Professional Documents
Culture Documents
Cat
2. Remove tube assembly (1) from between the water pump and the exhaust manifold.
erp
3. Loosen clamp (2) and slide the hose off water pump elbow (3).
illa
rI
4. Remove water pump elbow (3).
nc.
6. Remove bolts (4) and the water pump. Remove the O-ring seal from the water pump.
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 1/7
1/20/24, 10:56 AM SIS 2.0
2. Slide the hose over the end of pipe (2). Put the gasket and pipe (2) in position under the
expansion tank, and install the bolts that hold it.
3. Slide the hose into position on the water pump, and tighten two clamps (3).
5. Slide hose (5) into position on the water pump, and tighten the two clamps that hold it.
6. Install the tube assembly between the water pump and exhaust manifold.
7. Fill the cooling system to the correct level. See the Maintenance Guide.
START BY:
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 2/7
1/20/24, 10:56 AM SIS 2.0
1. Remove bolt (1) and the washer. Remove bearing (2) and gear (3) as a unit.
2. Use tooling (A), (C) and a press, and remove bearing (2) from gear (3).
4. Remove bolts (5), the washers and cover (6) from the water pump.
5. Loosen bolt (7) 6.4 mm (.25 in.). Hit the bolt with a soft hammer to remove impeller (8) from the
shaft.
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 3/7
1/20/24, 10:56 AM SIS 2.0
8. Use tooling (A), (C) and a press to remove bearing (9) from shaft (10).
9. Remove the ceramic ring and seal (11) from the housing.
10. Remove lip-type seal (12) from the housing with tool (C).
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 4/7
1/20/24, 10:56 AM SIS 2.0
1. Install the lip-type seal in the water pump housing with tool (A). The lip of the seal must be toward
the bearings. Put clean engine oil on the lip of the seal.
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 5/7
1/20/24, 10:56 AM SIS 2.0
NOTICE
5. Put ceramic ring (4) in position in the rubber seal. Use hand pressure and the tool (which is with
the replacement ring) to install the ceramic ring.
6. Remove the spring from seal assembly (5). Use hand pressure and the tool (which is with the
replacement ring) to install the seal assembly. Push seal assembly (5) on the shaft until it makes
light contact with ceramic ring (4).
7. Install spring (6) as shown. Put impeller (7) in position on the shaft, and install the washer and
bolt that hold it. Tighten the bolt to a torque of 38 ± 1.4 N·m (28 ± 1 lb.ft.).
8. Put the gasket and cover (8) in position on the water pump housing, and install the washers and
bolts (9) that hold them.
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 6/7
EN 9+0
© 2 R280 3:00
1/20/24, 10:56 AM SIS 2.0
024 8
Cat
erp
illa
9. Install bearing (10) on gear (11) with a press. r In
c.
10. Put gear (11) and the bearing in position on shaft (1), and install the washer and bolt that hold
them together. Tighten the bolt to 95 ± 7 N·m (70 ± 5 lb.ft.).
END BY:
PIP-10464666
2024/01/20
07:56:31+03:00
SENR28080052
© 2024 Caterpillar Inc.
https://sis2.cat.com/#/print-preview/service/2a883f00-9b00-4bae-8b48-a2efc751e066 7/7