Professional Documents
Culture Documents
1 Generality
• The values indicated in this instruction are based in the Standard ASTM A 234/A 234MA-2019
and ASME B16.9M-2018.
• Mechanical Properties, Chemical Composition and dimensions given in this standard are for
reference only. For supply, the supplier must consider the last edition of the respective standard.
• Additional requirements can be indicated in the purchase order.
2 Mechanical Properties
REMARKS :
A
1) WPB fittings manufactured from plate shall have a minimum elongation of 17 %.
B
2) For each 0.79 mm decrease in wall thickness below 7.94 mm, a deduction of 1.5 % for longitudinal and 1.0 %
for transverse from the values shown above is permitted. The following table gives the minimum value for
various wall thickness.
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third
parties without express authorization is strictly forbidden. Copyright by GE – GE Confidential
Name : HS-PEL02ASP-000000EC Rev : - Release : 2022/06/14 10:57 AM
Hydro Technical Standard HS-PEL02ASP-000000EC
Engineering Procurement Specification Revision: Date: Page:
Pipe, Tubes & Accessory: Elbow - 22/02/2022 2/5
3 Chemical Composition:
Element Composition %
Carbon 0.30 max
Manganese 0.29 - 1.06
Phosphorus 0.05 max
Sulfur 0.058 max
Silicon 0.10 min
Chromium 0.40 max
Molybdenum 0.15 max
Nickel 0.40 max
Copper 0.40 max
Vanadium 0.08 max
REMARKS :
A
1) Fittings made from bar or plate may have 0.35 max carbon.
B
2) Fittings made from forgings may have 0.35 max carbon and 0.35 max silicon with no minimum.
C For
3) each reduction of 0.01 % below the specified maximum carbon, an increase of 0.06 % manganese above
the specified maximum will be permitted, up to a maximum of 1.65 %.
D
4) The sum of Copper, Nickel, Chromium, and Molybdenum shall not exceed 1.00 %.
E
5) The sum of Chromium and Molybdenum shall not exceed 0.32 %.
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third
parties without express authorization is strictly forbidden. Copyright by GE – GE Confidential
Name : HS-PEL02ASP-000000EC Rev : - Release : 2022/06/14 10:57 AM
Hydro Technical Standard HS-PEL02ASP-000000EC
Engineering Procurement Specification Revision: Date: Page:
Pipe, Tubes & Accessory: Elbow - 22/02/2022 3/5
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third
parties without express authorization is strictly forbidden. Copyright by GE – GE Confidential
Name : HS-PEL02ASP-000000EC Rev : - Release : 2022/06/14 10:57 AM
Hydro Technical Standard HS-PEL02ASP-000000EC
Engineering Procurement Specification Revision: Date: Page:
Pipe, Tubes & Accessory: Elbow - 22/02/2022 4/5
4.2 Tolerances
4.2.1 Dimensional Tolerance
Remarks:
1) Dimensions are in millimeters.
2) Tolerances are equal plus and minus except as noted.
5 Delivery Conditions
5.1 Identification
Each elbow shall be marked atleast with following information as per ASME B16.9.
• Manufacturer name (or symbol);
• Specification Number;
• Grade & Size;
• Compliance.
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third
parties without express authorization is strictly forbidden. Copyright by GE – GE Confidential
Name : HS-PEL02ASP-000000EC Rev : - Release : 2022/06/14 10:57 AM
Hydro Technical Standard HS-PEL02ASP-000000EC
Engineering Procurement Specification Revision: Date: Page:
Pipe, Tubes & Accessory: Elbow - 22/02/2022 5/5
Codification: H S – P EL 0 2 AS P – 1 0 0 0 4 0
Schedule: SCH 40
Size: DN 100
Protection: Primer Coating
7 Revision History
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third
parties without express authorization is strictly forbidden. Copyright by GE – GE Confidential