Professional Documents
Culture Documents
HARMONIZED
Head Room 4500
3x380V
Door Height 2300
Voltage, V
Main switch current, A 20
N N
Power, kW 6.7
Starting current, A 24
Rated current, A 16
BUILDERS WORKS
1. The lift shaft must be constructed to accommodate the loadings indicated on our drawings and with a minimum 7KN high density block.
2. The lift shaft must be plumb-0mm, +25mm over the full length, sizes must comply with our drawing. The lift finished floor level datum must be
marked at each entrance.
Total Height 21500
3. The shaft must comply with the fire and building regulations.
4. To ensure the correct functioning of the equipment in the well and machinery space(s), i.e. taking into account the heat dissipated by the equipment,
the ambient temperature in the well and the machinery space(s) is assumed to be maintained between + 5 °C and + 40 °C.
5. Provide suitable access into building and lift shafts suitable for a component length of 5.0M.
6. The pit must be permanently watertight and the surface must be smooth, level and painted. The concrete base should be designed to take the loads
E E stated on the drawing. The pit depth must be accurate to +/-20mm.
7. Provide pad stones or steel supports where necessary.
8. Provide and fix temporary guards around the lift entrances to comply with health and safety at work act requirements.
9. The front return walls shall be built as shown and finished following the final fixing and positioning of our entrance frames. All recesses shall be
Travel 15500
A
Contract No
Confirmed
Shaft Section E-E Shaft Section N-N C
Shaft Depth
X
D Z W B
Shaft Width
J
445 DBG 1180 145 445 DBG 1180 145
150
150
350
350
815
815
Cabin Depth 1400
CW-DBG 1000
Shaft Depth 1770
C.O.P.
C.O.P.
955
955
420
420
360
20 30 70
20 30 70
220
220
50 50
50 50
4
360
356
331
120 120
Page Version
A Studied
Name
IliasTsaparelis
Signature Date
22/2/2022
Installation Drawings For
J
Designed EmmanouilParharidis 22/2/2022
Traction Lift
2/ 7 3.0
Checked IliasTsaparelis 22/2/2022
Contract No
Confirmed
Pit section G-G Cabin Buffer Counterweight buffer
445 DBG 1180 145
40
60
350 F6
1075
815
40
CW-DBG 1000
F2 F4 F1 F3
60
1000
200
Safety space
700
955
500x700x1000
920
F5
420
Load Name
1035
Load Value(N) Load Points Sketch Notes
Fx
Fy sling mountings guide
Fy 491
Fx
Fz
Fz 14552
On the cabin buffer on the area of
F1 58209 165x165mm
On the counterweight buffer on the
F2 45848 area of 165x165mm
On the heel of the car sling guides on Loads act at different
F3 16124 the area of 150x150mm
On the heel of the car sling guides on times and emergency
F4 20489 the area of 150x150mm
Shaft Axis On the heel of the counterweight
F5 785 guides on the area of 150x150mm
On the heel of the counterweight
F6 11136 guides on the area of 150x150mm
Fcx 29 Pressures on the
x
Fc
Fcy Fcy counterweight
205
x
Fc
mountings guide
1770
Fcz
Fcz 0
F7 F7
On the
mountings
shaft door
Constant load
Cabin Axis F7 1500 in the wall
plane
920
885
F7 F7
Door Axis
1035
Contract No
1770
Confirmed
Mounting Brackets Plan View with Scaffold
350
50
150
1370
1595
Cabin
Guide
Counterweight
Guide
250
125
4x5000
11x2000
Guide Joint
Scaffold to be erected as shown on the drawing.
First stage 1000mm above ground floor level and
then every 2000mm.
Bracket Contract No
Confirmed
Machine room section F-F
1770
140 319 1152 159
Monorail 5000Н
111
409
Ø5 0
690
180
300
180
320
1770 180
180
180
180
760
2500
200
2000
Power plug
1500
Machinery
lighting
1200
Light switch
Hatch
2000
Work area
710х750
600
Controller
ELECTRICAL REQUIREMENTS
The above notes are for guidance and any alterations or variations must be agreed by the installer in writing prior to the Designed EmmanouilParharidis 22/2/2022
Traction Lift
5/ 7 3.0
commencement of the contract. Checked IliasTsaparelis 22/2/2022
Contract No
Confirmed
Vertical section of shaft J-J
Schematic diagram of the kinematic
Traction pulley
Suspended
cable
Ø320
Distances with the
cabin at the top
1190
overtravel
1800
1890
500 Grounds
maintenance
Head Room 4500
position on the
1000
700
roof of the car
when stopped in
the "Revision"
Internal Cabin Height 2400
0
Φ32
Cabin
Diverting
pulley
Top Car Overtravel 100
Diverting
pulley
Counterweight
A
C
700
Internal Cabin Height 2400
Bottom Car Overtravel 100
50
27
300
230
50
2600
Door Height 2300
300
2650
2580
300
300
1500
900
900
2580
2650
2300
2300
70 Door Width 800 70 120 Door Width 800 120
K L
50
Last floor
100
Stop Marking
Door Height 2300
2530
Ø40
110
38
100
2580
27
4 360
80 50
20
50
300 50
20
1800