Professional Documents
Culture Documents
77
www.hilti.com
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + HAS-V-36 (ASTM F1554 Gr.36) 3/4
Item number: 2198030 HAS-V-36 3/4"x10" (element) / 2022791
HIT-HY 200-A (adhesive)
Effective embedment depth: hef,act = 8.000 in. (hef,limit = - in.)
Material: ASTM F1554 Grade 36
Evaluation Service Report: ESR-3187
Issued I Valid: 5/1/2021 | 3/1/2022
Proof: Design Method ACI 318-14 / Chem
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.750 in.
Anchor plate :
R lx x ly x t = 15.000 in. x 12.000 in. x 0.750 in.; (Recommended plate thickness: not calculated)
Profile: L profile (AISC), L102X102X6.4; (L x W x T) = 4.016 in. x 4.016 in. x 0.252 in.
Base material: cracked concrete, 3000, fc' = 3,000 psi; h = 18.000 in., Temp. short/long: 104/104 °F
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
Note: the HIT-HY 200 + HAS-V-36 (ASTM F1554 Gr.36) anchor is in the process of phase-out. As a result, there is limited/no inventory available.
Application also possible with HIT-HY 200 V3 + HAS-V-36 (ASTM F1554 Gr.36) under the selected boundary conditions.
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
3 1
max. concrete compressive strain: - [‰]
max. concrete compressive stress: - [ksi]
resulting tension force in (x/y)=(0.000/0.000): 4.970 [kip]
resulting compression force in (x/y)=(0.000/0.000): 0.000 [kip]
Anchor forces are calculated based on the assumption of a rigid anchor plate.
3 Tension load
Load Nua [kip] Capacity f Nn [kip] Utilization bN = Nua/f Nn Status
Steel Strength* 1.242 14.550 9 OK
Bond Strength** 4.970 32.695 16 OK
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Failure** 4.970 26.629 19 OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
Variables
2
Ase,N [in. ] futa [ksi]
0.33 58.000
Calculations
Nsa [kip]
19.400
Results
Nsa [kip] f steel f Nsa [kip] Nua [kip]
19.400 0.750 14.550 1.242
Nag = (AA ) y
Na
Na0
ec1,Na y ec2,Na y ed,Na y cp,Na Nba ACI 318-14 Eq. (17.4.5.1b)
f Nag ³ Nua ACI 318-14 Table 17.3.1.1
ANa see ACI 318-14, Section 17.4.5.1, Fig. R 17.4.5.1(b)
2
ANa0 = (2 cNa) ACI 318-14 Eq. (17.4.5.1c)
t uncr
cNa = 10 da √ 1100
ACI 318-14 Eq. (17.4.5.1d)
( )
1
'
y ec,Na = eN £ 1.0 ACI 318-14 Eq. (17.4.5.3)
1+
cNa
Na
ACI 318-14 Eq. (17.4.5.4b)
= MAX(
c ) £
c c a,min Na
y cp,Na , 1.0 ACI 318-14 Eq. (17.4.5.5b)
c ac ac
Nba = l a · t k,c · p · da · hef ACI 318-14 Eq. (17.4.5.2)
Variables
t k,c,uncr [ksi] da [in.] hef [in.] ca,min [in.] aoverhead t k,c [ksi]
2.261 0.750 8.000 ∞ 1.000 1.283
Calculations
cNa [in.] ANa [in. ]
2
ANa0 [in. ]
2
y ed,Na
10.704 953.02 458.28 1.000
Results
Nag [kip] f bond f Nag [kip] Nua [kip]
50.299 0.650 32.695 4.970
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
Ncbg = (AA ) y
Nc
Nc0
ec,N y ed,N y c,N y cp,N Nb ACI 318-14 Eq. (17.4.2.1b)
f Ncbg ³ Nua ACI 318-14 Table 17.3.1.1
ANc see ACI 318-14, Section 17.4.2.1, Fig. R 17.4.2.1(b)
2
ANc0 = 9 hef ACI 318-14 Eq. (17.4.2.1c)
( )
1
'
y ec,N = 2 eN £ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
ef
ACI 318-14 Eq. (17.4.2.5b)
= MAX(
c ) £
c 1.5h a,min ef
y cp,N , 1.0 ACI 318-14 Eq. (17.4.2.7b)
c ac ac
1.5
Nb = kc l a √ '
fc hef ACI 318-14 Eq. (17.4.2.2a)
Variables
hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.] y c,N
8.000 0.000 0.000 ∞ 1.000
'
cac [in.] kc la fc [psi]
13.798 17 1.000 3,000
Calculations
ANc [in. ]
2
ANc0 [in. ]
2
y ec1,N y ec2,N y ed,N y cp,N Nb [kip]
1,120.00 576.00 1.000 1.000 1.000 1.000 21.069
Results
Ncbg [kip] f concrete f Ncbg [kip] Nua [kip]
40.968 0.650 26.629 4.970
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
4 Shear load
Load Vua [kip] Capacity f Vn [kip] Utilization bV = Vua/f Vn Status
Steel Strength* 1.030 7.566 14 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Concrete Breakout 4.120 57.355 8 OK
Strength controls)**
Concrete edge failure in direction ** N/A N/A N/A N/A
Variables
2
Ase,V [in. ] futa [ksi]
0.33 58.000
Calculations
Vsa [kip]
11.640
Results
Vsa [kip] f steel f Vsa [kip] Vua [kip]
11.640 0.650 7.566 1.030
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
Nc0
ec,N y ed,N y c,N y cp,N Nb ] ACI 318-14 Eq. (17.5.3.1b)
f Vcpg ³ Vua ACI 318-14 Table 17.3.1.1
ANc see ACI 318-14, Section 17.4.2.1, Fig. R 17.4.2.1(b)
2
ANc0 = 9 hef ACI 318-14 Eq. (17.4.2.1c)
( )
1
'
y ec,N = 2 eN £ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
ef
ACI 318-14 Eq. (17.4.2.5b)
= MAX(
c ) £
c 1.5h a,min ef
y cp,N , 1.0 ACI 318-14 Eq. (17.4.2.7b)
c ac ac
1.5
Nb = kc l a √ '
fc hef ACI 318-14 Eq. (17.4.2.2a)
Variables
kcp hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.]
2 8.000 0.000 0.000 ∞
'
y c,N cac [in.] kc la fc [psi]
1.000 13.798 17 1.000 3,000
Calculations
ANc [in. ]
2
ANc0 [in. ]
2
y ec1,N y ec2,N y ed,N y cp,N Nb [kip]
1,120.00 576.00 1.000 1.000 1.000 1.000 21.069
Results
Vcpg [kip] f concrete f Vcpg [kip] Vua [kip]
81.935 0.700 57.355 4.120
z z
bNV = bN + bV <= 1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Condition A applies where the potential concrete failure surfaces are crossed by supplementary reinforcement proportioned to tie the
potential concrete failure prism into the structural member. Condition B applies where such supplementary reinforcement is not provided, or
where pullout or pryout strength governs.
• Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions.
• For additional information about ACI 318 strength design provisions, please go to
https://submittals.us.hilti.com/PROFISAnchorDesignGuide/
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. Reference ACI 318-14,
Section 17.8.1.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
7 Installation data
Anchor type and diameter: HIT-HY 200 + HAS-V-36
(ASTM F1554 Gr.36) 3/4
Profile: L profile (AISC), L102X102X6.4; (L x W x T) = 4.016 in. x 4.016 in. x Item number: 2198030 HAS-V-36 3/4"x10" (element) /
0.252 in. 2022791 HIT-HY 200-A (adhesive)
Hole diameter in the fixture: df = 0.812 in. Maximum installation torque: 0.10000 ft.kip
Plate thickness (input): 0.750 in. Hole diameter in the base material: 0.875 in.
Recommended plate thickness: not calculated Hole depth in the base material: 8.000 in.
Drilling method: Hammer drilled Minimum thickness of the base material: 9.750 in.
Cleaning: Compressed air cleaning of the drilled hole according to instructions
for use is required
3/4 Hilti HAS Carbon steel threaded rod with Hilti HIT-HY 200 Safe Set System
y
7.500 7.500
2.000
4 2
6.000
8.000
x
6.000
3 1
2.000
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.77
www.hilti.com
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: MSC - 01 - Angle Date: 5/17/2022
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan