Professional Documents
Culture Documents
B0302-CK3 Third-Level Clock Board
B0302-CK3 Third-Level Clock Board
Functions
As the clock interface board, the CK3 board contains the third-level
constant-temperature crystal chip. To ensure the high accuracy and stability of the
timing signal, the CLK board traces the external reference signal, screens jitters of
the external reference by the phase-lock performed by the software. If it loses the
external reference, the board may work in the free oscillation mode or memory mode.
It outputs such signals as: square waves of 32.768MHz, 8.192MHz, 4.096MHz,
2.048MHz, 1.024MHz, 8kHz and 4kHz; TTL level signal of 4MHz, 8kHz and 4kHz;
RS422 level signal of 8.192MHz, 2.048MHz, 1.024MHz, 8kHz and 4kHz.
It reports the information on the board to the background via the SLT board and
receives commands from both of the background and SLT board.
Because it is capable of providing all functions of the SYN board, so it can be used as
the C804SYN board. It is also compatible with the third-level clock.
Its active/standby phasic synchronization circuit design ensures the phase
synchronization between the active and standby board. Since the phase of standby
board is synchronous to that of the active board, negative impacts on the external
equipment is reduced as more as possible.
Note * :
On: memory mode;
Fast flash: fast mode;
Slow flash: tracing mode;
Page 1 of 4
Board Manual
C&C08 Digital SPC Switching System B-0302
Off: free oscillation.
OFF S3
Figure 1 Setting of S3 (the board is in the state of the forceful reset)
2) S3 is set as illustrated in Figure 2 while the SYN board is replaced by the CK3
board that is forced to work in the third-level clock mode.
ON
OFF
S3
Figure 2 Setting of S3 (forced to work in the third-level clock mode)
Page 2 of 4
Board Manual
C&C08 Digital SPC Switching System B-0302
ON
OFF
S3
Figure 3 Setting of S3 (the external operating mode is selected by the software, the SYN board is
replaced by the CK3 board)
4) S3 is set as illustrated in Figure 4 while the board is forced to work in the low
baud rate communication and the CK3 can not be used as the SYN board.
ON
OFF
S3
Figure 4 Setting of S3 (the board is forced to work in the low baud rate communication)
5) S3 is set as illustrated in Figure 5 while the CK3 board is inserted into the clock
frame, works in the low baud rate mode; or the CK3 board is inserted into the
slot of the SYN board and works in the high baud rate mode.
ON
OFF
S3
Figure 5 Setting of S3 (CK3 is inserted into the clock frame or inserted into the slot of SYN board)
Besides setting of S3 as illustrated above, two types of the setting can also be given
as follows, taking references of what described above. Special requirements can also
be met making certain modification to figures above.
6) S3 is set as illustrated in Figure 6 while the CK3 board is inserted into the clock
frame (default setting).
Page 3 of 4
Board Manual
C&C08 Digital SPC Switching System B-0302
ON
OFF
S3
Figure 6 Setting of S3 (the CK3 board is inserted into the clock frame)
7) S3 is set as illustrated in Figure 7 while the CK3 board is inserted into the slot of
the SYN board.
ON
OFF
S3
Figure 7 Setting of S3 (the CK3 board is inserted into the slot of the SYN board)
External distribution
Please see related specifications of the CKB board.
Page 4 of 4