Professional Documents
Culture Documents
STRUCTURAL CALCULATIONS
PROJECT NO.: #2311155
CLIENT: Fluid Solutions
PROJECT INFORMATION
SCOPE OF WORK: Foundation design
BILLING ADDRESS:
ADDRESS:
CITY:
STATE:
ZIP:
COUNTRY:
SITE ADDRESS:
SEAL:
ADDRESS: 5098 Highway 411
CITY: Kingston
STATE: Georgia
ZIP: 30145
COUNTRY: USA
REVISION HISTORY
# DATE DESCRIPTION PREPARED BY CHECKED BY
01 12/12/2023 First Submital MH AG
02
03
REFERENCES: IBC 2018 amended, ASCE 7-16, ACI 318, ACI 360
Acceptance and use of this report by any party constitute a contractual agreement that the Engineers total liability arising out of or in any way related to this analysis and report
shall not exceed the total sum paid to the Engineer for the services provided. Liability does not exist beyond the analysis contained in this report.
S001V002
Copyright. Dotec Engineering
424 Jeffereson St., St. Charles, MO 63301. Phone: (636) 724-9872
1
CONTENTS
CONTENTS 2
LOADS 3
DESIGN 6
2
DOTec Corp.
Loads
D1 ≔ 72 ft
P1 ≔ π ⋅ D1 = 226.195 ft
π ⋅ D1 2
A1 ≔ ――― = ⎛⎝4.072 ⋅ 10 3 ⎞⎠ ft 2
4
D2 ≔ 75 ft
P2 ≔ π ⋅ D2 = 235.619 ft
π ⋅ D2 2
A2 ≔ ――― = ⎛⎝4.418 ⋅ 10 3 ⎞⎠ ft 2
4
3
DOTec Corp.
Dead Loads
Snow Loads
Snow ≔ 0
Fluid Loads
Wind Loads
3 ⋅ π ⋅ D1 2 Shell modulus
Sshell ≔ ―――― = ⎛⎝3.054 ⋅ 10 3 ⎞⎠ ft 2
16
4
DOTec Corp.
EQ Loads
17421 kip ⋅ ft ⎛
Nmax ≔ ――――― = ⎝5.705 ⋅ 10 3 ⎞⎠ plf Max. Vertical shell load
Sshell
π ⋅ D1 3
Sbase.inner ≔ ――― = ⎛⎝3.664 ⋅ 10 4 ⎞⎠ ft 3
32
26591.4 kip ⋅ ft
Pmax ≔ ―――――= 725.678 psf Max. Vertical Area load
Sbase.inner
Sds ≔ 0.3058
Sd1 ≔ 0.1705
Importance category = II
5
DOTec Corp.
1) Check piles for Ultimate Axial loads only based on Concrete capacity
D ≔ 18 in Lp ≔ 42 ft
6
DOTec Corp.
Ac ≔ Ag - As = 250.069 in 2
Po ≔ 0.8 ⋅ ⎛⎝0.85 ⋅ fc ⋅ Ag + fy ⋅ As⎞⎠ = 903.356 kip ϕPc ≔ ϕ ⋅ 0.8 ⋅ ⎛⎝0.85 ⋅ fc ⋅ Ag⎞⎠ = 380.686 kip
There is no tension
7
DOTec Corp.
3) Check piles for unfactored Axial loads based on Soil capacity in service
Pw ≔ 326 kip
8
DOTec Corp.
9
DOTec Corp.
Ph.n ⋅ 1 ft
Clearly from seeing the reactions and comparing them to ―――― = 13.5 kip The soil is
2
very safe from failure by lateral loads on pile
10
DOTec Corp.
Δ ≔ 0.141 in
Δall ≔ 0.5 in
11
DOTec Corp.
Mu ≔ 66.1 kip ⋅ ft
The pile will be checked for axial and bending using a Section design program
π ⋅ D3
S ≔ ――― = 572.555 in 3
32
‾‾‾‾
fc
Mcr ≔ S ⋅ 7.5 ⋅ ―― ⋅ psi = 22.632 kip ⋅ ft
psi
Lflex ≔ 11.1 ft
ψt ≔ 1 ψe ≔ 1 ψg ≔ 1
12
DOTec Corp.
fy ⋅ ψt ⋅ ψe ⋅ ψg
ld ≔ ―――――⋅ db = 28.46 in
25 ⋅ ‾‾fc ⋅ ‾‾‾ psi
⎛ 1 ⎞
Lreinf ≔ max ⎜Lflex + ld , 10 ft , ―⋅ Lp , 3 ⋅ D⎟ = 14 ft Reinforced length ACI318 Table 18.13.5.7.1
⎝ 3 ⎠
Vu ≔ 19.5 kip
be ≔ D ⋅ 0.88 = 15.84 in
3 3
d ≔ be - 3 in - ―in - ―in - 2 in = 10.09 in Approximately
8 8
Vc ≔ be ⋅ d ⋅ 2 ⋅ ‾‾
fc ⋅ ‾‾‾
psi = 20.217 kip
Try #3 @10"
Av ≔ 0.11 in 2 ⋅ 2 = 0.22 in 2
s ≔ 10 in
A v ⋅ fy ⋅ d
Vs ≔ ―――= 13.319 kip
s
Vn ≔ Vc + Vs = 33.535 kip
13
DOTec Corp.
Lp
―= 28
D
⎛ Lp ⎞
if ⎜― ≤ 30 , “Safe” , “UNSAFE”⎟ = “Safe”
⎝D ⎠
Standard hooks
fc
ψe ≔ 1 ψo ≔ 1 ψr ≔ 1.6 ψc ≔ ―――― + 0.6 = 0.863
105 MPa
fy ⋅ ψe ⋅ ψo ⋅ ψr ⋅ ψc db 1.5
Ldh ⎛⎝db⎞⎠ ≔ ―――――― ⋅ ―――
23 ⋅ ‾‾‾‾‾‾‾
fc ⋅ MPa mm 0.5
⎛6 ⎞
Ldh ⎜―in ⎟ = 15.475 in
⎝8 ⎠
14
P (kip)
1200
y
x
(Pmax)
18 in diam.
Units: English
-400
STRUCTUREPOINT - spColumn v6.00 (TM). Licensed to: Moaaz, Moaaz. License ID: -208B1
15
spColumn v6.00
Computer program for the Strength Design of Reinforced Concrete Sections
Copyright - 1988-2023, STRUCTUREPOINT, LLC.
All rights reserved
y
x
Licensee stated below acknowledges that STRUCTUREPOINT (SP) is not and cannot be responsible for either the accuracy or adequacy of the material
supplied as input for processing by the spColumn computer program. Furthermore, STRUCTUREPOINT neither makes any warranty expressed nor implied
with respect to the correctness of the output prepared by the spColumn program. Although STRUCTUREPOINT has endeavored to produce spColumn error
free the program is not and cannot be certified infallible. The final and only responsibility for analysis, design and engineering documents is the licensee's.
Accordingly, STRUCTUREPOINT disclaims all responsibility in contract, negligence or other tort for any analysis, design or engineering documents prepared
in connection with the use of the spColumn program. Licensed to: Moaaz, Moaaz. License ID: -208B1
16
STRUCTUREPOINT - spColumn v6.00 Page | 2
Licensed to: Moaaz, Moaaz. License ID: -208B1 12/18/2023
C:\Users\Moaaz\Desktop\Dotec\#2311155 - Fluid Solutions\Pile 18.col 9:28 PM
Contents
1. General Information ......................................................................................................................................... 3
2. Material Properties........................................................................................................................................... 3
2.1. Concrete ................................................................................................................................................... 3
2.2. Steel ......................................................................................................................................................... 3
3. Section............................................................................................................................................................. 3
3.1. Shape and Properties............................................................................................................................... 3
3.2. Section Figure .......................................................................................................................................... 4
4. Reinforcement ................................................................................................................................................. 4
4.1. Bar Set: ASTM A615 ................................................................................................................................ 4
4.2. Confinement and Factors ......................................................................................................................... 4
4.3. Arrangement............................................................................................................................................. 4
5. Factored Loads and Moments with Corresponding Capacities ....................................................................... 5
List of Figures
Figure 1: Column section..................................................................................................................................... 4
17
STRUCTUREPOINT - spColumn v6.00 Page | 3
Licensed to: Moaaz, Moaaz. License ID: -208B1 12/18/2023
C:\Users\Moaaz\Desktop\Dotec\#2311155 - Fluid Solutions\Pile 18.col 9:28 PM
1. General Information
File Name C:\Users\Moaaz\Desktop\Dotec\
#2311...\Pile 18.col
Project ---
Column ---
Engineer ---
Code ACI 318-14
Bar Set ASTM A615
Units English
Run Option Investigation
Run Axis Biaxial
Slenderness Not Considered
Column Type Structural
2. Material Properties
2.1. Concrete
Type Standard
f'c 4 ksi
Ec 3605 ksi
fc 3.4 ksi
εu 0.003 in/in
β1 0.85
2.2. Steel
Type Standard
fy 60 ksi
Es 29000 ksi
εyt 0.00206897 in/in
3. Section
3.1. Shape and Properties
Type Circular
Diameter 18 in
Ag 254.469 in2
Ix 5153 in4
Iy 5153 in4
rx 4.5 in
ry 4.5 in
Xo 0 in
Yo 0 in
18
STRUCTUREPOINT - spColumn v6.00 Page | 4
Licensed to: Moaaz, Moaaz. License ID: -208B1 12/18/2023
C:\Users\Moaaz\Desktop\Dotec\#2311155 - Fluid Solutions\Pile 18.col 9:28 PM
y
x
4. Reinforcement
4.1. Bar Set: ASTM A615
Bar Diameter Area Bar Diameter Area Bar Diameter Area
in in2 in in2 in in2
#3 0.38 0.11 #4 0.50 0.20 #5 0.63 0.31
#6 0.75 0.44 #7 0.88 0.60 #8 1.00 0.79
#9 1.13 1.00 #10 1.27 1.27 #11 1.41 1.56
#14 1.69 2.25 #18 2.26 4.00
4.3. Arrangement
Pattern All sides equal
Bar layout Circular
Cover to Transverse bars
Clear cover 3 in
Bars 10 #6
19
STRUCTUREPOINT - spColumn v6.00 Page | 5
Licensed to: Moaaz, Moaaz. License ID: -208B1 12/18/2023
C:\Users\Moaaz\Desktop\Dotec\#2311155 - Fluid Solutions\Pile 18.col 9:28 PM
20
DOTec Corp.
ϕ ≔ 0.9
ϕ ⋅ fy
Sd ((s)) ≔ ――――
γ ⋅ fs.max ((s))
fc ≔ 4 ksi fy ≔ 60 ksi h ≔ 24 in
db ≔ h - 3 in - 1 in = 20 in
dt ≔ h - 2 in - 1 in = 21 in
21
DOTec Corp.
22
DOTec Corp.
Vu ≔ 585 kip
23
2) Design for Punching
DOTec Corp.
24
DOTec Corp.
25
DOTec Corp.
b ≔ 5 ft
Sd ((10 in )) ⋅ MuTop
Ku ≔ ―――――― = 205.539 psi
b ⋅ dt 2
0.85 ⋅ fc ⎛ ‾‾‾‾‾‾‾‾‾‾
Ku ⎞
ρ ≔ ――― ⋅ ⎜1 - 1 - ―――⎟ = 0.00394 As ≔ b ⋅ dt ⋅ ρ = 4.962 in 2
fy ⎜⎝ 0.383 ⋅ fc ⎟⎠
⎛ As ⎞ b
n ≔ max ⎜――― 2
⎟ = 6.281 S ≔ ―= 9.552 in
⎝ 0.79 in ⎠ n
Sd ((12 in )) ⋅ MuTop
Ku ≔ ―――――― = 174.927 psi
b ⋅ dt 2
0.85 ⋅ fc ⎛ ‾‾‾‾‾‾‾‾‾‾
Ku ⎞
ρ ≔ ――― ⋅ ⎜1 - 1 - ―――⎟ = 0.00333 As ≔ b ⋅ dt ⋅ ρ = 4.2 in 2
fy ⎜⎝ 0.383 ⋅ fc ⎟⎠
⎛ As ⎞ b
n ≔ max ⎜――― 2
⎟ = 5.316 S ≔ ―= 11.286 in
⎝ 0.79 in ⎠ n
Sd ((12 in )) ⋅ MuTop
Ku ≔ ―――――― = 153.79 psi
b ⋅ dt 2
0.85 ⋅ fc ⎛ ‾‾‾‾‾‾‾‾‾‾
Ku ⎞
ρ ≔ ――― ⋅ ⎜1 - 1 - ―――⎟ = 0.00292 As ≔ b ⋅ dt ⋅ ρ = 3.679 in 2
fy ⎜⎝ 0.383 ⋅ fc ⎟⎠
⎛ As ⎞ b
n ≔ max ⎜――― 2
⎟ = 4.656 S ≔ ―= 12.886 in
⎝ 0.79 in ⎠ n
26
DOTec Corp.
27
DOTec Corp.
b ≔ 5 ft
Sd ((10 in )) ⋅ MuBot
Ku ≔ ―――――― = 216.964 psi
b ⋅ db 2
0.85 ⋅ fc ⎛ ‾‾‾‾‾‾‾‾‾‾
Ku ⎞
ρ ≔ ――― ⋅ ⎜1 - 1 - ―――⎟ = 0.00417
fy ⎜⎝ 0.383 ⋅ fc ⎟⎠
As ≔ b ⋅ db ⋅ ρ = 4.999 in 2
⎛ As ⎞
n ≔ max ⎜――― 2
⎟ = 6.328
⎝ 0.79 in ⎠
b
S ≔ ―= 9.482 in
n
28
5) Design for Circumferential Flexure
DOTec Corp.
Sd ((11 in )) ⋅ MuTop
Ku ≔ ―――――― = 194.388 psi
b ⋅ dt 2
0.85 ⋅ fc ⎛ ‾‾‾‾‾‾‾‾‾‾
Ku ⎞
ρ ≔ ――― ⋅ ⎜1 - 1 - ―――⎟ = 0.00372 As ≔ b ⋅ dt ⋅ ρ = 4.683 in 2
fy ⎜⎝ 0.383 ⋅ fc ⎟⎠
⎛ As ⎞ b
n ≔ max ⎜――― 2
⎟ = 5.928 S ≔ ―= 10.121 in
⎝ 0.79 in ⎠ n
29
DOTec Corp.
Sd ((11 in )) ⋅ MuTop
Ku ≔ ―――――― = 174.927 psi
b ⋅ dt 2
0.85 ⋅ fc ⎛ ‾‾‾‾‾‾‾‾‾‾
Ku ⎞
ρ ≔ ――― ⋅ 1 - 1 - ―――⎟ = 0.00333
⎜ As ≔ b ⋅ dt ⋅ ρ = 4.2 in 2
fy ⎜⎝ 0.383 ⋅ fc ⎟⎠
⎛ As ⎞ b
n ≔ max ⎜――― 2
⎟ = 5.316 S ≔ ―= 11.286 in
⎝ 0.79 in ⎠ n
30
Base 51 piles.fdb SAFE 2016 v16.0.0 - License #*1YELVAVPTZPDRQD
18 November 2016
Geometric Properties
Combination = ULT 2
Point Label = 9
Column Shape = Rectangular
Column Location = Interior
Global X-Coordinate = 0 ft
Global Y-Coordinate = 0 ft
31 Page 1