Professional Documents
Culture Documents
PRODUCT DESCRIPTION Coating based on modified alkyd resin. It has good adherence, flexibility and
flame retardant characteristic, reducing the spread of flame. It has test
report according to ABNT NBR 9442 – Determination of the index of
superficial spread of flame.
INTENDED USES Indicated as coating in wood and steel surfaces. Combined with fire
resistance feature, it allows a wide range of application in products that may
come into contact with direct flame or radiant heat sources, such as:
structures, fire doors and other items used in public places, residential and
industries where requires resistance and esthetic.
C ÓPI A PAR A I NF OR M AÇ Ã O
WEG COATINGS LTDA - CNPJ 12.006.058/0001-21
Matriz: Rodovia BR 280, Km 50 - Phone: (+55) (47) 3276-4000 - Fax: (+55) (47) 3276-5500 - CEP 89270-000 - Guaramirim – SC
Filial: INDÚSTRIA DE TINTAS E VERNIZES PAUMAR LTDA – CNPJ 60.621.141/0001-53
Rua Dr. Ulisses Guimarães, 800 - Phone: +55 (11) 4547-6100 – CEP 09372-050 - Mauá – SP
EMERGENCY: (+55) (11) 5012-5311 - E-mail: tintas@weg.net - www.weg.net
Page 1 of 5
Revision: 02 Date: Aug/14
TECHNIC AL DAT ASHEET – Liquid Coatings
SURFACE The performance of this product is straightly related to the surface preparation grade.
PREPARATION
Remove completely oil and grease according to SSPC-SP1 solvent cleaning.
Remove loose powdery deposits using a dry brush. High-pressured freshwater must be used to
remove all soluble salts.
Metallic surfaces
New Works: the surface must be clean, dry and free of contaminants. Remove completely oil, salts
and grease according to SSPC-SP1 solvent cleaning. Clean with high-pressured freshwater.
Repair and maintenance: the surface must be clean dry and free of contaminants. Remove
completely oil, salts and grease according to SSPC-SP1 solvent cleaning. Clean with high-pressured
freshwater.
Wood surfaces
New: apply one coat of the product 10001070 – WEGLACK SELADOR NC INCOLOR. After 2 hours
drying, sand the wood and remove completely oil, grease and other contaminants according to SSPC
SP1 solvent cleaning.
Repainting: sand the surface, removing bad adhered coatings. Remove completely oil, grease and
other contaminants according to SSPC SP1 solvent cleaning.
Respect the interval of repainting of the primer. If the time of repainting is exceeded, sand it according
to technical datasheet of the used primer.
APPLICATION: Mixing
Homogenize both base and curing agent separately using a power agitator. Ensure that any sediment
is not retained on the bottom of each pack. Mix them in accordance to the recommended ratio (by
volume), under agitation, so that a perfect homogenization is achieved.
Thinner
Recommended – Alkyd Thinner 1024
Thinning
Thinning is recommended only in special circumstances. Depending on the application method, the
maximum thinning should be 15% by volume.
Only add the thinner after completely mixing components A and B. Do not use thinners that are not
allowed by local environmental legislation.
Excessive thinning may affect film curing and the achievement of the specified dry film thickness.
C ÓPI A PAR A I NF OR M AÇ Ã O
WEG COATINGS LTDA - CNPJ 12.006.058/0001-21
Matriz: Rodovia BR 280, Km 50 - Phone: (+55) (47) 3276-4000 - Fax: (+55) (47) 3276-5500 - CEP 89270-000 - Guaramirim – SC
Filial: INDÚSTRIA DE TINTAS E VERNIZES PAUMAR LTDA – CNPJ 60.621.141/0001-53
Rua Dr. Ulisses Guimarães, 800 - Phone: +55 (11) 4547-6100 – CEP 09372-050 - Mauá – SP
EMERGENCY: (+55) (11) 5012-5311 - E-mail: tintas@weg.net - www.weg.net
Page 2 of 5
Revision: 02 Date: Aug/14
TECHNIC AL DAT ASHEET – Liquid Coatings
APPLICATION The information presented below shall be used only as a guide, similar equipment can be
METHODS: used.
Before application, make sure that all equipment and parts are clean and in good conditions.
If application stops and pot life is exceeded, do not try to restart application by thinning.
Retouch all edges and weld seam s by brush in order to prevent premature oxidation.
When painting by spray, make an extra application on 50% of the previously coated area to provide a
proper top coat finish, and then conclude the operation with a crossed coat.
Airless Spray:
Gun…………………….40:1
Fluid pressure…………1800 – 2200 psi
Hose……………………3/8” inside diameter
Tip………………………0,011” to 0,015”
Thinning………………..Max. 5%
Conventional Gun
Gun…………………….JGA 502/3 Devilbiss
Tip range………………FX
Air cap..........................704
Atomization pressure…60 to 65 psi
Tank pressure…………10 to 20 psi
Thinning………………..Max. 15%
Brush:
Recommended for small areas only.
Roller:
Recommended for small areas only. Use sheep wool roller by short and no sewing.
Note: Material may not remain in hoses, spray guns or other painting equipm ent after working pot life
is achieved.
All used equipment shall be thoroughly flushed with the proper thinner.
C ÓPI A PAR A I NF OR M AÇ Ã O
WEG COATINGS LTDA - CNPJ 12.006.058/0001-21
Matriz: Rodovia BR 280, Km 50 - Phone: (+55) (47) 3276-4000 - Fax: (+55) (47) 3276-5500 - CEP 89270-000 - Guaramirim – SC
Filial: INDÚSTRIA DE TINTAS E VERNIZES PAUMAR LTDA – CNPJ 60.621.141/0001-53
Rua Dr. Ulisses Guimarães, 800 - Phone: +55 (11) 4547-6100 – CEP 09372-050 - Mauá – SP
EMERGENCY: (+55) (11) 5012-5311 - E-mail: tintas@weg.net - www.weg.net
Page 3 of 5
Revision: 02 Date: Aug/14
TECHNIC AL DAT ASHEET – Liquid Coatings
APPLICATION For a better performance of this product, please follow the orientations below:
PERFORMANCE:
If brush or roller is used, it may be necessary more than one coating to achieve the recommended dry
film thickness.
If application occurs in maritime areas, it is recommended to wash the coated surfaces with freshwater
between each coating, to remove all loose powdery deposits and soluble salts.
Surface temperature must always be a minimum of 3°C above dew point. Do not apply if temperature
is below 0°C.
The product must not be applied in adverse conditions, such as relative humidity above 85% or
condensed surfaces. Color, aspect and gloss changes can be noticed in the film when application
occurs in high relative humidity periods, rainy or low temperature days or when the film is exterior
exposed.
For a better application performance, both components must be between 21-27°C before mixing and
painting.
Information about recoating is provided as guidance and may vary due to regional variations,
depending on the local climate conditions. For specific situations please contact WEG Technical
Department.
Some light colors may require more than one coating to provide a better perform ance.
SYSTEM
COMPATIBILITY AND
For more information, please contact WEG Technical Department.
MAINTENANCE
RECOATING:
C ÓPI A PAR A I NF OR M AÇ Ã O
WEG COATINGS LTDA - CNPJ 12.006.058/0001-21
Matriz: Rodovia BR 280, Km 50 - Phone: (+55) (47) 3276-4000 - Fax: (+55) (47) 3276-5500 - CEP 89270-000 - Guaramirim – SC
Filial: INDÚSTRIA DE TINTAS E VERNIZES PAUMAR LTDA – CNPJ 60.621.141/0001-53
Rua Dr. Ulisses Guimarães, 800 - Phone: +55 (11) 4547-6100 – CEP 09372-050 - Mauá – SP
EMERGENCY: (+55) (11) 5012-5311 - E-mail: tintas@weg.net - www.weg.net
Page 4 of 5
Revision: 02 Date: Aug/14
TECHNIC AL DAT ASHEET – Liquid Coatings
SAFETY Before handling this product, please read the material safety data sheet (MSDS), available in
PRECAUTIONS: our website.
Handling, thinning and the application of this product shall be carried out far away from flames, sparks
or excessive heat and in ventilated rooms since it is a flammable product. Appropriate protection
equipment must be used.
If the material is swallowed, do not induce vomiting. In case of eye contact, rinse them in abundant
water. In any case, seek immediate medical attention.
Make sure that electric installations are in perfect conditions and that there is no risk of spark
releasing.
Do not use solvents or thinners to wash hands or other parts of the body. Wash your hands first with
alcohol and then with abundant water and cleaning pastes. Use a skin restoring protective cream.
Paints and thinners shall be stored in ventilated rooms and protected against weathering. Storage
temperature may vary from 10 to 40ºC.
If VOC inhalation causes intoxication symptoms, move the person immediately from working area to a
ventilated room. In case of unconsciousness, seek immediate medical attention.
The use and application of this product must be in accordance to Health, Security and Environment
National Standards.
If it is necessary to remove the cured applied paint, all professionals may use personal protective
equipment, according to the MSDS.
In case of welding coated parts, face m ask for VOC contact must be used in order to avoid dust, VOC
and welding gases inhalation.
Application in closed areas requires exhaust ventilation. Contact the security area of your company.
NOTE: All information stated in this Technical Datasheet is based on WEG Coatings experience and
knowledge.
Nevertheless, as we do not have control over the use of our products, the responsibility of correct use
is exclusive to our customers. No warranty either expressed or implied can be granted or suggested
with regards to this information whatsoever. Therefore, we do not assume any liability for coverage
rate, performance or any damages or injuries resulting from improper use of the mentioned
information and durability of this product.
Some information in this Technical Datasheet is estimated and may change due to external factors
that we cannot control. WEG Coatings does not assume any liability for coverage, performance of any
material or personal injury resulting from incorrect use of this product or information mentioned in this
Technical Datasheet.
This Technical Datasheet information may change periodically, without advanced notice, due to the
continuous improvement and evolution policy of our products and services, providing high quality
solutions in order to ensure the satisfaction of our customers.
C ÓPI A PAR A I NF OR M AÇ Ã O
WEG COATINGS LTDA - CNPJ 12.006.058/0001-21
Matriz: Rodovia BR 280, Km 50 - Phone: (+55) (47) 3276-4000 - Fax: (+55) (47) 3276-5500 - CEP 89270-000 - Guaramirim – SC
Filial: INDÚSTRIA DE TINTAS E VERNIZES PAUMAR LTDA – CNPJ 60.621.141/0001-53
Rua Dr. Ulisses Guimarães, 800 - Phone: +55 (11) 4547-6100 – CEP 09372-050 - Mauá – SP
EMERGENCY: (+55) (11) 5012-5311 - E-mail: tintas@weg.net - www.weg.net
Page 5 of 5
Revision: 02 Date: Aug/14