Professional Documents
Culture Documents
89
www.hilti.com.kw
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + HAS-U 8.8 M20
Item number: 2237092 HAS-U 8.8 M20x300 (element) / 2045030
HIT-HY 200-A (adhesive)
Effective embedment depth: hef,act = 200.0 mm (hef,limit = - mm)
Material: 8.8
Evaluation Service Report: ESR-3187
Issued I Valid: 1.05.2021 | 1.03.2022
Proof: Design Method ACI 318-08 / Chem
Stand-off installation: without clamping (anchor); restraint level (anchor plate): 2.00; eb = 20.0 mm; t = 10.0 mm
2
Hilti Grout: CB-G EG, epoxy, fc,Grout = 120.00 N/mm
Anchor plate :
R lx x ly x t = 220.0 mm x 220.0 mm x 10.0 mm; (Recommended plate thickness: not calculated)
Application also possible with HVU2 + HAS-U 8.8 M20 under the selected boundary conditions.
More information in section Alternative fastening data of this report.
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
3 Tension load
Load Nua [kN] Capacity f Nn [kN] Utilization bN = Nua/f Nn Status
Steel Strength* N/A N/A N/A N/A
Bond Strength** N/A N/A N/A N/A
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Failure** N/A N/A N/A N/A
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
4 Shear load
Load Vua [kN] Capacity f Vn [kN] Utilization bV = Vua/f Vn Status
Steel Strength* 11.250 56.400 20 OK
Steel failure (with lever arm)* 11.250 17.807 64 OK
Pryout Strength (Concrete Breakout 45.000 239.991 19 OK
Strength controls)**
Concrete edge failure in direction ** N/A N/A N/A N/A
Variables
Ase,V [mm ]
2
futa [N/mm ]
2
aV,seis
245 800.00 0.700
Calculations
Vsa [kN]
117.500
Results
Vsa [kN] f steel f eb f Vsa [kN] Vua [kN]
117.500 0.600 0.800 56.400 11.250
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
M aM · M s
Vs = bending equation for stand-off
Lb
Ms = Ms
0
(1 - fNN )
ua
sa
resultant flexural resistance of anchor
0
Ms = (1.2) (S) (fu,min) characteristic flexural resistance of anchor
( N
1 - f ua
Nsa ) reduction for tensile force acting simultaneously with a shear force on the anchor
3
p(d)
S = elastic section modulus of anchor bolt at concrete surface
32
Lb = z + (n)(d0) internal lever arm adjusted for spalling of the surface concrete
f VM
s ³ Vua ACI 318-08 Eq. (D-2)
Variables
aM fu,min [N/mm ]
2
Nua [kN] f Nsa [kN] z [mm] n d0 [mm]
2.00 800.00 0.000 127.400 25.0 0.500 20.0
Calculations
0
Ms [kNm] (1 - fNN )
ua
sa Ms [kNm] Lb [mm]
0.519 1.000 0.519 35.0
Results
M
Vs [kN] f steel f VM
s [kN] Vua [kN]
29.678 0.600 17.807 11.250
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
Nc0
ec,N y ed,N y c,N y cp,N Nb ] ACI 318-08 Eq. (D-31)
f Vcpg ³ Vua ACI 318-08 Eq. (D-2)
ANc see ACI 318-08, Part D.5.2.1, Fig. RD.5.2.1(b)
2
ANc0 = 9 hef ACI 318-08 Eq. (D-6)
( )
1
'
y ec,N = 2 eN £ 1.0 ACI 318-08 Eq. (D-9)
1+
3 hef
ef
ACI 318-08 Eq. (D-11)
= MAX(
c ) £
c 1.5h a,min ef
y cp,N , 1.0 ACI 318-08 Eq. (D-13)
c ac ac
Nb = kc l √f'c h1.5
ef ACI 318-08 Eq. (D-7)
Variables
kcp hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm]
2 200.0 0.0 0.0 ∞
'
y c,N cac [mm] kc l fc [psi]
1.000 343.9 17 1 5,076
Calculations
ANc [mm ]
2
ANc0 [mm ]
2
y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
518,400 360,000 1.000 1.000 1.000 1.000 119.043
Results
Vcpg [kN] f concrete f Vcpg [kN] Vua [kN]
342.844 0.700 239.991 45.000
5 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Condition A applies where the potential concrete failure surfaces are crossed by supplementary reinforcement proportioned to tie the
potential concrete failure prism into the structural member. Condition B applies where such supplementary reinforcement is not provided, or
where pullout or pryout strength governs.
• ACI 318 does not specifically address anchor bending when a stand-off condition exists. PROFIS Engineering calculates a shear load
corresponding to anchor bending when stand-off exists and includes the results as a shear Design Strength!
• Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions.
• The present version of the software does not account for special design provisions for overhead applications. Refer to related approval (e.g.
section 4.1.1 of the ICC-ESR 2322) for details.
• For additional information about ACI 318 strength design provisions, please go to
https://submittals.us.hilti.com/PROFISAnchorDesignGuide/
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
6 Installation data
Anchor type and diameter: HIT-HY 200 + HAS-U 8.8 M20
Profile: I profile, ; (L x W x T x FT) = 203.0 mm x 204.0 mm x 7.0 mm x 11.0 Item number: 2237092 HAS-U 8.8 M20x300 (element) /
mm 2045030 HIT-HY 200-A (adhesive)
Hole diameter in the fixture: df = 22.0 mm Maximum installation torque: 150 Nm
Plate thickness (input): 10.0 mm Hole diameter in the base material: 22.0 mm
Recommended plate thickness: not calculated Hole depth in the base material: 200.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 244.0 mm
Cleaning: Compressed air cleaning of the drilled hole according to instructions
for use is required
M20 Hilti HAS-U Carbon steel threaded rod with Hilti HIT-HY 200
y
110.0 110.0
50.0
3 4
110.0
120.0
x
110.0
1 2
50.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
7 Alternative fastening
7.1 Alternative fastening data
M20 Hilti HAS-U Karbon çeliği Dişli rod ile Hilti HVU2
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.89
www.hilti.com.kw
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: A1-11-PC-C03___20231129 Date: 29.11.2023
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan