Professional Documents
Culture Documents
工程设计综合资质
甲级证书A112000022
T21B07-2600-CC84
计算书 Calculation sheet 日期:20220526 版次: C01
C01 20220526
版次 文件说明 日期 编制 校对 审核 审定
Rev. Document Description DATE DESIGN CHECK REVIEW APPROVAL
CABR-PKPM
-1-
CABR-PKPM
-2-
CABR-PKPM
-3-
CABR-PKPM
-4-
CABR-PKPM
The elastic plate, out of plane design, Multi-dir wind angles 0.50
is conducted by the finite element
method. NO
The assumption of mandatory rigid 3) Seismic Information:
diaphragms for the whole building Only overall indicators Seismic Classification class B
Overall calculation considering stair Design seismic group Group Three
stiffness No consideration Seismic Intensity 8(0.2g)
Structural height Class A Site Classification Class Ⅱ
Characteristic Period(s) 0.45
modification factor of Period 1.00
2) Wind Load Information:
计算地震位移时是否考虑周期折减系数对
Surface roughness B 地震作用的影响 YES
Revised basic wind pressure(kN/m2) 0.98 The maximum strong motion factor of
Fundamental period in X direction (s) 0.43 earthquake 0.1600
Fundamental period in Y direction (s) 0.43 The maximum strong motion factor of the
Damping ratio using calculating wind rare earthquake 0.9000
load(%) 2.00 Curve of earthquake influence factor
Wind load effect amplification factor custom NO
for capacity design 1.00 Determining the method of damping
Retain user definition of wind loads NO ratio Unity of the whole building
Considering along-wind resonant YES Structure damping ratio(%) 4.00
Considering cross-wind resonant NO The type of eigenvalues analysis
Consider wind induced torsion User define mode number Subspace iteration
oscillation NO The program automatically determines
Cross wind or torsional wind vibration the number of vibration modes
check YES Sum of quality participation factor 90.00
Wind pressure for comfort Maximum number of modes 0
evaluation(kN/m2) 0.98 Frame seismic classification Level Ⅱ
Structure damping ratio for comfort Shear wall seismic classification Special Grade
evaluation(%) 2.00 Steel-frame seismic classification Level Ⅱ
External pressure factor Seismic classification of details for
External pressure factor subsection seismic design No change
counts 1 Seismic classification of cantilever
beam for seismic design NO
Number of Decrease level of details for seismic
Segments No. top floor X direction Y direction design below design fixed end NO
1 3 1.30 1.30 For the shear wall structure supported
on moment frame, the seismic design YES
-5-
CABR-PKPM
-6-
CABR-PKPM
Calculation based on combined strong limb Beam end negative moment amplitude
Steel tube bundle shear wall model model modulation factor 0.85
Rigidity amplification factor of joist 1.00 Beam end moment amplitude modulation Modulation through primary and secondary beam
Steel tube bundle wall stiffness method supports
modification factor 1.00 Internal force amplification factor of
Shear-weight ratio modification YES beam on live load 1.00
Whether the torsion effect is obvious NO Torque reduction factor of beam 0.40
Dynamic displacement ratio in Transfer member modification factor of
minority axis 0.00 horizontal seismic action effect 1.00
Dynamic displacement ratio in major
axis 0.00
Weak stories modification 7) Design Information:
Determinate weak Story by stiffness Strictly judge according to the anti code and Structure importance factor 1.10
ratio high code Strength ratio of crossed diagonal
Automatically modify weak Story by reinforcement to diagonal diagonal
shear capacity NO reinforcement 1.00
Number of specified weak/soft stories 0 Minimum axial compression ratio used
Weak/soft sorties seismic internal to calculate beams Subject to Flexure 0.15
force amplification factor 1.25 Minimum axial tension ratio used to
Seismic action modification calculate beams Subject to Flexure 0.15
Seismic action modification factor of Reinforcement of frame beam end
the whole building 1.00 considering compression steel bar YES
Beam internal force modification where The Transfinite value of axial
connected to frame strut NO compression ratio of frame part in the
Upper bound of modification factor of structure shall be adopted according
moment frame system 5.00 to the provisions of pure frame
0.2V0 Information structure NO
Internal force modification method Second order effect of bent columns NO
considering two-way earthquake Consider two-way earthquake before adjustment Calculation principle of column
Segment modification method Normative method reinforcement Calculated by single bias
arrange mode min [alpha*V0,beta*Vfmax] Reinforcement method of column subject
alpha 0.25 to biaxial bending and axial force Common way
beta 1.80 Calculation principle of column-span
Segment modification number 1 span ratio Simplified mode (H/2h0)
Adjust starting layer number 1 H=Hn NO
Adjust the ending layer number 3 The bending moment of frame beam is The main beam and secondary beam shall be in
Upper bound of Segment modification controlled by simply supported beam accordance with this clause
factor 2.00 Processing method for main beam to Piecewise calculation
-7-
CABR-PKPM
-8-
CABR-PKPM
-9-
CABR-PKPM
- 10 -
CABR-PKPM
The design values of steel bar strength are shown in the table. When the design of non
yielding under medium and large earthquakes is selected, the program automatically uses
the standard value of material strength for calculation.
- 11 -
CABR-PKPM
1. Load Case
表 5-6 各层的柱、墙面积信息(单位:m^2)
Table 6-1 Load Case Setting
Story No. 楼层面积 柱面积 墙面积 X 向墙面积 Y 向墙面积
Load Case
3 158.70 0.20(0.12%) 0.00(0.00%) 0.00(0.00%) 0.00(0.00%) Load Case NO. Load Case Name
Abbreviation
2 158.25 0.26(0.16%) 0.00(0.00%) 0.00(0.00%) 0.00(0.00%)
1 119.25 0.26(0.21%) 0.00(0.00%) 0.00(0.00%) 0.00(0.00%) Load Case 1 DL Dead Load
Load Case 2 LL Live Load
Live load considering adverse arrangement
Load Case 3 LL2
(negative envelope)
4. Tower and Floor Properties Live load considering adverse arrangement
Load Case 4 LL3
(positive envelope)
Table 5-7 Properties Table
Load Case 5 WX X-direction wind load
Small Load Case 6 WY Wind load in Y direction
Story Transfer SSin Transfer Soft DR is
CEEL SS Part HS Load Case 7 EXY X + y earthquake (bidirectional effect)
No. Story Bottom Story story 1.0.
on Top Load Case 8 EXP X-dir Positive Eccentric Earthquake
3 √ Load Case 9 EXM X-dir Negative Eccentric Earthquake
2 √ √ Load Case 10 EYX Y + X earthquake (bidirectional effect)
1 √ √ √ Load Case 11 EYP Y-dir Positive Eccentric Earthquake
Load Case 12 EYM Y-dir Negative Eccentric Earthquake
X-dir Eccentric Earthquake (Specified
Table 5-8 Component Material Load Case 13 LX
Horizontal Force)
Concrete Y-dir Eccentric Earthquake (Specified
Concrete Column Steel Beam Steel Column Load Case 14 LY
Story Beam Horizontal Force)
No. Concrete X-dir Positive Eccentric Static Earthquake
Concrete Grade Steel Grade Steel Grade Load Case 15 PX
Grade (Specified Horizontal Force)
1-3 C30 C35 Q355 Q355 X-dir Negative Eccentric Static Earthquake
Load Case 16 MX
(Specified Horizontal Force)
Y-dir Positive Eccentric Static Earthquake
Load Case 17 PY
Table 5-9 Concrete Grade and Reinforcement Strength (Specified Horizontal Force)
Y-dir Negative Eccentric Static Earthquake
Concrete Wall Steel Bracing Load Case 18 MY
Story No. (Specified Horizontal Force)
Concrete Grade Steel Grade
Load Case 19 EX X direction earthquake
1-3 C30 Q355 Load Case 20 EY Y-direction earthquake
- 12 -
CABR-PKPM
- 13 -
CABR-PKPM
The total mass due to live load, the total mass due to custom load and the total mass
of the structure are the result of the reduction of live load (1t = 1000kg)
Figure 7-1 Dead load, live load and mass line chart Xstif、Ystif(m): X, Y coordinate value of rigid center
Alf(Degree): The direction of the rigid axis of the layer
Eex、Eey: Eccentricity in X and Y directions
Table 7-2 Stiffness Center and Eccentricity Information of Each Floor
Story No. Xstif Ystif Alf Eex Eey
3 4.33 8.00 0.00 5.84% 4.74%
- 14 -
CABR-PKPM
- 15 -
CABR-PKPM
- 16 -
CABR-PKPM
Ratx1, Raty1 (stiffness ratio 1):the smaller of the ratio of the lateral displacement
stiffness of the tower in the X and Y directions to the lateral rigidity of the
corresponding tower of the upper layer of 70% or the average lateral rigidity of the
upper three layers of 80% (According to the anti-regulation 3.4.3; high-profile 3.5.2-1)
Rat2_min: Limitation by stiffness ratio 2
RJX,RJY: Structural lateral stiffness in global coordinate system
Table 9-2 Stiffness and Stiffness Ratio
Story No. RJX(kN/m) RJY(kN/m) Ratx1 Raty1
3 1.66e+5 27583.72 1.00 1.00
2 1.42e+5 38920.73 1.22 2.02
1 2.75e+5 43349.46 2.78 1.59
The definition of irregular lateral stiffness in article 3.4.3-2 of code for seismic
design is as follows: the lateral stiffness of the floor is less than 70% of the adjacent
upper floor, or less than 80% of the average lateral stiffness of the three adjacent
floors above it; the lateral stiffness ratio of some floors of the structure does not
meet the requirements of the code, see the stiffness ratio 1 in the table below for
details.there is no irregular lateral stiffness of the structure.
- 17 -
CABR-PKPM
Figure9-3 Muti-directional Stiffness Diagram Figure 9-4 Stiffness ratio type 1 line chart
The definition of irregular lateral stiffness in article 3.4.3-2 of code for seismic
design is as follows: the lateral stiffness of the floor is less than 70% of the adjacent
upper floor, or less than 80% of the average lateral stiffness of the three adjacent
floors above it; the lateral stiffness ratio of some floors of the structure does not
meet the requirements of the code, see the stiffness ratio 1 in the table below for
details.there is no irregular lateral stiffness of the structure.
- 18 -
CABR-PKPM
Ratx1, Raty1 (stiffness ratio 1):the smaller of the ratio of the lateral displacement
stiffness of the tower in the X and Y directions to the lateral rigidity of the
corresponding tower of the upper layer of 70% or the average lateral rigidity of the
upper three layers of 80% (According to the anti-regulation 3.4.3; high-profile 3.5.2-1)
Rat2_min: Limitation by stiffness ratio 2
RJX,RJY: Structural lateral stiffness in global coordinate system
Table 9-3 Stiffness and Stiffness Ratio
Story No. RJX(kN/m) RJY(kN/m) Ratx1 Raty1
3 1.57e+5 27741.85 1.00 1.00
2 2.22e+5 36711.52 2.01 1.89
1 3.63e+5 47030.73 2.34 1.83
- 19 -
CABR-PKPM
(X, Y direction)
Table 9-4 Story Lateral Strength and Ratio in Each Floor
Story No. Vx(kN) Vy(kN) Vx/Vxp Vy/Vyp OK or not
3 4876.54 3796.44 1.00 1.00 YES
2 8836.01 4196.65 1.81 1.11 YES
1 7110.09 3613.51 0.80 0.86 YES
《抗规》3.4.4-2 条规定:楼层受载力突变时,薄弱层抗侧力结构的受剪承载力不应小于相邻上
一楼层的 65%。
结构设定的限值是 65.00%。并无楼层承载力突变的情况
Figure 9-7 Shear bearing capacity ratio line chart
- 20 -
CABR-PKPM
表 10-2 结构周期比
Chapter Ⅹ. Seismic Action 第一扭转周期 Vibration model 第一平动周期 Vibration model
周期比
(s) No. (s) No.
1. Period and Model Shape 0.4155 2 0.8741 1 0.48
- 21 -
CABR-PKPM
有蓝色底色标识位置双击可以查看图形
表 10-4 结构周期比
第一扭转周期 Vibration model 第一平动周期 Vibration model
周期比
(s) No. (s) No.
0.2582 4 0.8723 1 0.30
说明:此处计算周期比采用的扭转和平动振型通过平动和扭转因子进行判断,程序无法确定其是
否为整体振型,
因此结果仅供参考.设计人员应通过振型图确定计算周期比所需的第一阶平动振型和扭转振型。
Note: in the figure, blue indicates lateral vibration component and red
indicates torsional vibration component.
- 22 -
CABR-PKPM
Vibration Vibration
EX EY EX EY
model No. model No.
5 0.81% 0.55% 6 1.27% 5.09%
7 0.02% 1.41% 8 0.93% 0.00%
9 15.59% 0.00%
3. Effective Mass Ratio of Each Model Story No. Vx(kN) RSW Coef2 Coef_RSWx
3 299.1 20.70% 1.00 1.00
Table 10-5 Earthquake direction and Effective mass factor of vibration modal 2 459.4 15.19% 1.00 1.00
1 564.5 12.03% 1.00 1.00
Vibration Vibration
EX EY EX EY
model No. model No.
1 0.00% 86.89% 2 15.48% 0.16%
3 0.18% 5.78% 4 65.04% 0.12%
- 23 -
CABR-PKPM
Figure 10-4 Diagram of shear weight ratio under various working conditions of earthquake
Figure 10-3 Floor shear force diagram under various seismic conditions
- 24 -
CABR-PKPM
Table 11-1 Overturning moment and percentage under X-direction static earthquake
condition (unit:kN.m)
Total
Story Frame Short Ordinary
Bracing bending
No. column limb wall wall
moment
3 132.7(8.4%) 0.0(0.0%) 0.0(0.0%) 1452.4(91.6%) 1585.2
2 393.4(9.8%) 0.0(0.0%) 0.0(0.0%) 3626.7(90.2%) 4020.1
1 604.0(8.2%) 0.0(0.0%) 0.0(0.0%) 6746.5(91.8%) 7350.5
Table 11-2 Overturning moment and percentage under Y-direction static vibration
condition (unit:kN.m)
Total
Story Short Ordinary
Frame column Bracing bending
No. limb wall wall
moment
3 969.7(100.0%) 0.0(0.0%) 0.0(0.0%) 0.0(0.0%) 969.7
2 2609.1(100.0%) 0.0(0.0%) 0.0(0.0%) 0.0(0.0%) 2609.1
1 4883.6(100.0%) 0.0(0.0%) 0.0(0.0%) 0.0(0.0%) 4883.6
Figure 10-5 Diagram of adjustment factor of shear weight ratio finally adopted in various
working conditions of earthquake
5. Accidental Eccentric
- 25 -
CABR-PKPM
Figure 11-1 Diagram of overturning moment under X-direction static earthquake Figure 11-2 Diagram of overturning moment under Y-direction static earthquake
Table 11-3 Overturning moment and percentage under X-direction static earthquake
condition (unit:kN.m)
Coordinate
of Total
Story Short Ordinary
resultant Frame column Bracing bending
No. limb wall wall
force moment
point (m)
- 26 -
CABR-PKPM
X Y
3 6.4 7.9 858.8(54.2%) 0.0(0.0%) 0.0(0.0%) 726.4(45.8%) 1585.2
2 6.5 7.2 2349.5(58.4%) 0.0(0.0%) 0.0(0.0%) 1670.6(41.6%) 4020.1
1 6.5 7.3 5790.6(78.8%) 0.0(0.0%) 0.0(0.0%) 1559.8(21.2%) 7350.5
Table 11-4 Overturning moment and percentage under Y-direction static vibration
condition (unit:kN.m)
Coordinate
of
Total
Story resultant Short Ordinary
Frame column Bracing bending
No. force limb wall wall
moment
point (m)
X Y
3 6.4 7.9 920.4(94.9%) 0.0(0.0%) 0.0(0.0%) 49.4(5.1%) 969.7
2 6.5 7.2 2543.9(97.5%) 0.0(0.0%) 0.0(0.0%) 65.2(2.5%) 2609.1
1 6.5 7.3 4588.6(94.0%) 0.0(0.0%) 0.0(0.0%) 295.0(6.0%) 4883.6
- 27 -
CABR-PKPM
Total
Frame Wall and
Story No. shear
column bracing
force
1 32.0( 5.7%) 534.6(94.7%) 564.5
Table 11-6 Shear force and percentage in Y-direction earthquake condition (unit:
kN)
Total
Wall and
Story No. Frame column shear
bracing
force
3 183.0(100.0%) 0.0(0.0%) 183.0
2 309.3(100.0%) 0.0(0.0%) 309.3
1 385.5(100.0%) 0.0(0.0%) 385.5
Table 11-5 Shear force and percentage in X-direction earthquake condition (unit:
kN)
Total
Frame Wall and
Story No. shear
column bracing
force
3 24.9( 8.3%) 274.3(91.7%) 299.1
2 46.9(10.2%) 421.3(91.7%) 459.4
- 28 -
CABR-PKPM
Figure 11-5 Shear force diagram under X-direction earthquake Figure 11-6 Shear force diagram under Y-direction earthquake
4. Frame 0.2vo(0.25vo) adjustment factor for single tower and multi tower
根据《抗规》8.2.3-3 条规定:钢框架-支撑结构的框架部分按刚度分配计算得到的地震层剪力
应乘以调整系数,达到不小于结构底部总地震剪力的 25%和框架部分计算最大层剪力 1.8 倍二
者的较小值。
The adjustment of each floor of the structure is shown in the table below:
- 29 -
CABR-PKPM
The factor of VO in 0.2vo adjustment: alpha = 0.25 Table 11-9 Frame shear force of each tower under Y-direction seismic condition
The factor of Vmax in 0.2vo adjustment: beta = 1.80
(KN)
0.2Vo adjustment mode: Min{alpha*Vo,beta*Vmax} Story No. Vc_p alpha*Vo beta*Vmax Vc_f
3 183.0 96.4 693.9 182.97
0.2vo adjustment upper Transfinite: KQ_L = 2.00
2 309.3 96.4 693.9 309.32
0.2vo adjustment segment number: VSEG = 1 1 385.5 96.4 693.9 385.51
Position of the first paragraph: 1-3floor
Table 11-10 Adjustment factor of frame shear force of each tower under
Symbol description: Y-direction earthquake
Vc_p : Frame shear force of this floor before adjustment Story
Coef1 Coef2 C02v_c C02v_w
No.
Vc_f : Adjusted frame shear force of this floor
1-3 1.00 1.00 1.00
Coef1 : User defined 0.2vo adjustment factor
Coef2 : Calculation value of 0.2vo adjustment factor of the column in this floor
C02v_c : The final value of 0.2vo adjustment factor of this layer column (if
user-defined value is adopted)
C02v_w : Shear adjustment factor of this floor wall
Table 11-7 Frame shear force of each tower under X-direction earthquake condition
(KN)
Story No. Vc_p alpha*Vo beta*Vmax Vc_f
3 24.9 141.1 84.3 49.80
2 46.9 141.1 84.3 84.34
1 32.0 141.1 84.3 64.07
Table 11-8 Adjustment factor of frame shear force of each tower under X-direction
earthquake
Story
Coef1 Coef2 C02v_c C02v_w
No.
3 2.00 2.00 1.00
2 1.80 1.80 1.00
1 2.00 2.00 1.00
- 30 -
CABR-PKPM
Under all working conditions, the displacement ratio and inter story displacement ratio
meet the requirements of the code.
Maximum floor displacement of the whole building under this condition= 6.09(occur
on floor 3 tower 1)
Maximum displacement ratio of the whole building under this condition = 1.26 (occur
on floor 2 tower 1)
Maximum story to floor displacement ratio of the whole building under this condition=
1.28(occur on floor 2 tower 1)
有蓝色底色标识位置双击可以查看图形
Figure 11-7 0.2v0 adjustment factor diagram Table 12-2 Displacement of X-direction negative eccentric static earthquake
(specified horizontal force)
Maximum Maximum Average Story
Chapter Ⅻ. Deformation Story
displacement(Node
Average
Story inter-floor
Mass
drift
No. Displacement ratio
No.) drift displacement ratio
1. Floor Displacement Summary 3 5.12(173) 5.06 1.88 1.77 1.01 1.06
2 3.36(134) 3.30 1.97 1.88 1.02 1.05
Chapter 〇. Deformation
1 1.45(25) 1.42 1.45 1.42 1.02 1.02
Maximum floor displacement of the whole building under this condition= 5.12(occur
《抗规》3.4.3-1 条对于扭转不规则的定义为:在规定的水平力作用下,楼层的最大弹性水平 on floor 3 tower 1)
位移(或层间位移),大于该楼层两端弹性水平位移(或层间位移)平均值的 1.2 倍。结构设定的
Maximum displacement ratio of the whole building under this condition = 1.02 (occur
判断扭转不规则的位移比为 1.20,位移比的限值为 1.50,结构不属于扭转不规则。
on floor 1 tower 1)
- 31 -
CABR-PKPM
Maximum story to floor displacement ratio of the whole building under this condition= 1.04(occur on floor 2 tower 1)
1.06(occur on floor 3 tower 1)
有蓝色底色标识位置双击可以查看图形
有蓝色底色标识位置双击可以查看图形
- 32 -
CABR-PKPM
- 33 -
CABR-PKPM
- 34 -
CABR-PKPM
Figure12-3 Diagram of average inter story displacement Figure12-4 Diagram of maximum inter story displacement
- 35 -
CABR-PKPM
Figure 12-5 Displacement ratio diagram Figure 12-6 Diagram of displacement ratio between floors
- 36 -
CABR-PKPM
2. Overall Stability
This part of v3.1.1 and later uses more accurate calculation formula of the ratio of
rigidity to weight, which is different from the previous version. Please refer to the
user manual for details.
Table 13-2 Checking rigid weight ratio based on seismic action
Load Checking Checking
case formula value
EX EJD/GH^2 51.25
EY EJD/GH^2 7.22
- 37 -
CABR-PKPM
factor (0.02, 1-storey, 1-Tower) is not greater than 0.25, which can pass the stability
calculation of steel structure standard GB 50017-2017 5.1.6.
1. Floor Diagram
- 38 -
HW300X300[ 39]
( 11) ( 12) ( 13)
HW300X300[ 39]
HW300X300[ 39]
( 92) ( 93) ( 94) ( 95) ( 96)
( 2)
上
( 14)
( 4)
HM294X200[ 39] HM294X200[ 39]上 HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
[ 14a[ 32]
[ 14a[ 32]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 87)
( 88)
( 89)
( 90)
( 91)
HN400X200[ 39]
( 80) ( 81) ( 82) ( 83) ( 84) ( 85)
( 86)
HN250X125[
HN39]
250X125[ 39] HN250X125[ 39] HN350X175[ 39] HN350X175[ 39] HN350X175[ 39]
[ 14a[ 32]
[ 14a[ 32]
( 75)
( 76)
( 77)
( 78)
( 79)
39] 39]
588X300[ 39]
( 70) ( 71) ( 72) ( 73) ( 74)
M588X300[
HN250X125[ 39] HN250X125[ 39] HN300X150[ 39] HN300X150[ 39] HN300X150[ 39]
( 69)
( 67)
HM588X300[
39]
39]
H39]
HN400X200[ 39]
HM
HM
( 66)
( 64)
M588X300[
340X250[
588X300[
HM588X300[ 39]
( 63)
HN250X125[ 39]
( 60)
( 62)
39]
39]
HM
HM
HM244X175[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]HM340X250[
[ 14a[ 32]
HN250X125[ 39] HN300X150[ 39] HN300X150[ 39]
( 53)
( 54)
( 55)
( 56)
( 7) ( 8) ( 9)
HW300X300[ 39]
( 49) ( 50) ( 51) ( 52)
( 10)
HM294X200[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
[ 14a[ 32]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 45)
( 46)
( 47)
( 48)
HN400X200[ 39]
( 41) ( 42) ( 43)
( 44)
HN250X125[ 39] HN350X175[ 39] HN350X175[ 39]
[ 14a[ 32]
( 37)
( 38)
( 39)
( 40)
39]
39]
( 33) ( 34) ( 35) ( 36)
HM588X300[
HM588X300[
[ 14a[ 32]
HN250X125[ 39] HN300X150[ 39] HN300X150[ 39] HN300X150[ 39]
( 30)
( 31)
( 32)
39]
39]
( 28) ( 29)
( 27)
HM588X300[
HM588X300[
HN400X200[ 39]
HM588X300[ 39] HM588X300[ 39]
( 25)
( 26)
( 19) ( 20) ( 21) ( 22) ( 23)
( 24)
HM244X175[ 39] HM588X300[ 39]
HM588X300[ 39]
HN250X125[ 39] HN300X150[ 39] HN300X150[ 39] HN300X150[ 39]
HN300X150[ 39]
[ 14a[ 32]
[ 14a[ 32]
( 18) 32]
( 13)
( 14)
( 15)
( 16)
( 17)
[ 14a[
HW300X300[ 39]
( 3) ( 4) ( 5)
HW300X300[ 39]
HW300X300[ 39]
( 3)
上
( 6)
( 1)
上HM340X250[ 39]
HM294X200[ 39]
HM294X200[ 39]
HM294X200[ 39] HM340X250[ 39] HM340X250[ 39]
HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 5)
( 6)
( 3)
( 4)
( 2)
HW300X300[ 39]
HW300X300[ 39]
HN200X100[ 39]
( 1)
( 1)
( 2)
HM340X250[ 39]
HW300X300[ 39]
HW300X300[ 39]
( 113) ( 114) ( 115) ( 116) ( 117)
( 1)
上
HM440X300[ 39]
[ 14a[ 32]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 107)
( 108)
( 109)
( 110)
( 111)
( 112)
39]
39]
( 101) ( 102) ( 103) ( 104) ( 105) ( 106)
HM440X300[
HM340X250[
( 100)
HN300X150[ 39] HN250X125[ 39] HM340X250[H
39]
M340X250[ 39] HM340X250[ 39] HN300X150[ 39]
( 99)
39]
39]
( 96)
( 94)
( 95)
( 97)
( 98)
M440X300[
HM340X250[
HN250X125[ 39]
( 92)
39]
440X300[ H
HN200X100[ 39]
HN300X150[ 39] HN250X125[ 39] HN250X125[ 39] HM340X250[H
39]
M340X250[
HM340X250[
39] 39] HM340X250[ 39] HN350X175[ 39]
39] HM340X250[
[ 14a[ 32]
( 81)
( 82)
( 83)
( 78)
( 79)
( 80)
39]
( 76)
( 77)
39]
39]
HM340X250[
HM
39] HM
HM440X300[
HM440X300[
( 73) ( 74) ( 75)
( 72)
( 70) ( 71)
( 69)
( 68)
HN300X150[ 39]HN250X125[ H
39]
N250X125[ 39] HN250X125[ 39]
39]
( 65) ( 66) ( 67) HN300X150[ 39]
[ 14a[ 32]
HM244X175[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[
( 64)
( 61)
( 62)
( 63)
( 59)
( 60)
( 7) ( 8) ( 9)
HW300X300[ 39]
( 53) ( 54) ( 55) ( 56) ( 57) ( 58)
( 10)
HM294X200[ 39]HM294X200[ 39] HM294X200[ 39] HM390X300[ 39] HM390X300[ 39] HM340X250[ 39]
[ 14a[ 32]
HW400X400[ 39]
( 49) HW400X400[ 39] HW400X400[ 39]
( 50)
( 51)
( 52)
HN400X200[ 39]
( 42) ( 43) ( 44) ( 45) ( 46) ( 47)
( 48)
HN250X125[ 39]
HN250X125[ 39] HN250X125[ 39] HN350X175[ 39] HN350X175[ 39]HN350X175[ 39]
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
( 36)
( 37)
( 38)
( 39)
( 40)
( 41)
( 29) ( 30) ( 31) ( 32) ( 33) ( 34) ( 35)
HN250X125[ 39]
HN250X125[ 39] HN250X125[ 39] HN350X175[ 39] HN350X175[ 39] HN350X175[ 39] HN300X150[ 39]
39] HM440X300[
[ 14a[ 32]
( 26)
( 27)
( 28)
( 25)
39]
HN400X200[ 39]
HM440X300[ ( 22) ( 23) ( 24)
( 21)
( 18) ( 19)
( 20)
HN350X175[ 39] HN350X175[ 39] HN350X175[ 39]
HN250X125[ 39] HN250X125[ 39]
( 17) 32]
HM244X175[ 39] HM440X300[
[ 14a[ 32]
( 16)
[ 14a[
( 13)
( 14)
( 15)
HW300X300[ 39]
( 3) ( 4) ( 5)
HW300X300[ 39]
HW300X300[ 39]
( 7) ( 8) ( 9) ( 2) 上 ( 10) ( 11) ( 12)
( 6)
( 4)
上
HN300X150[ 39]
HN300X150[ 39]
HM294X200[ 39] HM294X200[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 5)
( 6)
( 3)
( 4)
( 2)
HW300X300[ 39]
HW300X300[ 39]
HN200X100[ 39]
( 1)
( 1)
( 2)
HM340X250[ 39]
- 40 -
HW250X250[ 39]
( 7) ( 8) ( 9)
HW250X250[ 39]
( 107) ( 108) ( 109) ( 110)
( 1)
上
[ 14a[ 32]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 102)
( 103)
( 104)
( 105)
( 106)
( 96) ( 97) ( 98) ( 99) ( 100) ( 101)
HN200X100[ 39] HN250X125[ 39] HN250X125[ 39] HN350X175[ H
39]
N350X175[ 39] HN350X175[ 39]
[ 14a[ 32]
[ 14a[ 32]
( 90)
( 91)
( 92)
( 93)
( 94)
( 95)
250X125[ 39]
( 84) ( 85) ( 86) ( 87) ( 88) ( 89)
HN200X100[ 39] HN250X125[ 39] HN250X125[ 39] HN350X175[ 39] HN350X175[ 39] HN350X175[ 39]
( 79)
( 80)
( 81)
( 82)
( 83)
39]
300X150[ 39]
HN
( 72) ( 73) ( 74) ( 75) ( 76) ( 77) ( 78)
300X150[
HN250X125[ 39]
HN200X100[ 39] HM340X250[ 39] HM340X250[ 39] HN350X175[ 39] HN350X175[ 39]HN350X175[H39]
N350X175[ 39]
( 70)
( 71)
HN39]
HN39]
[ 14a[ 32]
( 69)
( 63)
( 64)
( 65)
( 66)
( 67)
( 68)
HN300X150[
HN300X150[
HN300X150[ 39]
( 61)
( 62)
( 4) ( 5) ( 6)
( 54) ( 55) ( 56) ( 57) ( 58) ( 59) ( 60)
HN300X150[ 39] HN300X150[ 39] HN300X150[ 39] HN300X150[ 39]
HN250X125[ 39]
( 50)
( 51)
( 52)
( 53)
( 45) ( 46) ( 47) ( 48)
HN200X100[ 39] HM340X250[ 39] HM340X250[ 39] HN350X175[ 39]
( 41)
( 42)
( 43)
( 44)
( 38) ( 39) ( 40)
HN200X100[ 39] HN250X125[ 39] HN350X175[ 39]
( 34)
( 35)
( 36)
( 37)
( 30) ( 31) ( 32) ( 33)
HN200X100[ 39] HN250X125[ 39] HN350X175[ 39] HN350X175[ 39]
[ 14a[ 32]
( 25)
( 26)
( 27)
( 28)
( 29)
39] 39]
39] 39]
HW250X250[ 39]
( 1) ( 2) ( 3)
244X175[ 39]
HN250X125[
HN250X125[
244X175[ 39]
HW250X250[ 39]
( 18) ( 19) ( 20) ( 21) ( 22) ( 23) ( 24)上
( 2)
( 11) ( 16)
( 12) ( 17)
HN300X150[ 39]
HM244X175[ 39]
( 4)
HM294X200[ 39] HM294X200[ 39] 上 HM340X250[
HM340X250[ 39] 39]
HM340X250[ 39] ( 15) HM340X250[ 39] HM340X250[ 39]
HN250X125[
HN250X125[
( 13)
( 14)
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
HN250X125[ 39]
39]
39]
( 10)
HM
HM
( 9)
( 6) ( 7) ( 8)
HM244X175[
HM244X175[
HN350X175[ 39] HN350X175[ 39] HN350X175[ 39]
( 4)
( 5)
( 1) ( 2) ( 3)
HN250X125[ 39] HN250X125[ 39] HN250X125[ 39]
- 41 -
2. Loads Diagram
上 DL: 1*8. 00
DL: 4*9. 00*4. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 4*320. 00*2. 00 [ 0. 8]
DL: 4*17. 00*1. [50
0. 8]
DL: 1. 00
4*10.5000*1. 00
DL: 1. 00 DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 LL: 3. 50
DL:00*0.
[ 0. 8] [ 0. 8] [ 0. 8] DL: 1* 8. 00
DL: 4* 9. 00* 4. 00
DL: 4*10.
DL: 1. 00 DL: 1. 00
DL: 4*320. 00*2. 00 LL: 3. 50 LL: 3. 50
DL: 1. 00 [ 0. 8] [ 0. 8]
LL: 3. 50
[ 0. 8] DL: 1. 00
LL: 3. 50
上
DL: 1. 00
LL: 3. 50
[ 0. 8]
DL: 1*8. 00
DL: 4*9. 00*4. 00
第1层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
- 42 -
DL: 4*18. 00*0. 56
DL: 4*36. 00*1. 16
DL: 4*18. 00*1. 74
DL: 4*18. 00*2. 20
上 DL: 4*18. 00*2. 88
DL: 4*36. 00*3. 72
DL: 1. 00
LL: 3. 50
DL: 1. 00 DL: 1. 00 [ 0. 8] DL: 1. 00 DL: 1. 00
LL: 5. 00 LL: 3. 50 LL: 3. 50 LL: 3. 50
[ 0. 8] [ 0. 8] DL: 1. 00 [ 0. 8] [ 0. 8]
LL: 3. 50
上
DL: 1*6. 00
DL: 1. 00
DL: 4*18. 00*0. 56
LL: 3. 50
DL: 4*36. 00*1. 16
[ 0. 8]
DL: 4*18. 00*1. 74
DL: 4*18. 00*2. 20
DL: 4*18. 00*2. 88
DL: 4*36. 00*3. 72
第2层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
- 43 -
上
DL: 1. 00
第3层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
- 44 -
3. Reinforcements Diagram
( 0. 06)
( 0. 06) ( 0. 18) ( 0. 18)
0. 19- 0. 00- 0. 08 0. 22- 0. 00- 0. 09 0. 11- 0. 00- 0. 06 0. 12- 0. 00- 0. 05 上 0. 18- 0. 21- 0. 11
0. 33- 0. 00- 0. 08
0. 33- 0. 00- 0. 08
0. 49
0. 23
0. 16
0. 18 0. 22
CXB
0. 20
0. 19
0. 41
0. 50
0. 23
0. 17
0. 21 0. 25 0. 26
0. 22- 0. 23- 0. 07
0. 20- 0. 00-
0. 0.
28-110. 00- 0. 05
0. 29- 0. 00- 0. 08 0. 28- 0. 00- 0. 09 0. 30- 0. 00- 0. 06 0. 18- 0. 00- 0. 10
0. 31- 0. 00- 0. 07
0. 32- 0. 00- 0. 08
0. 14- 0. 00- 0. 08 0. 19- 0. 00- 0. 06 0. 34- 0. 00- 0. 09 0. 21- 0. 00- 0. 10 0. 26- 0. 46- 0. 13
150. 00- 0. 0.
390. 37
0. 26- 0. 26- 0. 10
33-
0.0.22-
00-0.0.00-
0.0.22-
0. 60- 0. 00- 0. 31
0. 34- 0. 00- 0. 11
330. 00-
240. 00-
0.0.33-
48
0823- 0. 00- 0. 06
2853- 0. 00-0.0.22-
0.0.26-
0.0.32-
0. 34- 0. 00- 0. 11 0. 29- 0. 00- 0. 08 0. 18- 0. 00- 0. 09
1754- 0. 00-
3667- 0. 00-
( 0. 08)
( 0. 11) ( 0. 27) ( 0. 19)
0. 14- 0. 00- 0. 06 0. 09- 0. 00- 0. 07 0. 14- 0. 00- 0. 12 0. 14- 0. 14- 0. 11
0. 45 0. 70 0. 62
0. 12- 0. 00- 0. 060. 48- 0. 00- 0. 170. 23- 0. 00- 0. 110. 20- 0. 00- 0. 120. 49- 0. 00- 0. 0.
CXB
0. 22
0. 20
0. 43
0. 26 0. 42 0. 33
0. 22- 0. 22- 0. 08
0. 19- 0. 00- 0. 07 0. 28- 0. 00- 0. 08 0. 19- 0. 00- 0. 11
2900- 0. 25
0. 10- 0. 00- 0. 06
2200- 0. 15
0. 19- 0. 00- 0. 07 0. 35- 0. 00- 0. 09 0. 25- 0. 00- 0. 12 0. 26- 0. 46- 0. 13
0. 0.
0. 0.
0. 60- 0. 00- 0. 30 0. 17- 0. 00- 0. 17
45-
31-
0. 16- 0. 16- 0. 07
00-
00-
46- 0. 0.
31- 0. 0.
0. 19- 0. 00- 0. 07 0. 31- 0. 00- 0. 12 0. 45- 0. 00- 0. 06 0. 44- 0. 00- 0.0.10
09- 0. 00- 0. 13
0. 38
0. 33- 0. 00- 0. 08
0. 33- 0. 00- 0. 08
0. 29- 0. 00- 0. 07
0. 28
0. 12- 0. 00- 0. 060. 55- 0. 00- 0.
( 0. 07)
( 0. 07) ( 0. 21) ( 0. 20)
0. 23- 0. 00- 0. 09 0. 10- 0. 00- 0. 06 0. 08- 0. 00- 0. 02 0. 09- 0. 00- 0.0.04
13- 0.
上00- 0. 08 0. 20- 0. 23- 0. 12
0. 37 0. 58 0. 54
上 0. 28
0. 31- 0. 30- 0. 19
0. 54
0. 25
0. 22
0. 18 0. 25
CXB
0. 19
0. 18
0. 40
0. 54
0. 25
0. 22
0. 21 0. 33 0. 29
0. 17- 0. 00- 0. 05
( 0. 08)
( 0. 07)
0. 44- 0. 45- 0. 21
CXB
0. 22
0. 25
0. 36
CXB
0. 23
0. 29
0. 44
第 1 层混凝土构件配筋及钢构件应力比、下翼缘稳定验算应力简图( 单位: cm*cm)
本层: 层高 = 5900 ( mm) 梁总数 = 96 柱总数 = 18 支撑总数 = 4
墙总数 = 0 墙柱总数 = 0 墙梁总数 = 0
钢号: 梁 Q355 柱( 含支撑) Q355/ Q235
( DPL代表大偏拉, XPL代表小偏拉, PL代表大\ 小偏拉并存)
超限类别: CXB - - - 长细比
图 15-7 1 层配筋简图 Floor 1 Steel structure stress ratio
- 45 -
( 0. 04)
( 0. 04) ( 0. 09) ( 0. 10)
0. 31- 0. 00- 0. 12 0. 25- 0. 00- 0. 10 0. 02- 0. 00- 0. 03 0. 14- 0. 00- 0. 06 上 0. 32- 0. 00- 0. 32
0. 27- 0. 00- 0. 090. 36- 0. 00- 0. 040. 36- 0. 00- 0. 040. 27- 0. 00- 0. 09
53- 0. 00- 0. 30
0. 35- 0. 00- 0. 06
0. 23- 0. 00- 0. 140. 22- 0. 00- 0. 080. 22- 0. 00- 0. 050. 17- 0. 00- 0. 11
0. 22 0. 34 0. 43
上 0. 13
0. 34
0. 16
0. 12
0. 13 0. 19
CXB
0. 24
0. 28
0. 47
0. 33
0. 16
0. 11
0. 14 0. 15 0. 24
CXB
0. 18
0500- 0. 05
0. 05- 0. 00- 0. 03 0. 19- 0. 00- 0. 07 0. 09- 0. 00-0.
0. 23-
10 0. 00- 0. 08 0. 23- 0. 00- 0. 08 0. 21- 0. 00- 0. 07
1300- 0.
0. 0.
0. 0.
0. 04- 0. 00- 0. 02
25-
05-
00-
00-
18 0. 0.
0. 05- 0. 0.
0. 05- 0. 00- 0. 03 0. 27- 0. 00- 0. 08 0. 27- 0. 00- 0. 090. 28- 0. 00-0.
0. 32-
12
0. 33-
0. 00-
0. 00-
0. 08
0. 03 0. 33- 0. 00- 0. 15 0. 24- 0. 00- 0. 10
0. 25-
0. 29- 0. 00- 0. 08
0. 17- 0. 00- 0. 08
0. 17- 0. 00- 0. 08
200. 00-0.
0. 0.
18-
22-
22-
0. 0.
00-
0. 0.
0. 21- 0. 00- 0. 27-
12 0. 00- 0. 04
0. 26- 0. 00- 0. 09
0. 0.
0. 00-
0. 05- 0. 00- 0. 03 0. 21- 0. 00- 0. 07
3000-
0. 24- 0. 00- 0. 09
0. 22
0. 30
0. 29- 0. 00- 0.
0. 11
33- 0. 00- 0. 04 0. 33- 0. 00- 0. 09
0. 18-
0. 0.
0. 20-
21-
0. 12- 0. 00- 0. 060. 45- 0. 00- 0. 180. 17- 0. 00- 0. 110. 19- 0. 00- 0. 090. 44- 0. 00- 0. 190. 48- 0. 00-
0. 52- 0. 00-
00-
0. 52- 0. 0.
( 0. 05)
( 0. 09) ( 0. 16) ( 0. 11)
0. 31- 0. 00- 0. 12
0. 20- 0. 00- 0. 11 0. 12- 0. 00- 0. 07 0. 06- 0. 00- 0. 05 0. 20- 0. 00- 0. 10 0. 30- 0. 00- 0. 32
0. 22- 0. 00- 0. 09
CXB
0. 23
0. 28
0. 49
0. 16 0. 28 0. 27
0. 19- 0. 19- 0. 06
0. 27- 0. 00- 0. 15
35- 0. 00- 0. 05
0. 35- 0. 00- 0. 11 0. 32- 0. 00- 0. 09 0. 32- 0. 00- 0. 0.
0424- 0. 00- 0. 12
0. 60- 0. 00- 0. 12
0. 19- 0. 00- 0. 09
0. 71- 0. 00- 0. 14
0. 19- 0. 00- 0. 11
25- 0. 00- 0. 04
0. 23- 0. 00- 0. 08 0. 27- 0. 00- 0. 09 0. 30- 0. 00- 0. 05 0. 22- 0. 00- 0. 11 0. 18- 0. 32- 0. 07
1800- 0. 14
0. 31- 0. 00- 0. 07
0. 10- 0. 11- 0. 03
00- 0. 0.
20-
0. 28- 0. 00- 0. 09 0. 29- 0. 00- 0. 07 0. 08- 0. 00- 0. 10
0. 0.
0. 17- 0. 00- 0. 10 0. 22- 0. 00- 0. 07
0. 32- 0. 00- 0. 08
0. 35- 0. 00- 0. 06
0. 24
0. 20-
0. 12- 0. 00- 0. 060. 49- 0. 00-
( 0. 03)
( 0. 05) ( 0. 09) ( 0. 09)
0. 23- 0. 00- 0. 11 0. 21- 0. 00- 0. 09 0. 03- 0. 00- 0. 03 上 0. 11- 0. 00- 0. 040. 15- 0. 00- 0. 09 0. 30- 0. 33- 0. 30
0. 20 0. 34 0. 46
上
0. 53- 0. 56- 0. 21
0. 25- 0. 26- 0. 10
0. 24
0. 13
0. 11
0. 12 0. 14 0. 19
CXB
0. 17
0. 24
0. 41
0. 23
0. 13
0. 11
0. 13 0. 17 0. 25
0. 17- 0. 00- 0. 05
( 0. 05)
( 0. 04)
0. 41- 0. 45- 0. 32
CXB
0. 24
0. 40
0. 50
CXB
0. 25
0. 42
0. 53
第 2 层混凝土构件配筋及钢构件应力比、下翼缘稳定验算应力简图( 单位: cm*cm)
本层: 层高 = 5300 ( mm) 梁总数 = 117 柱总数 = 18 支撑总数 = 4
墙总数 = 0 墙柱总数 = 0 墙梁总数 = 0
钢号: 梁 Q355 柱( 含支撑) Q355/ Q235
( DPL代表大偏拉, XPL代表小偏拉, PL代表大\ 小偏拉并存)
超限类别: CXB - - - 长细比
- 46 -
( 0. 02) ( 0. 04) ( 0. 02)
0. 24- 0. 00- 0. 09 0. 18- 0. 00- 0. 07 0. 06- 0. 00- 0. 05 0. 06- 0. 00- 0. 05 上
0. 35- 0. 00- 0. 07
CXB
0. 26
0. 11
0. 07
0. 11 上 0. 15 0. 11
CXB
0. 24
0. 10
0. 06
0. 15 0. 19 0. 14
CXB
0. 35- 0. 00- 0. 07
0. 34- 0. 00- 0. 07
0. 23- 0. 00- 0. 070. 27- 0. 00- 0. 03
050. 00- 0. 01
060. 00- 0. 05
0.0.01-
0. 09- 0. 00- 0. 04 0. 73- 0. 00- 0. 22 0. 73- 0. 00- 0. 51 0. 37- 0. 00- 0. 10 0. 37- 0. 00- 0. 03
0. 33- 0. 00-0.0.11-
090. 00- 0. 12
060. 00-
0. 04- 0. 00- 0. 02
0. 35- 0. 00- 0. 08
0. 04- 0. 00- 0. 03
08-
08-
0. 0.
0. 0.
0. 08- 0. 00-
0. 08- 0. 00-
( 0. 06) ( 0. 12) ( 0. 04)
0. 47- 0. 00- 0. 17 0. 27- 0. 00- 0. 11 0. 13- 0. 00- 0. 07 0. 24- 0. 00- 0. 16 0. 24- 0. 00- 0. 07
0. 18- 0. 00-0.0.21-
130. 00- 0. 20
0. 30 0. 48 0. 47
0. 03- 0. 00- 0. 02
0. 61- 0. 00- 0. 16
06 0. 10
06 0. 10
( 0. 03) ( 0. 06) ( 0. 04)
0. 31- 0. 00- 0. 12 0. 22- 0. 00- 0. 09 0. 13-
0.0.04-
00-0.0.00-
170.0.0809- 0. 00- 0. 03 0. 09- 0. 00- 0. 040. 09- 0. 00-
上 0. 11
070. 00- 0. 0.
040. 00- 0. 0.
0. 00-
0. 00-
0. 23 0. 36 0. 23
上 0. 17
CXB
0. 34
0. 14
0. 10
0. 43- 0. 00- 0. 14
00-0.
00-0.
0. 13 0. 11
0. 10-
0. 10-
CXB
0. 32
0. 14
0. 09
0. 16 0. 21 0. 14
71-
83-
0. 10-0.
0. 10-0.
0. 21- 0. 00- 0. 14 0. 40- 0. 00- 0. 10 0. 21- 0. 00- 0. 14
0. 0.
0. 0.
0. 11- 0. 00-
0. 06- 0. 00-
0. 17- 0. 00- 0. 05 0. 17- 0. 00- 0. 06 0. 17- 0. 00- 0. 04
- 47 -
4. Diagram of Beam Elastic Deflection
上
0. 18
0. 18 上 0. 58 0. 63 0. 25
0. 76
0. 76
0. 89
1. 31
0. 81
1. 43
2.2.4242 2. 69
0. 72
0. 74
4. 80 5. 34
1.1.5151
2. 14
1.1.3029
1. 07
2. 15
0. 98 1. 62
3. 61 3. 38
93
1. 12
1. 23
1.1.85
7. 14
2. 84
0. 69
1. 03
0. 57
5. 61
0. 29
2. 84 3. 07
6. 02
0. 10 0. 98 0. 41 0. 15
1. 61
0. 36
1. 05
0. 77
1. 56
2. 64
2. 49
5. 09
0. 70
3638 2. 27
2. 01
1. 561. 591. 55
0. 99
1. 56
3. 87 3. 38
2. 2.
7. 37
2. 56
0. 43
1. 78
1. 15
5. 66
1. 56 1. 51
0. 76
0. 77
0. 65
5. 56
9. 33 8. 86
上
0. 07 上 0. 36 0. 69 0. 64 0. 06 0. 22
- 0. 18
- 0. 10
- 1. 00
0. 46
1. 74
0. 30
- 48 -
- 0. 15 - 0. 03 - 0. 48 上
上
2. 05
3. 06
0. 80
5. 28
0. 99
1. 26
1. 25
1. 99
0. 10
1. 57 1. 41
2. 45
1. 79
0. 07
3. 96 4. 30
0. 11
7576
95
7. 41
1. 66
1.1.94
1. 89
2. 2.
0. 10
2. 16
2. 28 2. 48
0. 59
5. 135. 93
0. 50
0. 50
6. 21 6. 56
07
0. 821. 21
5. 28
0.1.99
1. 04
1. 66
0. 81
0. 75
0. 10
2. 061. 97
2. 45
0. 67
4. 81
5. 77 6. 04
- 0. 08 - 0. 14 - 0. 35
0. 17
2. 66 2. 05
0. 54
- 0. 33
0. 80
0. 68
0. 65
1. 96
3. 293. 03 3. 50
0. 49
1. 71
1. 31
5. 925. 87
2323
- 0. 06
1. 07
1. 12
1. 1.
1. 34 2. 22 2. 03 3. 05 2. 29
0. 60
4. 82 5. 53
65
0. 76
0. 64
0.0.59
1. 17 1. 31
1. 93
0. 87
0. 81
4. 75 5. 38
上 - 0. 33 - 0. 22
0. 18 0. 33 0. 02 上
2. 01
- 0. 06
- 0. 02
0. 56
0. 37
1. 75
2. 77
- 49 -
- 0. 25 上
上 0. 67 1. 02
2. 66
0. 82
4. 02
1. 67
2. 32
1. 22
0. 31
2. 47 1. 68 1. 98
0. 84
0. 79
6. 13 6. 37
5. 65
2.2.7777
3.3.7978
1. 89
0. 29 1. 16 0. 75
2. 42 2. 20
4. 59
2. 12
2. 99
1. 82
1. 39
7. 92
0. 30
1. 97
1. 28
0.0.1817
4. 02 3. 54 4. 10
0. 08
1. 22
5. 39
0. 03
- 0. 65 - 0. 42
0. 80
2. 84 2. 09
0. 06
5. 34
4. 42
2. 67
0. 09
2. 17
0. 31
4. 02 3. 54 4. 28
0. 14
3. 35
7577
5. 66
0. 14
3. 29
2.2.
0. 30
1. 48
4. 60
4. 03
1. 65
1. 54
0. 31
1. 57 1. 25
- 0. 12
1. 40
6. 07
- 0. 41 上
上 0. 35 08
08
0.0.08 0. 66
0.0.08
0. 99 1. 71
1. 70
3. 61
0. 03
2. 76
1. 33
- 0. 01
- 0. 02
6. 02
- 0. 22 - 1. 07 3. 39 3. 44
2. 49
7. 87
4. 15
- 50 -
CABR-PKPM
-1-
CABR-PKPM
3. Reinforcements Diagram............................................................................................................................. 52
4. Diagram of Beam Elastic Deflection ..................................................................................................... 59
目 录
Chapter Ⅰ. General Provisions ............................................................................................................................. 3
Chapter Ⅱ. Software Information ......................................................................................................................... 3
Chapter Ⅲ. General information of the project ............................................................................................. 3
Chapter Ⅳ. Structure Evaluation Summary ......................................................................................................... 4
Chapter Ⅴ. Structural Model Overview ............................................................................................................... 5
1. System General Information ....................................................................................................................... 5
2. Floor Information ....................................................................................................................................... 16
3. Dimensions of Each Floor ......................................................................................................................... 16
4. Tower and Floor Properties ..................................................................................................................... 17
Chapter Ⅵ. Load case and Combinations ........................................................................................................... 18
1. Load Case ....................................................................................................................................................... 18
2. Load Case Information ............................................................................................................................... 18
3. Basic Combination factor of Internal Forces in Elements ........................................................... 19
Chapter Ⅶ. Mass Information ............................................................................................................................... 19
1. Mass Distribution ....................................................................................................................................... 20
2. Rigid Center and Eccentricity Information of Each Floor ........................................................... 20
Chapter Ⅷ. Load Information ............................................................................................................................... 21
1. Wind Load Information ............................................................................................................................... 21
Chapter Ⅸ. Vertical Irregularity ..................................................................................................................... 22
1. Story Lateral Stiffness ........................................................................................................................... 22
2. Stiffness(Ratio of Floor Shear Force and Displacement) ............................................................. 22
3. Shear Bearing Capacity of Each Floor ................................................................................................. 23
4. Weak Story Modified Factor ..................................................................................................................... 23
Chapter Ⅹ. Seismic Action ................................................................................................................................... 24
1. Period and Model Shape ............................................................................................................................. 24
2. Period and Model Shape ............................................................................................................................. 26
3. Effective Mass Ratio of Each Model ..................................................................................................... 26
4. Minimum Seismic Force ............................................................................................................................... 27
5. Accidental Eccentric ................................................................................................................................. 28
Chapter Ⅺ. Structural System Evaluation and 0.2V0 ................................................................................... 28
1. Overturning Moment and Percentage(According to<Code for seismic design of building>) .. 28
2. Overturning Moment and Percentage ....................................................................................................... 29
Chapter Ⅻ. Deformation ......................................................................................................................................... 30
1. Floor Displacement Summary ..................................................................................................................... 30
Chapter ⅩⅢ. Wind Vibration Acceleration in Apex ..................................................................................... 35
Chapter ⅩⅣ. Anti-overturning and Stabilization ....................................................................................... 35
1. Anti-overturning ......................................................................................................................................... 35
2. Overall Stability ....................................................................................................................................... 36
3. Second-order Effect and Internal Force Modification ................................................................... 36
Chapter ⅩⅤ. Structural Analysis and Design Results Diagram ............................................................... 37
1. Floor Diagram ............................................................................................................................................... 37
2. Loads Diagram ............................................................................................................................................... 45
-2-
CABR-PKPM
1.<Code for design of concrete structures>GB50010-2010 (2015Version) Report date: 2022.5.26 18:23:12.
3.<Code for seismic design of buildings>GB 50011-2010 (2016Version) Chapter Ⅲ. General information of the project
4.<Load code for so of building structures>GB 50009-2012
Table 3-1 General information of the project
5.<Code for design of civil air defense basement>GB 50038-2005
6.<Technical specification for concrete structures of tall building>JGJ3-2010 Type Value Type Value
7.<Technical specification for concrete structures with specially shaped Location Function
columns>JGJ149-2017 Area(m^2) Designed Lifetime
8.<Technical specification for steel plate shear walls>JGJ/T 380-2015 Height(m) 27.200 Embedded end story No. 1
9.<Technical code for steel structure of light-weight building with gabled
Steel frame -
frames>GB51022-2015
Number of floors 7/0 Structure System supporting
10.<Unified standard for reliability design of building structures>GB 50068-2018
structure
11.<Technical specification for steel tube-reinforced concrete column structures>CECS
Basic wind
Ground Roughness B 0.98
28:2012
pressure(kN/m^2)
12. 《组合结构设计规范》(JGJ138-2016)
Seismic fortification
class B Seismic Group Group Three
13.<Technical specification for steel structure of tall building>JGJ99-2015
category
14. 《工程结构通用规范》(GB55001-2021)
Seismic fortification
8(0.2g) Site Classification Class Ⅱ
15. 《建筑与市政工程抗震通用规范》(GB55002-2021)
intensity
16. 《钢结构通用规范》(GB55006-2021)
Site characteristic
17. 《混凝土结构通用规范》(GB55008-2021) 0.45 αmax 0.1600
period(s)
-3-
CABR-PKPM
6 floor 1
X 1/684 < 1/250 YES
tower
earthquake
Chapter Ⅳ. Structure Evaluation Summary 7 floor 1
水平力作用下的
Y 1/828 < 1/250 YES
楼层层间最大 tower
Table 4-1 Summary Information
位移与层高之比 6 floor 1
X 1/1178 < 1/250 YES
Limitations (Δu/h)(强刚) tower
Index Value Distinguish Notes Wind Load
of Code 7 floor 1
Y 1/1033 < 1/250 YES
Total mass of structure(t) 1080.52 tower
-4-
CABR-PKPM
1) General Information: Wind load calculation information Calculation of horizontal wind load
-5-
CABR-PKPM
-6-
CABR-PKPM
-7-
CABR-PKPM
effect NO 1 1.00
Ways to consider occasional eccentric length For beam, floor live load reduction No reduction
Concord wind load combination YES considering the service life of the
structure 1.00
Floor live load reduction method Traditional way Fire truck load during beam design YES
-8-
CABR-PKPM
Consider component defects NO Steel tube bundle shear wall model model
according to SAUSAGE-Design NO Determinate weak Story by stiffness Strictly judge according to the anti code and
shear capacity NO
-9-
CABR-PKPM
- 10 -
CABR-PKPM
to biaxial bending and axial force Common way design of building structures> YES
The bending moment of frame beam is The main beam and secondary beam shall be in weight ratio 1.50
controlled by simply supported beam accordance with this clause Code for design and implementation of <Code for design of composite structures>JGJ
Processing method for main beam to steel reinforced concrete members 138-2016
control simply supported beam Piecewise calculation <Technical specification for concrete
columns columns>JGJ149-2017
The minimum value of vertical
Whether to execute<Design
reinforcement of structural edge
specification for pre-cost concrete
members is increased by 0.001Ac YES
shear wall structure>DB11/1003-2013 NO
Setting as a Construct edge
Concrete cover of beams (mm) 20.00
components,when the axial compression
Concrete cover of columns(mm) 20.00
ratio is less than the limit of <Code
Hoop spacing
for seismic design of buildings>GB
Beam Hoop spacing 100.00
50011 - 2010,6.4.5. YES
Column Hoop spacing 100.00
- 11 -
CABR-PKPM
Code for design and implementation of <Code for design of composite structures>JGJ 9) Load combination:
concrete-filled Square Steel Tubes 138-2016
The combination of seismic action and NO
- 12 -
CABR-PKPM
wind load m)
Normal wind and special wind are soil layer (m value) 3.00
Combined principles of roof live load, Roof live load, wind load and snow load are backfill ground in Y-direction 0.00
snow load and wind load combined at the same time Water and soil pressure parameters on
Horizontal seismic factor (non-master Backfill soil side pressure factor 0.50
Height difference between outdoor Outdoor ground additional load (kN/m2) 0.00
ground and bottom of structure (unit: 0.00 Out-of-plane design method Finite Element Method
- 13 -
CABR-PKPM
Concrete cover of interior wall defense, adjust the bending moment and
- 14 -
CABR-PKPM
forces method NO
14) Design Information:
Pass construction step load NO
- 15 -
CABR-PKPM
2. Floor Information yielding under medium and large earthquakes is selected, the program automatically uses
4 62 Q345 15 Q345
The design values of steel bar strength are shown in the table. When the design of non
3 92 Q345 18 Q345
yielding under medium and large earthquakes is selected, the program automatically uses
2 175 Q345 23 Q345
the standard value of material strength for calculation.
1 128 Q345 23 Q345
- 16 -
CABR-PKPM
Centroid Small
Story Story Transfer SSin Transfer Soft DR is
H Elevation Area Coordinates B L BMAX BMIN CEEL SS Part HS
No. No. Story Bottom Story story 1.0.
(X, Y) on Top
No. Concrete
表 5-6 各层的柱、墙面积信息(单位:m^2) Concrete Grade Steel Grade Steel Grade
Grade
Story No. 楼层面积 柱面积 墙面积 X 向墙面积 Y 向墙面积 1-7 C35 C35 Q345 Q345
- 17 -
CABR-PKPM
Load Case 8 EXP X-dir Positive Eccentric Earthquake 2. Load Case Information
Load Case 9 EXM X-dir Negative Eccentric Earthquake
Table 6-2 Permanent Load Information
Load Case 10 EYX Y + X earthquake (bidirectional effect)
- 18 -
CABR-PKPM
NO. Combination
2 1.00*DL 1.50*LL
Condition name Factor Factor of Factor of Factor of
3 1.30*DL 1.50*WL
seismic combination effective
4 1.30*DL -1.50*WL
combination value seismic weight
5 1.00*DL 1.50*WL
value
6 1.00*DL -1.50*WL
Live Load 1.50 -- 0.70 0.50
7 1.30*DL 1.50*LL 0.90*WL
Wind Load 1.50 0.20 0.60 0.00
8 1.30*DL 1.50*LL -0.90*WL
- 19 -
CABR-PKPM
1. Mass Distribution The total mass produced by dead load includes structural dead weight and additional
dead load
Table 7-1 Mass Information The total mass of the structure includes the load, the mass generated by live load
and the additional mass, and the mass generated by the load under the custom working
Mass of Mass of Mass in
condition
Story No. 质心 X,Y,Z(m) Dead Load Live Load Each Floor Mass ratio
(t) (t) (t) The total mass due to live load, the total mass due to custom load and the total mass
7 10.50,10.43,27.20 43.4 17.8 61.2 61.2 of the structure are the result of the reduction of live load (1t = 1000kg)
2 12.67,13.54, 8.50 108.4 31.8 140.2 140.2 Xstif、Ystif(m): X, Y coordinate value of rigid center
Represents that the floor mass ratio does not meet the Transfinite of 1.50 of high
Eex、Eey: Eccentricity in X and Y directions
regulation 3.5.6
Total mass produced by dead load (t): 904.403 Story No. Xstif Ystif Alf Eex Eey
Total mass of structure (t): 1080.521 5 11.55 11.12 0.00 12.26% 5.32%
- 20 -
CABR-PKPM
Story No. Xstif Ystif Alf Eex Eey Wind Load Shear Force Bending
4 11.49 10.50 0.00 6.51% 3.11% Story No. in Each in Each Moment in
Wind pressure unit: kN/m2 Table 8-2 Y-direction Wind Load Information
- 21 -
CABR-PKPM
The definition of irregular lateral stiffness in article 3.4.3-2 of code for seismic
Chapter Ⅸ. Vertical Irregularity design is as follows: the lateral stiffness of the floor is less than 70% of the adjacent
upper floor, or less than 80% of the average lateral stiffness of the three adjacent
1. Story Lateral Stiffness
floors above it; the lateral stiffness ratio of some floors of the structure does not
Ratx, Raty (ratio of stiffness): ratio of shear stiffness of the tower in this floor meet the requirements of the code, see the stiffness ratio 1 in the table below for
RJX,RJY: Structural shear stiffness in global coordinate system Ratx1, Raty1 (stiffness ratio 1):the smaller of the ratio of the lateral displacement
stiffness of the tower in the X and Y directions to the lateral rigidity of the
Table 9-1 Lateral Stiffness and Stiffness Ratio
corresponding tower of the upper layer of 70% or the average lateral rigidity of the
upper three layers of 80% (According to the anti-regulation 3.4.3; high-profile 3.5.2-1)
Story No. RJX(kN/m) RJY(kN/m) Ratx Raty
2 1.41e+6 1.26e+6 1.38 1.21 Story No. RJX(kN/m) RJY(kN/m) Ratx1 Raty1
- 22 -
CABR-PKPM
Story No. RJX(kN/m) RJY(kN/m) Ratx1 Raty1 Story No. Vx(kN) Vy(kN) Vx/Vxp Vy/Vyp OK or not
一楼层的 65%。 User-specified weak story:The weak story specified in parameters and multi tower
definitions
结构设定的限值是 65.00%。并无楼层承载力突变的情况
weak story:the floor whose stiffness ratio does not meet the specification requirements
Vx(kN)、Vy(kN): Floor shear capacity (x, Y direction) (Stiffness ratio judgment method: strict resistance and high
regulation judgment)
Vx/Vxp、Vy/Vyp: the ratio of the bearing capacity of this floor to the upper floor
(X, Y direction) (The principle of judging the weak story: stiffness ratio 1 and
weak story:Floor whose shear bearing capacity does not meet the requirements of the
Story No. Vx(kN) Vy(kN) Vx/Vxp Vy/Vyp OK or not
code
7 2271.47 4824.18 1.00 1.00 YES
6 2453.19 5210.11 1.08 1.08 YES C_def: Default adjustment factor of weak story (based on the above three
judgments)
5 2616.57 3823.66 1.07 0.73 YES
- 23 -
CABR-PKPM
C_final: The final adjustment factor of weak story Chapter Ⅹ. Seismic Action
Table 9-4 weak story Modification factor 1. Period and Model Shape
User The most unfavorable direction angle of earthquake action: -0.64 degree
0.843
3 155.73 X 13% 71% 16% 87% 4.00%
Note: At present, there is a case where the ratio of the shear bearing capacity is less
2
than the given Transfinite, and the program does not automatically adjust it. If it
0.617
4 98.13 T 83% 0% 17% 17% 4.00%
is confirmed as a weak story, please fill in the weak story number in "Parameter
8
Definition-> Adjustment Information" If you need automatic adjustment, you can check
0.539
"Automatic adjustment of weak story due to sudden change in shear bearing capacity" 5 12.01 T 87% 12% 1% 13% 4.00%
3
- 24 -
CABR-PKPM
Vibratio Angle vibratio on on vibratio Dampin Vibratio Angle vibratio on on vibratio Dampin
Perio Typ Perio Typ
n model (degree n vibration vibration n g n model (degree n vibration vibration n g
d (s) e d (s) e
No. ) proporti proportio proportio proporti ratio No. ) proporti proportio proportio proporti ratio
on n n on on n n on
1 0.335
15 87.40 T 83% 1% 17% 17% 4.00%
0.486 6
7 89.28 T 88% 0% 12% 12% 4.00%
9 0.323
16 86.22 T 71% 0% 29% 29% 4.00%
0.481 8
8 88.76 T 91% 0% 9% 9% 4.00%
3 0.310
17 175.64 X 48% 51% 1% 52% 4.00%
0.461 4
9 89.29 T 91% 0% 8% 9% 4.00%
1 0.290
18 14.55 T 98% 2% 0% 2% 4.00%
0.455 0
10 179.36 T 60% 40% 0% 40% 4.00%
7 0.280
19 84.84 T 73% 3% 25% 27% 4.00%
0.445 6
11 85.18 T 76% 0% 24% 24% 4.00%
0 0.272
20 80.72 T 77% 2% 21% 23% 4.00%
0.405 8
12 174.64 X 14% 85% 1% 86% 4.00%
4 0.268
21 161.85 T 82% 16% 3% 18% 4.00%
0.362 0
13 44.93 T 88% 6% 6% 12% 4.00%
4
0.338
14 64.73 T 91% 3% 6% 9% 4.00%
3
表 10-2 结构周期比
- 25 -
CABR-PKPM
第一扭转周期 Vibration model 第一平动周期 Vibration model Torsion X-direction Y-direction Lateral
周期比 Vibration Period Angle
(s) No. (s) No. Type vibration vibration vibration vibration
model No. (s) (degree)
1.4680 1 0.8666 2 1.69 proportion proportion proportion proportion
说明:此处计算周期比采用的扭转和平动振型通过平动和扭转因子进行判断,程序无法确定其是 有蓝色底色标识位置双击可以查看图形
否为整体振型,
2. Period and Model Shape 第一扭转周期 Vibration model 第一平动周期 Vibration model
周期比
(s) No. (s) No.
Table10-3 Period and direction [Forced rigid floor assumption]
0.2987 3 0.6363 1 0.47
5 0.2094 91.54 Y 7% 0% 92% 93% Table 10-5 Earthquake direction and Effective mass factor of vibration modal
6 0.1767 3.19 T 70% 28% 2% 30%
- 26 -
CABR-PKPM
11 0.01% 0.07% 12 4.12% 0.24% Coef_RSWx,Coef_RSWy: The program comprehensively considers the final adjustment
13 0.13% 0.89% 14 0.08% 0.36% factor of shear weight ratio (if user-defined, user-defined value will be adopted)
It can be seen from the following table that the seismic shear weight ratio in X direction
根据《抗规》5.2.2 条说明,振型个数一般可以取振型参与质量达到总质量 90%所需的振型数。
meets the requirements.
The effective mass factor of EX in 1 direction is 93.00%, and the participating modes
Table 10-6 Index in EX
are sufficient
- 27 -
CABR-PKPM
- 28 -
CABR-PKPM
- 29 -
CABR-PKPM
Total
Wall and
Story No. Frame column shear The unit of displacement in the table is (mm)
bracing
force
《抗规》3.4.3-1 条对于扭转不规则的定义为:在规定的水平力作用下,楼层的最大弹性水平
Maximum floor displacement of the whole building under this condition= 20.77(occur
位移(或层间位移),大于该楼层两端弹性水平位移(或层间位移)平均值的 1.2 倍。结构设定的
on floor 7 tower 1)
判断扭转不规则的位移比为 1.20,位移比的限值为 1.50,结构不属于扭转不规则。
Maximum displacement ratio of the whole building under this condition = 1.48 (occur
Under all working conditions, the displacement ratio and inter story displacement ratio
on floor 1 tower 1)
meet the requirements of the code.
Maximum story to floor displacement ratio of the whole building under this condition=
- 30 -
CABR-PKPM
1.48(occur on floor 1 tower 1) Maximum story to floor displacement ratio of the whole building under this condition=
有蓝色底色标识位置双击可以查看图形
(specified horizontal force) Table 12-3 Displacement of Y-direction positive eccentric static earthquake
6 16.34(381) 16.09 3.49 3.40 1.02 1.02 7 19.46(462) 19.09 3.60 3.18 1.02 1.13
5 12.85(326) 12.73 4.19 3.91 1.01 1.07 6 15.90(381) 15.88 2.68 2.57 1.00 1.05
4 9.04(282) 8.73 3.04 2.54 1.04 1.20 5 13.42(326) 13.30 4.93 4.76 1.01 1.04
3 6.57(218) 5.37 1.83 1.47 1.22 1.24 4 8.64(316) 8.57 3.73 3.70 1.01 1.01
2 4.98(117) 3.66 1.66 1.26 1.36 1.31 3 5.10(274) 4.93 1.82 1.77 1.03 1.02
1 3.32(30) 2.37 3.32 2.37 1.40 1.40 2 3.38(210) 3.11 1.84 1.77 1.09 1.04
on floor 7 tower 1) Maximum floor displacement of the whole building under this condition= 19.46(occur
on floor 7 tower 1)
Maximum displacement ratio of the whole building under this condition = 1.40 (occur
on floor 1 tower 1) Maximum displacement ratio of the whole building under this condition = 1.16 (occur
on floor 1 tower 1)
- 31 -
CABR-PKPM
Maximum story to floor displacement ratio of the whole building under this condition= Maximum story to floor displacement ratio of the whole building under this condition=
有蓝色底色标识位置双击可以查看图形 有蓝色底色标识位置双击可以查看图形
Table 12-4 Displacement of Y-direction negative eccentric static earthquake Table 12-5 Displacement of X-direction earthquake condition
7 20.41(423) 19.18 3.20 3.13 1.06 1.02 7 19.93(423) 3.57 3.32 1/755(423)
6 17.28(381) 16.02 2.75 2.56 1.08 1.07 6 16.62(381) 3.65 3.41 1/684(381)
5 14.54(326) 13.45 5.32 4.83 1.08 1.10 5 13.25(326) 3.99 3.86 1/1503(332)
4 9.22(282) 8.65 4.03 3.75 1.07 1.08 4 9.38(282) 2.86 2.49 1/1574(289)
3 5.19(218) 4.80 1.98 1.74 1.08 1.14 3 6.89(218) 1.65 1.42 1/1813(218)
2 3.28(101) 3.10 1.93 1.79 1.06 1.08 2 5.26(117) 1.75 1.26 1/2280(117)
1 1.35(14) 1.31 1.35 1.31 1.03 1.03 1 3.53(30) 3.53 2.45 1/1275(30)
Maximum floor displacement of the whole building under this condition= 20.41(occur Maximum floor displacement of the whole building under this condition= 19.93(occur
Maximum displacement ratio of the whole building under this condition = 1.08 (occur Maximum story drift angle of the whole building under this condition = 1 / 684 (occur
- 32 -
CABR-PKPM
有蓝色底色标识位置双击可以查看图形
1 1.44(93) 1.44 1.34 1/3117(93) Maximum floor displacement of the whole building under this condition= 10.62(occur
on floor 7 tower 1)
Maximum floor displacement of the whole building under this condition= 18.75(occur
on floor 7 tower 1) Maximum story drift angle of the whole building under this condition = 1 / 1178 (occur
on floor 6 tower 1)
Maximum story drift angle of the whole building under this condition = 1 / 828 (occur
有蓝色底色标识位置双击可以查看图形
- 33 -
CABR-PKPM
Maximum floor displacement of the whole building under this condition= 12.43(occur Maximum floor displacement of the whole building under this condition= 20.17(occur
Maximum story drift angle of the whole building under this condition = 1 / 1033 (occur Maximum story drift angle of the whole building under this condition = 1 / 677 (occur
有蓝色底色标识位置双击可以查看图形 有蓝色底色标识位置双击可以查看图形
- 34 -
CABR-PKPM
区(零应力区);其他建筑,基础底面与地基土之间脱离区(零应力区)面积不应超过基础底面面
Maximum floor displacement of the whole building under this condition= 19.12(occur
积的 15%。
on floor 7 tower 1)
The checking Calculation result for the Overturn Resistance of the Whole Structure is
Maximum story drift angle of the whole building under this condition = 1 / 805 (occur
as follows:
on floor 7 tower 1)
- 35 -
CABR-PKPM
Load Anti overturning Overturning moment Ratio Mr/Mov Zero stress shall comply with the following provisions: the first-order linear elastic analysis
case moment Mr (kN. m) Mov (kN. m) zone (%) or the second-order linear elastic analysis can be used for the structural internal
WX 1.04e+5 13889.93 7.52 0.00 force analysis. When the second-order effect factor is less than 0.1, the first-order
WY 58708.37 15665.41 3.75 0.00 elastic analysis can be used; when the second-order effect factor is greater than 0.1
and less than 0.25, the second-order linear elastic analysis or direct analysis should
be adopted; when the second-order effect factor is greater than 0.25, the lateral
This part of v3.1.1 and later uses more accurate calculation formula of the ratio of The maximum second-order effect factor of the structure (0.01, 1 floor of 1 tower) is
rigidity to weight, which is different from the previous version. Please refer to the not greater than 0.1. The first-order elastic analysis or second-order elastic analysis
user manual for details. can be used for the structural internal force analysis. The maximum second-order effect
factor (0.01, 1-storey, 1-Tower) is not greater than 0.25, which can pass the stability
Table 14-2 Checking rigid weight ratio based on seismic action
calculation of steel structure standard GB 50017-2017 5.1.6.
EY EJD/GH^2 11.35
According to article 5.1.6 of GB 50017-2017, the stability calculation of frame column Table14-3 Second-order Effect
- 36 -
CABR-PKPM
1. Floor Diagram
- 37 -
( 128)
( 126)
( 127)
HW250X250[ 39]
( 10) ( 11)
HW300X300[ 39]
HW300X300[ 39]
HW250X250[ 39]
( 121) ( 122) ( 123) ( 124) ( 125)
( 5)
上
( 12)
( 13)
( 2)
HM440X300[ 39] 上
HM440X300[ 39]
HM440X300[ 39] HM440X300[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 117)
( 118)
( 119)
( 120)
( 115)
( 116)
( 113) ( 114)
HN200X100[ 39] HN200X100[ 39]
( 109)
( 110)
( 111)
( 112)
( 108)
( 105) ( 106) ( 107)
HN300X150[ 39]
HM440X300[ 39] HM440X300[ 39] HM440X300[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 101)
( 102)
( 103)
( 104)
( 100)
( 99)
( 96) ( 97) ( 98)
HM440X300[ 39] HM440X300[ 39] HM440X300[ 39]
( 92)
( 93)
( 94)
( 95)
( 91)
( 89) ( 90)
HN300X150[ 39]
HN200X100[ 39] HN200X100[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 85)
( 86)
( 87)
( 88)
( 83)
( 84)
HM488X300[ 39]
HN200X100[ 39]
HN200X100[ 39]
HM488X300[ 39]
( 80) ( 81) ( 82)
HM440X300[ 39] HM440X300[ 39] HM440X300[ 39]
( 76)
( 77)
( 78)
( 79)
HW300X300[ 39]
( 5) ( 6) ( 7) 消能梁 ( 8)
HW300X300[ 39]
HW300X300[ 39]
( 62) ( 63) ( 64) ( 65) ( 66) ( 67) ( 68) ( 69) ( 70)
( 71) ( 72) ( 73) ( 74) ( 75)
( 7)
上
HN300X150[ 39]
HN300X150[ 39]
39]
HN250X125[ 39]
39]
39]HM390X300[ 39]
( 9)
( 1)
HM340X250[ 39] HM340X250[ 39]HM340X250[ 39] HM340X250[ 39]
H450X300X16X16[
H450X300X16X16[
1] H450X300X16X16[
1] H450X300X16X16[
1]
H450X300X16X16[ 1]上1]
H450X300X16X16[
H450X300X16X16[
1] 1]
H450X300X16X16[
H450X300X16X16[
1] 1] HM340X250[ 39]
HN250X125[
HN200X100[
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
HN400X200[ 39]
( 54)
( 55)
( 56)
( 57)
( 58)
( 59)
( 60)
( 61)
( 53)
( 46) ( 47) ( 48) ( 49) ( 50) ( 51) ( 52)
39]HM390X300[
HN250X125[ 39] HN400X200[
HN400X200[
39] 39] HN400X200[ 39]HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
39]
( 45)
( 43)
( 44)
( 10) ( 9)
39]HM390X300[
( 42)
39]
( 41)
( 39) ( 40)
HW300X300[ 39] HW300X300[ 39]
HN300X150[ 39]
39]HM390X300[
39]HM390X300[
HN250X125[ 39] HN400X200[ 39]
HN400X200[ 39]
39]
( 36)
( 38)
( 37)
HM390X300[
HM390X300[
( 35)
39]
( 30)
( 29) ( 34)
上
上 上
HN200X100[
HM390X300[ 39]HM390X300[ 39]HM390X300[
HM390X300[ 39]HM390X300[ 39]HM390X300[
( 28)
( 26)
( 27)
HN400X200[ 39]
( 21)
( 19)
( 20)
HN200X100[ 39]
( 18)
HM488X300[
( 12)
( 13)
( 9)
HW300X300[ 39]
( 1) ( 2) 消能梁 ( 3)
HW300X300[ 39]
HW300X300[ 39]
( 1) ( 2) ( 3) ( 4) 上 ( 5) ( 6) ( 7) ( 8)
( 8)
( 4)
( 4)
HM340X250[ 39] H450X300X16X16[
H450X300X16X16[
1] H450X300X16X16[
1] H450X300X16X16[ 1] 上
1] H450X300X16X16[ 1] H450X300X16X16[ 1] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
HM244X175[ 39]
HN200X100[ 39]
HN250X125[ 39] HN250X125[ 39]
( 171)
( 172)
( 173)
HW250X250[ 39]
( 10) ( 11)
HW300X300[ 39]
HW300X300[ 39]
HW250X250[ 39]
( 10)
( 165) ( 166) ( 167) ( 168) 上 ( 169) ( 170)
( 12)
( 13)
( 4)
上 HM340X250[ 39] HM340X250[ 39]HM340X250[ 39] HM340X250[ 39] HM244X175[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 163)
( 164)
HN250X125[ 39]
HM340X250[ 39]
( 161)
( 162)
( 159)
( 160)
( 158)
HN200X100[ 39]
( 156)
( 157)
( 155)
( 152) ( 153) ( 154)
HN300X150[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 148)
( 149)
( 150)
( 151)
( 145)
( 146)
( 147)
( 142) ( 143) ( 144)
HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
( 138)
( 139)
( 140)
( 141)
( 137)
( 135) ( 136)
HN300X150[ 39]
HN200X100[ 39] HN200X100[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 131)
( 132)
( 133)
( 134)
( 129)
( 130)
HM340X250[ 39]
HN200X100[ 39]
HN200X100[ 39]
HM340X250[ 39]
( 126) ( 127) ( 128)
HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
( 122)
( 123)
( 124)
( 125)
HW300X300[ 39]
( 5) ( 6) ( 7) ( 8)
HW300X300[ 39]
HM390X300[ 39]
HM488X300[ 39]
HM390X300[ 39]
HW300X300[ 39]
( 106) ( 107) ( 108) ( 109) ( 110) ( 111)( 112)
( 113)( 114) ( 115) ( 116)上 ( 117) ( 118) ( 119) ( 120) ( 121)
( 1)
( 9)
( 5)
340X250[上
[ 14a[ 32]
( 99) 32]
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
HM340X250[ 39] HM340X250[ 39]HM340X250[HM
39]
340X250[ H
39]
M340X250[
HM39]
340X250[
HM340X250[
HM39]
340X250[
HM
39]
340X250[
39]
HM340X250[
39] HM39] H39]
M340X250[ 39]
HM340X250[ 39]
HM340X250[
HM39]
340X250[ 39] HM340X250[ 39]
( 100)
( 101)
( 102)
( 103)
( 104)
( 105)
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 95)
( 96)
( 97)
( 98)
HN400X200[ 39]
[ 14a[
39]HM390X300[ 39]
M488X300[ 39]
39]
( 85) ( 86) ( 87) ( 88)( 89) ( 90) ( 91) ( 92) ( 93) ( 94)
( 84)
HM390X300[
HN250X125[ 39] HN250X125[
HN39]
400X200[
HN400X200[
HN39]
400X200[
HN39]
400X200[
39] 39]
HN400X200[ 39] HN400X200[ 39] HN400X200[
HN39]
400X200[ 39]
( 81)
( 82)
( 83)
M390X300[ 39]
39]
N200X100[ 39]
N200X100[ 39]
( 7) ( 9)
39]
H
( 77) ( 78) ( 79) ( 80)
( 71) ( 76)
HM488X300[
( 75)
HM390X300[
39] HM390X300[
39]
( 72)
( 73)
( 74)
HN300X150[ 39]
39]
H
( 70)
39]
HN250X125[ 39]
HN250X125[ 39]
HN200X100[H39]
HN200X100[H39]
HM488X300[
( 65) ( 66) ( 67) ( 68) ( 69)
HN400X200[ 39]
HM390X300[
39]
39]
HM390X300[
( 64)
( 52) ( 63)
HN400X200[ 39] HN400X200[ 39]
HN400X200[
HN400X200[
39] 39]HN400X200[ 39]
( 60) ( 61) ( 62)
HN200X100[ 39]
( 53) 39]
HM488X300[
HM390X300[
( 55)
( 56)
( 57)
( 58)
( 59)
( 54)
上 上
39]
N200X100[
HN250X125[ 39]HN250X125[
HN250X125[
39] 39]
HM390X300[ 39] HM390X300[ 39]HM390X300[
39]
上 上
HN250X125[ 39]
HN250X125[ 39]
HN200X100[ 39]
HN200X100[ 39]
( 48) ( 49) ( 50) ( 51)
39]HM488X300[
( 46)
( 47)
( 45)
HM390X300[
39]
39]
( 34) (H44)
( 33) ( 43)
HM488X300[
( 39)
( 40)
( 41)
( 42)
( 36) ( 37) ( 38)
HM390X300[
( 35)
( 3) HN250X125[ 39]HN250X125[
HN250X125[
39] 39] ( 6)
39]
( 28) ( 29) ( 30) ( 31) ( 32) HN300X150[ 39]
HM488X300[
HM390X300[
( 27)
HN400X200[ 39]
( 25)
( 26)
( 24)
HM488X300[ 39]
HM390X300[ 39]
( 18) ( 19) ( 20) ( 21) ( 22) ( 23)
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
[ 14a[ 32]
HN250X125[ 39] HN400X200[ 39]
HN400X200[ 39] HN400X200[ 39] HN400X200[
HN400X200[
39] 39]
( 11)
( 12)
( 13)
( 14)
( 15)
( 16)
( 17)
HW300X300[ 39]
( 1) ( 2) ( 3)
HW300X300[ 39]
HW300X300[ 39]
( 1) ( 2) ( 3) ( 4) ( 5) 上 ( 6) ( 7) ( 8) ( 9) ( 10)
( 2)
( 4)
( 8)
HM340X250[ 39] HM340X250[ 39]
HM340X250[
HM340X250[ 39] 上
39]HM340X250[
H39]
M340X250[ 39] HM340X250[ 39]
HM340X250[
HM340X250[
39] 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
- 39 -
HW300X300[ 39]
HW300X300[ 39]
( 92)
( 10)
( 9)
HM340X250[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 90)
( 91)
( 89)
HN350X175[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 87)
( 88)
( 86)
HN350X175[ 39]
HN400X200[ 39]
HN400X200[ 39]
( 85)
( 83)
( 84)
HN200X100[ 39]
( 81)
( 82)
HW250X250[ 39]
( 5) ( 6) ( 7)
HW300X300[ 39]
HW250X250[ 39]
( 75) ( 76) ( 77) ( 78) ( 79) ( 80)
( 1)
上
HM390X300[ 39]
( 8)
( 4)
HM340X250[ 39] 上 HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
[ 14a[ 32]
[ 14a[ 32]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
HN400X200[ 39]
( 70)
( 71)
( 72)
( 73)
( 74)
HM390X300[ 39]
HM488X300[ 39]
39]
( 69)
( 65) ( 66) ( 67) ( 68)
39] HM390X300[
HN250X125[ 39] HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
39]
( 62)
( 63)
( 64)
HM390X300[
( 5) ( 58) ( 59) ( 60) ( 61) ( 2)
39]
39]
( 57)
HN250X125[ 39]
HN250X125[ 39]
( 56)
HW250X250[ 39]HN250X125[ 39] HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
39] HM390X300[
39] HM488X300[
HW250X250[ 39]
39]HM390X300[
HN350X175[ 39]
( 54)
( 55)
( 52)
( 53)
39]
39]
( 51)
HN400X200[ 39]
HM390X300[
39] HM488X300[
39]
( 46)
( 40) ( 47)
( 43) ( 44)
( 45)
上 上
HN250X125[ 39]
HN250X125[ 39]
( 31) HN200X100[
HN250X125[ 39]HN250X125[
HN250X125[
39] 39]
HM390X300[ 39] HM390X300[ 39]HM390X300[
39] HM488X300[
上 上
39] HM390X300[
HN200X100[ 39] HN200X100[ 39]
( 41)
( 42)
( 39)
( 38)
( 36)
( 37)
39]
39]HM488X300[
HM390X300[
( 32)
( 8) HN250X125[ 39]HN250X125[ ( 7)
( 30)
HN250X125[
39] 39] ( 27) ( 28) ( 29)
HN350X175[ 39]
39]HM488X300[
HM390X300[
( 26)
HN400X200[ 39]
( 25)
( 24)
HM488X300[
( 20)
9) 32]( 19)
HM390X300[ 39]
( 16) ( 17) ( 18)
HN250X125[ 39]HN250X125[
HN39]
250X125[ 39]
[ 14a[ 32]
HM488X300[
[ 14a[ 32]
[ 14a[ 32]
HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
( 13)
( 14)
( 15)
[ (14a[
( 10)
( 11)
( 12)
HW250X250[ 39]
( 1) ( 2) ( 3)
HW300X300[ 39]
HW250X250[ 39]
( 1) ( 2) ( 3) ( 4) ( 5) ( 6) ( 7) ( 8)
( 6)
( 4)
( 3)
HM340X250[ 39]HM340X250[
HM 39]
340X250[H39]
M340X250[ 39] HM340X250[ 39] 上 HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
- 40 -
( 62)
( 60)
( 61)
HW250X250[ 39]
( 4) ( 5) ( 6)
HM390X300[ 39]
HW250X250[ 39]
( 56) ( 57) ( 58) ( 59)
( 3)
上
上 上
( 6)
上
[ 14a[ 32]
HM340X250[ 39] HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 52)
( 53)
( 54)
( 55)
39]HM390X300[ 39]
M488X300[ 39]
M390X300[ 39]
( 49) ( 50) ( 51)
( 2) ( 5)
HN250X125[ 39] HN400X200[ 39] HN400X200[ 39]
( 46)
( 47)
( 48)
HW250X250[ 39] HW250X250[ 39]
39]
39]
H
H
( 44) ( 45)
HM488X300[
39]HM390X300[
39] HM390X300[
( 42)
( 43)
39]
39]
( 41)
39]
HN250X125[ 39]
HN250X125[ 39]
HM488X300[
( 38) ( 39) ( 40)
39] HM390X300[
39]
HM390X300[
( 37)
( 28) ( 36)
HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
( 33) ( 34) ( 35)
HN200X100[ 39]
( 29) 39]
HM488X300[
HM390X300[
( 30)
( 31)
( 32)
39]
N200X100[
HN250X125[ 39]HN250X125[
HN250X125[
39] 39]
HM390X300[ 39] HM390X300[ 39]HM390X300[
HN250X125[ 39]
HN250X125[ 39]
( 26) ( 27)
39]HM488X300[
( 24)
( 25)
( 23)
39]
HM390X300[
( 15) (H22) HN200X100[ 39] HN200X100[ 39]
HM488X300[
( 19)
( 20)
( 21)
( 16) ( 17) ( 18)
HN250X125[ 39]HN250X125[
HN250X125[
39] 39]
HM390X300[ 39]
( 12) ( 13) ( 14)
HM488X300[
( 11)
( 10)
( 9)
( 8) ( 9)
HM488X300[ 39]
HM390X300[ 39]
( 7) ( 8)
HW250X250[ 39] HW250X250[ 39]
HN250X125[ 39] HN400X200[ 39]
( 4)
( 5)
( 6)
HW250X250[ 39]
HW250X250[ 39]
( 1) ( 2) ( 3)
HW250X250[ 39]
( 1) ( 2) ( 3)
( 7)
( 4)
上 上 上 上
( 1)
HM340X250[ 39] HM340X250[ 39] 上 HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
- 41 -
( 76)
244X175[ 39]
HN200X100[ 39]
( 74)
( 75)
HM1]
1]
HW250X250[ 39]
( 4) ( 5) ( 6)
1300X400X20X36[
H1300X400X20X36[
HW250X250[ 39]
( 72) ( 73)
( 6)
上
上 上
( 1)
HM340X250[ 39] 上 HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 69)
( 70)
( 71)
1]
1]
H1300X400X20X36[
H1300X400X20X36[
HM390X300[ 39] HM390X300[ 39] HM390X300[ 39]HM390X300[ 39]HM390X300[ 39]
( 67) ( 68)
1] H1300X400X20X36[H1]
HN250X125[ 39] HN400X200[ 39]
1]
1]
( 65)
( 66)
( 64)
1] H1300X400X20X36[
1] H1300X400X20X36[
1]
1]
( 60) ( 61) ( 62) ( 63)
H1300X400X20X36[
( 59)
H1300X400X20X36[
( 58) H1300X500X20X36[ 1] H1300X500X20X36[ 1] H1300X500X20X36[ 1] H1300X500X20X36[ 1]
1]
1]
( 56)
( 57)
1]H1300X400X20X36[
1]H1300X400X20X36[
HN250X125[ 39]
( 5) ( 3)
( 55)
1]
1]
( 53)
( 54)
HN250X125[ 39]
HN250X125[ 39]
( 49) ( 50) ( 51) ( 52)
1] H1300X400X20X36[
1] H1300X400X20X36[
1]
HW250X250[ 39] HW250X250[ 39]
( 47)
( 48)
HN300X150[ 39]
HN300X150[ 39]
HN300X150[ 39]
HN300X150[ 39]
H1300X400X20X36[
H1300X400X20X36[
( 40) ( 41) ( 42) ( 43) ( 46)
HM294X200[ 39]
39]
( 44)
( 45)
H1300X400X20X36[
H1300X400X20X36[
HM294X200[
( 38)
( 39)
HM294X200[ 39]HM294X200[
HM294X200[
39] H39]
N200X100[ 39] HN200X100[ 39]
HN250X125[ 39]
HN250X125[ 39]
( 33)
( 34)
( 35)
( 36)
( 37)
H1300X400X20X36[
H1300X400X20X36[
( 2) ( 8)
( 31)
( 32)
1]
1]
( 28)
( 29)
( 24) ( 25) ( 26) ( 27) H1300X400X20X36[ ( 30)
H1300X400X20X36[
HW250X250[ 39] HW250X250[ 39]
( 22)
( 23)
H1300X400X20X36[
H1300X400X20X36[
HM294X200[ 39]HM294X200[
HM294X200[
39] H39]
N200X100[ 39] HN200X100[ 39]
( 18) ( 19) ( 20) ( 21)
1]
( 15)
( 16)
H1300X400X20X36[
( 17)
HN300X150[ 39]
HN300X150[ 39]
HN300X150[ 39]
HN300X150[ 39]
( 13)
( 14)
1]
1]
H1300X400X20X36[
H1300X400X20X36[
( 11)
( 12)
( 7) ( 8) ( 9) ( 10)
HN250X125[ 39] H1300X500X20X36[ 1] H1300X500X20X36[ 1] H1300X500X20X36[ 1] H1300X500X20X36[ 1]
( 4)
( 5)
( 6)
HW250X250[ 39]
( 1) ( 2) ( 3)
HW250X250[ 39]
( 1) ( 2) ( 3)
( 4)
上 上上
( 7)
HM340X250[ 39] 上 HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
- 42 -
( 61)
( 59)
( 60)
( 4) ( 5) ( 6)
M390X300[ 39]
( 57) ( 58)
HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
( 54)
( 55)
( 56)
39] H39]
HM390X300[
( 50) 32]
HN250X125[ 39] HN400X200[ 39] HN400X200[ 39]
( 48)
( 49)
[ 14a[
( 47)
390X300[
( 43) ( 44) ( 45) ( 46)
( 42)
HM
390X300[ 39] HM390X300[ 39]HM390X300[ 39]
HN250X125[ 39]
( 38)
( 39)
( 40)
( 36)
( 37)
( 30) ( 31) ( 32) ( 33) ( 34) ( 35)
HN200X100[ 39]
HN200X100[ 39]
HN250X125[ 39]HN250X125[
HN250X125[
39] HN 39]
200X100[ 39] HN200X100[
HN200X100[
39] 39]
( 29) 32]
( 22)
( 23)
( 24)
( 25)
( 26)
( 27)
( 28)
[ 14a[
( 16) ( 17) ( 18) ( 19) ( 20) ( 21)
HN250X125[ 39]HN250X125[
HN250X125[
39] HN 39]
200X100[ 39] HN200X100[
HN200X100[
39] 39]
( 14)
( 15)
( 11)
( 12)
( 13)
39] HM
HM390X300[ 39]
( 10)
( 9)
( 6) ( 7) ( 8)
HN250X125[ 39]
HM390X300[
( 3)
( 4)
( 1) ( 2) ( 3)
( 1) ( 2)
HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[ 39]
- 43 -
440X300[ 39]
39]
( 4) ( 5) ( 6)
M390X300[ 39]
( 66) ( 67) ( 68)
HM488X300[
39]
[ 14a[ 32]
39]
39]
HM340X250[ 39] HM340X250[ 39] HM340X250[ 39]
( 64)
( 65)
HW400X400[ 39] HW400X400[ 39] HW400X400[
( 62)
( 63)
M488X300[
39]
( 58) ( 59) ( 60) ( 61)
HM440X300[
HM440X300[
HM440X300[HM
39]
M390X300[H39]
39]
39]
( 57)
( 55)
( 56)
HM488X300[
HM488X300[
39] HM488X300[
39]
HM488X300[
39] 39]
( 53) ( 54)
M488X300[
HM440X300[
HM440X300[
H39]
( 52)
HN400X200[ 39] HN400X200[ 39]
( 47)( 50)
( 51)
39] HM488X300[
( 48)
( 49)
HM440X300[ 39]
H39]
( 43) ( 44) ( 45) ( 46) ( 40) ( 41) ( 42)
39]
HN400X200[ 39]
HM390X300[ 39]HM390X300[H
39] HM488X300[
HM488X300[
HM488X300[
39] HM488X300[
39]
HM488X300[
39] 39]
HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
( 38)
( 39)
( 36)
( 37)
( 35)
HM488X300[
HM440X300[ 39]
( 34)
( 33)
N400X200[ 39]
( 32)
HN250X125[ 39]
( 31) HN200X100[ 39]
M488X300[
( 30)
HN200X100[ 39]
( 26)
( 27)
( 28)
( 29)
( 24) ( 25)
HM440X300[ 39]
HM488X300[H39]
HN400X200[H39]
HN400X200[ 39]
HM390X300[ 39]
HN250X125[ 39] HN200X100[ 39] ( 23)
( 20)
( 21)
( 22)
HN200X100[ 39]
( 18)
( 19)
HM440X300[ 39]
HM488X300[ 39]
HN400X200[ 39]
HN400X200[ 39]
HM390X300[ 39]
( 15) ( 16) ( 17)
HN250X125[ 39] HN200X100[ 39] HN200X100[ 39]
( 10)
( 11)
( 12)
( 13)
( 14)
HM440X300[ 39]
HM488X300[ 39]
HM390X300[ 39]
( 6) ( 7) ( 8) ( 9)
HN250X125[ 39] HN400X200[ 39] HN400X200[ 39] HN400X200[ 39]
( 3)
( 4)
( 5)
( 1) ( 2) ( 3)
( 1) ( 2)
HM340X250[ 39] HM340X250[ 39]
HW400X400[ 39] HW400X400[ 39] HW400X400[
- 44 -
2. Loads Diagram
DL: 1. 00
LL: 3. 50
DL: 4*99. 00*1. 30上 DL: 1*6. 00
LL: 4*35. 00*1. 30 DL: 4*4. 50*4. 00
上
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 DL: 1*6. 00
DL: 4*99. 00*1. 30 DL: 4*4. 50*4. 00
DL: 4*5. 00*1. 20 LL: 4*35. 00*1. 30 DL: 4*5. 00*1. 20
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 DL: 1*6. 00
DL: 4*4. 50*4. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 DL: 1*6. 00
DL: 4*4. 50*4. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
上 上
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1*6. 00
DL: 4*4. 50*4. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
第1层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
- 45 -
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
上 DL: 4*21. 00*3. 50
DL: 1*1. 00 DL: 1*1. 00 DL: 1*8. 00
DL: 1*1. 00
DL: 1. 00
LL: 3. 50
DL: 1. 00
LL: 3. 50
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00
LL: 3. 50 DL: 4*21. 00*3. 50
DL: 1*8. 00
DL: 1*1. 00
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 DL: 4*21. 00*3. 50
DL: 1*8. 00
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1*1. 00
上
DL: 1. 00 DL: 1. 00 DL: 1. D
00
L: 1.DL:
001. D
00
L: 1. 00 DL: 1. 00 DL: 1. 00 DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 LL: 3. LL:
50 3.LL:
503. LL:
50 3. 50 LL: 3. 50 LL: 3. 50 LL: 3. 50 LL: 3. 50
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 4*21. 00*3. 50
DL: 1*8. 00
DL: 1. 00 DL: 1. 00 DL: 1. 00
DL: 1. 00 LL: 3. 50 LL: 3. 50 LL: 3. 50
LL: 3. 50 DL: 1*1. 00
DL: 1*1. 00
DL: 1*1. 00
上 上
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1*1. 00 DL: 1. 00 DL: 1. 00
DL: 1. 00 DL: 1. 00 DL: 4*21. 00*3. 50
DL: 4*10. 00*0. 25
第2层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
- 46 -
DL: 4*16. 00*0. 56
DL: 4*24. 00*2. 88
DL: 1*6. 00
DL: 1*6. 00
DL: 1. 00
LL: 3. 50
上 DL: 4*16. 00*0. 56
上
DL: 1. 00 DL: 1. 00 DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 LL: 3. 50 LL: 3. 50
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1*1. 00
DL: 1*6. 00
DL: 1. 00
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 LL: 3. 50
上
DL: 1*1. 00 DL: 1*1. 00 上
DL: 1*1. 00
上 上
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
DL: 1*1. 00 LL: 3. 50 LL: 3. 50
DL: 1*6. 00
DL: 1*1. 00
DL: 1. 00
LL: 3. 50
DL: 1. 00
LL: 3. 50
DL: 4*10. 00*0. 58
第3层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
- 47 -
DL: 1. 00
LL: 3. 50
上
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 4* 15. 00* 2. 50
DL: 1. 00
DL: 1. 00 LL: 3. 50
LL: 3. 50 DL: 1* 1. 00
DL: 1* 1. 00 DL: 1* 1. 00
DL: 1* 1. 00 DL: 1*1. 00
DL: 1* 1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1* 1. 00 DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
DL: 1* 1. 00
DL: 1. 00
LL: 3. 50 DL: 1. 00
DL: 4*15. 00*0. 00
DL: 4*25. 00*0. 97
LL: 3. 50
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
上
上 上
上 上
第4层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
Figure 15-11 Fourth floor loads diagram
- 48 -
DL: 1. 00
LL: 3. 50
上
DL: 1. 00
DL: 1. 00 LL: 3. 50
LL: 3. 50 DL: 4* 900. 00*0. 00
DL: 1. 00
LL: 3. 50
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
上
上 上
第5层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
Figure 15-12 Fifth floor loads diagram
- 49 -
DL: 1. 00
LL: 3. 50
DL: 1. 00 DL: 1. 00
DL: 1. 00 LL: 3. 50 LL: 3. 50
DL: 1*1. 00
LL: 3. 50
DL: 1. 00 DL: 1. 00
DL: 1* 1. 00
DL: 1* 1. 00
DL: 1. 00 LL: 3. 50 LL: 3. 50
LL: 3. 50
DL: 1*1. 00
DL: 1*1. 00
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00 DL: 1. 00 DL: 1. 00DL: 1. 00
LL: 3. 50 LL: 3. 50 LL: 3. 50 LL: 3. 50LL: 3. 50
DL: 1* 1. 00
DL: 1. 00
DL: 1. 00 DL: 1. 00
DL: 1* 1. 00
DL: 1* 1. 00
LL: 3. 50
LL: 3. 50 LL: 3. 50
DL: 1*1. 00
DL: 1. 00
DL: 1. 00
LL: 3. 50
LL: 3. 50
第6层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
Figure 15-13 Sixth floor loads diagram
- 50 -
DL: 4*10. 00*0.
DL: 1. 00
L: 4*25. 00*0. 72
DL: 1*1. 00
DL: 1. 00
LL: 3. 50 DL: 1. 00
DL: 1*1. 00
DL: 1. 00 LL: 3. 50
DL: 4*15. 00*1. 50 LL: 3. 50
00
DL: 1*1. D
DL: 1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 DL: 1. 00
LL: 3. 50
DL: 4*15. 00*1. 50
DL: 1*1. 00
DL: 1*1. 00
DL: 1. 00 DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50 LL: 3. 50
DL: 1*1. 00
DL: 1. 00 DL: 1. 00
LL: 3. 50 LL: 3. 50
第7层梁、墙柱节点输入及楼面荷载平面图 [ 单位:kN、m]
说明:
1. 荷载工况: 恒载: DL, 活载: LL, 人防: ADV
2. [ ] 为楼板自重, { } 为楼梯荷载, BSW为梁自重, ARE为导荷面积, h为板厚
3. PMCAD布置的次梁荷载已经导算为墙或梁上集中荷载
4. 板上绿色标注为层间板相关信息
5. 梁上黄色标注为层间梁相关信息
6. 画图标注荷载含义详见荷载标注说明
Figure 15-14 Seventh floor loads diagram
- 51 -
3. Reinforcements Diagram
0. 35- 0. 97- 0. 07
( 0. 07)
( 0. 08)
( 0. 09) ( 0. 09)
0. 12- 0. 11- 0. 11 0. 12- 0. 11- 0.上
40
0. 12- 0. 11- 0. 16 0. 07- 0. 06- 0. 06 0. 26- 0. 27- 0. 13
0. 27- 0. 24- 0. 16
0. 28- 0. 25- 0. 16
0. 62 0. 52
上
0. 25
0. 13
0. 12
0. 27 0. 23
0. 15
0. 13
0. 29
0. 15
0. 17
0. 37
0. 25
0. 13
0. 13
0. 30 0. 26
0. 13- 0. 12- 0. 06
0. 18- 0. 17- 0. 07
0. 06- 0. 07- 0. 03 0. 19- 0. 22- 0. 07
0. 63- 0. 56- 0. 42
0. 27- 0. 24- 0. 18
0. 28- 0. 25- 0. 19
0. 57- 0. 51- 0. 36
0. 19- 0. 33- 0. 09
0. 65- 0. 58- 0. 36 0. 89- 0. 80- 0. 18 0. 72- 0. 64- 0. 31
0. 74- 0. 66- 0. 12
0. 09- 0. 11- 0. 02
0. 10- 0. 13- 0. 02
0. 61- 0. 54- 0. 10
0. 11- 0. 11- 0. 01
0. 15- 0. 14- 0. 02
0. 62- 0. 55- 0. 34 0. 85- 0. 76- 0. 18 0. 68- 0. 61- 0. 29
0. 74- 0. 66- 0. 25
0. 26- 0. 23- 0. 17
0. 27- 0. 24- 0. 17
0. 61- 0. 54- 0. 25
0. 19- 0. 33- 0. 09
0. 06- 0. 07- 0. 03 0. 11- 0. 13- 0. 05
0. 19- 0. 18- 0. 07
0. 26- 0. 25- 0. 09
0. 63- 0. 56- 0. 34 0. 87- 0. 77- 0. 18 0. 70- 0. 62- 0. 29
( 0. 13)
( 0. 09) ( 0. 28) ( 0. 54) 消能梁 ( 0. 46)
0. 14- 0. 13- 0. 07 0. 15- 0. 13- 0. 08
0. 30- 0. 27- 0. 220. 41- 0. 37- 0. 17
0. 35- 0. 0.
30-28-
0. 0.
1725- 0.0.18
63- 0. 47- 0.0.上
20
46-0.
0.0.
23-
00-
24-
0.
0.0.
0.
17-
2559-
18-
0.0.
0.
3149-
31 0. 32 0. 65- 0. 50- 0. 190. 30- 0. 27- 0. 17 0. 25- 0. 26- 0. 15
0. 17- 0. 15- 0. 03
0. 07- 0. 06- 0. 07
0. 07- 0. 06- 0. 07
0. 03- 0. 03- 0. 03
0. 03- 0. 03- 0. 03
0. 07- 0. 08- 0. 06
0. 18- 0. 16- 0. 09
0. 66 0. 43 0. 89 0. 67
0. 60- 0. 53- 0. 0.
上
0. 26
0. 18
0. 19
0. 30 0. 33 0. 64 0. 55
0. 19
0. 19
0. 38
0. 26
0. 18
0. 19
0. 33 0. 34 0. 67 0. 57
0. 26- 0. 24- 0. 09
17- 0. 06
0. 14- 0. 19- 0. 05 0. 15- 0. 0.
13-28-
0. 0.
1525- 0. 11 0. 40- 0. 36- 0. 05
0. 40- 0. 35- 0. 02 0. 39- 0. 40- 0. 09 0. 07- 0. 06- 0. 11
0715- 0. 13- 0. 03
1022- 0. 19- 0. 16
19-0.0.09
0.13-
0. 18 0. 18 0. 19- 0. 33- 0. 09
15-0.0.19
0. 12- 0. 15- 0. 05 0. 26- 0. 60- 0. 08
18- 0. 0.
0619- 0. 16- 0. 0.
0. 17 0. 17
0. 26 0. 27
0.31-
0. 15- 0. 14- 0. 02
21-0.0.09
35-0.0.28
0.17-
0.31-
0. 12- 0. 15- 0. 05 0. 26- 0. 58- 0. 08 0. 05- 0. 05-
上 0. 09
0. 13- 0. 12- 0. 08
35-0.0.16
0.0.06
1219- 0. 16- 0. 0.
上 上
20-
0433- 0.0.29-
0319- 0.0.17-
0. 20- 0. 17- 0. 0.
0315- 0. 13- 0. 0.
0. 18 2319- 0. 16- 0. 0. 0. 18
0. 17 0. 17
0. 18- 0. 18- 0. 07
0. 27 0. 27
0. 13- 0. 16- 0. 05 0. 06- 0. 05-0.
0. 25-
10 0. 23- 0. 08 0. 30- 0. 45- 0. 08
0. 07- 0. 07- 0. 04
0. 11- 0. 10- 0. 07
0. 20- 0. 17- 0. 08
0. 17- 0. 15- 0. 0.
0. 38- 0. 33- 0. 0.
( 0. 09)
( 0. 42) ( 0. 48) 消能梁 ( 0. 57)
0. 30- 0. 28- 0. 15 0. 26- 0. 23-0.
0. 32-
15 0. 26- 0. 16
0. 53- 0. 42-
上0.0.38-
180. 00-0.0.49-
220. 43- 0. 27 0. 54- 0. 43- 0. 17 0. 26- 0. 27- 0. 16
0. 59 0. 77 0. 77
上
0. 30
0. 19
0. 17
0. 47 0. 56 0. 63
0. 17
0. 17
0. 35
0. 30
0. 19
0. 17
0. 50 0. 59 0. 65
- 52 -
0. 34- 0. 95- 0. 07 0. 04- 0. 03- 0. 02
0. 29- 0. 26- 0. 13
0. 02- 0. 02- 0. 01
( 0. 04)
( 0. 05)
( 0. 02) ( 0. 03)
0. 10- 0. 08- 0. 09 0. 09- 0. 08- 0. 03
0. 09- 0. 08- 0. 02 0. 12- 0. 11- 0. 09上0. 15- 0. 13- 0. 09 0. 20- 0. 20- 0. 15
0. 10- 0. 09- 0. 04
0. 21 0. 22
上 0. 09
0. 03
0. 02
0. 02
0. 08
0. 15
0. 17
0. 33
0. 18
0. 21
0. 40
0. 03
0. 02
0. 02
0. 08 0. 09
0. 17- 0. 16- 0. 08
0. 25- 0. 24- 0. 10
0. 11- 0. 14- 0. 04
0. 47- 0. 43- 0. 20
0. 06- 0. 06- 0. 03
0. 20- 0. 18- 0. 12
0. 10- 0. 09- 0. 04
0. 36- 0. 63- 0. 17
0. 15- 0. 14- 0. 07 0. 19- 0. 18- 0. 03 0. 18- 0. 17- 0. 07
0. 24- 0. 21- 0. 04
0. 05- 0. 05- 0. 02
0. 06- 0. 07- 0. 02
0. 26- 0. 23- 0. 06
0. 25- 0. 92- 0. 05
0. 17- 0. 16- 0. 02
0. 25- 0. 24- 0. 03
0. 15- 0. 13- 0. 07 0. 19- 0. 18- 0. 03 0. 18- 0. 16- 0. 07
0. 24- 0. 21- 0. 07
0. 09- 0. 09- 0. 03
0. 13- 0. 12- 0. 04
0. 26- 0. 23- 0. 10
0. 36- 0. 63- 0. 17
0. 05- 0. 05- 0. 03 0. 10- 0. 12- 0. 05
0. 29- 0. 27- 0. 10
0. 42- 0. 40- 0. 15
0. 14- 0. 13- 0. 06 0. 17- 0. 17- 0. 02 0. 17- 0. 15- 0. 06
( 0. 09)
( 0. 02) ( 0. 21) ( 0. 41) ( 0. 39)
0. 18- 0. 20- 0. 08
0. 18- 0. 20- 0. 08
0. 16- 0. 18- 0. 07
0. 17- 0. 18- 0. 08
0. 18- 0. 19- 0. 08
0. 18- 0. 20- 0. 08
0. 18- 0. 20- 0. 08
0. 23- 0. 26- 0. 08
0. 32
0. 20
0. 22
0. 07 0. 25 0. 49 0. 49
0. 15
0. 16
0. 34
0. 07 0. 26 0. 50
0. 34
0. 22
0. 24
0. 49
0. 42- 0. 40- 0. 15
0. 22- 0. 22- 0. 070. 22- 0. 20-
0. 20-
0. 08
0.
0. 26-
18-
0.0.
0.
34-
23-
17
0.
0.0.
40-
30-
130.
0. 36-
11 0.0.0747- 0. 42- 0. 04 0. 47- 0. 43- 0. 06 0. 33- 0. 29-
0. 0.
14-11
0. 13- 0. 14
0. 21-
23-
010. 01- 0. 01
020. 01- 0. 01
16
0.19-
0. 12- 0. 15- 0. 05 0. 30- 0. 43- 0. 08 0. 30- 0. 26- 0. 0.
0522- 0. 19- 0. 10
0. 16 0. 17
0918- 0. 0.
20-0.
0. 36- 0. 63- 0. 17
21-0.0.
0. 15 0. 16
24-0.0.22-
23-0.0.05
26
0. 22 0. 23
10- 0. 09- 0. 04
11- 0. 10- 0. 04
03- 0. 03-0.0.02-
02- 0. 02-0.0.01-
0. 24- 0. 23- 0. 07 0. 25- 0. 23- 0. 0.
0224- 0.0.21-
23-0.0.03
20- 0. 0.
0515- 0. 14- 0. 07
0. 25- 0. 24- 0. 03
0. 0.
20-
36-
0.0.06
20-
0.0.23
18-
23-0.
0. 11- 0. 10- 0. 05
0. 11- 0. 10-
0. 04-
0. 04
0. 04- 0. 05
0. 02- 0. 02- 0. 02
0. 01- 0. 01- 0. 01
40-0.
0.
21-0.0.08
19-
35-
上 上
0.07
上 上
0.18
21-0.0.
0. 20- 0.0.18-
0. 04
0. 04
0. 01
0. 02
40-0.0.
0. 17- 0. 23- 0. 06 0. 06- 0.0.05-
18-0.0.07
17- 0. 0.
0518- 0. 18- 0. 06
19-
0. 10- 0. 09- 0.
0. 11- 0. 10- 0.
0. 03- 0. 03- 0.
0. 02- 0. 02- 0.
25-
0.0.09
0.0.12
21-0.
0. 13- 0. 12- 0. 05
0. 12- 0. 11-
0. 05-
0. 04
0. 04- 0. 05
28-0.
0. 18-
0. 17- 0. 15- 0. 04
0421-
0. 36- 0. 63- 0. 17
0. 16
0.
0. 32- 0. 31- 0. 09 0. 36- 0. 33- 0. 0.
0336- 0.0.32-
35-0.0.03
31- 0. 0.
0625- 0. 23- 0. 11
0.
0.0.
0. 16 0. 17
0. 20-
24-
0. 14 0. 15
19- 0. 17-
26- 0.0.23-
0. 25- 0. 24- 0. 10
0. 22 0. 23
0. 17- 0. 15- 0. 05
0. 17- 0. 18- 0. 04
0. 13- 0. 14- 0. 05
0. 28- 0. 30- 0. 06
0. 19- 0. 22- 0. 04
( 0. 06)
( 0. 35) ( 0. 44) ( 0. 51)
0. 18- 0. 17- 0. 09 0. 20- 0. 18- 0. 0.
0316- 0.0.14-
17-0.0.04
0.
15-26-
0. 0.
0623-
0.0.25-
上 080. 22- 0. 08
0. 17- 0. 16- 0.0.06
19- 0.
0. 16-
19-0.0. 02
17- 0. 02 0. 31- 0. 32- 0. 20
0. 44 0. 77 0. 72
上 0. 26
0. 16
0. 13
0. 37 0. 54 0. 59
0. 21
0. 23
0. 47
0. 40 0. 56 0. 60
0. 26
0. 15
0. 13
第 2 层混凝土构件配筋及钢构件应力比、下翼缘稳定验算应力简图( 单位: cm*cm)
本层: 层高 = 4000 ( mm) 梁总数 = 175 柱总数 = 23 支撑总数 = 10
墙总数 = 0 墙柱总数 = 0 墙梁总数 = 0
钢号: 梁 Q345 柱( 含支撑) Q345
( DPL代表大偏拉, XPL代表小偏拉, PL代表大\ 小偏拉并存)
- 53 -
( 0. 02)
( 0. 02)
0. 09- 0. 09- 0. 09
0. 12
0. 15
0. 30
0. 10
0. 12
0. 22
0. 11- 0. 11- 0. 06
0. 11- 0. 11- 0. 05
0. 11- 0. 15- 0. 05
0. 11- 0. 11- 0. 02
0. 11- 0. 11- 0. 01
0. 11- 0. 15- 0. 05
0. 21- 0. 20- 0. 07
0. 19- 0. 18- 0. 07
0. 12- 0. 17- 0. 04
( 0. 03)
( 0. 16) ( 0. 36) ( 0. 33)
0. 35- 0. 33- 0. 20 0. 27- 0. 30- 0. 07 0. 25- 0. 22- 0. 02 0. 24- 0. 23- 0. 06 0. 30- 0. 上
26- 0. 09 0. 21- 0. 22- 0. 12
0. 34- 0. 39- 0. 07
0. 29- 0. 35- 0. 08
17- 0. 16- 0. 14
0. 34 0. 75 0. 56
上 0. 47
0. 33
0. 21
0. 22
0. 21 0. 39
0. 10
0. 09
0. 23
0. 36
0. 23
0. 25
0. 20 0. 47 0. 39
0. 19- 0. 18- 0. 07
05- 0. 04- 0.0.02
09- 0.0.04
0. 13- 0. 18- 0. 05 0. 30- 0. 36- 0. 08 0. 30- 0. 29- 0. 06 0. 11- 0. 10- 0. 10
0. 05
10-0.
0. 09-
0. 11- 0. 14- 0. 05 0. 26- 0. 25- 0. 08 0. 26- 0. 28- 0. 04 0. 15- 0. 14- 0. 07
0. 04- 0.0.03
0. 16- 0.0.07
0. 11
0.
0. 19 0. 25
0. 10-
0. 10- 0. 09-
0. 29 0. 38
0. 06
0. 05
0. 11- 0. 11- 0. 01
0. 05-
0. 18-
04-
15-
0. 12- 0. 11- 0. 05
0. 12- 0. 11-
0. 05-
0. 04
0. 04- 0. 05
0. 02- 0. 02- 0. 02
0. 01- 0. 01- 0. 01
04-0.0.05
0. 08- 0. 11
上 上
上 上
0204- 0.0.04-
0.0.16-
0. 08
0. 05
0. 17-
0. 10-
0. 13- 0. 12- 0. 05
0. 12- 0. 11-
0. 05-
0. 04
0. 05- 0. 05
1316-
0409-
0. 06- 0. 05- 0. 0.
0. 11- 0. 15- 0. 05
0. 0.
0. 0.
17-
0. 20 0. 26
11-
15-
09-
0. 11- 0. 11- 0. 05
0. 19 0. 25
0. 14
0.
10- 0. 0.
0. 29 0. 38
17-0.
2314-
0. 20- 0. 19- 0. 0.
0720- 0. 19-
0. 0.
10-050. 09- 0. 07
0. 08- 0. 07- 0. 05
0. 33- 0. 37- 0. 07
0. 08- 0. 09- 0. 02
0. 27- 0. 29- 0. 06
0. 26- 0. 29- 0. 07
( 0. 02)
( 0. 29) ( 0. 38) ( 0. 43)
0. 29- 0. 12- 0. 0.
0924- 0. 08-
0. 0.
26-
050. 09-0.0. 20-
05 0. 18- 0. 02 0. 24- 0. 23- 0. 06 上 0. 18- 0. 19- 0. 06 0. 14- 0. 13- 0. 02 0. 27- 0. 28- 0. 14
0. 46 0. 65 0. 63
上
0. 22
0. 13
0. 12
0. 33 0. 45 0. 48
0. 17
0. 16
0. 39
0. 21
0. 12
0. 11
0. 34 0. 47 0. 49
- 54 -
0. 12- 0. 17- 0. 04
0. 10- 0. 09- 0. 05
0. 10- 0. 09- 0. 05
( 0. 15) ( 0. 36) ( 0. 31)
0. 29- 0. 32- 0. 06
0. 26
0. 12
0. 11
0. 19 0. 39
0. 29
0. 14
0. 12
0. 20 0. 50 0. 42
0. 17 0. 20
0. 17 0. 20
0. 22-
0. 24-
0. 31 0. 37
0. 12- 0. 15- 0. 05 0. 30- 0. 71- 0. 09
0106- 0. 0.
19-0.
0416-0.
0.0.06
0. 0.
10- 0. 09- 0. 04
10- 0. 09- 0. 04
23-
28-
0. 23- 0. 23- 0. 07 0. 24- 0. 23- 0. 02 0. 24- 0. 23- 0. 07
0. 0.
19-
16-
0.0.07
12-
0. 04
0.
06-
23-0.
0. 12- 0. 11- 0. 05
0. 11- 0. 10-
0. 04-
0. 04
0. 04- 0. 05
0. 02- 0. 02- 0. 02
0. 01- 0. 01- 0. 01
28-0.
0.
12-0.0.02
17-
0. 15-
0.08
21-0.0.
0. 11- 0.0.06-
0. 04
0. 04
0. 06
0.
0. 17- 0. 23- 0. 06 0. 17- 0. 23- 0. 06
0. 26-
17-
0. 10- 0. 09- 0.
0. 10- 0. 09- 0.
0.0.10
25- 0. 14-
20-0.
0. 13- 0. 12- 0. 05
0. 12- 0. 11-
0. 05-
0. 04
0. 04- 0. 05
0. 15-
0. 11- 0. 06- 0. 04
0. 14
0. 12
0.
0. 25- 0. 25- 0. 08 0. 27- 0. 25- 0. 02 0. 26- 0. 25- 0. 08
0. 19-
20- 0. 09- 0.
18- 0. 16-
0. 17 0. 20
0. 22- 0. 16- 0. 15
0. 09
0. 04
0. 14
0. 24 0. 42 0. 44
0. 40
0. 19
0. 18
0. 26 0. 46 0. 47
第 4 层混凝土构件配筋及钢构件应力比、下翼缘稳定验算应力简图( 单位: cm
本层: 层高 = 4500 ( mm) 梁总数 = 62 柱总数 = 15 支撑总数 = 9
墙总数 = 0 墙柱总数 = 0 墙梁总数 = 0
钢号: 梁 Q345 柱( 含支撑) Q345
( DPL代表大偏拉, XPL代表小偏拉, PL代表大\ 小偏拉并存)
- 55 -
0. 12- 0. 17- 0. 04
0. 10- 0. 09- 0. 05
0. 10- 0. 09- 0. 05
( 0. 08) ( 0. 30) ( 0. 24)
39 0. 27- 0. 44
35 0. 24- 0. 39
0. 44- 0. 41- 0. 24 0. 22- 0. 22- 0. 07 上
0. 53 0. 83 0. 57
上 上 0. 48 上
CXB
0. 92
0. 28
0. 13
0. 22 0. 36
CXB
1. 10
0. 33
0. 17
0. 22 0. 55 0. 44
0. 30-
0. 28-
0. 16- 0. 25- 0. 05 0. 24- 0. 61- 0. 06
47-0.
0748- 0. 41-0.
53-0.0.03
0. 14- 0. 22
0. 14- 0. 22
0. 36- 0. 32- 0. 39 0. 58- 0. 52- 0. 17 0. 58- 0. 52- 0. 17 0. 36- 0. 32- 0. 39
0.0.47-
0. 03
0. 38- 0. 34- 0. 0.
0. 52-
0. 21
0. 21
0. 52- 0. 46-
0. 16-
0. 16-
07- 0. 07- 0. 02
07- 0. 07- 0. 02
0. 12 0. 12- 0. 11- 0.0.06
16- 0. 14- 0.0.02
16- 0. 14- 0.0.02
14- 0. 12- 0. 06 0. 14
21-
21-
24-0.0.21
24-0.0.21
0. 18 0. 21
0.
0. 60-
51 0. 54- 0. 25
0. 65- 0. 58-
0. 32-
0. 31
0. 29-0.0.10-
490. 14- 0. 03 0. 09- 0. 10- 0. 030. 70
0. 19- 0. 17- 0. 18
0. 18- 0. 16- 0. 18
0. 39- 0. 130. 50- 0. 44- 0. 08
29-
29-
CXB CXB
13
13
33-0.0.0.
33-0.0.0.
0. 07- 0. 07- 0.0.02
29-
13
13
33-0.0.0.
33-0.0.0.
0. 12
0. 56- 0. 50- 0. 24
0. 62- 0. 55-
0. 30-
0. 30
0. 27-0.0.09-
460. 11- 0. 03 0. 08- 0. 11- 0. 03 0. 14
0.0.24-
0.0.24-
0. 18 0. 21
0. 53 0. 70
0. 31
0. 31
5. 49- 4. 90- 2.
11.23
65- 10. 40-11.
2. 20
66- 10. 41-5.2.75-
20 5. 13- 2. 23
0. 27-
0. 27-
CXB CXB
0. 22- 0. 20-
0. 22- 0. 20-
0. 13
0. 44-
28-
0. 52- 0. 46- 0. 34
0. 19- 0. 28- 0. 05
32-0.0.50
0. 29- 0. 25- 0. 43
0. 29- 0. 26- 0. 32 0. 30- 0. 27- 0. 01 0. 30- 0. 27- 0. 01 0. 29- 0. 26- 0. 32
0. 31- 0.0.28-
( 0. 13) ( 0. 36) ( 0. 30)
上 0. 54 0. 29- 0. 27- 0. 15 0. 86
0. 16- 0. 07- 0. 05 0. 21- 0. 12- 0. 06 上上
0. 61
上 0. 53
CXB
1. 22
0. 37
0. 16
0. 25 0. 42
CXB
1. 28
0. 38
0. 18
0. 27 0. 61 0. 51
第 5 层混凝土构件配筋及钢构件应力比、下翼缘稳定验算应力简图( 单位: cm
本层: 层高 = 6000 ( mm) 梁总数 = 76 柱总数 = 14 支撑总数 = 8
墙总数 = 0 墙柱总数 = 0 墙梁总数 = 0
钢号: 梁 Q345 柱( 含支撑) Q345
( DPL代表大偏拉, XPL代表小偏拉, PL代表大\ 小偏拉并存)
超限类别: CXB - - - 长细比
- 56 -
0. 12- 0. 17- 0. 04
0. 10- 0. 09- 0. 05
0. 10- 0. 09- 0. 05
( 0. 04) ( 0. 07) ( 0. 04)
110. 26- 0. 23
100. 26- 0. 20
0. 33- 0. 30- 0. 19 0. 19- 0. 30- 0. 07
0. 30 0. 35 0. 27
0. 21 0. 19 0. 18
0. 25 0. 28 0. 23
0. 21- 0. 20- 0. 05
08-0.0.32-
0313- 0. 12-0.0.29-
0. 14- 0. 19- 0. 05 0. 22- 0. 51- 0. 06 0. 06- 0. 05- 0. 07
12-0.0.04
0. 17- 0. 15- 0. 08 0. 22- 0. 29- 0. 03 0. 18- 0. 0.
16-06-
0. 0.
0705- 0. 09
020.0.10-
0. 12- 0. 10- 0. 0.
14-
0. 0.
0. 15- 0. 12-
0. 11- 0. 10- 0. 05
0. 11- 0. 10-
0. 04-
0. 04
0. 04-
0. 0.
04-050. 04- 0. 03 0. 08- 0. 0.
07-08-
0. 0.
0407- 0. 06
0. 02- 0. 02- 0. 02
0. 01- 0. 01- 0. 01
100. 08- 0. 080. 15- 0. 12- 0. 03
0. 08- 0. 08- 0. 05
0. 12- 0. 11- 0. 05
0. 12- 0. 11-
0. 05-
0. 04
0. 04-
0. 0.
04-050. 04- 0. 03 0. 05- 0. 0.
04-05-
0. 0.
0304- 0. 03
11-
0. 0.
07-
0. 31- 0. 27- 0. 12
0. 15- 0. 21- 0. 05
10-0.0.21
0. 27- 0. 24- 0. 16
0. 20- 0. 17- 0. 08 0. 25- 0. 34- 0. 03 0. 20- 0. 18- 0. 08
0. 31- 0.0.25-
( 0. 06) ( 0. 09) ( 0. 07)
0. 21- 0. 19- 0. 11 0. 15- 0. 24- 0. 05
0. 28 0. 34 0. 26
0. 23 0. 19 0. 22
0. 20 0. 26 0. 21
第 6 层混凝土构件配筋及钢构件应力比、下翼缘稳定验算应力简图( 单位: cm
本层: 层高 = 2500 ( mm) 梁总数 = 61 柱总数 = 6 支撑总数 = 0
墙总数 = 0 墙柱总数 = 0 墙梁总数 = 0
钢号: 梁 Q345 柱( 含支撑) Q345
( DPL代表大偏拉, XPL代表小偏拉, PL代表大\ 小偏拉并存)
- 57 -
110. 29- 0. 18
31- 0. 32
( 0. 02) ( 0. 04) ( 0. 02)
0. 29- 0. 31- 0. 06
09 0. 23- 0. 18
0. 19- 0. 18- 0. 10
0. 12- 0. 11- 0. 06 0. 16- 0. 19- 0. 07
0. 32 0. 49 0. 27
35-0.0.23
01- 0. 02
01- 0. 02
0. 22 0. 33 0. 18
0. 0.
0. 05- 2304-
0. 05-
0. 04
0.0.04-
05-0.0.0.
01
04- 03- 0.0.0434
04-0.0.02 0. 20
0.0.32-
12-
130.0.0.18
01-0.0.02
02-0.0.02
02 0. 12-0.0.25-
0715- 0. 14- 0.0.0416- 0. 14- 0.0.0719- 0. 17-
0. 21- 0. 19- 0. 07 0. 23- 0. 35- 0. 06
13-
20-
0. 01- 0.0.01-
0. 02- 0.0.01-
0.0.0.
20-
0. 05- 0. 04-
0. 05-
0. 04
0.0.05-
05-0.0.0.
01
05-
04-0.0.03
04- 0.
0. 29-
05 0. 26- 0. 12
22-06
0. 30- 0. 39- 0. 04 0. 20- 0. 18- 0. 09
0. 14-
0. 06- 0. 06- 0. 03
0.0.0.
14- 0. 13- 0. 09
23-
0. 14- 0. 12-0.
0.0.25-
0. 03
0. 28-
0. 30- 0. 37- 0. 09
25-
0. 04- 0. 04- 0. 03
28-0.0.04
03 0. 13- 0.0.01
08- 0. 07- 0. 01
12- 0. 10- 0. 03
0. 04- 0. 04- 0. 02
08 0.0.24-
0. 30- 0. 38- 0. 09 0. 04- 0. 04- 0. 02
1224- 0. 21-0.0.27-
0513- 0. 12-0.0.14-
1014- 0. 13- 0. 0.
0. 06- 0. 05- 0. 03
10- 0. 09- 0. 06
17- 0. 15- 0. 0.
13- 0. 12- 0. 0.
0. 09- 0. 08- 0. 0.
0. 14
0. 23
0. 15
0. 12- 0. 17- 0. 04 0. 22- 0. 19- 0. 09 0. 26- 0. 34- 0. 03 0. 20- 0. 17- 0. 09
0. 30- 0. 27- 0.
0. 33- 0. 29- 0.
0. 24- 0. 21- 0.
( 0. 03) ( 0. 05) ( 0. 03)
0. 11- 0. 11- 0. 06 0. 11- 0. 18- 0. 05
0. 26 0. 42 0. 23
0. 22 0. 31 0. 17
0. 16 0. 27 0. 17
- 58 -
4. Diagram of Beam Elastic Deflection
-2. 13
-1. 88
10. 23
上
0. 39 上 0. 13
0. 14 0. 34
11. 40
12. 01
5. 24
4. 24
0. 13 0. 68
2. 09
2. 31
10. 38
20. 15
21. 29
8. 24
2. 48
2. 55
9. 259. 34
0105
2. 40
21. 23
21. 94
10. 52
12.12.
12. 37
14. 43
1. 93
1. 87
18. 58
19. 57
9. 96
9. 25
6. 75
11. 67
0. 12 13. 65 0. 40 2. 48
14. 23
15. 48
2. 74
4. 17
- 0. 04 - 0. 07 上 - 0.- 19
0.- 0.
2019 - 0. 08
10. 16
0. 06
11. 91 0. 30 0. 140. 160. 14 上 0. 03 0. 59
- 0. 20
13. 92
0. 07
0. 08
0. 05
0. 05
0. 07
0. 060. 07
- 0. 84
0. 23
0. 77
2. 60
6. 12
0. 06
1. 87
1. 19 10. 10. 62
10. 73
73
0. 74 2. 48
- 0. 04-0. 01 - 0. 06
0. 17 -0. 01- 0. 09
7. 14
1. 85
上 上
上 上
2. 54
1. 88
0. 74 1. 05
7. 30
0. 21
2. 29
1. 68
0. 74 1. 44
2. 48
7. 58
3737
0. 13
0. 82
0. 0.
0. 74 1. 07
0. 09
0. 16
6. 28
8. 18
- 0. 04
上 - 0. 21
0. 23 0. 060. 08 上 0. 07 0. 67
- 59 -
0. 94
0. 83
- 0. 01
0. 04
9. 54
上
上 0. 08 0. 71
1. 00 1. 46 1. 19
1. 46
3. 39
0. 13
3. 17
4. 57
3. 41
5. 58
6. 15
3. 52
2. 65 3. 20 4. 68
3. 66
3. 54
4. 97
4. 16
9. 33
1314
6. 47
7. 08
4. 13
4. 4.
2. 62 3. 15
3. 61
2. 72
3. 59
3. 10
5. 53
6. 21
2. 88
0. 12 0. 40
4. 68
1. 21
3. 73
4. 33
0. 89
2. 40 3. 31 2. 89
- 0. 02 - 0. 12 - 0. 23 - 0. 54 - 0. 49
-上0. 52 - 0. 26 - 0. 07
0. 01 0. 140. 17 0. 18
0. 0.
2222
0. 20 上 0. 63
0. 30
0. 26
0. 25
0. 26
0. 28
0. 30
0. 30
0. 28
0. 11
1. 42
0. 41 0. 36
1. 25 1. 17
3. 95 3. 26
5. 54
7. 96
2. 95
0.0.2832
8. 80
3. 59
10. 08
0. 74
13. 65
- 1. 85
- 1. 52
68 3. 55
0. 06
4. 97
- 0. 04
4. 68
7. 45
8. 43
- 0. 02
3. 59 3.3.68
上 4. 04 上
上 0. 0.7273 0. 26 上
4. 96
6. 48 6. 16
6. 49
- 0. 61
- 0. 33
7. 17
0. 03
0. 02
0. 33
0. 34
0. 05
1. 16
0. 08
2. 77 3. 22
0. 40
4. 55
0. 0.7878 0. 28 6. 47
0. 51
9. 38
9. 90
4. 68
0. 560. 61
2021
5. 95
1. 42
0. 0.
9. 06 8. 95
9. 39
0. 79 10. 19
2. 02
0. 27
0. 22
0. 43
0. 23
3. 72
5. 20
6. 99
- 0. 10 上8. 20- 0. 11
- 0. 08
0. 07 0. 20 0. 15 上 20 0. 16
0.0.20 0. 71
- 60 -
0. 57
2. 11
2. 01
1. 25
2. 36
2. 19
1. 82
1. 58
1. 25
0. 13
- 0. 20
0. 92
- 0. 18 上
上 0. 26 0. 44
2. 37 2. 26
0. 71
0. 54
0. 08
1. 29
0. 25
0. 69
1. 93
0. 10
33
0. 09
2. 16
0.0.33
0. 30
1. 58
7. 91 7. 76
0. 69
3. 81 1. 25
6. 69 7. 25
0. 01
78
78
2.2.78
1. 24
0. 361. 19
上 上
0.0.7575 0. 27
2.
上 0. 06 上
2. 18
0. 03
0. 02
1. 62
0. 11
2. 122. 43
0. 38
2. 00
0.0.7575 0. 27
0. 42
1. 25
0. 43
0. 13 0. 15
4. 13
9920
7. 25
0. 31
7. 86
0. 1.
1. 051. 11 0. 43
0. 65
0. 13
1. 85
0. 39
0. 33
4. 89
7.上64
0. 04 0. 09 0. 06 0. 0.
2221 上 0. 130. 11 0. 82
- 61 -
- 0. 35
0. 18
0. 92
- 0. 24 上
上 上 上
1. 53
0. 45
3. 08 3. 08
0. 35
1. 32
1. 30
0. 71
6. 39
0. 94
2. 68
2. 89
10. 29
0. 74
243. 17
6061 3. 51
8. 56
1.3130
3.3.24
3. 46 3.3.
1.1.32
0. 0.7273 0. 26
6. 38 7. 06 6. 38
0. 03
0. 02
3. 09
0. 33
0. 33
1. 16 1. 16
1. 17
2. 26 2. 70
0. 0.7878 0. 28
2. 54
0. 48
1. 07
1. 17
6. 94 7. 67 6. 94
0. 79
6. 49
上 上 上 - 0. 20 上
0. 17 0. 24 上
- 62 -
- 1. 71
- 2. 40
0. 92
上
上 0. 23 上 上
2. 23
2. 56
2. 66
2. 27
0. 71 6. 02
4. 25
3. 61
5. 70
4. 61
3. 39 5. 56 3. 39
0. 74
1. 06 0. 76
1. 06 0. 76
1. 33 1. 95 1. 38
7. 77
5. 25
4. 33
7. 85
3.3.6371 1. 47 0. 13 0. 13
0. 18
0. 17
1. 27
0. 15
0. 16
1. 27
7. 04
4. 67
0. 87 1. 13
0. 87 1. 13
3. 83
3.3.4250 1. 39 0. 13 0. 13
3. 10
59
2.2.44
2. 04
0. 79
2. 26 3. 37 2. 26
87. 01 90. 34
- 63 -
0. 23
0. 92
- 0. 08
0. 06
1. 12
0. 38
1. 07
0. 95
0. 09
0. 71 0. 94
2. 27 1. 87
1. 58
5. 81
1. 12
0. 95
3. 96 4. 02
0. 74
6. 86
2. 13
2827
2. 72
0. 80
0. 86
2. 12
1.1.
0.0.
7273 0. 26 0. 08 0. 13
0. 16
0. 03
0. 02
0. 87
0. 94
0. 14
1. 10
2. 21
0. 80
0. 86
1. 68
0.0.
7878 0. 28 0. 08 0. 08
0. 10
0. 42
0. 81
0. 60
0. 48
0. 79
4. 22 4. 23
- 0. 02 7. 29
0. 96
- 64 -
- 0. 04
1. 43 1. 73
0. 45
0. 50
1. 10
0. 01 0. 070. 06
0. 07
2. 09
1. 02
0. 01
0. 01
1. 58
26
3.34
1. 66
5. 23
3.
0. 01 0. 070. 06
0. 07 6. 56
5. 55 5. 03
2. 28
53 4. 43
9. 04
2120
0. 67
2. 2.
4.4.53
1. 53
0. 08
3. 53
2. 33 2. 40
0. 07
65
0. 860. 88
4. 29
1.1.65
1. 97
0. 07
3. 38 0. 08
1. 66
2. 98
1. 12
0. 63
1. 46
0. 08 0. 08
2. 91
0. 65
1. 20
0. 58
0. 66
4. 61 4. 49
- 0. 02
7. 83
1. 13
- 65 -
FRAME 1
FOUNDATION CALCULATION REPORT
目 录
1. 模型基本简图 ................................................................................................................................................... 2
2. 承载力计算结果 ............................................................................................................................................... 5
3. 配筋计算结果 ................................................................................................................................................... 7
4. 弯矩计算结果 ................................................................................................................................................... 8
5. 设计简图结果 .................................................................................................................... 错误!未定义书签。
1. 模型基本简图
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0
模型信息 MODEL
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
图 4-1
20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0
20000. 0
20000. 20000.
0 0
20000. 0 20000. 020000. 0 20000. 0
20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0
20000. 0
20000. 0 20000. 0
20000. 0 20000. 0 20000. 0
图 4-2 基础荷载
LOAD (KN)
-4-
pk, max=128. 0( 12)
pk, avg=97. 0( 10)
104. 1( 12) 102. 5( 12) 102. 2( 12) 103. 1( 12) 101. 3( 9) 97. 0( 9)
[ 1. 2*125]
[ 1* 125]
pk, avg=108. 0( 8)
90. 0( 12) 88. 9( 12)
96. 3( 9)
103. 6( 9) 104. 6( 9)
99. 5( 9) [ 1*125]
pk, max=141. 0( 8)
83. 5( 7) 88. 6( 9) 104. 9( 9) 106. 0( 9)
[ 1. 2*125]
97. 8( 9) 101. 0( 9)
无震最大反力 No Seismic action maximum reaction force
pk, avg=95. 0( 9)
[ 1*125]
pk, max=106. 0( 9)
[ 1. 2*125]
pk, avg=100. 0( 8)
pk, max=139. 0( 8)
113. 4( 10) 118. 2( 10) 123. 3( 10) 128. 0( 10) 128. 0( 10) 120. 3( 10) 108. 6( 12)
[ 1. 2*125]
113. 1( 7) 115. 4( 7) 119. 3( 10) 125. 2( 10) 125. 3( 10)116. 6( 10) 103. 8( 6) pk, avg=118. 0( 6) [ 1* 125]
[ 1*125]
113. 1( 7) 115. 5( 7) 119. 4( 11) 125. 3( 11) 125. 4( 11)116. 7( 11) 103. 9( 6)
pk, max=144. 0( 13)
[ 1. 2*125]
113. 7( 11) 118. 4( 11) 123. 5( 11) 128. 2( 11) 128. 2( 11) 120. 5( 11) 108. 6( 13)
-5-
pk, avg=113. 4( 7)
[ 1*125]
pk, max=128. 2( 11)
[ 1. 2*125]
103. 6( 8) 105. 7( 8) 106. 6( 8)
99. 1( 9) 106. 9( 9) 111. 7( 9) 110. 7( 9) 105. 2( 9)
89. 9( 10) 93. 5( 7)
109. 9( 8) 113. 0( 8) 113. 8( 8) 99. 3( 4) 99. 6( 4)
114. 3( 113.
9) 4( 9)
113. 5( 9)
99. 5( 9) 107. 8( 9) 105. 7( 9)
96. 2( 11) 96. 2( 11) 112. 2( 9) 110. 6( 8) 114. 2( 8) 115. 0( 8) 88. 8( 4) 89. 5( 2)
114. 1( 9)
图 4-3
107. 6( 13)107. 2( 13)106. 9( 13)108. 3( 13) 110. 9( 9) 109. 8( 9) 104. 4( 9)
104. 2( 8) 106. 5( 8) 107. 6( 8) 93. 6( 5) 93. 1( 5)
104. 2( 13)103. 7( 13)
pk, avg=101. 4( 9) 101. 8( 13)103. 4( 13) 103. 5( 13)
[ 1*125]
pk, max=114. 3( 9)
[ 1. 2*125] pk, avg=86. 9( 2)
pk, avg=106. 7( 8) [ 1*125]
[ 1*125] pk, max=104. 2( 13)
pk, max=115. 0( 8) [ 1. 2*125]
2. 承载力计算结果
[ 1. 2*125]
pk, max=145. 0( 20)
pk, avg=99. 0( 20)
[ 1. 2*137. 5]
98. 5( 20) 98. 5( 20) 99. 6( 20) 101. 6( 20) 99. 7( 20) 93. 7( 20)
[ 1*137. 5]
-6-
pk, avg=103. 6( 19)
[ 1*137. 5]
pk, max=121. 7( 21)
[ 1. 2*137. 5]
97. 9( 18) 100. 0( 18) 101. 0( 18)
93. 6( 19) 100. 6( 19) 105. 0( 19)104. 1( 19)99. 3( 19)
81. 3( 20) 86. 9( 19)
103. 7( 18)106. 7( 18) 107. 6( 18) 111. 1( 20)114. 8( 20)
107. 2( 106.
19) 4( 19)
106. 4( 19)
94. 0( 19) 101. 3( 19) 99. 4( 19)
90. 4( 21) 91. 1( 21) 105. 2( 19) 104. 3( 18)107. 8( 18) 108. 7( 18) 90. 6( 20) 94. 6( 20)
106. 8( 19)
图 4-4
101. 0( 21)101. 6( 21)102. 4( 21)104. 8( 21) 106. 1( 21)103. 2( 21) 98. 0( 19)
99. 2( 21) 100. 7( 18) 102. 0( 18) 102. 1( 21)97. 9( 21)
123. 3( 21)118. 9( 21)
pk, avg=95. 7( 19) 104. 4( 21)105. 3( 21) 104. 2( 21)
[ 1* 137. 5]
pk, max=107. 2( 19)
[ 1. 2*137. 5] pk, avg=88. 1( 18)
pk, avg=101. 0( 18) [ 1*137. 5]
[ 1*137. 5] pk, max=123. 3( 21)
pk, max=108. 7( 18) [ 1. 2*137. 5]
[ 1. 2* 137. 5]
3. 配筋计算结果
9( 28)
9( 0)
10( 29)
10( 0)
10( 29)
10( 0)
9( 35)
9( 26)
10( 35)
10( 31)
10( 34)
10( 41)
9( 34)
9( 32)
9( 0)
9( 34)
9( 34)
9( 35)
9( 34)
9( 31)
9( 26)
9( 35)
9( 26) 9( 0) 9( 26) 10( 0) 10( 0) 10( 0) 10( 0)
9( 35) 9( 33) 9( 33) 10( 33) 10( 29) 10( 29) 10( 32) 9( 35) 9( 27)
9( 32)
9( 29)
9( 27)
9( 35)
9( 33)
9( 32)
9( 29)
10( 29)
10( 41)
10( 29)
10( 41)
10( 35)
10( 31)
10( 34)
10( 41)
9( 34) 9( 34) 9( 34)
9( 0)
9( 32)
9( 0)
9( 34)
9( 0)
9( 34)
9( 0) 9( 0) 9( 0)
9( 35) 9( 35) 9( 31) 10( 0) 10( 0) 10( 0) 10( 0)
10( 33) 10( 29) 10( 29) 10( 32)
9( 25)
9( 35)
9( 0)
9( 29)
9( 0)
9( 29)
9( 24) 9( 24) 9( 0)
10( 30)
10( 31)
10( 30)
10( 31)
10( 30)
10( 31)
10( 30)
10( 41)
9( 31) 9( 31) 9( 31)
9( 31)
9( 32)
9( 31)
9( 34)
9( 31)
9( 34)
9( 0) 9( 0) 9( 24)
9( 35) 9( 31) 9( 31) 10( 0) 10( 0)
10( 33) 10( 0) 10( 0) 10( 32)
9( 31)
9( 30)
9( 31)
9( 30)
12( 29) 12( 29)
10( 33)
10( 0)
10( 32)
10( 0)
9( 0) 9( 24) 9( 24) 9( 27)
16( 28)
10( 0)
16( 28)
10( 0)
9( 31) 9( 31) 9( 34)
9( 26) 9( 0)9( 31)
9( 24) 9( 24)
10( 31)
9( 24)
9( 31)
9( 24)
10( 31)
9( 24)
9( 35) 9( 31) 9( 31) 9( 31) 10( 0) 10( 0)
10( 35) 10( 0) 10( 0) 10( 34)
9( 31)
9( 24)
9( 31)
9( 24)
12( 31)
9( 24)
10( 33)
10( 0)
10( 32)
10( 0)
9( 24) 9( 24) 9( 24) 9( 27)
15( 28)
10( 0)
15( 28)
10( 0)
9( 0) 9( 0) 9( 31) 9( 27) 9( 31) 9( 31) 9( 34)
10( 31)
10( 31)
9( 24)
9( 35) 9( 34)
10( 31)
9( 24)
9( 31)
9( 24)
10( 0) 10( 0) 10( 0) 10( 0)
13( 31)
9( 24)
9( 31)
9( 24)
9( 31)
9( 24)
10( 35) 10( 28) 10( 28) 10( 34)
10( 28)
10( 0)
10( 28)
10( 0)
10( 28)
10( 0)
10( 28)
10( 0)
9( 0) 9( 0) 9( 0) 9( 24) 9( 24) 9( 24)
9( 31) 9( 31) 9( 31) 9( 31) 9( 31) 9( 31)
10( 0) 10( 0) 10( 0) 10( 0)
9( 31)
9( 24)
9( 31)
9( 24)
9( 31)
9( 24)
9( 31)
9( 24)
9( 31)
9( 24)
9( 31)
9( 24)
10( 28) 10( 28) 10( 28) 10( 28)
10( 32)
10( 0)
10( 32)
10( 0)
10( 33)
10( 0)
10( 33)
10( 0)
9( 0) 9( 0) 9( 0) 9( 25)
9( 30)
9( 30)
9( 43)
9( 42)
9( 30)
9( 25)
9( 0)
9( 0)
9( 0)
9( 30)
9( 0)
9( 0) 9( 0)
9( 35)
9( 30)
9( 0) 9( 25)
9( 0)
9( 0)
9( 30)
9( 30)
7( 35)
7( 29)
7( 34)
7( 30)
9( 0)
9( 0)
9( 0) 9( 25)
9( 30)
9( 30)
9( 0) 9( 25)
9( 35)
9( 30)
9( 0)
9( 0)
9( 0)
9( 0)
9( 25)
9( 30)
9( 43)
9( 43)
9( 42)
9( 43)
9( 42)
9( 43) 9( 0)
9( 0)
9( 42)
9( 43)
9( 0)
9( 0)
9( 43)
9( 0)
9( 43)
9( 0)
9( 42)
9( 43)
9( 42)
9( 0)
-7-
55. 2( 34) 55. 2( 34) - 20. 6( 27)
- 27. 7( 27)
39. 9( 34)
- 15. 6( 35) - 38. 6( 34) - 38. 6( 34) - 20. 2( 24) - 19. 4( 24) - 7. 1( 24)
12. 7( 26) 0. 0( 0) 52. 7( 31) 152. 1( 31) 152. 1( 31) 49. 5( 31)
63. 1( 34)
55. 5( 30)
- 27. 7( 27)
0. 0( 0) 61. 4( 34)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
120. 7( 30)
251. 7( 29)251. 8( 29)
251. 8( 29)
82. 5( 35)
0. 0( 0) - 44. 4( 41) - 48. 6( 31) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
67. 9( 29) 63. 7( 29) 30. 7( 30) 330. 8( 28) 317. 2( 28)155. 2( 28)36. 1( 33)
310. 2( 29)
251. 7( 29)
360. 8( 35)
0. 0( 0) 0. 0( 0)
61. 6( 35) 0. 0( 0)
-8-
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
67. 9( 29) 63. 7( 29) 30. 6( 30) 330. 8( 28) 317. 2( 28)156. 3( 28)36. 1( 32)
0. 0( 0)
0. 0( 0)
图 4-6
- 3. 0( 25) - 3. 0( 25)
99. 4( 30) 169. 1( 30) 169. 1( 30) 50. 1( 30)
- 4. 7( 24)
64. 9( 31)
29. 1( 31)
- 3. 0( 25)
37. 5( 30) 37. 5( 30) 29. 4( 30)
- 18. 2( 26)
- 1. 3( 25) - 2. 3( 25)
76. 0( 33)
74. 9( 33)
0. 0( 0)
0. 0( 0)
0) 6( 31)
0) - 6. 1( 24)
- 6. 1( 24)
64. 9( 31)
43. 0( 31)
0. 0( 182.
165. 2( 30)
0. 0( 0)
234. 2( 247.
31) 1( 31)
0. 0( 0)
0. 0( 0)
0. 0( 0)
31. 8( 35) 72. 6( 33)
60. 9( 35) 72. 6( 33)
0. 0( 0)
0. 0( 0)
181. 7( 31)
- 12. 6( 26) 0. 0( 0)
- 19. 1( 26) 0. 0( 0)
- 14. 0( 24)
- 31. 4( 29)- 22. 3( 30) - 2. 5( 24)
0. 0( 0) - 31. 4( 29)0. 0( 0) 224. 4( 31) - 8. 0( 24) 32. 1( 31)
104. 2( 31)
36. 2( 28) 33. 5( 32) - 12. 8( 24)249. 0( 31)
- 5. 7( 26)0. 0(
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
224. 4( 31) 54. 5( 30)151. 9( 30) 163. 6( 30) 40. 0( 42) 40. 4( 42)
31. 8( 35)
64. 3( 35)
43. 0( 31)
64. 3( 35)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 16. 5( 26) - 25. 9( 33)- 28. 6( 35)- 22. 3( 30)- 12. 8( 24) - 3. 7( 24) - 2. 5( 24)
26. 8( 35) 26. 8( 35) 21. 5( 25) 101. 2( 31)149. 6( 31) 149. 6( 31)43. 0( 31)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
54. 5( 30) 75. 1( 30) 0. 0( 0)
24. 8( 30)
15. 5( 43) 16. 0( 43)
21. 1( 35)
75. 1( 30)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 9. 9( 42) - 9. 9( 42)
- 1. 7( 42) 0. 0( 0) 0. 0( 0) 26. 4( 43) 26. 4( 43)
23. 8( 43) 40. 9( 35) 42. 4( 35)
4. 弯矩计算结果
FRAME 2
FOUNDATION CALCULATION REPORT
目 录
一. 结果简图 ................................................................................................................................................................. 2
1. 模型基本简图 ................................................................................................................................................... 2
2. 承载力计算结果 ............................................................................................................................................... 5
3. 弯矩计算结果 ................................................................................................................................................... 7
4. 配筋计算结果 ................................................................................................................................................... 8
一. 基础计算结果简图
1. 模型基本简图
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0 20000. 0
图 7-1 模型信息
MODEL
图 7-2 基础荷载
LOAD (KN)
-4-
44. 4( 10) 51. 3( 10) 57. 2( 10) 63. 9( 10) 71. 5( 10) 79. 8( 10) 88. 5( 10) 96. 2( 10) 102. 6( 10) 106. 7( 10) 107. 9( 10) 107. 5( 10) 105. 8( 10) 102. 3( 10) 96. 9( 10) 89. 8( 6) 79. 6( 6) 67. 9( 6) 57. 1( 6) 46. 3( 6) 35. 5( 6)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
43. 2( 10) 50. 5( 10) 57. 0( 10) 64. 2( 10) 72. 1( 10) 80. 6( 10) 89. 4( 10) 97. 3( 10) 104. 5( 10) 108. 9( 10) 109. 9( 10) 109. 5( 10) 108. 0( 10) 105. 2( 10) 99. 8( 10) 92. 0( 10) 81. 4( 6) 69. 7( 6) 58. 7( 6) 47. 7( 6) 36. 7( 6)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
41. 6( 10) 49. 3( 10) 56. 9( 10) 64. 7( 10) 73. 0( 10) 81. 8( 10) 90. 6( 10) 99. 1( 10) 106. 3( 10) 110. 5( 10) 111. 8( 10) 111. 7( 10) 110. 4( 10) 107. 6( 10) 101. 8( 10) 92. 9( 10) 82. 6( 10) 71. 6( 6) 60. 5( 6) 49. 2( 6) 38. 1( 8)
无震最大反力 No Seismic action maximum reaction force
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
41. 8( 12) 49. 3( 10) 57. 5( 10) 65. 8( 10) 74. 5( 10) 83. 5( 10) 92. 4( 10) 100. 7( 10) 107. 5( 10) 112. 0( 10) 114. 1( 10) 114. 3( 10) 113. 0( 10) 109. 7( 10) 103. 9( 10) 95. 4( 10) 85. 2( 10) 74. 1( 6) 62. 6( 6) 51. 0( 6) 39. 9( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
43. 0( 12) 50. 4( 12) 58. 9( 10) 67. 7( 10) 76. 8( 10) 86. 1( 10) 95. 2( 10) 103. 5( 10) 110. 2( 10) 114. 8( 10) 117. 2( 10) 117. 7( 10) 116. 5( 10) 113. 2( 10) 107. 3( 10) 98. 9( 10) 88. 5( 10) 77. 1( 6) 65. 3( 6) 53. 3( 6) 42. 1( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
45. 0( 12) 52. 8( 12) 61. 0( 10) 70. 3( 10) 79. 9( 10) 89. 6( 10) 99. 0( 10) 107. 6( 10) 114. 5( 10) 119. 1( 10) 121. 4( 10) 121. 9( 10) 121. 0( 10) 118. 0( 10) 112. 2( 10) 103. 4( 10) 92. 5( 10) 80. 6( 6) 68. 3( 6) 55. 9( 6) 44. 7( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
47. 6( 12) 55. 7( 12) 64. 0( 12) 73. 4( 10) 83. 4( 10) 93. 5( 10) 103. 4( 10) 112. 4( 10) 119. 9( 10) 124. 3( 10) 125. 9( 10) 126. 3( 10) 125. 7( 10) 123. 6( 10) 118. 0( 10) 108. 4( 10) 96. 9( 10) 84. 4( 6) 71. 5( 6) 58. 8( 8) 47. 4( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
50. 4( 12) 58. 5( 12) 67. 1( 12) 76. 6( 10) 87. 0( 10) 97. 4( 10) 107. 5( 10) 116. 8( 10) 124. 1( 10) 128. 2( 10) 129. 6( 10) 129. 9( 10) 129. 4( 10) 127. 6( 10) 122. 3( 10) 112. 8( 10) 101. 0( 6) 87. 8( 6) 74. 3( 6) 61. 7( 8) 50. 0( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
53. 3( 12) 61. 4( 12) 69. 3( 12) 78. 9( 10) 88. 9( 10) 99. 3( 10) 110. 0( 10)119. 0( 10) 125. 7( 10) 129. 8( 10) 131. 7( 10) 132. 3( 10) 131. 6( 10) 129. 1( 10) 124. 3( 10)117. 2( 6) 105. 2( 6) 90. 1( 6) 76. 3( 6) 63. 8( 8) 51. 9( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
54. 6( 12) 62. 5( 12) 70. 2( 12) 79. 7( 10) 89. 3( 10) 99. 5( 10) 110. 0( 10)118. 6( 10) 125. 2( 10) 129. 7( 10) 132. 5( 10) 133. 3( 10) 132. 1( 10) 129. 3( 10) 124. 3( 6) 117. 4( 6) 105. 6( 6) 90. 8( 6) 77. 4( 8) 65. 0( 8) 53. 1( 2)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
54. 2( 12) 61. 7( 12) 69. 8( 10) 79. 0( 10) 88. 6( 10) 98. 4( 10) 107. 9( 7) 116. 5( 7) 123. 2( 10) 128. 3( 10) 131. 7( 10) 132. 7( 10) 131. 2( 10) 127. 8( 10) 122. 5( 6) 114. 0( 6) 103. 0( 6) 90. 3( 6) 77. 6( 8) 65. 3( 8) 53. 5( 2)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
-5-
53. 0( 12) 60. 7( 7) 69. 5( 7) 78. 7( 7) 88. 1( 7) 97. 6( 7) 106. 7( 7) 114. 9( 7) 121. 7( 7) 126. 8( 7) 130. 0( 10) 131. 1( 10) 129. 4( 10) 126. 1( 6) 120. 3( 6) 112. 0( 6) 101. 4( 6) 89. 3( 6) 77. 4( 8) 65. 2( 8) 53. 4( 2)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
52. 8( 9) 61. 2( 9) 70. 2( 7) 79. 3( 7) 88. 6( 7) 97. 7( 7) 106. 5( 7) 114. 3( 7) 121. 0( 7) 126. 2( 7) 129. 5( 7) 129. 8( 6) 128. 5( 6) 124. 9( 6) 119. 0( 6) 110. 8( 6) 100. 5( 6) 89. 1( 8) 77. 3( 8) 65. 2( 8) 53. 5( 2)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
53. 8( 9) 62. 4( 9) 71. 6( 7) 80. 9( 7) 90. 1( 7) 99. 1( 7) 107. 5( 7) 115. 0( 7) 121. 2( 7) 126. 0( 7) 129. 4( 11) 130. 2( 11) 127. 9( 6) 124. 5( 6) 118. 8( 6) 110. 8( 6) 100. 7( 6) 89. 6( 8) 77. 9( 8) 65. 7( 8) 53. 8( 2)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
56. 4( 13) 65. 2( 13) 74. 4( 11) 83. 8( 11) 93. 0( 11) 101. 8( 11) 109. 9( 7) 116. 9( 11) 122. 6( 11) 127. 0( 11) 129. 9( 11) 130. 3( 11) 128. 2( 11) 124. 6( 6) 119. 7( 6) 111. 9( 6) 101. 9( 6) 90. 8( 8) 78. 9( 8) 66. 6( 8) 54. 4( 2)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
62. 6( 13) 71. 6( 13) 80. 6( 13) 89. 8( 13) 99. 0( 11) 107. 6( 11) 115. 2( 11) 121. 6( 11) 125. 9( 11) 128. 6( 11) 130. 2( 11) 130. 0( 11) 128. 2( 11) 125. 3( 11) 120. 4( 6) 113. 6( 6) 103. 8( 8) 92. 5( 8) 80. 3( 8) 67. 9( 8) 55. 5( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0]
70. 2( 13) 79. 0( 13) 88. 0( 13) 97. 2( 13) 105. 3( 13) 112. 8( 13) 120. 3( 11)125. 7( 11) 128. 7( 11) 129. 8( 11) 129. 9( 11) 129. 1( 11) 127. 6( 11) 125. 1( 11) 121. 3( 11)115. 9( 11) 106. 3( 8) 93. 7( 8) 81. 4( 8) 68. 9( 8) 56. 6( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
78. 9( 13) 87. 4( 13) 95. 8( 13) 104. 3( 13)111. 6( 13) 118. 4( 13) 124. 9( 13)128. 5( 13) 130. 2( 11) 130. 4( 11) 129. 6( 11) 128. 4( 11) 126. 7( 11) 124. 5( 11) 121. 0( 11)116. 0( 13) 106. 3( 13) 94. 1( 8) 82. 1( 8) 69. 8( 8) 57. 4( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
图 7-3
88. 8( 13) 96. 6( 13) 103. 8( 13) 111. 1( 13) 118. 0( 13) 124. 0( 13) 128. 6( 13) 131. 4( 13) 132. 2( 13) 131. 4( 13) 129. 9( 13) 128. 3( 13) 126. 5( 13) 124. 3( 13) 120. 7( 13) 114. 7( 13) 105. 8( 13) 94. 6( 13) 82. 5( 8) 70. 4( 8) 58. 1( 8)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
pk, avg=90. 7( 1)
[ 1*0]
pk, max=75. 0( 1)
[ 1. 2*0]
2. 承载力计算结果
41. 7( 20) 46. 6( 20) 50. 7( 20) 55. 4( 20) 60. 6( 20) 66. 4( 20) 72. 6( 20) 78. 0( 20) 82. 4( 20) 85. 2( 20) 85. 9( 20) 85. 6( 20) 84. 4( 20) 82. 1( 20) 78. 5( 20) 73. 5( 20) 66. 2( 20) 58. 0( 18) 50. 7( 18) 43. 4( 18) 35. 9( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
41. 5( 20) 46. 9( 20) 51. 6( 20) 56. 8( 20) 62. 5( 20) 68. 6( 20) 74. 8( 20) 80. 5( 20) 85. 5( 20) 88. 5( 20) 89. 2( 20) 88. 9( 20) 88. 0( 20) 86. 0( 20) 82. 2( 20) 76. 7( 20) 69. 1( 20) 60. 7( 18) 53. 1( 18) 45. 4( 18) 37. 6( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
41. 2( 20) 47. 0( 20) 52. 7( 20) 58. 5( 20) 64. 6( 20) 71. 0( 20) 77. 5( 20) 83. 5( 20) 88. 7( 20) 91. 7( 20) 92. 6( 20) 92. 5( 20) 91. 6( 20) 89. 7( 20) 85. 5( 20) 79. 0( 20) 71. 4( 20) 63. 6( 18) 55. 6( 18) 47. 5( 18) 39. 3( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
有震最大反力 Seismic action maximum reaction force
41. 8( 20) 48. 1( 20) 54. 4( 20) 60. 8( 20) 67. 3( 20) 74. 0( 20) 80. 6( 20) 86. 7( 20) 91. 6( 20) 94. 8( 20) 96. 4( 20) 96. 6( 20) 95. 7( 20) 93. 3( 20) 89. 0( 20) 82. 7( 20) 75. 0( 20) 67. 0( 18) 58. 6( 18) 50. 0( 18) 41. 3( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
43. 3( 20) 50. 0( 20) 56. 8( 20) 63. 7( 20) 70. 8( 20) 77. 9( 20) 84. 7( 20) 90. 9( 20) 95. 8( 20) 99. 2( 20) 100. 9( 20) 101. 3( 20) 100. 5( 20) 98. 1( 20) 93. 7( 20) 87. 2( 20) 79. 3( 18) 71. 0( 18) 62. 1( 18) 52. 9( 18) 43. 6( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
45. 5( 20) 52. 6( 20) 59. 9( 20) 67. 3( 20) 74. 9( 20) 82. 5( 20) 89. 7( 20) 96. 2( 20) 101. 3( 20) 104. 7( 20) 106. 4( 20) 106. 8( 20) 106. 2( 20) 104. 0( 20) 99. 6( 20) 92. 7( 20) 84. 6( 18) 75. 6( 18) 66. 0( 18) 56. 2( 18) 46. 4( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
48. 2( 20) 55. 6( 20) 63. 2( 20) 71. 2( 20) 79. 4( 20) 87. 4( 20) 95. 1( 20) 101. 9( 20) 107. 5( 20) 110. 8( 20) 112. 0( 20) 112. 4( 20) 112. 1( 20) 110. 6( 20) 106. 2( 20) 98. 8( 18) 90. 4( 18) 80. 5( 18) 70. 1( 18) 59. 7( 18) 49. 3( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
50. 9( 20) 58. 5( 20) 66. 4( 20) 74. 9( 20) 83. 6( 20) 92. 1( 20) 100. 1( 20) 107. 3( 20) 112. 8( 20) 115. 8( 20) 116. 9( 20) 117. 3( 20) 117. 0( 20) 115. 7( 20) 111. 6( 20) 105. 0( 18) 95. 9( 18) 85. 2( 18) 73. 9( 18) 62. 9( 18) 52. 1( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
53. 6( 20) 61. 2( 20) 68. 6( 20) 77. 4( 20) 86. 0( 20) 94. 6( 20) 103. 2( 20)110. 4( 20) 115. 6( 20) 118. 7( 20) 120. 3( 20) 120. 9( 20) 120. 5( 20) 118. 7( 20) 115. 4( 18)110. 9( 18) 101. 3( 18) 88. 6( 18) 76. 8( 18) 65. 4( 18) 54. 2( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
54. 8( 20) 62. 1( 20) 69. 3( 20) 77. 8( 20) 86. 2( 20) 94. 7( 20) 103. 4( 20)110. 5( 20) 115. 9( 20) 119. 7( 20) 122. 1( 20) 123. 0( 20) 122. 1( 20) 120. 0( 20) 117. 5( 18)112. 7( 18) 103. 0( 18) 90. 4( 18) 78. 5( 18) 66. 8( 18) 55. 4( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
54. 2( 20) 61. 2( 20) 68. 6( 19) 76. 9( 19) 85. 7( 19) 94. 6( 19) 103. 0( 19) 110. 2( 19) 115. 4( 19) 118. 7( 20) 122. 0( 20) 123. 0( 20) 121. 9( 20) 120. 2( 18) 117. 2( 18) 110. 8( 18) 101. 6( 18) 90. 7( 18) 79. 1( 18) 67. 4( 18) 55. 8( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
-6-
53. 6( 19) 61. 5( 19) 69. 4( 19) 77. 6( 19) 86. 1( 19) 94. 6( 19) 102. 6( 19) 109. 6( 19) 115. 1( 19) 118. 8( 19) 120. 4( 20) 121. 6( 20) 120. 9( 18) 119. 8( 18) 116. 2( 18) 109. 8( 18) 101. 0( 18) 90. 5( 18) 79. 2( 18) 67. 6( 18) 55. 9( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
54. 0( 19) 62. 1( 19) 70. 3( 19) 78. 6( 19) 87. 0( 19) 95. 2( 19) 103. 0( 19) 109. 8( 19) 115. 3( 19) 119. 2( 19) 121. 2( 19) 120. 3( 18) 121. 1( 18) 119. 7( 18) 115. 8( 18) 109. 5( 18) 100. 9( 18) 90. 7( 18) 79. 5( 18) 67. 9( 18) 56. 1( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
55. 0( 19) 63. 4( 19) 71. 8( 19) 80. 3( 19) 88. 7( 19) 96. 9( 19) 104. 5( 19) 110. 9( 19) 116. 1( 19) 119. 6( 19) 121. 8( 21) 122. 9( 21) 121. 2( 18) 120. 1( 18) 116. 5( 18) 110. 3( 18) 101. 8( 18) 91. 6( 18) 80. 4( 18) 68. 7( 18) 56. 8( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
57. 1( 19) 65. 7( 19) 74. 3( 19) 83. 0( 19) 91. 6( 19) 99. 8( 19) 107. 1( 19) 113. 2( 19) 117. 5( 19) 121. 3( 21) 124. 2( 21) 124. 8( 21) 123. 0( 21) 120. 8( 18) 118. 0( 18) 112. 1( 18) 103. 7( 18) 93. 3( 18) 81. 8( 18) 70. 0( 18) 58. 0( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
63. 5( 21) 72. 0( 21) 80. 7( 21) 89. 5( 21) 98. 1( 21) 105. 8( 21) 112. 5( 21) 118. 2( 21) 122. 1( 21) 124. 6( 21) 126. 2( 21) 126. 2( 21) 124. 6( 21) 122. 0( 21) 119. 4( 18) 114. 5( 18) 106. 2( 18) 95. 3( 18) 83. 5( 18) 71. 5( 18) 59. 5( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0]
71. 4( 21) 79. 9( 21) 88. 5( 21) 97. 4( 21) 105. 1( 21) 112. 4( 21) 119. 4( 21)123. 9( 21) 126. 4( 21) 127. 4( 21) 127. 5( 21) 126. 9( 21) 125. 5( 21) 123. 3( 21) 119. 9( 21)117. 1( 18) 109. 0( 18) 97. 0( 18) 85. 1( 18) 72. 9( 18) 60. 8( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
80. 6( 21) 88. 7( 21) 96. 8( 21) 105. 0( 21)111. 9( 21) 118. 5( 21) 124. 7( 21)128. 1( 21) 129. 5( 21) 129. 6( 21) 128. 7( 21) 127. 5( 21) 126. 0( 21) 123. 9( 21) 120. 8( 21)116. 6( 18) 109. 1( 18) 97. 7( 18) 86. 1( 18) 74. 0( 18) 62. 0( 18)
图 7-4
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2*0]
90. 8( 21) 98. 3( 21) 105. 2( 21) 112. 2( 21) 118. 9( 21) 124. 6( 21) 129. 0( 21) 131. 6( 21) 132. 2( 21) 131. 4( 21) 129. 9( 21) 128. 3( 21) 126. 6( 21) 124. 4( 21) 121. 0( 21) 115. 2( 21) 107. 5( 18) 98. 0( 18) 86. 8( 18) 74. 9( 18) 62. 9( 18)
[ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2* 0] [ 1. 2* 0] [ 1. 2*0] [ 1. 2*0] [ 1. 2* 0]
pk, avg=81. 4( 14)
[ 1* 0]
pk, max=63. 0( 14)
[ 1. 2*0]
3. 弯矩计算结果
- 196. 9( 31)- 204. 6( 35)- 237. 9( 35)- 255. 8( 35)- 255. 8( 35)- 249. 4( 35)- 207. 4( 35)- 148. 1( 35) 0. 0( 0) - 46. 8( 35)- 118. 2( 43)- 150. 3( 35)- 179. 3( 35)- 192. 3( 33)- 192. 3( 33)- 184. 0( 33)- 154. 4( 32)- 112. 7( 32) 0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 97. 1( 26) 334. 0( 26) 334. 0( 26) 256. 9( 34) 239. 5( 34) 140. 5( 42) 44. 3( 26) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 62. 4( 43) 85. 2( 29)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 150. 3( 35)- 170. 5( 35)- 182. 0( 33)- 182. 0( 33)- 177. 8( 33)- 154. 5( 32)- 112. 7( 32) 0. 0( 0)
- 196. 9( 31)- 196. 9( 31)- 210. 8( 29)- 229. 9( 33)- 234. 8( 35)- 234. 8( 35)- 209. 9( 35)- 148. 1( 35) 0. 0( 0) - 46. 8( 35) - 118. 2( 43)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 65. 6( 26) 334. 0( 26) 334. 0( 26) 256. 9( 34) 254. 0( 34)173. 5( 42) 71. 3( 26) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 62. 4( 43) 81. 4( 29)
0. 0( 0)
51. 7( 26) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
27. 6( 33) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
14. 9( 42) 0. 0( 0)
58. 0( 33) 0. 0( 0)
0. 0( 0)
0. 0( 0)
54. 4( 33) 0. 0( 0)
- 73. 5( 26) - 153. 1( 26)- 174. 1( 34)- 197. 4( 29)- 221. 1( 33)- 221. 1( 33)- 217. 4( 35)- 177. 4( 35)- 122. 7( 35)- 90. 4( 43) - 107. 8( 43)- 140. 3( 35)- 161. 3( 35)- 173. 7( 33)- 173. 7( 33)- 173. 2( 29)- 154. 5( 32)- 100. 7( 32)- 42. 0( 32)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 65. 6( 26) 167. 2( 26) 244. 6( 26) 290. 1( 34) 290. 1( 34) 232. 0( 34) 101. 8( 26) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 18. 1( 43)
0. 0( 0)
0. 0( 0)
127. 4( 29) 110. 5( 29)0. 0( 0)
127. 4( 29) 110. 5( 29)0. 0( 0)
- 61. 7( 26) - 118. 8( 26)- 145. 9( 26)- 162. 2( 32)- 222. 2( 33)- 234. 2( 33)- 234. 2( 33)- 204. 0( 35)- 148. 3( 35)- 117. 0( 43)- 117. 0( 43)- 125. 3( 43)- 148. 5( 35)- 165. 1( 33)- 169. 1( 29)- 169. 1( 29)- 149. 6( 32)- 107. 9( 32)- 51. 6( 32)
40. 1( 35) 246. 4( 35) 246. 4( 35) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 139. 2( 26) 264. 0( 26) 479. 5( 34) 479. 5( 34) 331. 7( 34) 115. 6( 42) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
40. 1( 35) 484. 0( 35) 460. 6( 35)180. 1( 35) 0. 0( 0) 0. 0( 0) 0. 0( 0) 116. 1( 26) 264. 0( 26) 688. 1( 34) 683. 9( 34)363. 3( 34) 133. 4( 42) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 11. 3( 26) - 103. 7( 26)- 103. 7( 26)- 116. 4( 32)- 220. 9( 33)- 255. 2( 33)- 255. 2( 33)- 226. 8( 35)- 154. 6( 35) - 114. 8( 43)- 114. 8( 43)- 81. 1( 43) - 116. 8( 35)- 150. 0( 33)- 166. 0( 29)- 166. 0( 29)- 147. 8( 32)- 104. 0( 32)- 48. 7( 32)
- 17. 0( 26) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 207. 6( 33)- 255. 2( 33)- 255. 2( 33)- 226. 8( 35)- 151. 4( 35) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 102. 0( 35)- 147. 3( 35)- 168. 9( 29)- 168. 9( 29)- 138. 8( 32)- 82. 9( 34) - 29. 7( 34)
- 219. 1( 26)
143. 7( 35) 478. 4( 29) 478. 4( 29) 287. 1( 31) 0. 0( 0) 0. 0( 0) 0. 0( 0) 139. 0( 26) 351. 9( 34) 717. 1( 34) 717. 1( 34) 548. 4( 34) 239. 5( 34) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 53. 7( 33)
- 124. 0( 28)- 155. 9( 33)- 155. 9( 33)- 130. 4( 33)0. 0( 0)
- 124. 0( 28)- 171. 7( 28)- 171. 7( 28)- 141. 8( 33)0. 0( 0)
图 7-5
0. 0( 0) 0. 0( 0) 0. 0( 0) - 59. 8( 26) 0. 0( 0)
- 22. 6( 42) 0. 0( 0)
- 75. 2( 24) - 150. 8( 26)- 202. 2( 26)- 228. 9( 26)538. 4( 35) - 101. 4( 24)
- 226. 3( 26) - 219. 1( 26)- 101. 4( 24)
115. 4( 35) 724. 0( 29) 308. 3( 31) 0. 0( 0) 47. 0( 26) 86. 0( 26) 157. 5( 26) 343. 4( 42) 555. 6( 34) 302. 2( 32) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 174. 0( 26)- 208. 3( 26)- 208. 3( 26)- 170. 6( 26)- 56. 5( 24) 0. 0( 0)
- 50. 1( 27) - 90. 3( 26) - 138. 8( 26)- 183. 6( 26)- 183. 6( 26)- 180. 9( 26)- 81. 8( 24) 0. 0( 0)
- 135. 7( 27)- 185. 3( 27)- 185. 3( 27)- 163. 7( 27)- 82. 5( 24) 0. 0( 0)
0. 0( 0)
0. 0( 0)
- 37. 5( 33) - 81. 9( 33) - 116. 9( 35)- 128. 4( 35)- 128. 4( 35)- 95. 6( 35) - 27. 6( 24) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0) 0. 0( 0) - 181. 4( 33)- 206. 3( 29)- 206. 3( 29) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 46. 2( 27) - 90. 3( 26) - 133. 5( 26)- 157. 6( 26)- 157. 6( 26)- 138. 7( 26)- 108. 5( 24)- 68. 0( 24) 0. 0( 0)
- 39. 6( 24) - 83. 3( 24) - 118. 2( 26)- 140. 7( 24)- 140. 7( 24)- 140. 6( 24)- 119. 7( 24)- 79. 7( 24) 0. 0( 0)
- 28. 5( 24) - 73. 1( 24) - 119. 6( 24)- 141. 9( 24)- 141. 9( 24)- 140. 6( 24)- 119. 7( 24)- 79. 7( 24) 0. 0( 0)
- 133. 1( 27)- 158. 3( 27)- 158. 3( 27)- 137. 6( 24)- 110. 5( 24)- 64. 0( 24) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 89. 5( 33) - 89. 5( 33) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 181. 4( 33)- 206. 3( 29)- 206. 3( 29) 0. 0( 0) 0. 0( 0) - 32. 2( 26)
85. 3( 31) 192. 3( 31) 231. 3( 31) 231. 3( 31) 292. 5( 26) 292. 5( 26) 278. 0( 26) 267. 3( 26) 343. 5( 26) 432. 9( 34) 432. 9( 34) 940. 6( 32) 940. 6( 32) 158. 1( 32) 0. 0( 0) 0. 0( 0) 686. 5( 33) 686. 5( 33) 97. 1( 33)
0. 0( 0)
935. 8( 31) 0. 0( 0)
908. 7( 29) 935. 8( 31) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 23. 2( 28) - 22. 0( 40) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 70. 4( 33) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 132. 7( 35)- 153. 1( 33)- 153. 1( 33)- 77. 0( 25) - 39. 2( 26) 0. 0( 0)
24. 4( 41) 72. 8( 41) 154. 9( 25) 487. 0( 26) 487. 0( 26) 818. 0( 26) 818. 0( 26) 267. 3( 26) 626. 4( 26) 626. 4( 26) 414. 4( 32) 414. 4( 32) 351. 8( 32) 158. 1( 32) 0. 0( 0) 0. 0( 0) 108. 7( 33) 108. 7( 33) 97. 1( 33)
-7-
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 23. 2( 28) - 23. 2( 28) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 45. 3( 27) - 100. 9( 27)- 110. 5( 27)- 110. 5( 27)- 78. 2( 24) - 39. 2( 26) - 12. 5( 26)
0. 0( 0) 36. 6( 24) 159. 4( 26) 487. 0( 26) 487. 0( 26) 818. 0( 26) 818. 0( 26) 300. 1( 26) 626. 4( 26) 626. 4( 26) 383. 4( 34) 334. 9( 34) 272. 3( 32) 131. 1( 32) 0. 0( 0) 0. 0( 0) 0. 0( 0) 30. 5( 33) 30. 5( 33)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
- 20. 4( 29) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 109. 9( 27)- 134. 7( 35)- 134. 7( 35)- 78. 2( 24) - 39. 1( 26) - 12. 5( 26)
29. 7( 40) 92. 2( 24) 210. 7( 24) 261. 0( 26) 346. 5( 26) 346. 5( 26) 313. 5( 26) 312. 0( 26) 392. 2( 26) 403. 9( 34) 454. 6( 32) 454. 6( 32) 407. 1( 32) 214. 5( 32) 0. 0( 0) 0. 0( 0) 111. 5( 29) 111. 5( 29) 94. 1( 29)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 105. 9( 33)- 102. 8( 33) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 137. 5( 35)- 173. 8( 28)- 173. 8( 28) 0. 0( 0) 0. 0( 0) - 46. 9( 40)
94. 9( 40) 205. 1( 40) 215. 8( 40) 520. 0( 24) 520. 0( 24) 258. 8( 26) 200. 4( 26) 312. 0( 26) 709. 6( 26) 709. 6( 26) 454. 6( 32) 1154. 1( 32)1154. 1( 32)214. 5( 32) 0. 0( 0)
0. 0( 0) 0. 0( 0) 705. 3( 29) 705. 3( 29) 94. 1( 29)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 151. 4( 33)- 151. 4( 33)- 139. 5( 33) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 137. 5( 35)- 173. 8( 28)- 173. 8( 28) 0. 0( 0) 0. 0( 0) - 41. 0( 24)
94. 9( 40) 547. 5( 30) 547. 5( 30) 520. 0( 24) 520. 0( 24) 110. 2( 26) 111. 7( 26) 205. 3( 26) 709. 6( 26) 733. 6( 34) 733. 6( 34) 1154. 1( 32)1154. 1( 32)180. 9( 32) 0. 0( 0) 0. 0( 0) 705. 3( 29) 705. 3( 29) 120. 7( 29)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 55. 8( 24) 0. 0( 0)
弯矩图 Bending moment diagram 0. 0( 0) 783. 8( 30) 0. 0( 0) 0. 0( 0) - 112. 0( 35)- 148. 7( 28)- 148. 7( 28)- 90. 3( 24) 120. 7( 29) 120. 7( 29)
318. 9( 41) 313. 6( 26) 314. 0( 26) 325. 7( 24) 465. 1( 30) 795. 4( 30)
0. 0( 0) - 155. 2( 33)- 155. 2( 33)- 139. 5( 33) 0. 0( 0) 952. 6( 34) 950. 0( 34) 0. 0( 0)
176. 5( 32)400. 8( 32) 1056. 2( 29) 1056. 2( 29)408. 6( 33) 240. 6( 33) 420. 6( 33) 1082. 4( 28)1082. 4( 28)
88. 4( 40) 793. 2( 30) 428. 1( 30) 174. 7( 26) 110. 2( 26) 62. 8( 26) 205. 3( 26) 418. 2( 26) 615. 9( 34) 388. 7( 32) 180. 9( 32) 0. 0( 0) 0. 0( 0) 114. 2( 29)
0. 0( 0)
0. 0( 0) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 55. 8( 24) 0. 0( 0)
0. 0( 0) 0. 0( 0) - 80. 2( 27) - 109. 9( 24)- 109. 9( 24)- 90. 3( 24) 100. 4( 29) 98. 5( 29)
340. 3( 41) 211. 5( 26) 234. 0( 26) 257. 5( 24) 433. 6( 40) 795. 4( 30)1115. 8( 30)
793. 2( 30) 783. 8( 30) 0. 0( 0) - 100. 5( 33)- 155. 2( 33)- 155. 2( 33)- 137. 2( 33) 0. 0( 0) 952. 6( 34) 950. 0( 34) 0. 0( 0)
121. 6( 30) 408. 3( 30) 79. 0( 26) 37. 6( 26) 47. 7( 26) 143. 3( 26) 297. 8( 26) 464. 3( 34) 230. 2( 32) 82. 3( 32) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 1115. 8( 30) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 97. 9( 33) - 143. 9( 33)- 143. 9( 33)- 123. 3( 33) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 70. 3( 27) - 94. 3( 30) - 94. 3( 30) - 85. 0( 24) - 53. 3( 30) - 22. 5( 30)
121. 6( 30) 222. 7( 30) 247. 1( 30) 247. 1( 30) 72. 9( 24) 13. 9( 26) 40. 7( 26) 131. 0( 26) 297. 8( 26) 387. 9( 34) 401. 3( 34) 401. 3( 34) 204. 5( 34) 58. 0( 34) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
1112. 1( 30) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 83. 5( 33) - 123. 0( 33)- 123. 0( 33)- 105. 5( 35)- 48. 6( 35) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 63. 0( 27) - 83. 3( 30) - 83. 3( 30) - 79. 2( 30) - 53. 3( 30) - 22. 5( 30)
67. 9( 30) 120. 4( 30) 120. 4( 30) 102. 0( 40) 41. 4( 26) 6. 0( 26) 37. 8( 26) 118. 0( 26) 211. 3( 26) 274. 9( 34) 274. 9( 34) 256. 2( 34) 162. 5( 34) 49. 7( 34) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0) 0. 0( 0)
0. 0( 0)
98. 1( 42) 368. 9( 34) 408. 3( 34) 467. 1( 31)1156. 3( 29)1156. 3( 29) 593. 8( 29) 426. 1( 29) 377. 9( 33) 540. 6( 28) 713. 8( 28) 852. 1( 28)1070. 0( 30) 1056. 3( 30) 228. 3( 30) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0) 0. 0( 0) 0. 0( 0) - 40. 4( 43) - 82. 9( 35) - 106. 9( 33)- 106. 9( 33)- 95. 5( 35) - 50. 5( 35) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 33. 9( 35) - 61. 2( 35) - 75. 2( 30) - 75. 2( 30) - 74. 4( 28) - 47. 2( 28) 0. 0( 0)
38. 7( 30) 96. 9( 34) 94. 7( 26) 56. 5( 26) 21. 1( 26) 0. 0( 0) 30. 9( 26) 90. 4( 26) 168. 6( 26) 254. 2( 26) 253. 4( 26) 201. 5( 34) 118. 5( 34) 36. 6( 34) 0. 0( 0) 0. 0( 0) 0. 0( 0) 45. 9( 24) 49. 3( 24)
- 26. 8( 25) 0. 0( 0)
0. 0( 0)
98. 1( 42) 198. 9( 34) 198. 9( 34) 452. 7( 31) 752. 0( 29) 1158. 1( 29)1158. 1( 29)426. 1( 29) 299. 9( 33) 540. 6( 28) 1426. 8( 28)1426. 8( 28)852. 1( 28) 621. 0( 30) 228. 3( 30) 58. 1( 40) 0. 0( 0)
28. 6( 26) 84. 6( 42) 159. 7( 34) 287. 8( 31) 447. 2( 29) 1158. 1( 29)1158. 1( 29)432. 6( 29) 283. 7( 33) 521. 8( 28) 1426. 8( 28)1426. 8( 28)569. 3( 28) 383. 0( 30) 207. 1( 30) 58. 1( 40) 0. 0( 0)
- 20. 1( 28) 0. 0( 0)
- 20. 1( 28) 0. 0( 0)
- 26. 8( 25) 0. 0( 0)
1112. 1( 30) 282. 2( 30) 106. 6( 40) 42. 5( 34)
0. 0( 0) 0. 0( 0) 0. 0( 0) - 46. 1( 35) - 86. 5( 35) - 102. 4( 35)- 102. 4( 35)- 91. 0( 35) - 50. 5( 35) 0. 0( 0) 0. 0( 0) 0. 0( 0) - 37. 8( 35) - 62. 8( 35) - 72. 1( 33) - 72. 1( 33) - 69. 8( 28) - 47. 2( 28) 0. 0( 0)
36. 4( 34) 96. 9( 34) 94. 7( 26) 59. 5( 26) 0. 0( 0) 0. 0( 0) 21. 4( 26) 70. 9( 26) 139. 0( 26) 254. 2( 26) 253. 4( 26) 173. 6( 26) 90. 0( 34) 24. 9( 26) 0. 0( 0) 0. 0( 0) 0. 0( 0) 45. 9( 24) 49. 3( 24)
0. 0( 0)
- 50. 5( 34) - 50. 5( 34) 0. 0( 0)
63. 6( 35) 123. 9( 35) 192. 2( 29) 295. 9( 31) 336. 2( 31) 336. 2( 31) 474. 5( 31) 696. 5( 26) 696. 5( 26) 503. 1( 26) 766. 1( 30) 766. 1( 30) 481. 3( 30) 431. 2( 30) 275. 5( 30) 104. 6( 40) 27. 7( 40) 0. 0( 0)
128. 6( 31) 241. 5( 31) 316. 0( 31) 357. 8( 31) 478. 3( 31) 542. 0( 29) 542. 0( 29) 515. 2( 28) 512. 3( 30) 512. 3( 30) 500. 5( 30) 361. 4( 30) 213. 1( 30) 87. 5( 40) 23. 1( 40) 0. 0( 0)
0. 0( 0)
36. 2( 42) 102. 1( 34) 220. 8( 29) 447. 2( 29) 513. 9( 29) 513. 9( 29) 432. 6( 29) 324. 1( 33) 521. 8( 28) 637. 3( 28) 637. 3( 28) 569. 3( 28) 306. 3( 28) 162. 6( 30) 57. 6( 30) 11. 1( 24) 0. 0( 0)
- 9. 8( 29) 0. 0( 0)
0. 0( 0)
0. 0( 0)
0. 0( 0)
172. 0( 35) 339. 5( 35) 339. 5( 35) 462. 0( 31) 644. 6( 31) 644. 6( 31) 324. 6( 31) 696. 5( 26) 696. 5( 26) 325. 7( 24) 766. 1( 30) 766. 1( 30) 782. 7( 30) 782. 7( 30) 282. 2( 30) 104. 6( 40) 21. 4( 40) 9. 2( 42)
48. 8( 41) 121. 5( 31) 188. 3( 31) 234. 1( 31) 280. 4( 31) 474. 5( 31) 1051. 7( 31)1051. 7( 31)503. 1( 26) 442. 9( 30) 442. 9( 30) 435. 8( 30) 322. 3( 30) 211. 2( 40) 101. 7( 40) 28. 1( 40) 1. 6( 28)
90. 7( 41) 164. 5( 31) 230. 9( 31) 307. 0( 31) 478. 3( 31) 1051. 7( 31)1051. 7( 31)515. 2( 28) 420. 3( 30) 416. 1( 30) 387. 1( 30) 302. 6( 30) 188. 6( 30) 92. 4( 40) 28. 1( 40) 1. 6( 28)
60. 6( 42) 112. 0( 34) 176. 1( 34) 408. 9( 31) 476. 3( 29) 476. 3( 29) 445. 0( 29) 695. 0( 29) 695. 0( 29) 464. 8( 30) 857. 2( 30) 857. 2( 30) 623. 7( 30) 485. 2( 30) 245. 9( 30) 83. 0( 30) 11. 3( 40) 9. 3( 35)
64. 3( 34) 195. 2( 29) 330. 4( 29) 391. 7( 29) 391. 7( 29) 359. 2( 29) 324. 1( 33) 419. 2( 28) 477. 1( 28) 477. 1( 28) 421. 9( 28) 281. 0( 28) 137. 1( 30) 50. 4( 30) 11. 8( 24) 1. 7( 24)
167. 5( 29) 373. 9( 29) 464. 8( 29) 464. 8( 29) 407. 3( 29) 312. 5( 33) 431. 3( 28) 497. 7( 28) 497. 7( 28) 417. 6( 28) 243. 4( 28) 114. 1( 28) 39. 1( 30) 11. 8( 24) 5. 0( 24)
173. 0( 35) 245. 4( 35) 311. 7( 33) 478. 4( 31) 478. 4( 31) 463. 1( 31) 340. 3( 41) 183. 7( 41) 186. 5( 26) 237. 5( 24) 433. 6( 40) 664. 6( 30) 664. 6( 30) 594. 4( 30) 386. 4( 30) 196. 4( 30) 66. 0( 30) 19. 9( 34)
- 7. 0( 27)
11. 5( 27)
- 9. 8( 29) - 9. 4( 29)
135. 2( 32) 373. 9( 29) 1056. 2( 29)1056. 2( 29)407. 3( 29) 258. 6( 33) 431. 3( 28) 1082. 4( 28)1082. 4( 28)417. 6( 28) 195. 9( 28) 84. 7( 28) 28. 8( 24) 13. 7( 26) 13. 6( 24)
460. 6( 29) 296. 2( 29) 66. 1( 28) 17. 1( 24) 61. 7( 24) 60. 8( 24)
255. 7( 32)463. 4( 32) 488. 9( 32) 488. 9( 32) 408. 6( 33) 275. 2( 33) 420. 6( 33) 490. 1( 33) 490. 1( 33)460. 6( 29) 296. 2( 29) 73. 7( 32) 28. 0( 26) 61. 7( 24) 60. 8( 24)
42. 5( 34)
- 28. 0( 25) - 28. 0( 25) - 18. 2( 25)
- 28. 6( 25) - 28. 6( 25) - 18. 4( 25)
- 29. 7( 25) - 29. 7( 25) - 18. 9( 25)
- 31. 8( 25) - 31. 8( 25) - 18. 9( 25)
- 31. 8( 25) - 31. 8( 25) - 18. 3( 25)
- 32. 3( 41) - 31. 1( 31) - 20. 6( 32)
- 27. 8( 31) - 27. 8( 31) - 20. 6( 32)
- 20. 1( 31) - 20. 1( 31) - 16. 6( 29)
- 13. 4( 31) - 13. 4( 31) - 12. 4( 29)
15( 31) 15( 35) 15( 35) 15( 35) 15( 35) 15( 35) 15( 35) 15( 35) 15( 0) 15( 35) 15( 43) 15( 35) 15( 35) 15( 33) 15( 33) 15( 33) 15( 32) 15( 32) 15( 0)
15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 15( 42) 15( 26) 15( 0) 15( 0) 15( 0) 15( 0) 15( 43) 15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 34)
15( 26)
15( 27)
15( 27)
15( 27)
15( 24)
15( 33)
15( 24)
15( 33)
15( 33)
15( 32)
15( 33)
15( 33)
15( 33)
15( 33)
15( 42)
15( 28)
15( 33)
15( 42)
15( 29)
15( 29)
15( 33)
15( 42)
15( 31) 15( 31) 15( 29) 15( 33) 15( 35) 15( 35) 15( 35) 15( 35) 15( 0) 15( 35) 15( 43) 15( 35) 15( 35) 15( 33) 15( 33) 15( 33) 15( 32) 15( 32) 15( 0)
15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 15( 42) 15( 26) 15( 0) 15( 0) 15( 0) 15( 0) 15( 43) 15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 34)
15( 24)
15( 24)
15( 26)
15( 26)
15( 24)
15( 24)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 28)
15( 29)
15( 29)
15( 29)
15( 33)
15( 26) 15( 26) 15( 34) 15( 29) 15( 33) 15( 33) 15( 35) 15( 35) 15( 35) 15( 43) 15( 43) 15( 35) 15( 35) 15( 33) 15( 33) 15( 29) 15( 32) 15( 32) 15( 32)
15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 15( 34) 15( 26) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 43)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 26)
15( 26)
15( 26)
15( 26)
15( 26)
15( 26)
15( 24)
15( 27)
15( 27)
15( 35)
15( 35)
15( 35)
15( 33)
15( 33)
15( 33)
15( 35)
15( 35)
15( 28)
15( 28)
15( 26) 15( 26) 15( 26) 15( 32) 15( 33) 15( 33) 15( 33) 15( 35) 15( 35) 15( 43) 15( 43) 15( 43) 15( 35) 15( 33) 15( 29) 15( 29) 15( 32) 15( 32) 15( 32)
15( 35) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 0) 15( 26) 15( 26) 15( 34) 15( 34) 15( 34) 15( 42) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 35)
15( 26)
15( 35)
15( 26)
15( 35)
15( 26)
15( 35)
15( 26)
15( 35)
15( 26)
15( 24)
15( 24)
15( 27)
15( 42)
15( 27)
15( 42)
15( 27)
15( 42)
15( 27)
15( 42)
15( 43)
15( 26)
15( 35)
15( 35)
15( 33)
15( 33)
15( 33)
15( 33)
15( 28)
15( 26) 15( 26) 15( 26) 15( 32) 15( 33) 15( 33) 15( 33) 15( 35) 15( 35) 15( 43) 15( 43) 15( 43) 15( 35) 15( 33) 15( 29) 15( 29) 15( 32) 15( 32) 15( 32)
15( 35) 15( 35) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 26) 15( 26) 21( 34) 21( 34) 15( 34) 15( 42) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 35)
15( 26)
15( 34)
15( 27)
15( 34)
15( 27)
15( 35)
15( 26)
15( 35)
15( 26)
15( 35)
15( 26)
15( 35)
15( 26)
15( 41)
15( 24)
15( 24)
15( 27)
15( 34)
15( 27)
15( 34)
15( 43)
15( 42)
15( 35)
15( 42)
15( 35)
15( 33)
15( 33)
15( 33)
15( 33)
15( 28)
15( 26) 15( 26) 15( 26) 15( 32) 15( 33) 15( 33) 15( 33) 15( 35) 15( 35) 15( 43) 15( 43) 15( 43) 15( 35) 15( 33) 15( 29) 15( 29) 15( 32) 15( 32) 15( 32)
15( 35) 15( 35) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 26) 15( 34) 21( 34) 21( 34) 15( 34) 15( 34) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
16( 35)
15( 26)
15( 34)
15( 27)
15( 34)
15( 27)
16( 35)
15( 26)
15( 33)
15( 26)
15( 35)
15( 26)
15( 29)
15( 26)
15( 31)
15( 24)
15( 41)
15( 24)
15( 31)
15( 24)
15( 34)
15( 27)
15( 34)
15( 27)
15( 34)
15( 43)
15( 34)
15( 35)
15( 34)
15( 35)
15( 33)
15( 33)
15( 33)
15( 33)
15( 26) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33) 15( 33) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 35) 15( 35) 15( 29) 15( 29) 15( 32) 15( 34) 15( 34)
15( 35) 15( 29) 15( 29) 15( 31) 15( 0) 15( 0) 15( 0) 15( 26) 15( 34) 22( 34) 22( 34) 16( 34) 15( 34) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 33)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 32)
15( 32)
15( 31)
15( 31)
15( 31)
15( 24)
16( 31)
15( 24)
16( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 31)
15( 29)
15( 24)
15( 29)
15( 29)
15( 32)
图 7-6
15( 42) 15( 0) 15( 0) 15( 33) 15( 33) 15( 33) 15( 33) 15( 35) 15( 0) 15( 27) 15( 33) 15( 29) 15( 29) 15( 34)
22( 29) 21( 29) 33( 34) 33( 34) 15( 28) 15( 28)
15( 35) 15( 31) 15( 0) 15( 26) 15( 26) 15( 26) 15( 42) 17( 34) 15( 32) 15( 0) 15( 0) 15( 0) 15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
27( 29)
35( 29)
15( 32)
15( 32)
35( 29)
27( 29)
15( 31)
19( 31)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 29)
23( 29)
15( 29)
15( 29)
15( 29)
15( 29)
15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
28( 31)
35( 29)
32( 29)
15( 32)
35( 29)
28( 31)
15( 31)
19( 31)
15( 31)
15( 31)
15( 31)
15( 31)
15( 29)
35( 29)
35( 29)
15( 29)
15( 29)
15( 29)
32( 29)
15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 29) 15( 29) 15( 0) 15( 0) 15( 26)
15( 31) 15( 31) 15( 31) 15( 31) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 28( 32) 28( 32) 15( 32) 15( 0) 15( 0) 21( 33) 21( 33) 15( 33)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 41)
15( 41)
15( 41)
15( 31)
15( 31)
15( 31)
15( 31)
15( 31)
15( 29)
15( 29)
18( 29)
35( 29)
35( 29)
15( 29)
15( 29)
15( 29)
32( 29)
32( 29)
15( 32)
15( 28) 15( 40) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 35) 15( 33) 15( 33) 15( 25) 15( 26) 15( 0)
15( 41) 15( 41) 15( 25) 15( 26) 15( 26) 25( 26) 25( 26) 15( 26) 19( 26) 19( 26) 15( 32) 15( 32) 15( 32) 15( 32) 15( 0) 15( 0) 15( 33) 15( 33) 15( 33)
-8-
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 41)
15( 26)
15( 26)
21( 26)
21( 26)
32( 31)
32( 31)
16( 29)
21( 29)
21( 29)
15( 29)
15( 29)
15( 29)
15( 29)
15( 29)
15( 29)
15( 29)
15( 33)
15( 33)
15( 28) 15( 28) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 27) 15( 27) 15( 27) 15( 27) 15( 24) 15( 26) 15( 26)
15( 0) 15( 24) 15( 26) 15( 26) 15( 26) 25( 26) 25( 26) 15( 26) 19( 26) 19( 26) 15( 34) 15( 34) 15( 32) 15( 32) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 26)
15( 26)
15( 26)
21( 26)
21( 26)
32( 31)
32( 31)
16( 29)
21( 29)
21( 29)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 33)
15( 29) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 27) 15( 35) 15( 35) 15( 24) 15( 26) 15( 26)
15( 40) 15( 24) 15( 24) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 34) 15( 32) 15( 32) 15( 32) 15( 32) 15( 0) 15( 0) 15( 29) 15( 29) 15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 24)
15( 24)
15( 24)
15( 24)
15( 26)
15( 26)
15( 28)
15( 28)
15( 30)
15( 28)
16( 28)
16( 28)
16( 28)
16( 28)
15( 28)
15( 28)
15( 28)
15( 33)
15( 33)
15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 35) 15( 28) 15( 28) 15( 0) 15( 0) 15( 40)
15( 40)
15( 0) 15( 40) 15( 40) 16( 24) 16( 24) 15( 26) 15( 26) 15( 26) 21( 26) 21( 26) 15( 32) 35( 32) 35( 32) 15( 32) 15( 0) 15( 0) 21( 29) 21( 29) 15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 40)
15( 40)
15( 30)
23( 30)
23( 30)
15( 30)
15( 30)
15( 30)
26( 30)
26( 30)
21( 28)
44( 28)
44( 28)
19( 28)
15( 28)
15( 28)
33( 28)
33( 28)
15( 33)
15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33) 15( 33) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 35) 15( 28) 15( 28) 15( 0) 15( 0) 15( 24)
15( 40) 16( 30) 16( 30) 16( 24) 16( 24) 15( 26) 15( 26) 15( 26) 21( 26) 22( 34) 22( 34) 35( 32) 35( 32) 15( 32) 15( 0) 15( 0) 21( 29) 21( 29) 15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
33( 28)
15( 33)
26( 30)
26( 28)
20( 30)
23( 30)
23( 30)
15( 30)
15( 30)
15( 30)
26( 30)
44( 28)
44( 28)
19( 28)
15( 28)
15( 28)
33( 28)
15( 0)
15( 0)
15( 0)
34( 30)
33( 30)
15( 29)
15( 29)
33( 30)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
34( 30)
20( 30)
24( 30)
15( 30)
15( 30)
15( 30)
15( 30)
19( 30)
26( 28)
17( 28)
17( 28)
15( 28)
15( 28)
15( 28)
15( 0)
15( 0)
34( 30)
32( 30)
15( 29)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 29)
32( 30)
34( 30)
18( 30)
24( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
19( 30)
15( 30)
15( 28)
15( 28)
15( 28)
15( 28)
15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33) 15( 33) 15( 33) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0) 15( 27) 15( 30) 15( 30) 15( 24) 15( 30) 15( 30)
15( 30) 15( 30) 15( 30) 15( 30) 15( 24) 15( 26) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 15( 34) 15( 34) 15( 34) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 40)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 30)
15( 28)
15( 28)
15( 28)
15( 32)
15( 0) 15( 0) 15( 0) 15( 0) 15( 33) 15( 33) 15( 33) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 0) 15( 27) 15( 30) 15( 30) 15( 30) 15( 30) 15( 30)
15( 30) 15( 30) 15( 30) 15( 40) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 15( 34) 15( 34) 15( 34) 15( 0) 15( 0) 15( 0) 15( 0) 15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 30)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 30)
15( 25)
15( 40)
15( 34)
15( 34)
15( 40)
15( 41)
15( 40)
15( 31)
15( 30)
15( 31)
15( 30)
15( 31)
15( 30)
15( 24)
15( 24)
15( 28)
15( 26)
15( 28)
15( 0) 15( 0) 15( 0) 15( 43) 15( 35) 15( 33) 15( 33) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 35) 15( 35) 15( 30) 15( 30) 15( 28) 15( 28) 15( 0)
15( 30) 15( 34) 15( 26) 15( 26) 15( 26) 15( 0) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 34) 15( 34) 15( 34) 15( 0) 15( 0) 15( 0) 15( 24) 15( 24)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 34)
15( 27)
15( 34)
15( 40)
15( 25)
15( 30)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 40)
15( 25)
15( 31)
15( 31)
15( 24)
15( 31)
15( 24)
15( 31)
15( 24)
15( 29)
15( 26)
15( 29)
15( 24)
15( 24)
15( 27)
15( 34)
15( 40)
15( 0) 15( 0) 15( 0) 15( 35) 15( 35) 15( 35) 15( 35) 15( 35) 15( 35) 15( 0) 15( 0) 15( 0) 15( 35) 15( 35) 15( 33) 15( 33) 15( 28) 15( 28) 15( 0)
15( 34) 15( 34) 15( 26) 15( 26) 15( 0) 15( 0) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 26) 15( 34) 15( 26) 15( 0) 15( 0) 15( 0) 15( 24) 15( 24)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 0)
15( 34)
15( 27)
15( 34)
15( 27)
15( 25)
15( 28)
15( 25)
15( 28)
15( 25)
15( 25)
15( 35)
15( 25)
15( 27)
15( 32)
15( 32)
15( 29)
15( 24)
15( 29)
15( 24)
15( 29)
15( 24)
15( 24)
15( 42)
15( 27)
15( 24)
15( 27)
15( 34)