This document provides the tasks and descriptions for the Engineering Graphics and Design course for Grade 10. It lists 6 tasks to be completed over the school year across 3 terms. For each task, the document provides the topic, total marks, relevant workbook page numbers, and study guide page references to aid completion. It outlines instructions, assessment methods, documentation requirements and additional guidelines for students.
This document provides the tasks and descriptions for the Engineering Graphics and Design course for Grade 10. It lists 6 tasks to be completed over the school year across 3 terms. For each task, the document provides the topic, total marks, relevant workbook page numbers, and study guide page references to aid completion. It outlines instructions, assessment methods, documentation requirements and additional guidelines for students.
This document provides the tasks and descriptions for the Engineering Graphics and Design course for Grade 10. It lists 6 tasks to be completed over the school year across 3 terms. For each task, the document provides the topic, total marks, relevant workbook page numbers, and study guide page references to aid completion. It outlines instructions, assessment methods, documentation requirements and additional guidelines for students.
ENGINEERING GRAPHICS AND DESIGN GRADE 10 TASK DISCRIPTION
GRADE 10 ENGINEERING GRAPHICS AND DESIGN TASKS FOR THE YEAR
Task Description Total Workbook Study guide
INSTRUCTIONS Term 1 1. All the work of each chapter must be completed first, before the formal task is done. Task 1.1 Freehand drawing 10 p. 9 p. 2-3 – 2-32 2. The drawings must only be drawn on the drawing sheets in the printed A3 workbook p. 4-3 – 4-17 and not with CAD. Task 1.2 Geometrical construction 10 p. 25 and p. 3-3 – 3-12 3. Under no circumstances may the memorandum be seen, used or copied from. Task 1.3 Construction of an ellipse 10 p. 23 right p. 4-18 – 4-20 4. Take note: • Printed A3 workbook (provided by Impaq) Term 2 • Loosen the drawing sheets and draw the sketches on it. p. 5-3 – 5-30 Task 3.1 Mechanical castings 20 p. 41 • The page numbers of each formal task are indicated in the table to the right. and p. 5-34 – 5-50 p. 5-3 – 5-30 Task 3.2 Mechanical castings 20 p. 45 - 46 Due date Refer to my.Impaq for due dates. and p. 5-34 – 5-50 Method of assessment Memorandum Task 3.3 Isometric drawing 10 p. 55 p. 6-3,6-9 – 6-15 Contact Contact the education specialist at Impaq or send an email to Term 3 akademie@impaq.co.za. Task 5.1 Solid geometry 10 p. 78 p. 8-3 – 8-26. Important • Workbook • Final formal drawing documentation and • Study guide Task 5.2 Descriptive geometry 10 p. 85 p. 7-3 – 7-12 proof p. 11-3 – 11-16 Task 5.3 Floor plan 20 p. 102 Requirements • Standard drawing equipment for EGD is required to complete the and p. 11-18 – 11-29 task. p. 11-3 – 11-16 Task 5.4 Sectional elevation 20 p. 112 - 113 • A non-programmable calculator may be used. and p. 11-18 – 11-29 • The study guide may be used for reference. Task 5.5 Perspective drawing 10 p. 130 p. 6-20 – 6-25 Additional guidelines • Read the instructions and assignment thoroughly. p. 12-3 – 12-22 Task 5.6 Electrical diagram 10 p. 114 - 115 • All construction must be shown on the drawings, as well as all and p. 11-32 – 11-34 calculations where applicable. • Drawings must be neat and accurate. • Include the necessary information on the drawings and drawing sheets. • This is individual work.