Professional Documents
Culture Documents
Training
(155mm x 70mm)
Agenda
• ทฤษฎีและหลักการ การสื่อสารทางแสง
• ประวัติและความเป็ นมา
• ทฤษฎีและหลักการ การใช้ เครื่ องมือวัด
• Optical Time domain Reflectometer (OTDR)
• Power Meter and Light Source
• Fusion Splicer
• การฝึ กใช้ งาน (Hand On Practice)
• ถามตอบ และ ทดสอบ
การส่งสัญญาณผ่าน Optical Fiber
Link Loss =
(Fiber Length (Km) x Fiber Attenuation per Km) + (Splice Loss
x Number of Splice) + (Connector Loss x Number of Connector)
การสื่ อสารผ่าน Optical Fiber
Fiber Attenuation
การสื่ อสารผ่าน Optical Fiber
การสื่ อสารผ่าน Optical Fiber
การสื่ อสารผ่าน Optical Fiber
ชนิดของหัว
Connector
การสื่ อสารผ่าน Optical Fiber
Fiber Standard Specification
Single Mode Fiber Standard Specification
หลักการทํางานของเครื่ องมือทดสอบ ทางแสง
Optical Time Domain Reflectometer (OTDR)
เครื่ องมือทดสอบ OTDR
สามารถตรวจวัดความยาวของเส้ นใยนําแสง
1. สามารถตรวจวัดความยาวของเส้ น Optical Fiber
2. สามารถตรวจวัดค่าการลดทอนกําลังของแสงภายใน Optical Fiber
a. การลดทอนกําลังของแสงรวมตลอดทังเส้ ้ นหรื อต่อหน่วยความยาว (dB / Km)
b. การลดทอนกําลังของแสงที่แต่ละตําแหน่ง
3. สามารถตรวจวัดค่าการสูญเสียของแสง เนื่องจากการเชื่อมต่อ (Splice and Connector loss)
4. สามารถแสดงถึงตําแหน่งที่มีการติดตังที
้ ่ไม่ถกู ต้ องเช่นมีการ โค้ งงอสายมากเกินไป
5. สามารถบอกระยะทางที่วดั ได้ ในแต่ละตําแหน่งเพื่อตรวจสอบและค้ นหาตําแหน่งที่มีปัญหา
ภายในสาย Fiber Optic อย่างแม่นยํา
หลักการทํางานของ OTDR
Optical Time Domain Reflectometer (OTDR)
หลักการทํางานของ OTDR
หลักการทํางานของ OTDR
ค่าพารามิเตอร์ของ OTDR
• ค่า Dynamic Range และ ค่า Signal to Noise Ratio
• ค่า Resolution และ ค่า Plus Width
• ค่า Number of Average
• ค่า Dead Zone
– Event Dead Zone (Back Scattering)
– Attenuator Dead Zone (Rayleigh Scattering)
• ค่า Loss Event
– Reflective Event (Connector Loss)
– Non-Reflective Event (Splice Loss, Micro bending)
• ค่า Index of Reflectometer (IOR)
การแสดงผล OTDR
Y = −{10logR + 10log(10X/5−1)}
where R is a variable determined by the currently set pulse width and
other such factors
การแสดงผล OTDR
การแสดงผล OTDR
การแสดงผล OTDR
การแสดงผล OTDR
การแสดงผล OTDR
การแสดงผล OTDR
การแสดงผล OTDR
การแสดงผล Dynamic Range
การแสดงผล OTDR
การตังค่
้ า Resolution
Typically begin with the lowest resolution (highest number) possible.
Pros - much faster acquisition time, smaller trace file size
Cons - minimal degradation in accuracy of measurements
การแสดงผล OTDR
การตังค่
้ า Pulse Width
การแสดงผล OTDR
การตังค่
้ า Pulse Width
การแสดงผล OTDR
การตังค่
้ า Averaging
การแสดงผล OTDR
OTDR Hand on Practice
OTDR Hand on Practice
OTDR Hand on Practice
เครื่ องกําเนิดแสง Optical Light source
Training
เครื่ องกําเนิดแสง Optical Light source
• เครื่ องทดสอบ ค่า Loss ในสาย Optical Fiber อย่างง่าย
• เครื่ องกําลังแสง ( Optical Power Meter ) เป็ นเครื่ องวัดระดับกําลังแสงในหน่วยวัตต์
(w) หรื อ dBm ใช้ สําหรับวัดกําลังแสงของทางด้ านแสงเช่นความแรงของสัญญาณ
ไดโอดเปล่งแสงหรื อ เลเซอร์ ไดโอด รวมถึงใช้ ตรวจสอบโมดูลของภาคสงสัญญาณและ
วงจรขับ (Line Driver)
• เครื่ องวัดกําลังแสง จะประกอบด้ วย Power Meter และตัวเซนเซอร์ ( Sensor ) โดยที่
ตัวเซนเซอร์ จะอยู่ภายในเครื่ อง (Built – in Sensor)
เครื่ องกําเนิดแสง Optical Light source
• เครื่ องกําเนิดแสง ( Stabilized Light Source ) เป็ นเครื่ องกําเนิดแสง ซึง่ อาจจะเป็ น
แหล่งกําเนิดแสง แอลอีดี ( LED Source ) หรื อ เลเซอร์ ( LD Source ) ก็ได้ ขึ ้นอยู่กบั
ความเหมาะสมในการใช้ งานจะถูกใช้ รวมกับ เครื่ องวัดกําลังแสง ( Optical Power
Meter ) ในการวัดการลดทอนของสัญญาณแสง
• (Attenuation Loss ) ของเคเบิลตลอดเส้ นทางจากต้ นทางถึงปลายทางหรื อที่เรี ยกว่า
Total Loss Stabilized Light Source ส่วนใหญ่จะประกอบด้ วย Main Frame และ
Plug – in Unit ซึง่ มีหลายวามยาวคลื่นให้ เลือกใช้ ตามความเหมาะสม
• อุปกรณ์นี ้สามารถใช้ ตรวจจับสัญญาณแสงได้ ทงั ้ แบบ CW (รวมถึงสัญญาณที่ใช้ สื่อสาร
ข้ อมูลจริ ง) และแบบ modulate ด้ วยความถี่ 270 Hz, 1 kHz และ 2 kHz
Optical Power Meter
CMA5 Series
Fiber Optic Power Meters
Course Training
Course Training Agenda
72
MARIGOLD TECHNOLOGIES CO.,LTD.
Specifications
Item Specification
Detector Type P-100/P-200: InGaAs
Range P-100/P-200: +10 dBm to –60 dBm, (+10 to –50 dBm @
850nm)
Calibrated Wavelengths 850, 1300, 1310, 1490, 1550, &1625nm
73
MARIGOLD TECHNOLOGIES CO.,LTD.
Specifications
Item Specification
Resolution 0.01 dB
dB Reference Yes
Modulation Detection 2KHz - visual indicator
Stability (8 Hours) ±0.1 dB
Display Indicators 4 digit, 7-segment LCD
Low Battery Indicator visual indicator
Auto Power-Off AUTO OFF - visual indicator
Battery Life (Alkaline) >40 hrs. continuous use
Connector Adapters CMA5/P-100 and CMA5/P-100C: FC, ST & SC
74
MARIGOLD TECHNOLOGIES CO.,LTD.
Specifications
Item Specification
Power One 9 Volt Alkaline battery
75
MARIGOLD TECHNOLOGIES CO.,LTD.
Operating Controls
76
MARIGOLD TECHNOLOGIES CO.,LTD.
Operating Controls
77
MARIGOLD TECHNOLOGIES CO.,LTD.
Measurement Description
1. Fiber Optic Input
The units are equipped with a universal connector. A variety of adapter
caps are available on FC, SC connecter
2. External AC Power Jack
Attach the optional AC Power adapter to this jack.
3. Measurements are displayed in:
• absolute power (dBm)
• relative loss (dB)
• microwatts (µµµµµW)
• define wavelength
• low battery ( AUTO OFF )
• REF (indicates stored reference value)
78
MARIGOLD TECHNOLOGIES CO.,LTD.
Measurement Description
4. Ext. Power
The External Power indicator lights up green when you are operating
the unit on the optional external AC adapter.
5. On/Off Key
Power the unit on by pressing this key.
6. Auto Off Key
This key enables the Auto Off function which will power down the
unit when no keys have been pressed for 5 minutes.
79
MARIGOLD TECHNOLOGIES CO.,LTD.
Measurement Description
7. λ (Wavelength) Key
Press this key to cycle through the calibrated wavelengths (850, 1300,
1310, 1490, 1550, and 1625 nm).
8. dBm/W Key
Press the dBm/W key to toggle the unit’s measurement mode between
dBm (absolute power) and µW (microwatts). Hold the key until
“HELD” is displayed (about 2 seconds) to switch to dB(relative
power).
80
MARIGOLD TECHNOLOGIES CO.,LTD.
Measurement Description
9. Zero Key
Press the Zero key to automatically zero the power meter. See “Auto
Zero”
10. Ref Key
Pressing the Ref key momentarily will display the current dBm
reference power level for approximately 2 seconds. Holding down the
REF key until “HELD” appears in the display (approximately 3
seconds) will store the current dBm reference level. Separate
reference values can be saved for each wavelength. These will be
retained when power is turned off.
81
MARIGOLD TECHNOLOGIES CO.,LTD.
Hand On Practice
1. ต่อสาย Patch Cord เข้ ากับ Output Connector ของเครื่ อง Fiber Optic Light Source และ Fiber
Optic Input ของเครื่ อง Fiber Optic Power Meter
2. ตังค่
้ าเครื่ อง Fiber Optic Light Source โดยตังค่
้ า Wavelength ที่ 1310 nm, และเลือกการ MOD
แบบ CW
3. ตังค่
้ าเครื่ อง Fiber Optic Power Meter โดยตังค่
้ า Wavelength ที่ 1310 nm
4. กดปุ่ ม On ทังสองเครื
้ ่ อง
5. กดปุ่ ม CW/ MOD เลือก 270Hz
6. Fiber Optic Power Meter จะแสดงค่า Reference Power ของสาย Fiber Optic
83
การทดลองที่ 1 การวัดค่า Reference Power ของสาย Optic Fiber
Patch Cord
85
การทดลองที่ 2 การวัดค่ า Loss ของสาย Fiber Optic
Fiber Under Test
Patch Cord