Professional Documents
Culture Documents
QA QC in Construction
Table of Contents
Method Statement for Interior and Exterior Lighting System Installation | Interior Lighting
System | Exterior Lighting System
Method Statement for Interior and Exterior Lighting System Installation:
1. Purpose:
2. Scope:
3. Reference:
4. Material and Equipments:
5. Procedure:
5.1 Safety:
5.2 Work Sequence and Methodology:
5.3 Handling and Storage:
6. Interior Lighting Installation:
6.1 Pre-Installation:
6.2 Installation:
6.3 Testing:
7. Exterior Lighting Installation:
7.1 Pre-Installation:
7.2 Installation:
7.3 Testing:
8. Lighting Control Devices:
8.1 Wiring Devices:
8.2 Installation:
8.3 Connection:
8.4 Testing:
OTHER POSTS:
Method Statement for Electrical Wires and Power Cables Installation
Method Statement for Installation of Electrical Conduit and Boxes
Method Statement for Interior and Exterior Lighting System Installation
Method Statement for Installation of Cable Tray or Trunking
Conclusion:
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 1/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
2. Scope:
This method statement defines the responsibilities and describes the activities and general
procedures for the following: Wiring Interior and Exterior Lights
Installation of Lighting System for Interior and Exterior, lighting control devices and
wiring devices according to approved shop drawings, technical specification & other
related codes and reference standards.
Coordination of the exact design layout, fixture layout and its installation, positions
of
fixtures and wiring devices, ducts, pipes, other installations and ceiling panels / tiles.
This procedure shall be applied to the inspection, method and criteria for installation
work carried out by the Electrical Department.
This Method of Statement covers the procedure pertaining to the installation and
inspection activities for Interior & Exterior Lighting unit systems and Lighting
control devices. Wiring Interior and Exterior Lights
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 2/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
3. Reference:
Shop drawings
Specification
Material submittal
Project Quality plan
Project HSE Plan
Civil Defense Approval Wiring Interior and Exterior Lights
Safety requirements tools such as safety shoes, safety helmet, safety glasses, fluorescent
vest, and safety gloves to ensure maximum ability of safe work and dust mask when require
5. Procedure:
5.1 SAFETY:
Ensure only trained Authorized & licensed persons only shall operate the power tools
and
do the Installation and Testing job.
All hand tools and power tools shall be good in quality and working condition.
Personal Protective Equipment ( PPE) required varying type of works.
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 3/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 4/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
Check all material delivered to site is inspected properly by QA/QC Inspector and
check if it is stored properly as per manufacturer’s recommendations.
MIR shall be raised for the inspection of materials received at site to the Consultant
Engineer. Outdoor Lighting Installation
Work shall be carried out by the site staff under strict supervision and guidance of
the
concerned Supervisors/ Foremen / Engineers.
The QA/QC Inspector shall check all the installations as per the Installation Check list.
MIR shall be prepared by QA/QC Inspector and will be submitted to Consultant for
their
inspection and approval. Landscape Lighting Installation
QA/QC Inspector shall coordinate with other contractors and arrange inspection for
installation to the Consultant Engineer.
QA/QC Inspector is responsible for all installation activities for getting the work
inspected and approved by Consultant Engineer.
covering and stored in a dry location free from dust or water and in such a manner to
permit easy access for inspection and handling. Luminaires, Lamps and accessories
shall be handled carefully to prevent damage. Outdoor Lighting Installation
6.2 INSTALLATION:
Ensure fixtures level are installed, aligned and parallel or square to building lines at
uniform heights as shown on the approved shop drawings and final height
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 6/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 7/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
6.3 TESTING:
Perform Illumination level test to determine level and uniformity at selected
locations.
Perform Operational test for each fixture after installation.
Perform electrical supply interruption demonstrate proper operation of emergency
lighting. Indoor Lighting Installation
Perform Insulation resistance and continuity test for each circuit and circuit breaker
for
equipment before Energization.
Perform operational test for all circuit breakers and control gears with lamps
Installed.
Proper type, size, colour and number of wires and cable are being installed.
Test results are to be recorded on site. Lighting Installation Procedure
7.2 INSTALLATION:
Ensure equipment’s are installed to be readily accessible for operation, maintenance
and
repair. Indoor Lighting Installation
Daily housekeeping shall be conducted after work, especially to remove left-over
materials from the work area.
Ensure that Holding down and plumb adjusting nuts, washers, locknuts or nuts are to
be
stainless steel or cadmium plated.
Luminaires and supports are to be attached to allow aiming for indicated light
distribution. Lighting Installation Procedure
Floodlights are to be mounted on specially designed brackets to allow swivelling in
any
desired direction and locking firmly in final position.
Fasten luminaire to indicate structural supports.
Tighten electrical connectors and terminals according to manufacturer’s torque.
Tightening values. Lighting Installation Procedure
Clean fixtures internally and externally after installation.
7.3 TESTING:
Perform Insulation resistance and continuity tests are to be carried out on each
circuit with circuit breakers in open position and lamps not installed.
Perform Operational test for all circuit breakers and control gears with lamps
installed.
Voltage at terminals of ballasts are to be recorded on final columns of each circuit
and at
distribution panel. Indoor Lighting Installation
Perform Operational test for each fixture after installation.
Perform Illumination level test to determine level and uniformity at selected
locations.
Perform Earthing resistance tests which includes measurement of earth electrode
resistance at final points of circuits and continuity of protective conductors.
Test normal operation of lighting units after installing luminaires.
Measure light intensities at night. Use calibrated photometers.
Ensure Intensity and uniformity of illumination are checked.
Malfunctioning fixtures and components should be repaired or replaced.
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 9/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
8.2 INSTALLATION:
All lighting control devices and components shall comply with the applicable
standards of
SASO, NEMA, NEC, B8 and ANSI. Lighting Installation Procedure
Lighting control devices are mounted according to manufacturer’s instructions.
For suspended devices: Mounting heights are to be bottom of the unit and to centre.
For wall-mounting devices: Mounting heights are to be centre of unit.
Install wiring between sensing and control devices according to manufacturer’s
instructions.
Ensure that master selector switch panel comprise set of switch buttons of normally
Open type assembled in one-unit comprising box and cover with individual switch
per
circuit.
Bundle, trail and support wiring in enclosures.
Ensure Proper Grounding is done for the equipment.
Tighten electrical connectors and terminals with torque wrench to manufacturers
torque
tightening values. Lighting Installation Procedure
Proper identification shall be done to identify components and power and control
wirings.
Clean equipment and devices internally and externally and repair damaged finishes.
Exact locations of outlets and switching devices are to be determined from interior
finishing and detailed approved drawings. Any condition that would place an outlet in
an unsuitable location is to be referred to the engineer.
Locate switches at strike sides of doors.
Mounting heights for outlet boxes and switches are to be uniform within similar
areas.
Mount lighting switches at 1350 mm (100mm from door frame, horizontally) and
socket outlets at 300 mm from finished floor level respectively. Mount switches with
long dimension vertical and operating handle, if of toggle type up when in on
position.
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 10/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
Make neat openings for recessed outlet boxes allowing for thickness of finishing and
use extension rings if required.
Install exposed boxes and plates plumb, square and parallel to finished wall surface.
Exposed plates covering recessed boxes are to rest neatly on wall surface without
gaps
and fully covering the box.
Grouped outlets are to be arranged neatly so that use of fittings is convenient and
clear.
Water and explosion proof fittings shall be installed securely to achieve required
degree of protection. Interior and Exterior Lighting Methods
Where appliance is designed to adapt directly to outlet box, extend wiring to
incoming
terminals inside appliance.
Where appliance is not designed to adapt to outlet box, install connecting wiring in
flexible conduit firmly fixed to outlet box cover plate and to terminal box on appliance.
Where three or more switches are ganged, identify each switch with approved legend
engraved on wall plate.
Receptacles should be identified by panel board and circuit number from which
served.
Use machine printed, pressure sensitive, abrasion resistant label tape on face of
plate and durable wire markers or tags within outlet boxes. Interior and Exterior
Lighting Methods
8.3 CONNECTION:
Single pole switches are to switch the phase wire.do not run neutral wire through
switches having neutral shunt or bridge. Interior and Exterior Lighting Methods
Exposed outlet boxes should be securely fastened to wall with machine screws.
Tighten electrical connectors and terminals as per manufacturers torque tightening
values using torque wrench.
Internally clean devices, outlet boxes and enclosures. Replace stained or improperly
painted wall plates or devices. Interior and Exterior Lighting Methods
8.4 TESTING:
Perform Continuity and operational tests of circuits.
Settings of photoelectric devices with photometer are to be verified.
Perform Operational tests to set and operate devices to demonstrate their functions.
Perform testing of devices under conditions that simulate actual operational
conditions.
Control settings, operations, cues and functional observations are to be recorded.
Visually inspect fittings and equipment’s for fixing and workmanship.
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 11/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
Megger tests are to include switch and socket outlet test together with insulation
resistance of wiring installations. Interior and Exterior Lighting Methods
Devices are to be tested for operation and are to perform as intended at full load
without
any signs of heating. Interior and Exterior Lighting Methods
Equipment is to be insulation tested and observed under full load for not less than 3
days’ operation, with respect to undue heating and performance in general.
OTHER POSTS:
1. Method Statement For Electrical Wires And Power Cables Installation
2. Method Statement For Installation Of Electrical Conduit And Boxes
3. Method Statement For Interior And Exterior Lighting System Installation
4. Method Statement For Installation Of Cable Tray Or Trunking
CONCLUSION:
Full article on Interior and Exterior Lighting System Installation | Wiring Interior and
Exterior Lights | Outdoor Lighting Installation | Indoor Lighting Installation | Outdoor
Lighting Installation | Landscape Lighting Installation | Interior and Exterior Lighting
Methods | Method Statement for Interior and Exterior Lighting | Lighting Installation
Procedure. Thank you for the full reading of this article in “QA QC in Construction”
platform in English. If you find this post helpful, then help others by sharing it on social
media. Please share this article on social media for future uses.
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 12/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
https://qaqcinconstruction.com/
QA QC in Construction
A guide for Quality Assurance and Quality Control Professionals. Quality assurance and quality control in
construction is a guide for quality engineers in the field of civil, electrical, mechanical and HVAC etc. This
is an online institution that teaches how to assure and control the work in construction and the
materials as well.
RELATED POSTS
METHOD STATEMENT FOR ELECTRICAL WIRES AND POWER CABLES INSTALLATION
April 5, 2022 | Electrical Engineering
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 13/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 14/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
Leave A Comment
Name *
Email *
Website
Save my name, email, and website in this browser for the next time I comment.
Post Comment
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 15/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
MOST RECENT
More
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 16/17
1/23/24, 12:51 PM Method Statement for Interior and Exterior Lighting System Installation
https://qaqcinconstruction.com/method-statement-for-interior-and-exterior-lighting-system-installation/ 17/17