Professional Documents
Culture Documents
gehealthcare.com
Technical
Publications
2326235
Revision 7
Operating Documentation
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
REV 7 2326235
警告 • 本维修手册仅提供英文版本。
(ZH-CN) • 如果维修服务提供商需要非英文版本,客户需自行提供翻译服务。
• 未详细阅读和完全理解本维修手册之前,不得进行维修。
• 忽略本警告可能对维修人员,操作员或患者造成触电、机械伤害或其他形式的
伤害。
a
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
b
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
警告 • このサービスマニュアルには英語版しかありません。
(JA) • サービスを担当される業者が英語以外の言語を要求される場合、翻訳作業は
その業者の責任で行うものとさせていただきます。
• このサービスマニュアルを熟読し理解せずに、装置のサービスを行わないで
ください。
• この警告に従わない場合、サービスを担当される方、操作員あるいは患者さ
んが、感電や機械的又はその他の危険により負傷する可能性があります。
c
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
d
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
e
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
f
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
REV 7 2326235
DAMAGE IN TRANSPORTATION
All packages should be closely examined at time of delivery. If damage is apparent write “Damage In Shipment” on ALL
copies of the freight or express bill BEFORE delivery is accepted or “signed for” by a GE representative or hospital receiving
agent. Whether noted or concealed, damage MUST be reported to the carrier immediately upon discovery, or in any event,
within 14 days after receipt, and the contents and containers held for inspection by the carrier. A transportation company
will not pay a claim for damage if an inspection is not requested within this 14 day period.
To file a report:
Fill out a report on http://egems.med.ge.com/edq/home.jsp
Contact the local service coordinator.
g
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE COMPONENT REPLACEMENT
REV 7 2326235
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Discard used batteries according to the manufacturer’s
instructions.
h
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 7 2326235
REVISION HISTORY
PAGE REV PAGE REV PAGE REV PAGE REV PAGE REV
Title page. . . . . . . . . 7 PM0102 . . . . . . . . . . 0 Tab 3 (GANTRY) Tab 5 (TABLE} PM0604. . . . . . . . . . 0
a to h . . . . . . . . . . . . 7 PM0103 . . . . . . . . . . 0 PM0605. . . . . . . . . . 0
PM0301 ..........1 PM0501 . . . . . . . . . . 0
A ............... 7 PM0104 . . . . . . . . . . 0 PM0606. . . . . . . . . . 0
PM0302 ..........0 PM0502 . . . . . . . . . . 0
B . . . . . . . . . . . . blank PM0105 . . . . . . . . . . 0 PM0303 ..........0 PM0607. . . . . . . . . . 0
PM0503 . . . . . . . . . . 0
Contents . . . . . . . . . 6 PM0106 . . . . . . . . . . 0
PM0304 ..........0 PM0504 . . . . . . . . . . 0
PM0107 . . . . . . . . . . 0
PM0305 ..........0 PM0505 . . . . . . . . . . 0
PM0108 . . . . . . . . . . 0 Tab 7 (PDU)
PM0306 ..........0 PM0506 . . . . . . . . . . 0
General PM0109 . . . . . . . . . . 5
PM0307 ..........3 PM0507 . . . . . . . . . . 2 PM0701. . . . . . . . . . 0
General . . . . . . . . . 0 PM0110 . . . . . . . . . . 0 PM0702. . . . . . . . . . 0
PM0308 ..........0 PM0508 . . . . . . . . . . 0
PM0309 ..........0 PM0509 . . . . . . . . . . 0 PM0703. . . . . . . . . . 0
Schedule . . . . . . . . . 7 PM0510 . . . . . . . . . . 0
Tab 2 (OPERATOR
PM0511. . . . . . . . . . . 0 Tab 8 (MOD)
PM Report . . . . . . . 6 CONSOLE) Tab 4 (DAS/DETEC- PM0801. . . . . . . . . . 0
PM0201 . . . . . . . . . . 0 TOR)
PM0202 . . . . . . . . . . 0 Tab 6 (X-RAY GEN-
PM0401 ..........0 Blank/Rear cover. . . . -
PM0203 . . . . . . . . . . 0 PM0402 ..........0 ERATOR)
PM Procedure PM0204 . . . . . . . . . . 0
PM0403 ..........0 PM0601 . . . . . . . . . . 0
PM0205 . . . . . . . . . . 0
Tab 1 (System) PM0404 ..........6 PM0602 . . . . . . . . . . 0
PM0206 . . . . . . . . . . 0
PM0603 . . . . . . . . . . 0
PM0101. . . . . . . . . . 0
A
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
B
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 6 2326235
CONTENTS
GENERAL
Introduction
Tools
CT PM Schedule
CT PM Report
CT PM PROCEDURE
System
PM0101 Verify Emergency OFF buttons (Gantry/Console/PDU)
PM0102 Check X-ray ON lights or buzzer / Operation of scan abort
PM0103 Caution Label Check
PM0104 Image Check (Image Performance)
PM0105 Check Error Logs
PM0106 Perform Filter Curve Test
PM0107 Check Ground Cable Terminals
PM0108 Check DAS Count
PM0109A Mage Performance
PM0109B Tube Gas Bubble Inspection
PM0110 Phantom Check
Console
PM0201 Verify Audio Function
PM0202 Clean Air Filter
PM0203 Inspect FANs
PM0204 Verify Mouse for smooth operation
PM0205 Clean Display monitor / Console exterior
PM0206 Check Cables / Power Cable Terminals
Gantry
PM0301 Check the number of Gantry revolutions
PM0302 Clean Mylar ring cover
PM0303 Verify Cables and Hardware are tight
PM0304 Gantry Cover Cleaning
PM0305 Check Positioning Light
PM0306 Check Gantry Anchor / Gantry Isolation
PM0307 Main bearing grease-up
PM0308 Check Drive Belt for wear
PM0309 Check RF Shoe Position
i
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 6 2326235
CONTENTS
CT PM PROCEDURE (CONTINUED)
DAS/Detector
PM0401 Check/Clean Detector face
PM0402 Verify Detector heater control
PM0403 Inspect Fans
PM0404 Inspect DAS Base
Table
PM0501 Check Head Holder
PM0502 Check Table Cover
PM0503 Gap between Table Cover and Cradle
PM0504 Check Cradle Rail
PM0505 Holder Stability Check
PM0506 Check Touch Sensor operation
PM0507 Verify Unlatch Function
PM0508 Check Gantry / Table interlock
PM0509 Clean Cradle tray / Table Cover
PM0510 Check for Oil Leak
PM0511 Check Table anchors / Table Isolation
XG
PM0601 Check / Clean Radiator FAN
PM0602 Check X-ray tube oil and HV connector
PM0603 Check HV Tank and HV connector
PM0604 Check Power Cable connection
PM0605 Check Tube overheat safety
PM0606 Check KV and mA
PM0607 Check Parts
PDU
PM0701 Inspect FANs (200V PDU only)
PM0702 Check Power Cable Terminals
PM0703 Check Power Line Voltage
MOD
PM0801 Dry Cleaning
ii
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
GENERAL
INTRODUCTION
BEFORE STARTING A PERIODIC MAINTENANCE, READ THE SAFETY GUIDELINES MANUAL THOROUGHLY
TO PREVENT EQUIPMENT DAMAGE, PERSONAL HARM, HARM TO OTHERS OR DEATH DURING SERVICE.
Recommended PM frequency is 2 times a year for CT/e Dual, ProSpeed AII/FII series scanners. The frequency may
vary due to local ordinance and the usage of the system, the system availability etc. If you need more PMs, order
extra copies of this document or copy the schedules.
TOOLS
GENERAL TOOLS
x Service Manuals
x Socket Head Wrench Set
x Torque Wrench
x Protractor
x Oscilloscope
x Digital Multimeter
x Grease-2188551 (Shell Alvania #2 or equivalent)
x Alcohol (ethyl alcohol-no water addition, or isopropyl disinfectant alcohol)
x CRC or equivalent (WD40, etc...)
x Cloth
x Kim Wipe or equivalent
x Soft tissue
x Glass Cleaner
x Dust Bag
x HEPA Vacuum Cleaner
x MOD Cleaner kit
x Film Holder, Developer, and type52 Polaroid Film (For X-ray alignment, adjustment, not used in the PM)
SPECIAL TOOLS
x HV Divider, HV Cables, and Wrench for HV Cable
x Silicone Oil
x Resurfacer (P9183SU)
x Flexible Abrasive (P9183SV)
x Grease Gun
1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
blank 2326235
2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 7 2326235
SCHEDULE
Recommended PM frequency is 2 times a year for CT/e Dual, ProSpeed AII/FII series scanners. The frequency may
vary due to local ordinance and the usage of the system, the system availability etc. If you need more PMs, order
extra copies of this document or copy the schedules.
Priority Code
Pr (Priority) - Description
1 Safety and Regulatory
2 Image Quality
3 Procedures that make the system unavailable for scanning
4 Procedures that can be performed while the customer is scanning
Frequency Code
Fr (Frequency) - Description
S Semi-Annually (every 6 months)
A Annually (every 12 months)
1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 7 2326235
SCHEDULE (CONTINUED)
Image Quality
2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 7 2326235
SCHEDULE (CONTINUED)
System Performance
*1:Option
3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 6 2326235
Schedule A/B
Site : Date:
System ID : Dispatch No. :
Check Item Result
Safety and Regulatory
System Verify Emergency OFF buttons (Gantry/Console/PDU)
Check X-ray ON lights or buzzer / Operation of scan abort
Caution Label Check
Check Error Logs
Gantry Check the number of Gantry revolutions
Console Verify Audio Function
Table Check Head Holder
Check Table Cover
Gap between Table Cover and Cradle
Check Cradle Rail
Holder Stability Check
Check Touch Sensor operation
Verify Unlatch Function
Check Gantry / Table interlock
XG Check Parts
Image Quality
System Image Check (Image Performance)
Gantry Clean Mylar ring cover
DAS/Detector Check/Clean Detector face
Comment:
i
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 6 2326235
Schedule A
Comment:
ii
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 6 2326235
Schedule B
Comment:
iii
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
blank 2326235
iv
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Press an emergency OFF switch on the Gantry front panel and verify that the power for Table/Gantry (Servo
Amp, Gantry control, and Table/Tilt) is removed.
2. Turn the power switch of the Operator Console OFF, then ON again. Verify that all systems, including Table/
Gantry, are turned ON.
3. Repeat this check for all the other emergency switches on the Gantry(six in all), PDU, and Operator Console
(See illustration below).
1-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
Emergency Switches
1-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
CAUTION
Do not enter scan room unprotected when x-rays are present.
1. Check the X-ray ON lights and X-ray buzzer for the following :
a. Perform an axial scan.
b. Verify that the X-ray buzzer is heard during X-ray exposure.
c. Verify that the X-ray ON lights illuminates on the keyboard and Gantry front panel.
d. Verify that the X-ray room (Gantry room) warning lights connected to the system are operating normally.
2. Check the operating of scan abort for the following :
a. Perform an axial scan.
b. Press the Abort switch on the Operator Console while performing a scan and verify that X-ray exposure is
terminated.
1-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Every caution label is securely attached to the Gantry front, Table front end, and Console.
If they have come off, replace them (See illustration below)
Caution Label
1-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Set the water phantom to the phantom holder.
2. Perform axial scans and verify that the image has no artifact.
3. Verify that the water CT number and air CT number equal 0 3 and -1000 5 respectively.
4. If the means and standard deviations are out of specifications, or artifacts are present, schedule time to look
into possible problems.
1-5
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Service Lines : Specific and detailed information concerning the error including (but not limited to) : --Additional
problem descriptions cause information. Information indicating what was supposed to happen, what did happen, and
how it was detected (for example, expected value vs. actual value, name of file attempted to open, etc.). This
includes any information concerning abnormal conditions related to the error.
Note
Refer to ERROR CODE AND MESSAGE LIST in the SYSTEM tab of the DIAGNOSTICS Manual.
1-6
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Note
Refer to BOW-TIE FILTER CURVE TEST in the GANTRY tab of the FUNCTIONAL CHECK /
ADJUSTMENT Manual.
6. Check the filter curve using VIEW VECTOR. (Check that the curve is smooth)
7. Visually check the filter for discoloration or cracks.
Replace if necessary.
1-7
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Inspect that all the ground cables are securely connected on terminals.
1-8
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Note
Refer to DAS COUNT CHECK in the X-RAY GENERATOR tab of the FUNCTIONAL CHECK /
ADJUSTMENT Manual.
This check verifies that the x-ray tube dose falls within specifications by checking DAS Counts.
This check should be performed when the x-ray tube is replaced.
1. Perform an axial scan.
AXIAL SCAN
SCAN TIME :3.0 sec
THICKNESS :10 mm
FOCUS :LARGE
KV :120 KV
mA :60 mA
SERIES NO. :1
(Others) :(defaults)
1-9
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Perform Image Performance Check.
Note
Refer to the following items in the SYSTEM tab of the FUNCTIONAL CHECK / ADJUSTMENT
Manual.
x General
x Image Performance
x Quality Assurance
1-10
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Perform Image Performance Check.
Under some circumstance, gas bubble in the tube will cause tube warm up error and it will also lead to image
artifact. Following is some illustrations of artifact.
Streaks
Streak
Smudge
1-11
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
2. To prevent image artifacts as above and notice bubbles when small, perform Sinogram to further confirm Tube
gas bubble.
a. Go to Service -> Diagnostics, perform an offline air scan.
AXIAL SCAN
KV: 140KV
mA: 60mA
Scan FOV: 43cm
(Others): (default)
b. Go to Service -> Diagnostics -> Scan Analysis, select just finished offline scan exam, press Plot VVC.
1-12
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
d. Select Channel from Region of Interest, press Plot Now. A normal plot will look clear as below (channel
343).
1-13
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
e. Following picture will appear on the screen, channel 343 when normal will look level as below.
Note
If shadow or white band exists, make sure to select appropriate channel so that the channel could
across shadow or white band.
f. Analysis: If shadow (white band) appears in Sinogram (as shown in following three figures), it means that
there is a high probability that gas bubble exist in tube. When small, bands may not cover all views or look
like streaks across the VVC.
Note
sometimes there is no problem for some air scan data, it is also possible for existing bubble, just
doesn't affect that special scan.
1-14
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
1-15
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
3. Take off tube for further inspection (see component replacement manual for detailed procedures), check tube
port and anode end fill plug for gas bubble.
4. Inform Customer.
If gas bubble is confirmed through above inspection, advise customer to order new tube for replacement
because it may lead to image artifact.
1-16
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Verify visually that phantoms are intact from any damage or scratches which affect the use.
1-17
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
1-18
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that the Operator can properly hear sounds in the Scan room through the speaker.
2. Verify that the voice of the Operator can be properly heard in the Scan room through the microphone while
stepping on the foot switch.
3. If necessary, adjust the intercom volumes on the Operator Console (Refer to the CD-ROM manual, Functional
Check & Adjustment, Operator Console).
Note
In case sound from the scan room is noisy, replace the microphone in the Gantry.
2-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• Vacuum Cleaner
PREREQUISITES
• None
TASK DESCRIPTION
1. Clean each air filter of the Operator Console using a vacuum cleaner
Air Filters
2-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that the power to the Operator Console is OFF.
2. Remove the Operator Console Front cover.
3. Turn ON power to the Operator Console.
4. Using a flashlight, or by feeling for the proper airflow, check that the FAN is operating normally.
(See illustration 2-2)
5. FANs should also be free of dirt and should operate quietly.
If any FAN is defective, replace the unit.
2-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
FANs
Right Side View
FANs FANs
OC Front View
Rear View
2-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that the power to the Operator Console is ON.
2. Check that the mouse operate smoothly in all directions, without jittering.
3. Display the cursor on the monitor.
4. Verify that the mouse movement is smooth.
If not smooth, clean 2 shafts on the mouse unit with alcohol and cotton swab
2-5
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that the power to the Operator Console is OFF.
2. Clean the CRT screen using Glass Cleaner, etc.
Clean also the exterior of the console, including the keyboard.
2-6
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that the power to the Operator Console is OFF.
2. Remove the Operator Console rear cover.
3. Verify that all the cables within the Operator Console are properly installed/secured.
In particular, inspect well the 5V P/S cables where they connect to the +5V power bar. These must not be loose.
4. Switch OFF the Operator Console power breakers.
5. Verify that the power cables (AC 115 V) are securely connected on terminals within the Operator Console.
Power Cables
OC Rear View
2-7
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
2-8
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Note
Refer to SLIP RINGS AND BRUSHES in the GANTRY tab of the FUNCTIONAL CHECK /
ADJUSTMENT Manual.
4. END
3-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
CAUTION
Use proper procedures to avoid blood-borne pathogens.
The maintenace tasks which follow include procedures concerned with the cleaning of
equipment (Table Tray, Gantry Cover, etc.). Refer to local/company guidelines for those
procedures, especially where body fluids or other possible contaminates are present.
2. END
3-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Understand and follow the Safety Guidelines Manual.
1. Set the Gantry to the 0_ tilt position and lower the table to its lowest position.
2. Switch OFF the “Rotate”, “XG Power” and “Table/Tilt” switches at the Gantry rear base.
3. Remove the front, right side, and left maintenance covers.
4. Switch ON the service switch on the SUB board near the TGP board.
5. Rotate the gantry in the CW direction by hand and make sure all cables, harness, and other hardware are firmly
attached.
Note
If any components are loose, tighten it to the specified torque.
Refer to TORQUE VALUE FOR SCREW TIGHTENING in the INTRODUCTION tab of the
FUNCTIONAL CHECK / ADJUSTMENT Manual.
6. END
3-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Understand and follow the Safety Guidelines Manual.
1. Clean Gantry covers.
CAUTION
Use proper procedures to avoid blood-borne pathogens.
The maintenace tasks which follow include procedures concerned with the cleaning of
equipment (Table Tray, Gantry Cover, etc.). Refer to local/company guidelines for those
procedures, especially where body fluids or other possible contaminates are present.
CAUTION
Do not look directly into the laser behind the alignment light window. The laser can cause
eye damage.
NOTICE
Do not attach cleaning detergent around Microphone.
NOTICE
AVOID EQUIPMENT DAMAGE!
Do not bend or deform the film of the alignment light window.
3-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
CAUTION
Damage to visual function !!
Never look directly into the positioning lights. The lights can severely harm the eyes.
5. END
3-5
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Understand and follow the Safety Guidelines Manual.
1. Inspection that the Gantry is firmly anchored to the floor by four anchor bolts and that no cracks exist on the
insulating plate for each anchor bolt.
2. Verify that the Gantry is in no contact with the floor. If not, adjust feet for isolation.
3. END
3-6
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• Grease Gun (U0018BF)
• Grease Cartridge : Shell Alvania Grease #2 (2188551)
NOTICE
To ensure the quality of the lubricant, please order the lubricant from GPO. Otherwise,
unqualified lubricant may cause damage to bearing.
PREREQUISITES
• None
TASK DESCRIPTION
Understand and follow the Safety Guidelines Manual.
1. Switch OFF the “Rotate” and “XG Power” switches at the Gantry rear base.
2. Remove the rear, right side, and left maintenance covers.
3. Switch ON the service switch on the SUB board near the TGP board.
Note
New grease must be used. Do NOT reuse a grease cartridge; open a brand new grease cartridge
every time you perform this operation.
4. Input the grease(SHELL ALVANIA grease #2) into the grease gun.
Gantry Frame
Hose
Grease Nipple
3-7
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
5. Attach the grease gun to the bearing grease nipple (see illustration 3-2).
6. Inject the grease (one cartridge) while rotating the Gantry slowly by hand. Any grease which leaks between the
shaft of main bearing and housing must be wiped clean.
NOTICE
Slow pumping operation is required. If pumped fast, new grease will be soon ejected so that
new grease can NOT reach the main bearing.
15. END
3-8
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
6. END
3-9
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 5 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
Note
Refer to RF SHOE POSITION in the GANTRY tab of the FUNCTIONAL CHECK / ADJUSTMENT
Manual.
5. END
3-10
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
5. END
4-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
7. END
4-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
6. END
4-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
FANs
4-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 6 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
6. If any crack exists on the DAS Base, please order the DAS Base service kit (5257583) to replace it.
7. END
4-5
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
Blank
4-6
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Check each head holder on site for the following:
• The latch hook stops at each of the lock and release positions.
• The hook axis has not become weak.
• No cracks exist on the acrylic resin parts; especially inspect well the rib root (where the patient’s neck is
placed), and parts around the flat head screws.
If any crack is found, replace the head holder.
• No flat head screws are loose. If loosened, tighten those. (Torque: 8 kg-cm; turn the grip of the
screwdriver using thumb, index finger, and middle finger, which gives approximately this torque.)
Tighten the loosened screws only, and DO NOT excessively tighten the screws, which will cause cracks.
• All velcro tape is securely attached to the head holders. If not the case, replace the velcro tape.
• Check that the lock hook is securely attached to each head holder.
If not, tighten the loosened flat head screw. Do not over tighten screws.
• Repeat the same check for the cradle side lock hook.
5-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Check that the Table Cover is not deformed and not damaged. Also check that the Table Cover does not
interfere with the cradle.
5-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Check that the position of the table cover and the cradle are parallel, and the gap between them is 7mm or less.
Note
Refer to PARALLEL SETTING OF CRADLE in the TABLE tab of the FUNCTIONAL CHECK /
ADJUSTMENT Manual.
5-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Check the cradle for the following
• Check that the Velcro tape of the cradle is securely attached. If the Velcro tape has come off, replace
the cradle.
• Check that the attachment rails are not damaged or cracked. If damaged, replace them.
• Check that the cradle rails are not damaged or cracked. If damaged, replace the cradle as an assembly.
• Set the body strap to the attachment rails, then pull the strap by the force of approx. 15 kgf, using a spring
balance. Verify that the strap do NOT be removed from the rail. If not, replace the strap, attachment rails
or cradle.
5-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
Velcro Tapes
Cradle
Attachment Rails
(Both Side)
Cradle Rails
Body Strap
Attachment Rail
Cradle
5-5
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that the following holders is not loose by hand, when they are attached to the cradle edge.
• Axial Head Holder
• Cradle Extender
• Head Holder
• Phantom Holder
• Coronal Holder
• None
5-6
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Press the Touch Sensor during the Table DOWN operation, and verify that the Table DOWN movement stops.
Repeat this for all touch sensors.
Note
To resume the Table down motion, first move the Table slightly UP, then perform the Table DOWN
operation.
5-7
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Move the cradle “IN” by 500mm from out limit.
2. Push the Latch SW.
3. Verify that cradle position LED on the Gantry display is off, and cradle does not move “IN” when cradle “IN” SW
is pressed.
4. Push the Latch SW again.
5. Verify that cradle posiion LED on the Gantry display is on, and cradle does move “IN” when cradle “IN” SW is
pressed.
6. Repeat the same check for the opposite unlatch switch.
5-8
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Raise the Table to the highest position.
2. Tilt the Gantry to the 0 deg. position.
3. Move the cradle to an position except the out limit position.
4. Move the Table down until it stops automatically ; this is the interlock position, but that the cradle in/out function
can still operate.
5. Move the cradle to the out limit position.
6. Verify that the Table can be lowered to the lowest position.
7. Repeat steps 1. through 3. with other tilt angles.
5-9
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• Vacuum Cleaner
PREREQUISITES
• None
TASK DESCRIPTION
1. Clean Table covers, cradle and foot switches.
CAUTION
Use proper procedures to avoid blood-borne pathogens.
The maintenace tasks which follow include procedures concerned with the cleaning of
equipment (Table Tray, Gantry Cover, etc.). Refer to local/company guidelines for those
procedures, especially where body fluids or other possible contaminates are present.
NOTICE
AVOID EQUIPMENT DAMAGE!
Do not use chloric detergent.
a. Clean dust from the Table top cover (tray) using a vacuum cleaner.
b. Clean the Table covers.
c. Use a cloth and a mild detergent or alcohol to clean the covers and the foot switches.
5-10
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Verify that no oil has leaked from the cylinder, pump, hoses, etc. Verify that the Table does not lower on its
own when the Table is left unoperated for some time.
5-11
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 2 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
1. Inspect that the Table is firmly anchored to the floor, by four bolts and that no cracks exist on the insulating
plate for each anchor bolt.
Note
If any anchor bolts are loose, tighten it to the specified torque.
Anchor Nut
Gantry Base
Floor Floor
105mm or more
12mm
2. Verify that the Table is in no contact with the floor. If not, adjust feet for isolation.
5-12
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• Vacuum Cleaner
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
4. END
6-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
CAUTION
Shock hazard.
Wait more than five minutes following the last scan before performing the following
procedure.
8. END
6-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
CAUTION
Shock hazard.
Wait more than five minutes following the last scan before performing the following
procedure.
8. END
6-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
CAUTION
Shock hazard.
Wait more than five minutes following the last scan before performing the following
procedure.
7. END
6-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ROTATION HAZARD!
WHEN YOU PRESS THE ‘POSN LIGHT’ BUTTONS (LARGE BUTTON AND SMALL BUTTON),
THE GANTRY QUICKLY ROTATES TO THE -14 DEG. POSITION. IF IT IS NECESSARY TO
PLACE ANY PART OF YOUR BODY INSIDE OR NEAR THE GANTRY, SWITCH OFF THE
‘ROTATE’ SWITCH FIRST.
7. END
6-5
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Understand and follow the Safety Guidelines Manual.
1. Preparation:
a. Remove the left maintenance cover from the Gantry.
b. Set the 42 cm Polypropylene Phantom to the phantom holder.
c. Move the cradle to position the phantom at the Detector window.
(This is to protect the Detector by reducing x-ray dose to it during the check procedure)
d. Perform Warm-up scans, if the x-ray tube is cold.
e. Wait five minutes or more following the last scan prior to proceeding to the next step.
2. Set the M5 Management dip switch to ON on the TGP Board.
(KV & MA display mode on Gantry Display)
3. Perform scans of KV - MA stations specified in Table 2-1.
Select 1 mm or any THICKNESS to allow the specified stations.
Verify that the KV and MA values displayed on the Gantry Display is within the following specifications:
KV:r5 kV
MA:r20 mA
(KV and MA values are displayed in real-time during an exposure, and ‘0’ is displayed after the exposure is
finished)
4. Set the M5 Management dip switch to OFF on the TGP Board.
5. END
TIME FOCUS KV mA
120 60 100 160 200
1.5 sec Large
140 60 130 160 -
Other scan parameters: defaults
6-6
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
Understand and follow the Safety Guidelines Manual.
2. Battery replacement
3. Download database
6-7
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
6-8
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ELECTRIC SHOCK HAZARD !!
DANGEROUS VOLTAGES EXIST WITHIN THE UNIT, USE EXTREME CARE TO AVOID
INJURY TO PERSONNEL AND EQUIPMENT.
2. END
7-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ELECTRIC SHOCK HAZARD !!
DANGEROUS VOLTAGES EXIST WITHIN THE UNIT, USE EXTREME CARE TO AVOID
INJURY TO PERSONNEL AND EQUIPMENT.
CAUTION
Leave all power to the system OFF and tagged until power is called for in specific steps.
3. END
7-2
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• None
PREREQUISITES
• None
TASK DESCRIPTION
WARNING
ELECTRIC SHOCK HAZARD !!
DANGEROUS VOLTAGES EXIST WITHIN THE UNIT, USE EXTREME CARE TO AVOID
INJURY TO PERSONNEL AND EQUIPMENT.
2. END
7-3
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
7-4
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
REV 0 2326235
SPECIAL TOOLS/SUPPLIES
• Head Cleaning Kit (U0060ZA: 2148392)
PREREQUISITES
• None
TASK DESCRIPTION
Dry Cleaning
Note
Instruct the user to perform this procedure once per every 6 months.
Keep the Cleaning Tool in place that is free from dust and any external force.
8-1
CT/e Dual, ProSpeed AII/FII Series
GE HEALTHCARE PERIODIC MAINTENANCE
8-2
www.gehealthcare.com
Imagination at work