Professional Documents
Culture Documents
a. 3
b. 4
c. 5
d. 6
2. Which type of work permit will you take for cutting and Welding job in open space at
Aramco Facility?
a. Cold Work
b. Hot Work
c. Confined
d. EOLB
3. Which type of Work Permit you will take for only entering a Vessel at an Aramco facility?
a. Cold Work
b. Hot Work
c. Confined Space Entry
d. EOLB
4. Which G.I. No. is applicable for Saudi Aramco Work Permit System?
a. 2.100
b. 6.012
c. 7.028
d. 8.001
5. Which one is the example of an Unsafe Act in the given below options?
a. Taking Shortcuts and not following checklists procedures and process
b. Extreme Weather
c. Both (a) & (b)
d. None of the above
6. Which one is example of an Unsafe Condition in the given below options?
a. Taking Shortcuts and not following checklists procedures and process
b. Extreme Weather
c. Both (a) & (b)
d. None of the above
7. Most incidents in the workplace are caused by combination of Unsafe Act and ---------------?
A. Hazards
B. The Environment
C. Unsafe Condition
D. Safe acts
8. The most common cause of incidents at Saudi Aramco is failure to follow --------------?
A. Yellow lines in the workshop.
B. Co-workers good suggestions
C. Rules and Procedures
D. Supervisors Instructions
1 | Page
a. Safety and environment Hazards
b. Health and Gravity Hazards
c. Pressure and Motion Hazards
d. Safety and Health Hazards
11. Which one among the following is an example of a safety hazard?
a. Electrical Hazard
b. Biological Hazard
c. Chemical Hazard
d. Temperature Hazard
12. Which one among the following is an example of a Health hazard?
a. Electrical Hazard
b. Gravity Hazard
c. Mechanical Hazard
d. Chemical Hazard
13. A _____ is anything that can have an adverse impact on your safety?
A. Health Hazard
B. Work Permit System
C. Safety Hazard
D. All of above
14. A _____ is anything that can have an adverse impact on your health?
A. Health Hazard
B. Work Permit System
C. Safety Hazard
D. All of above
15. During the JSI you must complete the work permit and the Hazard Analysis Checklist on
the back.
A. True
B. False
2 | Page
d. None of the above
20. Using Warning Signs for a scaffolding erection is an example of:
a. Administrative Control
b. PPE Control
c. Engineering Control
d. None of the Above
21. A work permit in Aramco is an Example of which type of Control:
a. Engineering Control
b. PPE Control
c. Administrative Control
d. None of the Above
22. Wearing SCBA in Hazardous environment is an example of:
a. Engineering Control
b. Administrative Control
c. PPE & RPE Control
d. None of the Above
23. The three steps used in Aramco to control the Hazards:
a. Engineering , Administrative and PPE Control
b. Engineering, Administrative and Safety Control
c. Engineering, Administrative and Health Control
d. None of the Above
24. Wet floors and Trailing Cables can lead to which type of hazard:
a. Slip Hazard
b. Trip Hazard
c. Fall Hazard
d. ALL of the above
25. As a Receiver, What things will you inspect in a Tool or Equipment:
a. Inspect for any Defective Tool or equipment
b. Inspect for any prohibited tools or equipment.
c. Inspect that the Right tool or equipment is used for the right job
d. All of the above
26. Noise & Vibration & Temperature Hazard is an Example of:
a. Safety Hazard
b. Health Hazard
c. Both Safety and Health Hazards
d. None of the Above
27. What control measures will you select to control Noise Hazards:
a. Replace , Equipment or processes with quieter ones
b. Limit Employee Exposure
c. Periodic Breaks, Warning Signs and Hearing Protection (Ear Plug) to be used
d. All of the above
28. Machine Moving Parts to be guarded if less than ________ above the working Surface:
a. 3.5 m
b. 1.8 m
c. 2.5 m
d. 1.8 m
29. What will be the pressure Testing Control Measure?
a. Notify others with barriers and signage
b. Relief system is calibrated
3 | Page
c. Release of pressure testing Material is under control
d. All of the above
30. In heavy rain the outdoor activity of cutting and welding will be:
a. Stopped
b. Continued
c. If supervisor says it should be continued
d. Required another work permit to continue
31. In Saudi Aramco, The two most effective control measures for heavy equipment like Crane
will be:
a. Certified operator and Fire Extinguisher
b. Valid Crane inspection and Barricade the area
c. Certified operator and Valid Crane inspection
d. Barricade the area and Fire extinguisher
32. For selecting the proper PPE’s in Hazardous chemical Area, we shall look for:
a. Types of PPE’s Available
b. Half face respirator
c. CHB
d. None of the above
33. In Saudi Aramco, the four gases in hazardous environment, we record on Permit:
a. Carbon Monoxide CO, Carbon Dioxide CO2, Sulphur Dioxide SO2, Hydrogen Sulphide
H2S
b. Carbon Monoxide CO, Hydrogen Sulfide H2S,Oxygen O2, Lower explosive Limit LEL
e. Hydrogen Sulphide H2S, Sulphur Dioxide SO2, Lower explosive Limit LEL, Oxygen O2
c. None of the Above
34. Using SCBA in Hazardous environment, we will maintain:
a. Negative Pressure
b. Positive Pressure
c. No pressure
d. Any pressure can be kept inside face seal.
35. For Selecting RPE in Toxic Environment, we should always check :
a. RPE Suitable for the Hazard
b. Gas sampling Reading
c. Face Seal Properly Tight with positive pressure
d. ALL of the Above
36. The personal H2S monitor should always be worn:
a. In Refineries
b. Working near crude process area
c. Gas and oil separation plants
d. ALL of the above
37. In Saudi Aramco, working at height will be considered if the potential fall distance more
than:
a. 1.2 m
b. 1.6 m
c. 1.8 m
d. 2.0 m
38. The three common hazards for all elevated Work platforms:
a. Falling of Personnel, Falling of Loose objects, Collapsing of elevated Platform
b. Falling of Personnel, Falling of Loose Objects, Extreme Weather
c. Falling of Personnel, No anchor point for fall arrest, Collapsing of elevated platform
4 | Page
d. None of the above
39. Identify two common excavation hazards?
a. Side Wall Collapse
b. Underground Utilities
c. Both ‘a’ & ‘b’
d. None
5 | Page
48. A group of contractor wants to make a welding joint on a pipe spool inside an excavation;
having a depth of 2m.Which type of permits they will be required.
a. Hot and Cold Work
b. Hot and Confined Space entry
c. Cold and Confined Space Entry
d. EOLB and Confined Space Entry
49. A serious and life threatening hazard in an Excavation:
a. Cave in of sidewalls
b. Striking underground utilities
c. Toxic gas accumulation
d. ALL
50. Why we have to identify and mark all underground services before digging:
a. To prevent digging up live cables with Back hoe
b. To prevent Jack Hammer contacting the Live Cables
c. To prevent Hand Digging around live cables
d. All
51. Toxic Gas H2S Hydrogen Sulphide is
a. Heavier Than air
b. Lighter than air
c. Equal to Air
d. None
52. Heavy equipment shall be kept away from the edge of Excavation for:
a. 3m
b. 4m
c. 2m
d. 1m
53. For digging excavation mechanically in Aramco,you will be required:
a. Pre Excavation Checklist
b. Excavation Checklist
c. Hot work Permit
d. All
54. How much away at least Spoils, Debris should be kept from excavation edge?
a. 1ft (30cm)
b. 2ft (60 cm)
c. 3ft (90cm)
d. 4ft (120cm)
55. Scaffold should not be erected near the excavation; it should be at least:
a. 1.5 times the depth of trench
b. 2 times the depth of trench
c. 2.5 times the depth of trench
d. None of the Above
56. What is the minimum distance a heavy equipment should be placed near the edge of
excavation:
a. 3m
b. 4m
c. 2m
d. 1m
6 | Page
57. Excavating machines are not allowed to operate closer than -------- from the nearest
underground hazard.
a. 4m
b. 3m
c. 2m
d. 1m
58. HAZCOM stands for:
a. Hazard Communication
b. Health Communication
c. Both (a) & (b)
d. None of the Above
59. Compressed gas cylinders should be stored:
a. in up-right position
b. away from all heat sources and direct sun light
c. Clearly identify and label all cylinder
d. All of the above
60. Why do we slope or bench excavations?
a. To prevent sidewall collapse
b. Always present in air low Concentration
c. Found in the buried ground
d. All of the above
61. What is the best method of preventing the side wall of an excavation from collapsing?
a. Engineering control
b. Administrative Control
c. PPE’s Control
d. Sloping, Benching or Shoring
62. What do you call the excavation support system that uses the engineered structure to
support the sidewall?
a. Dust and Noise
b. Clean Air
c. Shoring
d. None of the above
63. What must be done if traffic must be re routed because of an excavation?
a. Silica Sand
b. Water Based slurry
c. Clean air supply to the operator hood
d. Use barricades and signs
64. H2S is also Called:
a. Silent Killer
b. Sour Gas
c. Sewer Gas
d. All of the above
65. What can be used to mark an excavation at night so people can see it?
a. Flashing Light
b. Tube Light
c. Search Light
d. None of above
66. What can be used to mark an excavation at night so people can see it?
a. Flashing Light
7 | Page
b. Guardrail and Barriers
c. Both ‘a’ and ‘b’
d. None of above
67. Who should be assigned to direct traffic around an excavation?
a. Fire Watch
b. Supervisor
c. Flag man
d. Signal Person
68. What must be installed to allow people to cross over an excavation?
a. Man Basket
b. Ladder
c. Scaffolding
d. A walk-way with guardrail
69. What is the only way to find out if the atmosphere inside the excavation is safe
a. No smell
b. Rotten egg smell
c. Take gas test by certified gas tester
d. None
70. How can toxic material get into our lungs?
a. Ingestion
b. Inhalation
c. Absorption
d. All of above
71. What is the best protection for eyes?
a. Glasses with Side Shied
b. Goggles
c. FaceShield
d. All of above
72. What is the minimum safety equipment that a worker wear when there is danger of head
injury?
a. Safety Helmet
b. H2SO4 Corrosive acid
c. Both (a) and (b)
d. None
73. Why must safety helmets not be painted?
a. It is helpful
b. Paint could hide crack or damage
c. Impossibly dangerous to life and health
d. Instantly dangerous to life and health
74. Why metal helmets are prohibited at all Saudi Aramco facilities
a. They store and conduct Electricity
b. Start work without wearing breathing apparatus
c. Start work but must wear breathing apparatus
d. None
75. Welding, cutting and brazing tasks in a confined space increase the risk of:
a. Carbon Monoxide exposure CO
b. Deficiency of oxygen O2 level
c. Asphyxiation or suffocation Hazard
d. All of the above
8 | Page
76. Your hearing will be damaged and you will start to suffer hearing loss at which noise
level?
a. 85 DB
b. Above 85DB
c. 90 DB
d. All of above
77. How can you tell if hearing protection should be worn in a work area?
a. Obtained a Cold work permit
b. Obtained a hot work permit
c. Obtained a confined space entry permit
d. Look for the warning signs
78. What is the emergency No. of Saudi Aramco?
a. 911
b. 999
c. 910
d. 988
79. How can you prevent most hand injuries?
a. Allow workers to enter and perform work
b. Wear Gloves
c. Contains or has the possibility to contain a hazardous atmosphere
d. All of the above
80. Identify the confined space example:
a. Columns
b. Vessels
c. Manholes
d. All of the above
81. What are the roles you need for a confined space entry?
a. A CSE supervisor, Entrants and a stand by man
b. A CSE supervisor, Other employees and exit point
c. A CSE supervisor, flagman and stand by man
d. None of the above
82. Where must workers wear personnel fall prevention equipment?
a. Above 1.8m or 6 feet
b. 2m or 8 feet
c. 1m or 3 feet
d. All of the above
83. What setting should be used whenever using SCBA in potentially hazardous
atmospheres?
a. Positive Pressure
b. Negative Pressure
c. Both (a) and (b)
d. None of the above
84. What should you do before using an SCBA?
a. Inspect it
b. Be Trained
c. Wait for 30 minutes so that the air quality becomes good
d. Both ‘a’ and ‘b’
85. What is used with a cascade breathing air system to give emergency breathing air if you
must escape or if the breathing air supply stops?
9 | Page
a. Wear SCBA
b. No need to do anything
c. Both (a) and (b)
d. A 5 minute bottle escape pack
86. What equipment uses compressed air?
a. Abrasive Blasting
b. Impact Wrenches
c. Jackhammer
d. Spray painting equipment
e. All of above
87. Identify two hazards when using compressed air equipment?
a. Damage Hoses
b. Missing Coupling Safety Pins
c. Both ‘a’ and ‘b’
d. None of above
88. Why are most paint and paint thinners in Saudi Aramco hazardous
a. They are Flammable and Toxic
b. They are not Flammable and Toxic
c. Both ‘a’ and ‘b’
d. None
89. What is the best way to understand the hazardous properties of a paint?
a. Warning Labels
b. MSDS
c. CHB
d. All of above
90. What is the best way to make sure flammable paint vapors will not become explosive
a. Ventilation
b. Safe environment to work
c. Electrocution not there
d. None of the above
91. To Stop the flow of Abrasive material if released what you will use?
a. Dead man Switch
b. Fail safe Switch
c. Flag man
d. Signal Person
92. To prevent static charge from developing what you will do?
a. Bonding
b. Grounding
c. Both ‘a’ and ‘b’
d. None
93. What you will do before any ladder is used?
a. Use Self contained breathing apparatus
b. Use Self contaminated breathing apparatus
c. Inspect it
d. Wash your hand
94. You can paint the ladders
a. True
b. False
95. Why we can’t paint the ladders
10 | Page
a. Because Used for working on energized equipment and performing maintenance
b. Because used for working at height
c. Because used for low risk job
d. Paint could hide cracks or damage
96. What is the correct angle to use when placing a ladder?
a. 45 degree and 5 to 3 slope ratio
b. 75 degree and 4 to 1 slope ratio
c. 65 degree and 5 to 3 slope ratio
d. 95 degree and 5 to 3 slope ratio
97. For temporary access jobs that do not take a long time to complete what you will use?
a. Crane
b. Scaffolding
c. Ladder
d. MEWP
e. ALL of the Above
98. You can use ladder temporary as a working platform like scaffold work, truck bed or man
basket?
a. True
b. False
99. Metal ladders are best near the energized electrical equipment or electric lines?
a. True
b. False
100. Why do we not use metal ladders or ladders with metal reinforced side rails near
electrical equipment?
a. Official permission is required
b. The employee performing maintenance is not Trained
c. It could cause an electric shock
d. All of the above
101. What is the best way to climbing a ladder?
a. Checked
b. Verified
c. 3 point of contact
d. Cross check
102. What must be installed near the access points of scaffolding
a. Maintenance Log
b. Supervisor Log
c. Scaffolding tag
d. Anything
103. What is used to tell people to keep away from scaffold?
a. Hold Tag
b. Paper
c. Safe means of access
d. Barricade and warning Sign
104. What must be installed on every scaffold?
a. Scaffolding Tag
b. Paper
c. Wire
d. Safe means of access
11 | Page
105. What tells an operator of an elevating work platform the checks that must be made
during the pre-operational inspection?
a. Double block and Bleed
b. Single Block valves
c. Manufacturer’s Instructions
d. Both (a) and (b)
106. What must workers wear when they are being lifted in an elevating work platform
basket?
a. Safety harness
b. Safety Belt
c. Gloves
d. Anything
107. What should be done to warn employees to stay away from an elevating work
platform while it is in operation?
a. Install barricades around the machine
b. Blind list
c. Tag List
d. All of above
108. To prevent the accidental startup of equipment what we will use:
a. Hazard Analysis Checklist
b. LOTO System
c. Work Permit System
d. All of above
109. Who must install lock and tags on main circuit breakers before work starts?
a. Affected Employees
b. Other Employees
c. Authorized Employees
d. All of above
110. Who must be at the work site when work must be done on energized electrical
circuits?
a. Hazard Analysis Checklist
b. Two electricians and foreman
c. Rigger 1
d. All of above
111. What are the closest distance men or equipment can work away from energized
upto 50 kv power lines?
a. 5 feet
b. 10 feet
c. 15 feet
d. 25 feet
112. What are the closest distance men or equipment can work away from energized
51kv to 250kv power lines?
a. 5 feet
b. 20 feet
c. 15 feet
d. 25 feet
113. What are the closest distance men or equipment can work away from energized
above 250 kv power lines?
a. 5 feet
12 | Page
b. 10 feet
c. 15 feet
d. 25 feet
114. What are the closest distance men or equipment can work away from energized
251.4kv power lines?
a. 5 feet
b. 10 feet
c. 15 feet
d. 25 feet
115. What safety precaution should be taken before working a pneumatic or hydraulic
system?
a. Make sure it is not depressurized
b. Make sure it is depressurized
c. Both ‘a’ and ‘b’
d. None
116. What should be done before a hydro test begins?
a. Make sure it is not depressurized
b. Barricade and sign
c. Both ‘a’ and ‘b’
d. None
117. What is the most serious hazard about a hydro test?
a. Make sure it is not depressurized
b. Failure of Equipment
c. Both ‘a’ and ‘b’
d. None
118. What is the most serious hazard about a hydro test?
a. Incorrect Material
b. Failure of Equipment
c. Failure of Relief System
d. All of above
119. What should be done to keep people away from a hydro test?
a. Incorrect Material
b. Failure of Equipment
c. Install barricades and warning signs
d. All of above
120. How do we protect ourselves from the radiation used when radiography work is
done?
a. Incorrect Material
b. Equipment should be correct
c. Time, Distance and Shielding
d. All of above
121. How must compressed gas cylinders be stored?
a. Upright
b. Shaded Area
c. Ventilated Area
d. All of above
122. How far apart must compressed gas cylinders containing flammable gas kept from
those containing oxidizers when not in use?
a. At least 6.1m or 20 feet
13 | Page
b. 7 m or 23.1 feet
c. 3m or 10 feet
d. All of above
123. What is the correct way to move a compressed gas cylinder?
a. Cylinder Rack
b. Cylinder Trolley
c. Material Basket
d. All of above
124. What must be done before using any equipment that will dig into the ground?
a. Use Incorrect Material
b. Equipment should be inspected
c. Locate and mark all underground hazards
d. All of above
125. What should be done when towing trailer mounted equipment in congested area or
near plant equipment?
a. Assign a Flagman
b. Assign a Spotter
c. Use Relief System
d. All of above
126. What can be done to prevent heavy equipment from hitting equipment or people
while it is being operated?
a. Use a Flagman and barricades
b. Assign a Spotter
c. Use Relief System
d. All of above
127. What should be done if a heavy equipment operator’s certificate has expired?
a. Assign a Flagman
b. Assign a Spotter
c. Use Relief System
d. He must not operate the equipment
128. What must crane operator do before he uses a crane?
a. Inspect it
b. Lift Plan
c. Use Relief System
d. Both ‘a’ & ‘b’
129. What must crane operator do before he uses a crane?
a. Inspect it
b. Use manufacturer manual
c. Use Relief System
d. Both ‘a’ & ‘b’
130. What must attachment to a crane before it can be used?
a. Inspection sticker
b. Lift Plan
c. Use Relief System
d. Both ‘a’ & ‘b’
131. What must attachment to a crane before it can be used?
a. Inspection sticker
b. Operator Certificate
c. Use Relief System
14 | Page
d. Both ‘a’ & ‘b’
132. What must be done if a lifting sling is found damaged?
a. Inspection sticker
b. Lift Plan
c. Use Relief System
d. Remove it from service
133. What should be done before using any hand tools?
a. Inspect it
b. Nothing should be done
c. Use Relief System
d. Remove it from service
134. What must be done if a hand tool is found in poor condition?
a. Inspection sticker
b. Lift Plan
c. Use Relief System
d. Remove it from job site
135. What is the most common problem with electric power tools?
a. Inspection sticker
b. Short Circuit
c. Relief System
d. Damaged cords or receptacles
136. Why is frayed or damaged electrical wiring dangerous on power tools?
a. Inspection sticker
b. Open Circuit
c. Short Circuit
d. It could cause an electrical shock
137. Why must welders and other workers nearby wear special eye and face protection?
a. Welding rule
b. Welding light is dangerous
c. To protect them from Ultraviolet (UV) radiation
d. It is needed
138. Whenever you are testing H2S you will wear SCBA?
a. True
b. False
a. 4
b. 3
c. 2
d. 3.5
15 | Page
c. exit and egress
confined spaces?
a. Tanks
b. Vessels
c. Manholes
d. All answers
in confined spaces?
a. Temperature
b. Noise
c. Hazardous atmosphere
space?
a. Limited access
working space
a confined space?
b. Toxic atmospheres
16 | Page
considered when evaluating working conditions
in confined spaces.
a. True
b. False
or a project site?
by a certified Issuer
work permit
space entry?
them
Man’s responsibilities?
17 | Page
enters
emergency
responsibilities?
assignment
Man
a. True
b. False
(CSE) permit.
a. True
b. False
18 | Page
a. True
b. False
a. procedures
b. stories
c. quotation
d. essay
a. True
b. False
a. No Entry is permitted
respirator
19 | Page
b. Permitted to perform Hot Work and
Head approval
is allowed
without SCBA
by?
a. Air mover
20 | Page
b. Vacuum truck
c. Entry log
d. Training plan
a fire watch
atmosphere is:
b. Hand Signal
21 | Page
combination of unsafe acts and .
a. hazards
b. the environment
c. unsafe conditions
d. safe acts
d. supervisors instructions
C) Both A & B
D) None of above
e. All answers
lanyards?
22 | Page
a. To have a place to put their tools
d. To be more comfortable
present in area
happens
ear plugs
a. Guarding
b. un-guarding
c. guardianship
d. Velocity
elevated areas?
people away
23 | Page
lifts, manbaskets, and for work on scaffolds?
wear?
a. SCBA or SABA
properly isolated?
enter by accident
24 | Page
175.What is the meaning of Red tag:
C) Both A & B
D) None
a. Wooden planks
a scaffold?
d. Standby man
25 | Page
a. materials must be in good condition (no
b. no leaning
dismantling.
the scaffold.
a harness
Matters
a) Rigger level 1
b) Rigger level 2
c) Rigger level 3
d) All of above
or equipment
26 | Page
184. What should be done if a heavy equipment
equipment
superintendent
Rigger II
certificate
certificate
from equipment
operating area?
can be used?
27 | Page
a. Load moment indicator and tire pressure
finished
and cables
to?
c. Carpentry or woodworking
work in an excavation?
Place
excavation?
28 | Page
a. Install barricades and warning signs
of an excavation?
blocked
excavation
warning signs
or blocked
underground hazard?
a. 3 meters
b. 1 meters
c. 5 meters
d. 10 meters
excavation
29 | Page
d. Workers in the excavation could get an
electric shock
digging.
d. All answers
away.
a. True
b. False
D. All of above
happening
material
30 | Page
months
airborne
or oxidizers?
b. 5 meters or 16 feet
c. 10 meters or 33 feet
d. 3 meters or 10 feet
pins
hoses
d. It is a GI requirement
31 | Page
c. Ignition source and water spray
safety shoes
bonding
equipment
equipment
area?
in confined spaces
32 | Page
confined spaces
a. Upwind
b. Downwind
c. Cross wind
D) All of above
blasting?
33 | Page
d. A fire watch is not required
areas?
(CO) exposure
a. Regular inspections
c. Good housekeeping
or casualties (victims)
34 | Page
c. To ensure everyone knows their roles and
responsibilities
report:
supervisor.
signal is given
35 | Page
A) True
B) False
A.Lift Plan
B.Check Hazards nearby the area
C.Operator Certificate
D.Both A & B
221. Energy must be controlled to prevent the unexpected startup or movement of equipment
during installation, repair, maintenance or service.
a. True
b. False
a. True
b. False
a. True
b. False
a. True
b. False
225. The first step in lockout / tagout is to shut down the equipment.
36 | Page
a. True
b. False
226. Affected employees must be notified when equipment is being locked and tagged out and
when it is being restored to normal working order.
a. True
b. False
227. When several employees are working on the same piece of equipment, only one of them
needs to attach his or her lock and tag.
a. True
b. False
228. Each lockout device must be tagged individually and identify when and why the equipment
was locked out and by whom.
a. True
b. False
229. The last step in the lockout / tagout procedure is to test the equipment to make sure all
energy has been released or controlled.
a. True
b. False
230. Startup procedures must begin with preparations to make sure the area and equipment are
safe for restart.
a. True
b. False
231. Lock Out Tag Out program does not apply to do work on cord and plug equipment when
unplugged from energy source.
a. True
37 | Page
b. False
a. True
b. False
233. Single block Valve is not an approved isolation method for hydrocarbon service or confined
space entry.
a. True
b. False
234.Double block and bleed isolation method is not approved for work if pipe contains
hazardous material.
a. True
b. False
d.All of above
236. Blinding isolation method is not approved for confined space entry.
a. True
b. False
237. Contractors shall always be the first to install and the last to remove locks and tags
a. True
b. False
38 | Page
238. Double block and bleed isolation method
39 | Page
40 | Page