Professional Documents
Culture Documents
ENGINEERING DRAWING N2
(8090272)
290Q1G2112
6. All drawings to be drawn neatly using your own drawing instruments, unless
otherwise specified.
7. Only the candidate information on the DRAWING SHEET must be done in ink.
All other drawing work must be done in pencil.
8. All drawings must conform to the latest SANS 10111 Codes of Practice.
10. A balanced layout is important, and candidates will be penalised for poor
planning.
NOTE: Answer this question on the attached ANSWER SHEET and submit with
DRAWING SHEET.
1.1 Write down the meaning of the following abbreviations:
1.1.1 CHAM
1.1.2 ASSY
1.1.3 CSK HD
(3 × 1) (3)
1.2 Name TWO types of CAD software used in engineering industry. (2)
1.4.2 Write down what the THREE elements of the welding symbol
represents in FIGURE 1.
(b)
(a)
(c)
FIGURE 1 (4)
[14]
FIGURE 2 [12]
FIGURE 3 (on the next page) shows a front view and top view of a pulley coupling in
first-angle orthographic projection. The coupling is joined by means of two M10 bolts and
hexagonal nuts. The bolts are in their correct working position however, the securing
nuts have been omitted.
3.1 Draw, to scale 1:1, the following views in first-angle orthographic projection:
3.1.1 A full sectional front view on cutting plane B-B, with the securing nuts
in position. (9)
3.2 Print the following title and scale centrally beneath the layout.
PULLEY COUPLING
SCALE 1:1 (2)
FIGURE 3 [22]
FIGURE 4
[14]
QUESTION 5: INTERPENETRATION
FIGURE 5 (below) shows two views of a T-end, in first-angle orthographic projection,
without interpenetration lines.
FIGURE 5
Redraw, to scale 1:1, the TWO given views and show the following:
FIGURE 6 (on the next page) shows two views of an axle shaft connector in third angle
orthographic projection.
6.1 Draw, to scale 1:1, the following views of the axle shaft connector in third-angle
orthographic projection:
6.2 Insert the third-angle orthographic projection symbol in a position below the title
and scale (1)
6.3 At A, indicate that a surface texture with a roughness value of 25µm must be
produced without the removal of material. (2)
FIGURE 6 [25]
TOTAL: 100
Copyright reserved
(8090272)
ANSWER SHEET:
EXAMINATION NUMBER:
CENTRE NUMBER:
1.1 1.1.1
1.1.2
1.1.3
(3 × 1) (3)
1.2 1.2.1
1.2.2
(Any 2 × 1) (2)
1.3
(5 × 1) (5)
1.4 1.4.1
1.4.2(a)
1.4.2(b)
1.4.2(c)
(4 × 1) (4)
[14]
Copyright reserved
MARKING GUIDELINE
NATIONAL CERTIFICATE
ENGINEERING DRAWING N2
12 August 2021
1.1.2 ASSEMBLY
1.2 AutoCAD
TurboCAD
Solid Work
Inventor
any other applicable software
(ANY 2 x 1) (2)
1.3
Correctness 3
Accuracy 1
Line work 1
TOTAL: 5
(5)
1.4.2(c) On site
(4)
[14]
2
4
2
1
FIGURE 2
7
5
6
MARKING CRITERIA
Correctness 8
Line work 2
Accuracy 1
Layout and neatness 1
TOTAL: 12
√ 4 √ 4
5 5
2 √ √ 3 √ 2
1
1
4 4
√ √
2 √ √ 3 √ 2
√ 7 8 √ 7
√
6 6
√ √
1 9
1
0
0
8
√
MARKING CRITERIA
Correctness:
FV 9
TV 6
Title and scale 2
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 22
FV
4 2 marks for bolts and thread (½ mark for bolt & ½ mark for 2 marks
thread x 2)
5 2 marks for HEXAGONAL NUTS in correct position 2 marks
TOTAL 9 marks
TV
QUESTION 4: ISOMETRIC
3
√
2
1
1
√
2 √ 3
√ 4
√
3
√
4
√ √ √
2 √
4 1
4
1
P
MARKING CRITERIA
Correctness:
Right Plane 2
Front Plane 1½
Top Plane 2½
Half Circle 2
Point P 1
Linework 2
Accuracy 2
Layout & Neatness 1
TOTAL: 14
QUESTION 5: INTERPENETRATION
√
3
√
4
√
√
2
√
4
√
1
√
√
√
√
1
3
4
√
2
√
4
√
√
√
3
4
MARKING CRITERIA
Correctness 2
Construction Lines 3
Interpenetration curve 3
Linework 2
Accuracy 2
Layout & Neatness 1
TOTAL: 13
Copyright reserved Please turn over
MARKING GUIDELINE -10-
ENGINEERING DRAWING N2
√
7
√
9
8
√
√ 7
8
√
9
√
√
6
3
A
1
√
B
1
√
D
2
√
C
√
√
F
1
√
4
√
√
√
E
F
√
MARKING CRITERIA
Correctness:
FV 6
LV 4
TV 6
Projection symbol 1
Line work 3
Accuracy 2
Layout and neatness 1
Surface texture symbol 2
TOTAL: 25
LV
6 1 Mark for the U GAP ENDS (1/2 mark each) 1 mark
7 1 Marks for the U GAP (back part) 1 mark
8 1 Mark top piece of PIPE 1 mark
9 1 Mark bottom piece of PIPE 1 mark
TOTAL 4 mark
TV
A 1 mark for U GAP sectioned 1 mark
B 1 Mark for SHOULDER sectioned 1 mark
C ½ mark for sectioned PIPE ½ mark
D ½ mark for Ø 30 HOLE ½ mark
E 1 mark for Ø12 HOLES not sectioned (½ mark each) 1 mark
F 2 marks for FORK ENDS sectioned (½ mark on either side of 2 marks
Ø12 hole)
TOTAL 6 marks
TOTAL: 100
Copyright reserved
NATIONAL CERTIFICATE
ENGINEERING DRAWING N2
(8090272)
16 February 2022 (X-paper)
09:00–13:00
REQUIREMENTS: A2 drawing sheet (BOE 8/20)
284Q1E2216
6. All drawings to be drawn neatly using your own drawing instruments, unless
indicated differently.
7. Only the candidate information on the drawing sheet must be done in ink. ALL
other drawing work must be done in pencil.
8. All drawings must conform to the latest SANS 10111 Codes of Practice.
10. A balanced layout is important, and candidates will be penalised for poor
planning.
NOTE: Answer this question on the attached ANSWER SHEET and submit with
DRAWING SHEET. All answers to be PRINTED in pencil.
1.2.1 Counterbore
❈ (4 × 1) (4)
1.4 Give the names of FIVE positive locking devices, with reference to nuts. (5)
[15]
FIGURE 1
[12]
FIGURE 2 (on the next page) shows the primary views of a heavy-duty hinge in
first-angle orthographic projection.
❈
The hinge is joined together by means of an M30 bolt and a hexagonal nut.
The bolt is in its correct working position; however, the securing nut has been omitted.
3.1 Draw, to scale 1:1, the following views in first-angle orthographic projection:❈
3.1.1 A full sectional front view on cutting plane A–A with the securing nut
in position. (8)
❈
3.1.2 An outside left view, with the securing nut in position.
3.2 Insert the first-angle orthographic projection symbol below the title and scale. (1)
FIGURE 2
[20]
Copyright reserved Please turn over
(8090272) -6-
QUESTION 4: ISOMETRIC ❈
FIGURE 3 (below) shows two views of a casting drawn in first-angle orthographic
projection.
FIGURE 3
Do not redraw the given views but draw to scale 1:1 an isometric view of the casting.
QUESTION 5: INTERPENETRATION
FIGURE 4 (below) shows the front and top view of two cylinders that intersect at right
angles.
❈
Draw to a scale of 1:1, the following:
5.3 All construction lines needed to project the interpenetration curve. (3)
FIGURE 4
[13]
FIGURE 5 (on the next page) shows a front view and a right view of a shaft bracket in
third-angle orthographic projection.
❈
6.1 Draw to scale 1:2 and in third-angle orthographic projection the following views:
6.2 Print the following title and scale beneath the layout.
SHAFT BRACKET
SCALE 1:2 (2)
6.3 Insert the third-angle orthographic projection symbol below the title and scale. (1)
6.4 At point A, insert the machine symbol to indicate the surface texture roughness
value of 6,3 µm without the removal of material. (2)
FIGURE 5
[25]
TOTAL: 100
Copyright reserved
(8090272)
EXAMINATION NUMBER:
CENTRE NUMBER:
ANSWER SHEET:
❈
1.1
1.2 1.2.1
❈
1.2.2
1.2.3
(3 × 1) (3)
❈
1.3
(ANY 4 × 1) (4)
1.4 ❈
(ANY 5 × 1) (5)
[15]
Copyright reserved
MARKING GUIDELINE
NATIONAL CERTIFICATE
ENGINEERING DRAWING N2
16 February 2022
1 2 6
8
√
5
8
√
7
3 4
MARKING CRITERIA
Correctness 8
Line work 2
Accuracy 1
Layout and neatness 1
TOTAL: 12
5 √ √ B
2 √ √ 2 A A
√ √
√
1 5 1 √
√ E
√
6 √ √
C C
4 √
√
D
√
√ 1 3 1
√ D
√
√ 4
6
√
√ √
C
√ √1 C
1
B √
3 √
MARKING CRITERIA
Correctness:
FV 8
LV 6
Projection symbol 1
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 20
SECTIONED FV
LV
[20]
QUESTION 4: ISOMETRIC
3 √
4
√
√3 1
2
2
√
4
3 √ 1
3 √
4 √ 4
√
√
4
√ 4
MARKING CRITERIA
Correctness 9
Point P in correct position 1
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 15
2 √
3 √ 2
3
4
4
1 1 √
√
3 4
MARKING CRITERIA
Correctness:
FV, TV 2
Construction lines (to project curve) 3
Interpenetration curve 3
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 13
MARK ALLOCATION FOR CORRECTNESS
1 1 mark for the front view and auxiliary view 1 mark
2 1 mark for the top view and auxiliary view 1 mark
3 3 marks for the construction lines (to project the curve) 3 marks
4 3 marks for the interpenetration curves 3 marks
√ √ √ √
A B C
B C
√
1 √
1 8
7
√ 3 3 √
√ 1 1 √
4 √ √ 4 4 √ 6
5
√ 1
1 √
2
√ 1
MARKING CRITERIA
Correctness:
Sectional FV 7
Sectional RV 4
TV 3
Title & scale 2
Projection symbol 1
Machine symbol 2
Line work 3
Accuracy 2
Layout and neatness 1
TOTAL: 25
FULL SECTIONAL FV
1 3½ marks for sectioning 3 ½ marks
2 1 mark for the Ø26 hole not sectioned 1 mark
3 1 marks for the Ø16 holes not sectioned 1 mark
4 1½ marks for the Ø 64 holes and the Ø 70 hole not sectioned 1 ½ marks
TOTAL 7 marks
SECTIONAL RV
5 1 mark for Ø 70 hole not sectioned 1 mark
6 1 mark for sectioning 1 mark
7 1 mark for Ø 16 hole not sectioned 1 mark
8 1 mark for mounting bracket 1 mark
TOTAL 4 marks
TV
A 1 mark for pipe support 1 mark
B 1 mark for mounting bracket 1 mark
C 1 mark for the ridge support 1 mark
TOTAL 3 marks [25]
TOTAL: 100
Copyright reserved
NATIONAL CERTIFICATE
ENGINEERING DRAWING N2
(8090272)
282Q1A2213
7. All drawings should be drawn neatly using your own drawing instruments,
unless otherwise specified.
9. All drawings must conform to the latest SANS 10111 Code of Practice.
11. A balanced layout is very important and candidates will be penalised for poor
planning.
1.1
DRAWING SHEET.
Choose a description from COLUMN B that matches the use of the machine
screw type in COLUMN A. Write only the letter (A–D) next to the question
number (1.1.1–1.1.4) on the ANSWER SHEET (attached).
COLUMN A COLUMN B
1.1.1 round-head screw A mostly used on covers for various types of
panels on machines
1.1.2 countersunk-head B used regularly in light engineering
screw
1.1.3 socket-head screw C used extensively in the electrical industry
(4 × 1) (4)
Calculate the dimensions according to the required proportions for (a) to (e)
represented on this figure and write only the answer next to the letter (a–e) on
the ANSWER SHEET.
(a) (c)
(e)
(b)
(d)
FIGURE 1
(5 x 1) (5)
[12]
FIGURE 2
[10]
FIGURE 3 on the next page shows an outside front view and an outside left view of a
pipe guide in first-angle orthographic projection.
3.1
Draw, to scale 1:1, the following views in first-angle orthographic projection:
3.2 Insert the following title and scale centrally beneath the layout:
PIPE GUIDE
SCALE 1:1 (2)
3.3 Draw the symbol for the first-angle orthographic projection beneath the title
and scale. (1)
3.5
produced by a milling machine.
At B: Indicate that machining is not permitted on this plane
(3)
(2)
FIGURE 3
[25]
Copyright reserved Please turn over
(8090272) -7-
Do not draw the given views, but draw to scale 1:1, an isometric view of the workpiece.
Point P must be the lowest point.
FIGURE 4
[15]
Copyright reserved Please turn over
(8090272) -8-
QUESTION 5: INTERPENETRATION
FIGURE 5 shows two views of a forked end without the interpenetration lines.
5.1 Redraw the two views in first-angle orthographic projection to scale 1:1. (4)
5.2 Show all the construction lines needed to project the interpenetration curve. (3)
FIGURE 5
[15]
Copyright reserved Please turn over
(8090272) -9-
FIGURE 6 on the next place shows a front view and a top view of a bracket in
third-angle orthographic projection.
Draw to scale 1:1 and in third-angle orthographic projection the following views of the
bracket:
6.4 Insert the third-angle orthographic projection symbol centrally beneath the
layout. (1)
FIGURE 6
[23]
TOTAL: 100
Copyright reserved Please turn over
(8090272)
EXAMINATION NUMBER:
ANSWER SHEET
QUESTION 1
1.1 1.1.1
1.1.2
1.1.3
1.1.4
(4 × 1) (4)
1.2 1.2.1
1.2.2
1.2.3
(3 × 1) (3)
1.3 (a)
(b)
(c)
(d)
(e)
(5 × 1) (5)
[12]
Copyright reserved
MARKING GUIDELINE
NATIONAL CERTIFICATE
ENGINEERING DRAWING N2
13 July 2022
1.1 1.1.1 B
1.1.2 C
1.1.3 D
1.1.4 A
(4 × 1) (4)
1.3 (a) 14
(b) 20
(c) 16
(d) 6
(e) 2
(5 × 1) (5)
[12]
4✓
√
✓2
3
1
✓
2
✓
√ 4
3
✓
MARKING CRITERIA
Correctness 6
Line work 2
Accuracy 1
Layout and neatness 1
TOTAL: 10
√
7
✓ 10
✓
✓
√ 8
9
✓
✓
10
6
✓
√
✓
10
✓
√
8
✓
5 √
✓
4
✓ 5
√3
5 ✓
✓
2
√
✓ ✓
1
√
5
MARKING CRITERIA
Correctness
FS FV 6
FS LV 6
Title and scale 2
FAOP symbol 1
Surface symbols A & B 5
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 25
FSFV
SLV
3 √
√
2
√
1 2
√ √ √
2
3
✓ √ 3
√ 4
3
✓ 4
1
✓5 √
√
2
1 √
MARKING CRITERIA
Correctness 9
Point P in correct position 1
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 15
QUESTION 5: INTERPENETRATION
1 1
√ √
✓ 3 √ 3√
4 ✓
4
✓
4
√ √
3 3
1
✓
3 √
√
3
2
✓
2
✓
MARKING CRITERIA
Correctness
FV, TV 4
Construction lines (to project curve) 3
Interpenetration curve 3
Line work 2
Accuracy 2
Layout and neatness 1
TOTAL: 15
C
√
F√
D√ E
√
√
E
D√
C √ F√
7
√ 8√
8√
4√
6√
3√ 9✓
5✓
B✓
8√ 8√
A A
√ √
2√ 1✓ 2√ 8√ 8√
MARKING CRITERIA
Correctness
S–FV 5
S–RV 6
TV 4
Projection symbol 1
Line work 3
Accuracy 2
Layout and neatness 2
TOTAL: 23
S–FV
S–RV
TV
TOTAL: 100
Copyright reserved