Professional Documents
Culture Documents
TM
SemiSel Prepared by: Vinh
Calculation Report Application:
Customer:
File name: project 1
Description:
1. Circuit Parameter 2
1.1 Nominal Load 2
1.2 Extended Overload Configuration 2
2. Product 3
3. Cooling 5
3.1 Product Arrangement 5
3.2 Fixed Heatsink Temperature 5
4. Calculation Results 6
4.1 Nominal Load 6
4.2 Overload 7
IMPORTANT INFORMATION AND WARNINGS 8
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 1/8
1. Circuit Parameter
AC/DC: B2U
30
28
26
24
22
20
30
28
26
24
22
20
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 2/8
2. Product
SKB 30/08 A1
D1 D2
Iref 30 A 30 A
Vref 0V 0V
Tj op 135 °C 135 °C
Tj max 150 °C 150 °C
Vf @ 25°C, Iref 1.18 V 1.18 V
Vf @ Tjop, Iref 1.11 V 1.11 V
RgOn
RgOff
Eon
Eoff
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 3/8
D1 D2
Rth(j-c) 4.2 K/W 4.2 K/W
Rth(c-s)
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 4/8
3. Cooling
Heatsink temperature: 50 °C
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 5/8
4. Calculation Results
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 6/8
4.2 Overload
Temperature maxima
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 7/8
IMPORTANT INFORMATION AND WARNINGS
The information provided in this document may not be considered as guarantee or assurance of product
c harac teris tic s ("Beschaffenheitsgarantie"). S E MIK R O N does not assume any warranty or liability with
respect to the accuracy, correctness, completeness and/or use of any information in this document. This
document describes only the usual characteristics of products to be expected in typical applications, which
may still vary depending on the specific application. Therefore, products must be tested for the respective
application in advance. Application adjustments may be necessary. The user of S E MIK R O N products is
responsible for the safety of their applications embedding S E MIK R O N products and must take adequate
safety measures to prevent the applications from causing a physical injury, fire or other problem if any of
S E MIK R O N products become faulty. The user is responsible to make sure that the application design is
compliant with all applicable laws, regulations and standards. Except as otherwise explicitly approved by
S E MIK R O N in a written document signed by authorized representatives of S E MIK R O N, S E MIK R O N
products may not be used in any applications where a failure of the product or any consequences of the use
thereof can reasonably be expected to result in personal injury.
© by Semikron Danfoss / 2024-03-20 / SemiSel Report (SemiSel V5 - B 20240215.4 - Db 20240318152859) Page 8/8