established by:
• UL Classfied (U.S. and Canada)
Standard UL 555 (Listing #R13317)
• National Fire Protection Association
NFPA Standard 80,90A & 101
• IBC: International Building Codes
• California State Fire Marshal: CSFM listing # 3225-981:102
SUMMARY
ID # TAG QTY Width Height CONFIGURATION
Sections Wide: Sections High: Blade Stack: Mounting:
6-1 1 6.000 in. 10.000 in.
1 1 1.530 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-2 1 10.000 in. 12.000 in.
1 1 1.700 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-3 2 14.000 in. 6.000 in.
1 1 1.020 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-4 1 16.000 in. 8.000 in.
1 1 1.360 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-5 1 20.000 in. 8.000 in.
1 1 1.360 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-6 1 22.000 in. 47.000 in.
1 2 3.230 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-7 2 25.000 in. 25.000 in.
1 1 3.400 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-8 1 36.000 in. 12.000 in.
1 1 1.700 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-9 2 40.000 in. 16.000 in.
2 1 2.210 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-10 1 10.000 in. 20.000 in.
1 1 2.720 in. Vertical
Sections Wide: Sections High: Blade Stack: Mounting:
6-11 1 20.000 in. 12.000 in.
1 1 1.700 in. Vertical
Size Limitations
Minimum Maximum Size
WxH
Size Single Section Multiple Section
Inches 6x6 48 x 74 Unlimited
mm 152 x 152 1219 x 1880 Unlimited
Flange Options
5 in. 5 in. 5 in.
Notes:
• Low profile head and sill are used on sizes less than 17 in. (432mm) high
• Linkage concealed in the frame
• Electric actuator and manual quadrant available. Factory supplied actuators are sized for 1500 fpm (7m/s) and fully
closed differential pressure of 2 in. wg (.5 kPa). contact factory for actuator sizing on applications exceeding those
limits.
• Blades must be horizontal for either horizontal or vertical mount. If you need vertical blades, see VCD-23V model.
5D 6D
5D 6D
5D 6D
Figure 5.3
5D
D 4 (W) (H)
5D 3.14
5D
D 4 (W) (H)
3.14
D 4 (W) (H)
3.14
Figure 5.2
Figure 5.5
AMCA Certified Pressure Drop Data VCD-20
5D Greenheck
6D Fan Corporation certifies that the model VCD-
20 shown herein is licensed to bear the AMCA Seal. The
ratings shown are based on tests and procedures performed
in accordance with AMCA Publication 511 and comply with
the requirements of the AMCA Certified Ratings Programs.
The AMCA Certified Ratings Seal applies to Air Performance
ratings.
AMCA 5.2
5D
D 4 (W) (H)
3.14
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) Velocity (fpm) Velocity (fpm)
(in. wg) (in. wg) (in. wg)
500 0.01 500 0.01 500 0.01 500 0.01 500 0.01
1000 0.05 1000 0.03 1000 0.02 1000 0.04 1000 0.03
1500 0.11 1500 0.06 1500 0.05 1500 0.08 1500 0.07
2000 0.19 2000 0.10 2000 0.09 2000 0.15 2000 0.12
2500 0.29 2500 0.16 2500 0.14 2500 0.22 2500 0.18
3000 0.41 3000 0.23 3000 0.19 3000 0.32 3000 0.26
3500 0.55 3500 0.30 3500 0.27 3500 0.43 3500 0.36
4000 0.72 4000 0.40 4000 0.35 4000 0.56 4000 0.47
AMCA 5.3
5D 6D
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) Velocity (fpm) Velocity (fpm)
(in. wg) (in. wg) (in. wg)
5D
500 0.01 500 0.01 500 0.01 500 0.01 500 0.01
1000 0.03 1000 0.02 1000 0.02 1000 0.03 1000 0.03
1500 5D 0.08 6D 1500 0.04 D 41500
(W) (H) 0.03 1500 0.07 1500 0.06
2000 0.13 2000 0.07 3.14
2000 0.06 2000 0.12 2000 0.10
2500 0.20 2500 0.11 2500 0.09 2500 0.18 2500 0.16
3000 0.29 3000 0.16 3000 0.13 3000 0.26 3000 0.22
3500 0.40 3500 0.21 3500 0.19 3500 0.36 3500 0.30
4000 5D 0.51 4000 0.28 4000 0.25 4000 0.46 4000 0.39
D 4 (W) (H)
3.14
AMCA 5.5
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) Velocity (fpm) Velocity (fpm)
(in. wg) (in. wg) (in. wg)
500 0.03 500 0.03 500 0.03 500 0.03 500 0.03
1000 0.13 1000 0.12 1000 0.12 1000 0.12 1000 0.12
1500 0.30 1500 0.26 1500 0.28 1500 0.27 1500 0.28
2000 0.53 2000 0.47 2000 0.50 2000 0.47 2000 0.49
2500 0.82 2500 0.75 2500 0.78 2500 0.75 2500 0.77
3000 1.19 3000 1.04 3000 1.12 3000 1.07 3000 1.12
3500 1.62 3500 1.41 3500 1.53 3500 1.45 3500 1.53
4000 2.10 4000 1.90 4000 2.00 4000 1.91 4000 2.01
.4
St
.3
.2
Leakage testing was conducted in accordance with AMCA Standard 500-D and is expressed as cfm/ft2 of damper face
area. All data has been corrected to represent standard air at a(cfm/ft
Air Leakage density
2) of 0.075 lb/ft3 (1.204 kg/m3).
VCD-20
15.0
10.0
9.0
8.0
7.0
4.0
3.0
2.0
1.0
.9
.8
.7
.6
.5
.4
.3
.2
1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 70 80 90 100 150
Velocity Limitations
74
60
Damper Height (in.)
48
24
12
0
0 12 24 36 48
Damper Width (in.)
Space Envelopes VCD-20
Space Envelopes
On dampers less than 18 in. (457mm) high, actuators may also require clearances above and/or below the damper
frame. “B” and “T” dimensions are worst case clearance requirements for some dampers less than 18 in.
(457mm) high. All damper sizes under 18 in. (457mm) high do not require these worst case clearances. If space
availability above or below the damper is limited, each damper size should be individually evaluated.
D
T
Damper
frame
Optional
Jackshaft
Height T B D
Actuator Type/Model
Inches (mm) Inches (mm)
>6 to <10 0 123⁄4 6
AFBUP (-S) and FSNF Series, Belimo
>10 to <18 0 2 6
MSxx20 Series, Honeywell
>18 0 0 10
>6 to <10 0 31⁄2 6
FSLF, LF and TFB Series, Belimo
>10 0 0 6
>6 to <9 0 43⁄4 6
MSxx04 & MSxx09 Series, Honeywell
>9 0 0 6
>6 to <10 0 12 ⁄43
6
MS75xx Series, Honeywell >10 to <18 0 7 6
>18 0 0 6
This drawing depicts the worse case clearance requirements for an actuator with a jackshaft.
1 1/4 in. (32mm)
max.
Actuator
Mounting
• External - includes extension pin (standoff bracket
optional) C
Multi-Section Assembly
Dampers larger than the maximum single section size, will be made up of a multiple of equal size sections. Multiple
section dampers can be jackshafted together so that all sections operate together as shown below.
NOTE: Dampers larger than 48 in. x 74 in.
(1219mm x 1880mm) are not intended to be structurally self supporting. Additional horizontal bracing is
recommended to support the weight of the damper and vertical bracing should be installed as required to hold
against system pressure.
Specifications
Control dampers meeting the following specifications shall be furnished and installed where shown on plans and/or as
described in schedules.
Damper blades shall be 16 ga. (1.5mm) galvanized steel 3V type with three longitudinal grooves for reinforcement.
Blades shall be completely symmetrical relative to their axle pivot point, presenting identical resistance to airflow and
operation in either direction through the damper (blades that are non-symmetrical relative to their axle pivot point or
utilize blade stops larger than 1⁄2 in. [13mm] are unacceptable). Linkage shall be blade-to-blade concealed in jamb (out of
the airstream) to protect linkage and reduce pressure drop and noise.
Damper frame shall be 16 ga. (1.5mm) galvanized steel formed into a structural hat channel shape with reinforced
corners to meet 11 ga. (3.1mm) criteria. Bearings shall be corrosion resistant, permanently lubricated, synthetic (acetal)
sleeve type, rotating in extruded holes in the damper frame for maximum service. Axles shall be square and positively
locked into the damper blade.
The Damper manufacturer’s submittal data shall certify all air performance pressure drop data is licensed in accordance
with the AMCA Certified Ratings Program for Test Figures 5.2, 5.3 and 5.5. Damper air performance data shall be
developed in accordance with the latest edition of AMCA Standard 500-D.
Basis of design is model VCD-20.
22-2FEL- 2
1 2 3 4 5 6 7
1 Number of sections wide
Damper Height
3 Number of actuators or manual quadrants
7 Number of jackshafts
Vertical blade and face & bypass dampers are given a configuration ID number that helps describe the
construction of the damper. See the following examples:
Jump-over Jackshaft
C
1
2
4
Model FSD-212
Combination Fire Smoke Damper
Application
Steel 3V Blades
Model FSD-212 is a combination fire smoke damper with
3V style blades. This model is designed for operation UL 555S Leakage Class II
and dynamic closure in emergency fire smoke situations. UL 555 1 ⁄2 Hour Fire Resistance Rating
1
It is rated for airflow and leakage in either direction. The
FSD-212 may be installed vertically (with blades running
horizontal) or horizontally.
Ratings
UL 555 Fire Resistance Rating
Fire Rating: 11⁄2 hours
Dynamic Closure Rating: Actual ratings are size
dependent
Velocity: Up to 2,000 fpm (10.2 m/s)
Pressure: Up to 6 in. wg (1.5 kPa)
UL 555S Leakage Rating
Leakage Class: II
Operational Rating: Actual ratings are size
dependent
Velocity: Up to 2,000 fpm (10.2 m/s)
Pressure: Up to 6 in. wg (1.5 kPa)
Width and Height dimensions furnished approximately 1⁄4 in.
Temperature: Up to 350°F (177°C) - depending (6mm) undersize. Add sleeve thickness for overall sleeved
upon the actuator damper dimension.
5D 6D
5D 6D
Figure 5.3 5D 6D
5D
D 4 (W) (H)
5D 3.14
5D
D 4 (W) (H)
3.14
D 4 (W) (H)
3.14
Figure 5.2
Figure 5.5
Pressure Drop FSD-212
AMCA Figure 5.2 5D
D 4 (W) (H)
3.14
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg)
500 0.04 500 0.02 500 0.01 500 0.01 500 0.03
1000 0.14 1000 0.07 1000 0.04 1000 0.06 1000 0.10
1500 0.31 1500 0.16 1500 0.09 1500 0.13 1500 0.23
2000 0.55 2000 0.29 2000 0.16 2000 0.23 2000 0.41
2500 0.86 2500 0.45 2500 0.25 2500 0.36 2500 0.63
3000 1.24 3000 0.65 3000 0.36 3000 0.52 3000 0.91
3500 1.69 3500 0.89 3500 0.49 3500 0.70 3500 1.24
4000 2.20 4000 1.16 4000 0.64 4000 0.92 4000 1.62
5D 6D
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) 5D Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg)
500 0.02 500 0.01 500 0.01 500 0.01 500 0.02
1000 0.09 1000 0.04 1000 0.03 1000 0.04 1000 0.07
1500 0.20 1500 0.09 1500 0.06 D 1500 4 (W) (H)0.10 1500 0.16
2000 0.36 2000 0.16 5D 2000 0.11 2000 3.14 0.17 2000 0.29
2500 0.56 2500 0.25 2500 0.17 2500 0.27 2500 0.45
3000 0.81 3000 0.35 3000 0.24 3000 0.39 3000 0.64
3500 1.10 3500 0.48 3500 0.33 3500
4 (W) (H) 0.53 3500 0.88
4000 1.44 4000 0.63 4000 0.42
D 4000 0.70 4000 1.14
3.14
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg)
500 0.06 500 0.03 500 0.03 500 0.03 500 0.04
1000 0.22 1000 0.14 1000 0.12 1000 0.13 1000 0.17
1500 0.50 1500 0.31 1500 0.26 1500 0.30 1500 0.38
2000 0.89 2000 0.54 2000 0.46 2000 0.53 2000 0.67
2500 1.39 2500 0.85 2500 0.73 2500 0.83 2500 1.04
3000 2.00 3000 1.22 3000 1.05 3000 1.19 3000 1.50
3500 2.72 3500 1.66 3500 1.42 3500 1.62 3500 2.05
4000 3.55 4000 2.17 4000 1.86 4000 2.11 4000 2.67
T*
Space Envelopes
S
Externally mounted actuators always require space
outside of the damper sleeve. The “S” dimension
illustrates the clearance required for various
available actuators.
On dampers less than 18 in. (457mm) high,
actuators may also require clearances above and/
or below the sleeve. “B” and “T” dimensions are
worst case clearance requirements for some
dampers less than 18 in. (457 mm) high. All
dampers 18 in. (457mm) or more in height, do
not require these worst case clearances. If space
availability above or below the damper sleeve is
limited, each damper size should be individually
evaluated. B*
B*
B* T* S
With With Piggyback
Actuator Type/Model
RRL, RRL/OCI, or RRL, RRL/OCI, or
No Yes
TOR TOR
120 Volt AC
FSLF120 (-S) Belimo 7 ⁄16 in (195mm)
11
0 6 in. (152mm) NA
FSNF120 (-S) Belimo 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
FSTF120 (-S) Belimo 711⁄16 in (195mm) 0 6 in. (152mm) NA
MS4104 Series Honeywell 1
⁄2 in. (13mm) 8 ⁄2 in (216mm)
1
6 in. (152mm) NA
MS4X09 Series Honeywell 1
⁄2 in. (13mm) 81⁄2 in (216mm) 6 in. (152mm) NA
MS4120 Series Honeywell 1
⁄2 in. (13mm) 9 ⁄16 in (249mm)
13
6 in. (152mm) 9 in. (229mm)
24 Volt AC
FSAF24 (-S) Belimo 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) NA
FSTF24 (-S) Belimo 7 ⁄16 in (195mm)
11 1
⁄2 in. (13mm) 6 in. (152mm) NA
FSLF24-S Belimo 711⁄16 in (195mm) 0 6 in. (152mm) NA
FSNF24 (-S) Belimo 1
⁄2 in. (13mm) 9 ⁄16 in (249mm)
13
6 in. (152mm) 9 in. (229mm)
MS8104 Series Honeywell 1
⁄2 in. (13mm) 81⁄2 in (216mm) 6 in. (152mm) NA
MS8120 Series Honeywell 1
⁄2 in. (13mm) 9 ⁄16 in (249mm)
13
6 in. (152mm) 9 in. (229m)
230 Volt AC
FSLF230-S Belimo 711⁄16 in (195mm) 0 6 in. (152mm) NA
FSNF230-S Belimo 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
FSTF230-S Belimo 711⁄16 in (195mm) 1
⁄2 in. (13mm) 6 in. (152mm) NA
MS4604 Series Honeywell 1
⁄2 in. (13mm) 8 ⁄2 in (216mm)
1
6 in. (152mm) NA
MS4X09 Series Honeywell 1
⁄2 in. (13mm) 81⁄2 in (216mm) 6 in. (152mm) NA
MS4620 Series Honeywell 1
⁄2 in. (13mm) 9 ⁄16 in (249mm)
13
6 in. (152mm) 9 in. (229mm)
* For dampers 18 in. (457mm) or more in height these dimensions are 0 in.
Application Data FSD-212
Damper Sleeve Dimensional Data
The drawings below and corresponding table show the position of the FSD-212 damper when mounted in a factory
sleeve. The standard mounting locations provide enough space for the mounting of actuators, controls and allow space
for installation of retaining angles and duct connections.
The standard location of a damper mounted in a factory sleeve ("A" dimension) is shown below. The damper can be
positioned at other locations within a range of 6 in. (152mm) to 16 in. (406mm) for the "A" dimension.
Sleeve 1½ in. (38mm)
maximum blade
clearance "A" Dimension
in. (mm)
Sleeve Std Sleeve Max Sideplate
Sleeve
3¾ in.
(95mm)
All Dampers (RRL) 7 ⁄16 in. (183)
3
16 (406) 63⁄16 (157)
When Height is 11 in.
5³/8 in.
(279) or less with RRL, 12 (305) 16 (406) 12 (305)
(137mm) RRL/OCI, or TOR
Varies due to
height NOTE: Entire damper frame is not required to be installed within the wall. The damper
blades, when closed should be contained within the wall.
11/2 in. max.
Sideplate
5 in.
A (127mm)
Sleeve Length
3 3/4 in.
6 in.
Varies
5 3/8 in.
5 in.
A 5 in.
A
Sideplate
Length** Sleeve Length
Double Section
Single Section
50 in.
(1270mm)
50 in. 50 in.
(1270mm) (1270mm)
32 in. (813mm)
64 in. (1626mm)
32 in. (813mm)
Transitioned Damper Dimensions FSD-212
When a combination fire smoke damper is being used in conjunction with round or oval ductwork, the FSD-212 can be
supplied in a factory sleeve with round or oval transitions on both ends of the sleeve. Dampers should be ordered to the
duct dimensions. Drawings below show overall damper size.
D* + 2 in. (51mm) +T s
W* + 2 in. (51mm)+Ts
W* + 2 in. (51mm)+Ts
D* + 2 in. (51mm)+Ts
H* + 2 in. (51mm)+T s H* + 2 in. (51mm)+Ts
2 1/8 in. H*
2 1/8 in. H* (54mm)
2 1/8 in. (54mm)
(54mm)
W*
W*
16 in. D* 16 in. 16 in.
(406mm) (406mm) (406mm)
Minimum Minimum Minimum
Specifications
Combination Fire Smoke Dampers meeting the following in the damper frame. Blade edge seals shall be silicone
specifications shall be furnished and installed where rubber designed to inflate and provide a tighter seal
shown on plans and/or as described in schedules. against leakage as pressure on either side of the damper
Dampers shall meet the requirements of NFPA 80, increases. Jamb seals shall be stainless steel compression
90A, 92, 101 & 105 and further shall be tested, rated type. Blades shall be symmetrical relative to their axle
and labeled in accordance with the latest edition of UL pivot point, presenting identical resistance to airflow in
Standards 555 and 555S. Dampers shall have a UL555 either direction or pressure on either side of the damper.
fire rating of 1½ hours and be of low leakage design The Damper Manufacturer's submittal data shall certify
qualified to UL 555S Leakage Class II. all air performance pressure drop data is licensed in
Each damper /actuator combination shall have a UL555S accordance with the AMCA Certified Ratings Program for
elevated temperature rating of 250°F (121°C) minimum Test Figures 5.2, 5.3, and 5.5. Damper air performance
and shall be operational and dynamic rated to operate data shall be developed in accordance with the latest
at maximum design air flow at its installed location. Each edition of AMCA Standard 500-D. Dampers shall be
damper shall be supplied with an appropriate actuator labeled with the AMCA Air Performance Seal.
installed by the damper manufacturer at the time of Damper must be rated for mounting vertically (with blades
damper fabrication. Damper actuator shall be (specifier running horizontal) or horizontally and be UL 555S rated
select one of the following) electric type for 120, 24, or for leakage and airflow in either direction through the
230 volt operation. damper. Each damper shall be supplied with a 165°F
Damper blades shall be 16 ga. (1.5mm) galvanized steel (74°C) RRL.
3V type with three longitudinal grooves for reinforcement. The basis of design is Model FSD-212.
Damper frame shall be galvanized steel formed into a
structural hat channel shape with reinforced corners.
Bearings shall be 316SS type rotating in extruded holes
Construction Standard
Frame Material Galvanized steel
Frame Material Thickness 16 ga. (1.5mm) LH
Features:
• Frames are constructed with reinforced corners. Low
profile head and sill are used on sizes less than 17 in.
high (432mm).
• Blades are reinforced with 3 longitudinal structurally
designed vee's.
• Actuators: Electric Installation instruction available at www.greenheck.com
Options & Pressure Drop Data SMD-202
Options for SMD-202:
• Factory mounted accessories • Sealed transitions and sleeves
- Quick connect breakaway connections
- Access doors • Security bars
• Test switches (GTS-3 & GTS-4) • Smoke detectors
• Momentary test switch • Transitions: R, C, O
• POC retaining angles
• OCI (Open closed indication switches)
5D 6D
AMCA 5.3
5D
D 4 (W) (H)
3.14
AMCA 5.2
AMCA 5.5
Pressure Drop SMD-202
AMCA Figure 5.2 5D
D 4 (W) (H)
3.14
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg)
500 0.04 500 0.02 500 0.01 500 0.01 500 0.03
1000 0.14 1000 0.07 1000 0.04 1000 0.06 1000 0.10
1500 0.31 1500 0.16 1500 0.09 1500 0.13 1500 0.23
2000 0.55 2000 0.29 2000 0.16 2000 0.23 2000 0.41
2500 0.86 2500 0.45 2500 0.25 2500 0.36 2500 0.63
3000 1.24 3000 0.65 3000 0.36 3000 0.52 3000 0.91
3500 1.69 3500 0.89 3500 0.49 3500 0.70 3500 1.24
4000 2.20 4000 1.16 4000 0.64 4000 0.92 4000 1.62
5D 6D
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) 5D Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg)
500 0.02 500 0.01 500 0.01 500 0.01 500 0.02
1000 0.09 1000 0.04 1000 0.03 1000 0.04 1000 0.07
1500 0.20 1500 0.09 1500 0.06 D 1500 4 (W) (H)0.10 1500 0.16
5D
2000 0.36 2000 0.16 2000 0.11 2000 3.14 0.17 2000 0.29
2500 0.56 2500 0.25 2500 0.17 2500 0.27 2500 0.45
3000 0.81 3000 0.35 3000 0.24 3000 0.39 3000 0.64
3500 1.10 3500 0.48 3500 0.33 D 4 (W)
3500 (H) 0.53 3500 0.88
4000 1.44 4000 0.63 4000 0.42 3.14
4000 0.70 4000 1.14
12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm)
Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop
Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg)
500 0.06 500 0.03 500 0.03 500 0.03 500 0.04
1000 0.22 1000 0.14 1000 0.12 1000 0.13 1000 0.17
1500 0.50 1500 0.31 1500 0.26 1500 0.30 1500 0.38
2000 0.89 2000 0.54 2000 0.46 2000 0.53 2000 0.67
2500 1.39 2500 0.85 2500 0.73 2500 0.83 2500 1.04
3000 2.00 3000 1.22 3000 1.05 3000 1.19 3000 1.50
3500 2.72 3500 1.66 3500 1.42 3500 1.62 3500 2.05
4000 3.55 4000 2.17 4000 1.86 4000 2.11 4000 2.67
S
Externally mounted actuators always require space
outside of the damper sleeve. The “S” dimension
illustrates the clearance required for various available
actuators.
On dampers less than 18 in. (457mm) high, actuators
may also require clearances above and/or below the
sleeve. “B” and “T” dimensions are worst case clearance
requirements for some dampers less than 18 in. (457mm)
high. All dampers 18 in. (457mm) or more in height,
do not require these worst case clearances. If space
availability above or below the damper sleeve is limited,
each damper size should be individually evaluated.
B*
B*
B* T* S
With With Piggyback
Actuator Type/Model
RRL, RRL/OCI, or RRL, RRL/OCI, or
No Yes
TOR TOR
120 Volt AC
FSLF120 (-S) Belimo 711⁄16 in (195mm) 0 6 in. (152mm) NA
FSNF120 (-S) Belimo 1
⁄2 in. (13mm) 9 ⁄16 in (249mm)
13
6 in. (152mm) 9 in. (229mm)
FSTF120 (-S) Belimo 711⁄16 in (195mm) 0 6 in. (152mm) NA
MS4X09 Series Honeywell 1
⁄2 in. (13mm) 8 ⁄2 in (216mm)
1
6 in. (152mm) NA
MS4120 Series Honeywell 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
24 Volt AC
FSAF24 (-S) Belimo 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) NA
FSTF24 (-S) Belimo 711⁄16 in (195mm) 1
⁄2 in. (13mm) 6 in. (152mm) NA
FSLF24-S Belimo 7 ⁄16 in (195mm)
11
0 6 in. (152mm) NA
FSNF24 (-S) Belimo 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
MS8120 Series Honeywell 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
230 Volt AC
FSLF230-S Belimo 711⁄16 in (195mm) 0 6 in. (152mm) NA
FSNF230-S Belimo 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
FSTF230-S Belimo 711⁄16 in (195mm) 1
⁄2 in. (13mm) 6 in. (152mm) NA
MS4X09 Series Honeywell 1
⁄2 in. (13mm) 8 ⁄2 in (216mm)
1
6 in. (152mm) NA
MS4620 Series Honeywell 1
⁄2 in. (13mm) 913⁄16 in (249mm) 6 in. (152mm) 9 in. (229mm)
* For dampers 18 in. (457mm) or more in height these dimensions are 0 in.
Application Data SMD-202
Sleeve 1½ in. (38mm)
A
When Height is Sideplate
12 Length**
NOTE: Entire damper frame is not required to be installed within the wall.
Double Section
Single Section
50 in.
(1270mm)
50 in. 50 in.
(1270mm) (1270mm)
32 in. (813mm)
64 in. (1626mm)
32 in. (813mm) 32 in. (813
100 in.
(2540mm)
Transitioned Damper Dimensions SMD-202
When a fire/smoke damper is being used in conjunction with round or oval ductwork, the SMD-202 can be supplied
in a factory sleeve with round or oval transitions on both ends of the sleeve. Dampers should be ordered to the duct
dimensions. Drawings below show overall damper size.
D* + 2 in. (51mm) +T s
W* + 2 in. (51mm)+Ts
W* + 2 in. (51mm)+Ts
D* + 2 in. (51mm)+Ts
H* + 2 in. (51mm)+T s H* + 2 in. (51mm)+Ts
2 1/8 in. H*
2 1/8 in. H* (54mm)
2 1/8 in. (54mm)
(54mm)
W*
W*
16 in. D* 16 in. 16 in.
(406mm) (406mm) (406mm)
Minimum Minimum Minimum
Ts = (2)(Sleeve Thickness)
Specifications
Smoke Dampers meeting the following specifications shall be stainless steel compression type. Blades shall be symmetrical relative
furnished and installed where shown on plans and/or as described in to their axle pivot point, presenting identical resistance to airflow in
schedules. Dampers shall meet the requirements of NFPA 92, 101 & either direction or pressure on either side of the damper.
105 and further shall be tested, rated and labeled in accordance with The Damper Manufacturer's submittal data shall certify all air
the latest edition of UL Standards 555S. Dampers shall have a low performance pressure drop data is licensed in accordance with the
leakage design qualified to UL555S Leakage Class II. AMCA Certified Ratings Program for Test Figures 5.2, 5.3, and 5.5.
Each damper /actuator combination shall have a UL555S elevated Damper air performance data shall be developed in accordance with
temperature rating of 250°F (121°C) minimum and shall be rated to the latest edition of AMCA Standard 500-D. Dampers shall be labeled
operate at maximum design air flow at its installed location. Each with the AMCA Air Performance Seal.
damper shall be supplied with an appropriate actuator installed by Damper must be rated for mounting vertically (with blades running
the damper manufacturer at the time of damper fabrication. Damper horizontal) or horizontally and be UL 555S rated for leakage and airflow
actuator shall be (specifier select one of the following) electric type for in either direction through the damper.
120 (24 or 230) Volt operation.
The basis of design is model SMD-202.
Damper blades shall be 16 ga. (1.5mm) galvanized steel 3V type with
three longitudinal grooves for reinforcement. Damper frame shall
be galvanized steel formed into a structural hat channel shape with
reinforced corners. Bearings shall be 316SS type rotating in extruded
holes in the damper frame. Blade edge seals shall be silicone rubber
designed to inflate and provide a tighter seal against leakage as
pressure on either side of the damper increases. Jamb seals shall be
5.5 5.5
1.0 1.0
.9 .9
.8 .8
5.2 5.2
.7 .7
.6 .6
.5 .5
5.3 5.3
Pressure Drop (in. wg)
.3 .3
.2 .2
.1 .1
.09 .09
.08 .08
.07 .07
.06 .06
.05 .05
.04 .04
.03 .03
100 200 300 400 500 600 800 1000 2000 3000 100 200 300 400 500 600 800 1000 2000 3000
700 900 700 900
Velocity Velocity
(fpm) (fpm)
Specifications
Barometric backdraft dampers meeting the following linkage with blade mounted counterbalance weights.
specifications shall be furnished and installed where shown Damper manufacturer’s printed application and
on plans and/or as described in schedules. performance data including pressure, velocity, and
Dampers shall consist of: 16 ga. (1.5mm) insert mount temperature limitations shall be submitted for approval
galvanized steel hat channel frame with 5 in. (127mm) showing damper suitable for pressures to 2 in. wg (0.5
depth; blades from 0.063 in. (1.6mm) thick formed kPa), velocities to 2000 fpm (10.2 m/s, and temperatures
aluminum, eccentrically pivoted; 3⁄8 in. (9.5mm) square to 180°F (82°C). Testing and ratings to be in accordance
plated steel axles with galvanized steel press-fit ball with AMCA Standard 500-D.
bearings; damper shall be equipped with pressure activated Basis of design is model BR-30.
TPE blade seals; and internal plated steel blade-to-blade
Application
Model DFD-150 is approved for use in walls, floors, and partitions
with fire resistance ratings less than 3 hours. This model carries a
11⁄2 hour UL fire damper label. UL555 classifies dynamic rated fire
damper for use in HVAC systems that are operational in the event
of fire.
Ratings
UL 555 Fire Resistance
Fire Rating: 11⁄2 hours
Velocity
4000 fpm (20.3 m/s) vertical mount only, up to 24 in. x 24 in.
(610mm x 610mm);
2000 fpm (10.2 m/s) vertical or horizontal mount all sizes
Pressure
Maximum: 4 in. wg (1 kPa)
W*
W*
Stainless Steel Fusible Link (replaceable)
Closure Spring Stainless Steel Fusible Link (replaceable)
Closure Spring
H*
H*
“K” side
“K” side
Horizontal Mount
Horizontal Mount
Document Links
Installation Instructions Life Safety Damper Catalog
Damper Warranty
Sleeve
Damper
H*
K
Damper CL Damper Frame
Location W*
L
Overall Sleeve Length
Sealed Option
When sealed option is selected, B transition will need to be field sealed in the area where duct to sleeve connection is made.
Size Limitations
Inches Type A Type B & B2 P
(mm) Minimum Maximum* Minimum Maximum*
Single H*
H *
4x4 36 x 36 4x3 36 x 31
Section
(102 x102) (914 x 914) (102 x 76) (914 x 787)
Vertical
VERTICAL MOUNT
72 x 48 72 x 45 HORZONTAL MOUNT
(1829 x 1219), (1829 x 1143),
Multi
60 x 60 60 x 56 1 1/2
Varies
1 1/2
Section** NA NA in.
3 in.
W* in.
W *
(1524 x 1524) or (1524 x 1422) or
Vertical
120 x 30 O* 120 x 26
H*
(3048 x 762) (3048 x 660) Type A
16 in.
10 in.
Single
4x4 30 x 30 4x3 30 x 26
Section
(102 x 102) (762 x 762) (102 x 76) (762 x 660)
Horizontal
Multi
3 in.
NA 48 x 36 48 x 33
Section** NA
W* (1219 x 914) (1219 x 838) Damper
Horizontal Location
K Dim.
Sleeve
* Sizes are based on 165°F closure temperature and 2000 fpm. Consult
Length
factory for maximum size for different temperatures and velocities. Varies
** Consult factory for number of sections. Type B2
Multi-Section Limitations - Type A
Maximum Single Section
Dimensions
Maximum damper height is 48 in. (1219mm) when combination width is
Maximum Single Section Dimensions 72 in. (1829mm) or less.
36 in.
(914mm)
36 in. (914mm) max. max.
Maximum
Type A Single Single
SectionSection
Dimensions 72 in.
(1829mm) max.
31 in.(787mm)
Max.
Multi-Section Limitations
Maximum damper height is 48 in. (1219mm) when combination width is 48 in. (1219mm) or less.
45 in. (1143mm)
36 in. Max.
(914mm)
max.
48 in.
72 in.
(1219mm) (1829mm)
max. Max.
H* O* H* O*
3 (76) 5 (127) 30 (762) 34 (864)
O*
4 (102) 6 (152) 31 (787) 36 (914) H*
* Dimension is inches (mm). These dimensions are furnished approximately 1⁄4 in. (6mm) undersize. All ‘H’ dimensions larger than single section height
are two sections high. Refer to size limitations chart. The top section is a Type B/B2 and the bottom section are Type A.
70 x 44 (1778 x 1118),
Multi Section 55
NA NA 58 x 55 (1473 x 1397) or NA 58 (1473)
Vertical** (1397)
118 x 25 (2997 x 635)
Single Section
3 (76) 25 (635) 3 x 3 (76 x 76) 28 x 25 (711 x 635) 3 (76) 28 (711)
Horizontal
Multi Section
NA 32 (813) NA 46 x 32 (1163 x 787) NA 34 (864)
Horizontal**
+
With 2 in. (51mm) offset. Sizes adjust with an 1 in. (25mm) offset.
* Sizes are based on 165°F closure temperature and 2000 fpm. Consult factory for maximum size for different temperatures and velocities.
** Consult factory for number of sections.
Type CR
30in.
30 in. O*
(762mm)
max. (762mm)
max.
34 in. 34 in. D*
(864mm) (864mm)
max. max.
W*+2
Type CO
Type CR Type R O*
H*
W*
W*+2
34 in.
Type C
(889mm)
30 in. max.
(762mm) O*
max. Type R transition is centered on
damper frame. (Dimension are with H*
2 in. (51mm) offset.)
W*
C, CO, CR transitions are positioned 1 in. (25mm)
from bottom of sleeve.
H* or D* O* H* or D* O* H* or D* O* H* or D* O* H* or D* O*
3 (76) 6 (152) 21 (533) 26 (660) 39 (991) 45 (1143) 3 (76) 6 (152) 18 (457) 22 (559)
4 (102) 7 (178) 22 (559) 27 (686) 40 (1016) 46 (1168) 4 (102) 7 (178) 19 (483) 23 (584)
5 (127) 8 (203) 23 (584) 28 (711) 41 (1041) 47 (1194) 5 (127) 8 (203) 20 (508) 24 (610)
6 (152) 9 (229) 24 (610) 29 (737) 42 (1067) 48 (1219) 6 (152) 9 (229) 21 (533) 26 (660)
7 (178) 10 (254) 25 (635) 30 (762) 43 (1092) 49 (1245) 7 (178) 10 (254) 22 (559) 27 (686)
8 (203) 11 (279) 26 (660) 31 (787) 44 (1118) 50 (1270) 8 (203) 11 (279) 23 (584) 28 (711)
9 (229) 12 (305) 27 (686) 32 (813) 45 (1143) 50 (1270) 9 (229) 12 (305) 24 (610) 29 (737)
10 (254) 13 (330) 28 (711) 33 (838) 46 (1168) 51 (1295) 10 (254) 13 (330) 25 (635) 30 (762)
11 (279) 14 (356) 29 (737) 34 (864) 47 (1194) 52 (1321) 11 (279) 14 (356) 26 (660) 31 (787)
12 (305) 15 (381) 30 (762) 36 (914) 48 (1219) 53 (1346) 12 (305) 15 (381) 27 (686) 31 (787)
13 (330) 16 (406) 31 (787) 37 (940) 49 (1245) 54 (1372) 13 (330) 16 (406) 28 (711) 32 (813)
14 (356) 18 (457) 32 (813) 37 (940) 50 (1270) 55 (1397) 14 (356) 18 (457) 29 (737) 33 (838)
15 (381) 19 (483) 33 (838) 39 (991) 51 (1295) 56 (1422) 15 (381) 19 (483) 30 (762) 34 (864)
16 (406) 20 (508) 34 (864) 40 (1016) 52 (1321) 57 (1448) 16 (406) 20 (508) 31 (787) 35 (889)
17 (432) 21 (533) 35 (889) 41 (1041) 53 (1346) 58 (1473) 17 (432) 21 (533) 32 (813) 36 (914)
18 (457) 22 (559) 36 (914) 42 (1067) 54 (1372) 59 (1499)
19 (483) 23 (584) 37 (940 43 (1092) 55 (1397) 60 (1524)
20 (508) 24 (610) 38 (965) 44 (1118) -
* Dimension is inches (mm). These dimensions are furnished approximately 1/4 in. (6mm) undersize. All ‘H’ dimensions larger than single section height
are two sections high. Refer to size limitations chart.