Professional Documents
Culture Documents
塔式起重机型式试验额定起重力矩为 1050t·m。
The test rated lifting torque of tower crane is 1050t·m.
2)总图图号:XGT 1050 - 50 S
2) General drawing number: XGT 1050 - 50 S
额定起重力矩(t·m)
Rated load moment (t·m)
徐工塔机内部代号
XCMG tower crane internal code
图 Figure 2.2-1
图 Figure 2.2-2
图 例 Legend
塔身 平衡重 起重臂
2 9 16
Tower Body Counter Weight Jib
液压顶升系统 回转机构 吊钩
4 11 18
Hydraulic Jacking System Slewing Mechanism Hook
上支座 起重量限制器
7 14
Upper support Load Lifting Limiter
额定起重力矩
t·m 1050
Rated lifting moment
最大起重量
t 50
Hoisting Capacity
最大幅度
Maximum Radius 80
幅度(m) (m)
Radius (m) 最小幅度
Minimum Radius 4.4
(m)
倍率 Fall α=2 α=4
起升机构 起重量
4.5 12.5 25 9 25 50
Hoisting Mechanism Lifting Weight (t)
功率 Power (kW) 30
液压系统
Hydraulic System 额定工作压力
Rated working 26
pressure (MPa)
80 61.5 75 57.5
70 57.5 65 53.5
平衡重
60 52 55 48
Counter Weight
50 57.5 45 53.5
40 48 35 61.5
30 57.5
顶升状态
12
Jacking state
塔顶设计风速 工作状态
20
(3s 时距平均瞬时风速) Operating State
型号 Model / 139LVF125DB2
额定单绳拉力
KN 125
Rated single rope tension
型号 26-DL1315HK-1960-605kN (右旋同向捻)
/
Model Right hand twist in the same direction
钢丝绳 公称直径
mm 26
Steel Wire Nominal Diameter
Rope 最大线速度
Maximum Line m/min 204
Velocity
卷筒 容绳量/层数
m/r 1180/7
Lifting drum Rope Capacity/Layers
型号 Model / YZP2-315L2-4/30L/25Hz/139kW
起升机构 Hoisting Mechanism
额定功率
kW 139
Rated Power
电机
额定频率
Motor Hz 25
Rated Frequency
额定转速
r/min 718
Rated rotate speed
动器 出厂调整值
N.m 3250
High speed Factory adjusted value
end electric
制动钳型号
hydraulic / SBD250-A-1878×30.II.RL.WL
Brake pliers model
block brake
低速端安全
制动器 泵站型号
/ YZBA13-05/A
Low speed Pumping station model
safety brake
型号 Model / 19DVF33
最大牵引力
kN 33
Maximum Traction Force
最大变幅范围
m 80
Maximum Luffing Range
钢丝绳 规格型号 16 8×K26SW-IWRC1770-197kN
Steel Wire Specification and / (右旋交互捻 )
Rope Model Right hand twist in the same direction
变幅机构 Luffing Mechanism
型号
/ YVFE3-180M-4H 18.5kW
Model
额定功率
kW 18.5
Rated Power
额定频率
电机 Hz 50
Rated Frequency
Motor
转速
r/min 1470
Rotate speed
最大制动力矩
Maximum Braking N.m 200
Torque
型号
减速机 / 24JXF33.04
Model
Reduction
速比
gears / 115.2
Speed ratio
型号 Model / JH15T3
型号
/ YTRVFW160L3-6F1 15kW
Model
回转电机
功率
Slewing Mechanism kW 3×15kW
Power
Motor
转速
r/min 898(50Hz)
Rotate speed
型号
回转机构 Slewing Mechanism
/ JH15T3
Model
减速机
减速机速比
Reduction gears
Reducer Speed / 160
Ratio
模数
mm 16
Modulus
输出端齿轮参数 齿数
/ 14
Output Gear Number of Teeth
Parameters 变位系数
Modification / +0.5
Coefficient
主机总速比
/ 1497
Total Speed Ratio of Main Engine
主机转速
r/min 0.6
Rotational Speed of Main Engine
型号
/ Y3-200L-4 FY 30kW
Model
电机 功率
kW 30
Motor Power
转速
r/min 1470
Rotate speed
Hydraulic System
流量
液压系统
L/min 53.5
液压泵站 Flow Rate
Hydraulic 额定工作压力
power unit Rated working MPa 26
pressure
缸/杆直径
顶升油缸 Cylinder/Rod mm 280/200
Jacking Diameter
cylinder 顶升速度
m/min 0.43
Jacking Speed
1)以上各臂长起重性能根据塔机独立固定高度(81m)计算而得出。当起升高度大
于 81m 时,性能曲线中的起重量必须降低。
2)计算方法为:计算高度的起重量=性能表中的起重量-每米钢丝绳的重量×(计算
高度-81)×倍率。(单位,高度:m;重量:kg,其中钢丝绳每米的重量为 3.24kg)
1) The lifting performance of the above jib lengths is calculated according to the
Independent Stationary height (81m) of the tower crane. When the hoisting height is
greater than 81m, the hoisting weight in the performance curve must be reduced.