Professional Documents
Culture Documents
CONSULTING ENGINEERS
2480 VANTAGE DRIVE COLORADO SPRINGS, CO 80919
(719)598-7666 FAX (719)598-0258
Per your request, we have completed an analysis of the above referenced panels. The
panels, with the structural properties indicated in this report, is certified to meet or exceed
the requirements of the following design specifications:
Panel cross-section
Panel analysis, pages 1 to 183
Panel Span Load tables, pages S 1 to S71
Panels widths greater than 14 inches exceed the AISI allowable ratios for the panel width
element. The AISI specifications, Section B 1.1(a) states:
". ..stiffened elements having w/t ratios larger than 500 can be used with adequate
design strength to sustain the required loads; however; substantial deformations of
such elements usually will invalidate the design equations of this specification."
Before using the enclosed panel span tables, you will need to review the analysis reports
for each panel. It is our opinion that the panels with wlt ratio elements exceeding 500
should be verified by testing before using the respective panel span tables.
Please note that the panel analysis and Load Tables have been evaluated based on the
assumption that the proper bearing, side laps, end laps, bracing, anchorage and structural
supports are being utilized in the member's installation. We do not certifL the installation
method, attachment and supporting materials.
Sincerely,
President
PAGE NO. 73
DATE: 04-20-1999
John F. B u t t s & A s s o c i a t e s , I n c .
2480 Vantage D r i v e
Colorado S p r i n g s , CO 80919
(719) 598-7666
P e r AISI Cold-Formed S t e e l
Design Manual, 1996 E d i t i o n
DIMENSIONS
P a n e l s o t t o m Width = 11.872 i n
P a n e l O v e r a l l Width = 12.000 i n
P a n e l O v e r a l l Height= 2.000 i n
SPECIAL CONDITIONS
Seam R o t a t i o n : 90 deg.
Gross S e c t i o n P r o p e r t i e s
Effective properties
End B e a r i n g
Ix Sx IY SY Mnx MnY Vnx Pne Pnei
(in4) (in3) (in4) (in3) (in-k) (in-k) (kip) (kip) (k/in)
Torsional Properties
Xo Ro Beta Cw Jv*1000 Fy Fu E G
(in) (in) (in6) (in4) ( k s i ) ( k s i ) (ksi) (ksi)
ELEMENT L Y LY LYY 10
PAGE NO. 7 6
DATE: 04-20-1999
ELEMENT L Y LY LYY I0
New T e c h SS210-A P a n e l
..............................................................................
DEFLECTION
ELEMENT L Y LY LYY 10
ELEMENT L Y LY LYY I0
ELEMENT L Y LY LYY 10
N/t= 83.33
k = 1.515
Cl = 0.887
C2 = 0.960
C3 = 0.830
C4 = 0.900
C9 = 1.000
CO = 1.000 - Element 2, 22
Pend= t^2*k*C3*C4*C9*CO[217 -
0.28(h/t)][0.71 + O.O15(N/t)]
h/t = 78.00 Pe( 2)= 1 * 0.249 kips = 0.249 kips
h/t = 78.00 Pe(22)= 1 * 0.249 kips = 0.249 kips
Pend= 0.499 kips
Pint= t^2*k*Cl*C2*C9*C0[538 -
0.74(h/t)][0.75 + O.Oll(N/t)]
h/t = 78.00 Pi( 2)= 1 * 0.595 kips = 0.595 kips
h/t = 78.00 Pi(22)= 1 * 0.595 kips = 0.595 kips
Pint= 1.189 kips
E = 29,500 ksi
Fy = 50.00 ksi
kv = 5.34 -
for unreinforced webs
0,96O*Sqr(Ekv/Fy) = 53.88
1,415*Sqr(Ekv/Fy) = 79.42
h/t = 78.00
h/t = 78.00 1 V( 2) = 1
V(22) = 1
*
*
1.035 kips =
1.035 kips =
1.035 kips
1.035 kips
(Eq. C3.2-2)
(Eq. C3.2-2)
Vn = 2.069 kips
PAGE NO. 8 1
DATE: 04-20-1999
John F. B u t t s C A s s o c i a t e s , I n c .
2480 Vantage D r i v e
Colorado S p r i n g s , CO 80919
( 7 1 9 ) 598-7666
P e r AISI Cold-Formed S t e e l
Design Manual, 1996 E d i t i o n
DIMENSIONS
SPECIAL CONDITIONS
Seam R o t a t i o n : 90 deg.
Effective Properties
End Bearing
Ix Sx IY SY Mnx M ~ Y Vnx Pne Pnei
(in4) (in3) (in4) (in3) (in-k) (in-k) (kip) (kip) (k/in)
Torsional Properties
Xo Ro Bet a Cw Jv*1000 Fy Fu E G
(in) (in) (in6) (in4) (ksi) (ksi) (ksi) (ksi)
-1.102 5.291 0.957 8.44 0.09.2 50 65 29500 11300
Shear, moment and bearing values shown are nominal values and must
be modified by the appropriate factors of safety (ASD) or
resistance factors (LRFD).
Moment o f I n e r t i a @ 90 d e g r e e R o t a t i o n
ELEMENT L Y LY LYY I0
PAGE NO. 85
DATE: 04-20-1999
ELEMENT L Y LY LYY I0
ELEMENT L Y LY LYY I0
ELEMENT L Y LY LYY I 0
ELEMENT L Y LY LYY 10
N/t= 83.33
k = 1.515
Cl = 0.887
C2 = 0.960
C3 = 0.*830
C4 = 0.900
C9 = 1.000
CO = 1.000 - Element 2, 22
Pint= t^2*k*Cl*C2*C9*C0[538 -
0.74(h/t)][0.75 + O.Oll(N/t)]
h/t = 78.00 Pi( 2)= 1 * 0.595 kips = 0.595 kips
h/t = 78.00 Pi(22)= 1 * 0.595 kips = 0.595 kips
Pint= 1.189 kips
E = 29,500 ksi
Fy = 50.00 ksi
kv = 5.34 -
for unreinforced webs
0.960*Sqr(Ekv/Fy) = 53.88
1.415*Sqr(Ekv/Fy) = 79.42
Vn = 2.069 kips
PAGE NO. 90
DATE: 04-20-1999
J o h n F. B u t t s & A s s o c i a t e s , I n c .
2480 Vantage Drive
Colorado S p r i n g s , CO 80919
( 7 1 9 ) 598-7666
P e r AISI Cold-Formed S t e e l
Design Manual, 1996 E d i t i o n
DIMENSIONS
SPECIAL CONDITIONS
Seam R o t a t i o n : 90 deg.
Effective Properties
End Bearing
Ix Sx IY SY Mnx M ~ Y Vnx Pne Pnei
(in4) (in3) (in4) (in3) (in-k) (in-k) (kip) (kip) (k/in)
0.226 0.123 0,000 0.000 3.93 0.00 2.069 0.181 0.159
Torsional Properties
Xo Ro Beta Cw Jv*1000 Fy Fu E G
(in) (in) (in6) (in4) (ksi) (ksi) (ksi) (ksi)
-1.021 5.885 0.970 .11.36 0.101 50 65 29500 11300
Shear, moment and bearing values shown are nominal values and must
be modified by the appropriate factors of safety (ASD) or
resistance factors (LRFD).
ELEMENT L Y LY LYY 10
PAGE NO. 9 4
DATE: 0 4 - 2 0 - 1 9 9 9
ELEMENT L Y LY LYY 10
ELEMENT L Y LY LYY I 0
ELEMENT L Y LY LYY 10
ELEMENT L Y LY LYY 10
- Element 2, 22
Pend= t^2*k*C3*C4*C9*C0[217 -
0.28(h/t)][0.71 + 0.015(N/t)]
h/t = 78.00 Pe( 2)= 1 * 0.249 kips = 0.249 kips
h/t = 78.00 Pe(22)= 1 * 0.249 kips = 0.249 kips
Pend= 0.499 kips
-
Pint= tA2*k*C1*C2*C9*C0[538 0.74(h/t)][0.75 + O.Oll(N/t)]
h/t = 78.00 Pi( 2)= 1 * 0.595 kips = 0.595 kips
h/t = 78.00 Pi(22)= 1 * 0.595 kips = 0.595 kips
Pint= 1.189 kips
E = 29,500 ksi
Fy = 50.00 ksi
kv = 5.34 -
for unreinforced webs
0,96O*Sqr(Ekv/Fy) = 53.88
1.415*Sqr(Ekv/Fy) = 79.42
Vn = 2.069 kips
PAGE NO. 99
DATE: 04-20-1999
P e r AISI Cold-Formed S t e e l
Design Manual, 1996 E d i t i o n
DIMENSIONS
P a n e l ~ o t t o mWidth =
P a n e l O v e r a l l Width =
P a n e l O v e r a l l Height=
SPECIAL CONDITIONS
Seam R o t a t i o n : 90 deg.
G r o s s Section Properties
Effective Properties .
End B e a r i n g
Ix Sx IY SY Mnx MnY Vnx Pne Pnei
(in4) (in3) (in4) (in3) (in-k) (in-k) (kip) (kip) (k/in)
Torsional Properties
Xo Ro Beta Cw Jv*lOOO Fy Fu E G
(in) (in) (in6) (in4) (ksi) (ksi) (ksi) (ksi)
F a c t o r s of S a f e t y (ASD) R e s i s t a n c e F a c t o r s (LRFD)
R (Compression) = 1.80 @ (Compression) = 0.85
R (Tension) = 1.67 @ (Tension) = 0.95
R (Web C r i p p l i n g ) = 1.85 @ (Web C r i p p l i n g ) = 0.75
R (Bending) = 1.67 . @ (Bending) = 1.11
R (Shear) = 1.67 @ (Shear) = 0.90
PAGE NO. 102
DATE: 04-20-1999
ELEMENT L Y LY LYY 10
PAGE NO. 103
DATE: 04-20-1999
ELEMENT L Y LY LYY 10
ELEMENT L Y LY LYY I0
ELEMENT L Y LY LYY 10
ELEMENT L Y LY LYY 10
N/t= 83.33
k = 1.515
C1 = 0,887
C2 = 0.960
C3 = 0.,830
C4 = 0.900
C9 = 1.000
CO = 1.000 - Element 2, 22
-
Pend= t^2*k*C3*C4*C9*C0[217 0.28(h/t)][0.71 + 0.015(N/t)]
h/t = 78.00 Pe( 2)= 1 * 0.249 kips = 0.249 kips
h/t = 78.00 Pe(22)= 1 * 0.249 kips = 0.249 kips
Pend= 0.499 kips
-
Pint= t^2*k*Cl*C2*C9*C0[538 0.74(h/t)][0.75 + O.Oll(N/t)]
h/t = 78.00 Pi( 2)= 1 * 0.595 kips = 0.595 kips
h/t = 78.00 Pi(22)= 1 * 0.595 kips = 0.595 kips
Pint= 1.189 kips
E = 29,500 ksi
Fy = 50.00 ksi
kv = 5.34 -
for unreinforced webs
0.960*Sqr(Ekv/Fy) = 53.88
1.415*Sqr(Ekv/Fy) = 79.42
Vn = 2.069 kips
PAGE NO. 108
DATE: 04-20-1999
2. A l l o w a b l e u n i f o r m l o a d s a r e d e t e r m i n e d p e r t h e following:
a ) Allowable Shear S t r e s s (Fv) [AISI C3.21
. b ) Combined Bending and S h e a r [AISI C3.31
c ) Combined Bending & Web C r i p p l i n g [AISI C3.51
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 i n
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
Simple Span : Max. Span = 8.666 f t (L/180)
Two s p a n : Max. Span = 10.411 f t (L/180)
T h r e e Span +: Max. Span = 10.666 f t (L/180)
PAGE NO. S30
DATE: 04-20-1999
2. A l l o w a b l e u n i f o r m l o a d s a r e d e t e r m i n e d p e r t h e following:
a ) Allowable Shear S t r e s s (Fv) [AISI C3.21
b ) Combined ending and S h e a r [AISI C3.31
c ) Combined Bending & Web C r i p p l i n g [AISI C3.51
3. F a c t o r s of S a f e t y u s e d t o d e t e r m i n e u n i f o r m l o a d s :
R (Bending) = 1.67
R (Shear) = 1.67
R (Web C r i p p l i n g ) = 1 . 8 5
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 in
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
S i m p l e Span : Max. Span = 8.666 it (L/180)
Two s p a n : Max. Span = 1 0 . 4 1 1 f t (L/180)
T h r e e Span +: Max. Span = 10.666 it (L/180)
PAGE NO. S31
DATE: 04-20-1999
2. A l l o w a b l e u n i f o r m l o a d s a r e d e t e r m i n e d p e r t h e following:
a ) Allowable Shear S t r e s s (Fv) [AISI C3.21
b ) Combined Bending and S h e a r [AISI C3.33
c ) Combined Bending & Web C r i p p l i n g [AISI C3.51
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 in
6. C o n c e n t r a t e d l o a d = 1 5 0 l b a t mid-span, l o a d w i d t h = 4 i n
S i m p l e Span : Max. Span = 8.666 f t (L/180)
Two Span : Max. Span = 1 0 . 4 1 1 f t ( L / 1 8 0 )
T h r e e Span +: Max. Span = 10.666 f t (L/180)
PAGE NO. S33
DATE: 04-20-1999
3. F a c t o r s of S a f e t y u s e d t o d e t e r m i n e uniform l o a d s :
R (Bending) = 1.67
R (Shear) = 1.67
R (Web C r i p p l i n g ) = 1.85.
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 in
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
Simple Span : Max. Span = 8.302 f t (L/180)
Two Span : Max. Span = 9.786 f t (L/180)
Three Span +: Max. Span = 10.025 f t (L/180)
PAGE NO. S35
DATE: 04-20-1999
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 in
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
Simple Span : Max. Span = 8.302 f t (L/180)
Two s p a n : Max. Span = 9.786 f t (L/180)
Three Span +: Max. Span = 10.025 f t (L/180)
PAGE NO. S36
DATE: 04-20-1999
2. A l l o w a b l e u n i f o r m l o a d s are d e t e r m i n e d p e r t h e following:
a ) Allowable Shear S t r e s s (Fv) [AISI C3.21
b ) ~ o m s i n e dB e n d i n g and S h e a r [AISI C3.33
c ) Combined B e n d i n g & Web C r i p p l i n g [AISI C3.53
3. F a c t o r s o f S a f e t y u s e d t o d e t e r m i n e u n i f o r m l o a d s :
R (Bending) = 1.67
R (Shear) = 1.67
R (Web C r i p p l i n g ) = 1.85
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 i n
6. C o n c e n t r a t e d l o a d = 1 5 0 l b a t mid-span, l o a d w i d t h = 4 i n
S i m p l e Span : Max. Span = 7.849 f t ( L / 1 8 0 )
Two Span : Max. Span = 9.253 f t (L/180)
T h r e e Span +: Max. Span = 9.479 f t (L/180)
PAGE NO. S38
DATE: 04-20-1999
2. A l l o w a b l e u n i f o r m l o a d s a r e d e t e r m i n e d p e r t h e following:
a ) Allowable S h e a r S t r e s s ( F v ) [AISI C3.21
b ) Combined Bending and S h e a r [AISI C3.31
c ) Combined Bending & Web C r i p p l i n g [AISI C3.51
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 i n
3. F a c t o r s of S a f e t y used t o d e t e r m i n e uniform l o a d s :
51 (Bending) = 1.67
R (Shear) = 1.67
R (Web C r i p p l i n g ) = 1.85
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 i n
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
Simple Span : Max. Span = 7.849 f t (L/180)
Two s p a n : Max. Span = 9.253 f t (L/180)
Three Span +: Max. Span = 9.479 f t (L/180)
PAGE NO. S41
DATE: 04-20-1999
2. Allowable u n i f o r m l o a d s a r e d e t e r m i n e d p e r t h e following:
a ) Allowable Shear S t r e s s (Fv) [AISI C3.21
b ) Combined Bending and S h e a r [AISI C3.31
C ) Combined Bending & Web C r i p p l i n g [AISI C3.51
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 in
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
Simple Span : Max. Span = 7.462 f t (L/180)
Two Span : Max. Span = 8.797 f t (L/180)
Three Span +: Max. Span = 9.012 f t (L/180)
PAGE NO. S42
DATE: 04-20-1999
2. A l l o w a b l e u n i f o r m l o a d s a r e d e t e r m i n e d p e r t h e following:
a) A l l o w a b l e S h e a r S t r e s s ( F v ) [AISI C3.21
b ) Combined Bending and S h e a r [AISI C3.31
c ) Combined Bending & Web C r i p p l i n g [AISI C3.51
5. Minimum p a n e l s u p p o r t b e a r i n g l e n g t h = 2.00 i n
6. C o n c e n t r a t e d l o a d = 150 l b a t mid-span, l o a d w i d t h = 4 i n
Simple Span : Max. Span = 7.462 f t ( L / 1 8 0 )
Two Span : Max. Span = 8.797 f t ( L / 1 8 0 )
T h r e e Span +: Max. Span = 9.012 f t (L/180)