Professional Documents
Culture Documents
0
Database version
2023.3.28.8.8
Date
27/05/2023
fischer FZE
Enquiry@fischer.ae
www.fischer.ae
Design Specifications
Anchor
Anchor system fischer Injection system FIS EM plus
Injection resin FIS EM Plus 390 S
Fixing element Threaded rod FIS A M 24 x 450 8.8,
zinc plated steel, Property Class 8.8
Calculated anchorage 260 mm
depth
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 1
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Input data
Design actions *⁾
# NSd VSd,x VSd,y MSd,x MSd,y MT,Sd Type of loading
kN kN kN kNm kNm kNm
1 7.00 18.00 18.00 0.00 55.00 0.00 Permanent-Transient/Static
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 2
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Steel failure
( NRd,s )
βN,s
Anchor no. % Group N° Decisive Beta
1 39.6 1 βN,s;1
2 0.0 2 βN,s;2
3 39.6 3 βN,s;3
4 0.0 4 βN,s;4
5 39.6 5 βN,s;5
6 0.0 6 βN,s;6
( NRd,p )
Eq. (5.2)
Eq. (5.2a)
Eq. (7.14a)
Eq. (7.15)
Eq. (7.16)
Eq. (5.2e)
Eq. (5.2f)
Eq. (5.2g)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 3
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Eq. (5.2h)
Eq. (5.2i)
βN,p
Anchor no. % Group N° Decisive Beta
1, 3, 5 74.4 1 βN,p;1
( NRd,c )
Eq. (5.3)
Eq. (5.3a)
Eq. (5.3c)
Eq. (5.3d)
Eq. (5.3e)
βN,c
Anchor no. % Group N° Decisive Beta
1, 3, 5 80.8 1 βN,c;1
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 4
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
( VRd,s )
Eq. (5.6/a)
βVs
Anchor no. % Group N° Decisive Beta
1 31.9 1 βVs;1
2 31.2 2 βVs;2
3 31.9 3 βVs;3
4 31.2 4 βVs;4
5 31.9 5 βVs;5
6 31.2 6 βVs;6
( VRd,cp )
Eq. (5.7a)
Eq. (5.3)
Eq. (5.3a)
Eq. (5.3c)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 5
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Eq. (5.3d)
Eq. (5.3e)
βV,cp
Anchor no. % Group N° Decisive Beta
1, 2, 3, 4, 5, 6 3.5 1 βV,cp;1
Eq. (5.9b)
Eq. (5.10)
Eq. (5.9b)
Eq. (5.9c)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 6
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Technical remarks
All data and information in the software is based on fischer products and common engineering knowledge. Please
check all the proof results against local valid standards and approvals.
As fischer is not the design office, the attached is no guarantee for incorrect input or assumptions. Any
recommendations have to be approved by the building-authority or project engineer. Results are valid only for
anchor system calculated in the attached. If any part of the system is changed, it will invalidate this report and new
calculations would be required.
The transmission of the anchor loads to the supports of the concrete member shall be shown for the ultimate limit state and
the serviceability limit state; for this purpose, the normal verifications shall be carried out under due consideration of the
actions introduced by the anchors. For these verifications the additional provisions given in the current design method shall
be taken into account.
As a pre-condition the anchor plate is assumed to be flat when subjected to the actions. Therefore, the plate (if present) must
be sufficiently stiff. The C-Fix anchor plate design is based on a proof of stresses and does not allow a statement about the
stiffness of the plate. The proof of the necessary stiffness is not carried out by C-Fix.
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 7
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Installation data
Anchor
Anchor system fischer Injection system FIS EM
plus
Injection resin FIS EM Plus 390 S (other cartridge Art.-No. 544154
sizes available)
Fixing element Threaded rod FIS A M 24 x 450 8.8, Art.-No. 558867
zinc plated steel, Property Class 8.8
Installation details
Thread diameter M 24
Drill hole diameter d0 = 28 mm
Drill hole depth h1 = 260 mm
Calculated anchorage hef = 260 mm
depth
Drilling method Hammer drilling
Drill hole cleaning 2 times blowing (compressed air),
2 times brushing,
2 times blowing (compressed air)
No borehole cleaning required in
case of using a hollow drill bit, e.g.
fischer FHD.
Installation type Pre-positioned installation
Annular gap Annular gap not filled
Maximum torque Tinst,max = 150.0 Nm
Socket size 36 mm
Base plate thickness t = 30 mm
Stand-off distance g ≤ 50 mm
Total fixing thickness tfix ≤ 80 mm
Tfix,max
Volume of resin per drill 76 ml/38 scale divisions
hole
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 8
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
Attachment
Profile type Rectangular hollow tube
cold formed (250x150x8)
Anchor coordinates
x y
Anchor no. mm mm
1 -125 180
2 125 180
3 -125 0
4 125 0
5 -125 -180
6 125 -180
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 9
C-FIX 1.115.0.0
Database version
2023.3.28.8.8
Date
27/05/2023
ENSO-Datasheet
Anchor
Injection resin FIS EM Plus 390 S
Fixing element Threaded rod FIS A M 24 x 450 8.8,
zinc plated steel, Property Class 8.8
Characteristic resistances 1)
Characteristic resistance for steel failure under tension
Characteristic resistance 8.8 NRk,s kN 282.00
Partial safety factor γMs,N - 1.50
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 10