Professional Documents
Culture Documents
Tle Review Drafting Carpentry Masonry Plumbing Electricity 180918012335 PDF
Tle Review Drafting Carpentry Masonry Plumbing Electricity 180918012335 PDF
E
Technology and Livelihood Education
Drafting Electricity
Carpentry Electronics
Masonry Cosmetology
Plumbing Foods
Entrepreneurship
Drafting
Drafting
The process of drawing to communicate ideas and
instructions to others.
Most manufactured products and all major buildings
were first created on drawing boards
Drafting Equipment
T square –instrument used in drawing horizontal
lines. It is also used in guiding triangles when
drawing vertical lines.
Drafting Equipment
Triangle – a three sided ruler which has typically two
equal sides meeting at 900.
30 x 60 and
45 x 45 degrees.
Drafting Equipment
Divider - is used to create equal distances, transfer
measurements and spacing points or lines
Drafting Equipment
Masking tape - material used for fastening the
drawing paper on the drawing table.
Drafting Equipment
Erasing Shield - is a useful tool to protect the rest of
the drawing when clearing up smudges,
unnecessary pencil lines and other erasures.
Drafting Equipment
Pencil - is made of a much better grade of graphite, commonly called lead
which is used in drawing lines. (9H, 8H, 7h, 6H, 5H, 4H, 3H, 2H, H, HB, B,
2B, 3B, 4B, 5B, and 6B)
Drafting
[1]
[2]
[3]
[4]
Day
Drafting (Kinds of Letters)
Gothic – all letters are composed of uniform width
elements
ABCDEF abcdef
Roman – letters have strokes (accented), or made
up of thick and thin elements
ABCDEF abcdef
Text – elements are made with style C or D
speedball pens. Old English, church text.
ABCDEF abcdef
Drafting (Lines)
[1]Dimension line - used to indicate the measurement of objects
which are represented by dark solid lines.
[2]Extension line – fine line used to show clearly the dimension
limits.
[3]Center line – light broken lines used in circles, sometimes as
extension line
[4]Leader line – line leading from a dimension value, or explanatory
note to the feature on the drawing. An arrowhead is used in pointing
end but not in note end.
[5]Long break – a limiting line used to limit the length of elongated
object.
[6]Invisible line - a series of light dash line that represents parts of a
drawing that are not seen.
Border line - is considered as the darkest lines that surround a
drawing usually in rectangular shape
Drafting (Lines)
[1]Dimension line
[2]Extension line
[3]Center line
[5 [4]Leader line
] [5]Long break
[6]Invisible line
[2 [1
] ]
3’’ [3
]
[4]
[6]
Drafting (Isometric Drawing)
It presents the object in 3 views, FV (Front View), TV (Top View) and
RSV (Right Side View).
Three axes are needed to perform isometric drawing, the vertical
axis, left 300 axis and right 300 axis (a=1200 , b=1200 , c=1200 )
Drafting (Isometric Drawing)
The drawing that has equal measure.
The BOX method is the starting point of isometric drawings.
Drating (Pictorial Drawing)
Axonometric Drawing – the object turned so
that three faces are viewed simultaneously
Oblique Drawing
a pictorial drawing having one side parallel to the
picture plane. It maybe drawn at any convenient
angle.
Drating (Pictorial Drawing)
Types of Oblique drawing
Cavalier –the width, depth and height is the true length or
size (Actual representation)
Cabinet –the depth is reduced to one half. The front is
actual size, while the depth of top and right side are
drawn one half to the actual
Drating (Pictorial Drawing)
Perspective Drawing – the most realistic, the object is
drawn as it seen by the naked eye.
One point drawing (Vanishing Point)
Two points drawing
VP
Drafting (Perspective)
Sample Question 1
b c
A.) Perspective a
B.) Isometric
C.) Orthographic
D.) Technical
Sample Question 2
A.) Gothic
B.) Roman
C.) Text
D.) Old English
Sample Question 3
[a] Sapwood
[b] Heartwood
[c] Cambium layer
Carpentry (Parts of a Wood)
Layers
Carpentry (Lumber Defects)
Defects
Carpentry (Quality of wood)
S2S – planed or smooth on two sides
S4S – planed or smooth on four sides
Carpentry (Unit of Measurement of wood)
Varnish - a finishing
material when
applied produces
high glossy finish to a
project. It came in
different forms, from
gum, linseed oil,
resin, turpentine and
or chemical drier.
Carpentry (Joints)
Butt joint – the end of one piece is fastened to the surface or edge
of other piece.
Carpentry (Joints)
Milter joint – the corners are cut usually at 45 degrees and joined
forming right angle.
Carpentry (Joints)
Mortise and Tenon – is one of the strongest joint used for quality
chairs, tables and benches. (Force Fitting)
Carpentry (Joints)
Dado - is a groove that runs on board and receives the end or edge
of the second board. (“TnG”)
Carpentry (Joints)
•Push Pull Steel Tape Rule - steel tape is assembled in a fixed casing and
retracts automatically by spring.
Carpentry (Common Tools)
Knife is used when you know that the marks will disappear.
Carpentry (Common Tools)
Sliding T Bevel - this tool can be set to lay out any angle.
Carpentry (Common Tools)
Scratch awl is used to lay out positions for drilling and boring holes.
Carpentry (Common Tools)
Clamp is used for gluing up large surfaces, edge to edge and for
clamping parts together when assembling projects.
Carpentry (Holding Tools)
Brace – it is used for holding auger bits, fastener bits and other tools
with rectangular shape shanks.
Carpentry (Cutting Tools)
Backsaw – it has stiff blades for more accurate work both on the
bench and the vise.
Carpentry (Cutting Tools)
Brace – it is used for holding auger bits and other tools with
rectangular shape shanks.
Carpentry (Boring Tools)
Drill – a set of twist drills used for drilling both metal and wood.
Carpentry (Boring Tools)
Ball Peen Hammer – it has a round knob at the back of the hammer.
It is used in metal work
Carpentry (Holding Tools)
Vise is used for holding a work of piece to allow work to be performed in it.
Clamp is used for gluing up large surfaces, edge to edge and for clamping
parts together when assembling projects.
Brace – it is used for holding auger bits, fastener bits and other tools with
rectangular shape shanks.
Carpentry (Cutting Tools)
Gable Roof. This roof has two roof slopes that meet at the center
(ridge), forming a gable. It is the most common roof because it is
simple, economical, and may be used on any type of structure.
Hip Roof. This roof has four sides or slopes running upward toward
the center of the building to create a ridge (or peak)
Lean-To or Shed Roof. This roof used where hasty or temporary
construction is needed and where sheds or additions to buildings are
erected.
Valley Roof. This roof is framed of two intersection hip or gable
roofs. The two roofs meet at a valley.
Sample Question 1
A.) (T” + W” + L’ )* 10
B.) (T” x W” x L’ )/ 10
C.) (T” - W” - L’ )/ 12
D.) (T” x W” x L’ )/ 12
Sample Question 2
Roughing up tools
Plumb bob is used in guiding the vertical position in
laying bricks
Masonry (Tools)
Any structure with a house drain installed, must have at least one soil
stack or stack vent extended full size above the roof.
Not less than 3” or 75mm diameter, no less than 2 m above the
roof if the roof is used other than protection from the elements of
weather.
The ideal position of horizontal pipe, were those installed at 2%
slope. 2 cm per 1 meter length, a 3 meters pipe will have inclination
of 3x2=6 cm.
The house drain shall be provided with adequate number of
cleanouts to facilitate troubleshooting or cleaning in case of
stoppage or flow. Every 20 m space
Plumbing (Types of Pipe)
Rigid type
Polyvinyl chloride (PVC)
Chlorinated Polyvinyl chloride (CPVC)
Styrene Rubber Plastic (SR)
Flexible type
Polyethylene (PE)
Polybuthylene (PB)
Copper pipe – used in installing hot water
supply
PVC pipes quickly installed using solvent
cementing.
Plumbing (The Septic Tank)
Septic Tank – is is the receptacle or vault used to collect organic waste
discharge from the house sewer.
An ideal size of septic tank is 1.3 cu.m, for 6 family members
A very large tank is not advisable because the bacterial activities would be
retarded.
Bacteriological Processes
Sedimentation process - decomposition in the upper portion of the tank
(with the scum)
Anaerobic decomposition –decompo-sition of the sludge at the bottom of
the tank.
Sludge – a semi-liquid substance accumulated at the bottom of the septic
tank.
Scum – a floating substance at the septic tank.
The minimum distance required between the septic tank and residence is
ten feet (10’)
The minimum distance required between the well and septic tank is seventy-five feet
(75’)
Plumbing (Tools and Materials)
Fittings
Nipple – a short pipe with small opening which provides
way for liquid to pass through the pipe. It has a male
thread on each end and is used for extension from fitting.
Plumbing (Tools and Materials)
Fittings
Bushing - fittings that can be inserted into one pipe and
allow you to screw another (smaller pipe) pipe into it.
Plumbing (Tools and Materials)
Fittings
Coupling – a fitting device used to connect two shafts
together at their ends.
Plumbing (Tools and Materials)
Fittings
Union – like coupling, except it is designed to allow quick
and convenient disconnection of pipes for maintenance.
“Union Patente”
Plumbing (Tools and Materials)
Fittings
Plug – cap end, designed to insert into the end of tube to
end the flow of water.
Plumbing (Tools and Materials)
Fittings
Cap – similar to plug, it covers the end of a pipe.
Plumbing (Tools and Materials)
Fittings
Elbows – ¼ bend, 45 degrees and 90 degrees, to change
direction
Plumbing (Tools and Materials)
Fittings
Reducer – used to connect smaller pipe from a larger
pipe.
Plumbing (Tools and Materials)
Fittings
Tee
Plumbing (Tools and Materials)
Fittings
Wye
Plumbing (Tools and Materials)
Valves
Gate valve – it is used to permit or prevent the flow of
water.
Plumbing (Tools and Materials)
Valves
Check valve – a device which allows liquid to flow
through it in only one direction. It is often used in some
types of pumps – inlet and outlet ball check valves.
Plumbing (Tools and Materials)
Valves
Inlet valve – it is used to control the pressure of the flow
of water.
Plumbing (Tools and Materials)
Valves
Flush valve – device
located at the bottom
of the tank for
flushing water
closets.
Plumbing (Tools and Materials)
Valves
Float valve – used in filling water tanks, avoiding
overflow and backflow of water.
Sample Question 1
A.) RA7077
B.) RA6442
C.) RA 1387
D.) RA 1378
Sample Question 2
A.) Tee
B.) Union
C.) Reducer
D.) Elbow
Electricity
Electricity
Electricity is a form of energy resulting from the
existence of charged particles (such as electrons &
protons). Either statically on an accumulation of
charge of dynamically a current
Current Directional flow of electric charge
Insulator vs. Conductor
Electricity (Sources)
Biomass – all solid materials from plants and animals
which energy may be extracted.
Advantages of Biomass Energy
Renewable energy source
Very low greenhouse gas emissions
Can produce energy on-demand
Energy is easily stored
Disadvantages of Biomass Energy
Low energy return on investment
High air pollution emissions
Very high water and land requirements
High occupational hazards
Geothermal Energy – heat energy of the earth.
Electricity (Sources)
Hydropower – force of moving water from rivers and water
reservoirs.
Advantages of Hydropower
Very high return on energy investment
Very low greenhouse gas & air pollution emissions
Inexpensive once dam is built
Disadvantages of Hydropower
Very high land requirements
Extremely high impacts to land and water habitat
Best sites are already developed or off-limits
Disastrous impacts in case of dam failure
Ocean Power – energy from the currents and waves.
Marine Currents
Two-way currents – caused by ocean tides.
One-way currents – ocean water flowing like rivers.
Electricity (Sources)
Solar Energy – heat energy provided by the sun
Advantages of Solar Energy
Renewable energy source
Very low greenhouse gas emissions
Very low air pollution emissions
Very low water requirements
Modular, low-profile, low-maintenance
Very safe for workers and public
Disadvantages of Solar Energy
Intermittent energy source
High land requirements
Expensive
Manufacture involves some toxics
Electricity (Sources)
Wind Power – energy from the force of the wind.
Advantages of Wind Power
Renewable energy source
Very low greenhouse gas emissions
Very low air pollution emissions
Very low water requirements
Very safe for workers and public
Disadvantage of Wind Power
Intermittent energy source
Limited to windy areas
Potentially high hazard to birds
Moderate land requirements
Electricity (Sources)
Coal Energy – energy derived from burning coals, a rock
mostly made of carbon element.
Advantages of Coal Energy
Inexpensive
Abundant
Low land requirements
Can produce energy on-demand
Disadvantages of Coal Energy
Non-renewable energy source
Very high greenhouse gas emissions
Very high air pollution emissions
High land/water impacts from acid rain, mine drainage
Highly hazardous occupation
Electricity (Sources)
Nuclear Energy – energy trapped inside the atom, the same with the
principle of producing energy by heat.
Advantages of Nuclear Energy
Low greenhouse gas emissions
Low air pollution emissions
Low land requirements for power plants (though not for waste
storage)
Can produce energy on-demand
Disadvantages of Nuclear Energy
Non-renewable energy source
High water requirements
Relatively expensive
Waste remains dangerous for thousands of years
Serious accident would be disastrous
Electricity (Sources)
Natural Gas – energy from methane, a combination
of hydrogen and carbon, formed when organic
matters are trapped beneath the sedimentary layers
of the earth.
Electricity (Types of Current)
Alternating Current (AC) - the flow of electrons changes
alternately. It goes positive, and then it goes negative,
and so on as a cycle.
It reverses direction 120 times per second, or 60 cycles
per second – called 60 hertz power.
Direct Current (DC) - the flow of electron in a conductor
is only in one direction.
It flows from negative pole, through a device, and on the
positive pole.
Sources:
Chemical battery , Electronic power supply, and
Mechanical Generator
Electricity (Types of Electricity)
Static Electricity – electricity at rest, the buildup of
electric charge on the surface of objects.
Electricity produced by friction
Dynamic Electricity – the flow of electric charge,
also known as electric current. It also known as
electricity in motion.
Electricity (Electric Circuit)
RT=R1+R2+R3
RT=10+10+20
RT=40Ohms
Electricity (Types of Circuit)
Parallel Circuit
Loads are connected side by side across the path of the
current.
Current in each branch is independent from each other, when branch or load
opens, the other load will still function.
Current is equal to the sum of the individual currents.
(Itotal = Il+I2+I3….)
Voltage drop across each load is the same. (Vtotal = Vl=V2=V3….)
Resistance is found by this formula:
1
-----------------------
1 1 1
--- + --- + ---
R1 R2 R3
Electricity (Types of Circuit)
Parallel Circuit
Resistance is found by this formula: (Product over sum)
RT= (R1)(R2)
R1 + R2
RT= (10) (20)
10 + 20
RT= 200
30
RT= 66.66Ohms
Electricity (Types of Circuit)
Series and Parallel Circuit
Combination of series and parallel connection in one circuit.
Electricity (Ohms Law)
OHM’S LAW
George Simoun Ohm – discovered the
relationships of voltage, current and resistance in
a circuit.
Current is directly proportional to voltage
Increase in voltage will result to increase in current
Current is inversely proportional to resistance
Increase in resistance will result to a decrease in
current
Electricity (Basic Computation)
QUANTITY UNIT SYMBOL FORMULA
How to determine the Ampere required for a voltage of 12V and a resistance
of 1o ohms.
I=V/R
I= 12 /10
I=1.2
The Ampere required is 1.2A
Electricity (Voltage “V”)
Ampere is represented as “I”
Voltage is represented as “V”
Resistance is Represented as “R”
V=I x R
V= 2 x 14
V=28
The Voltage required is 28V
Electricity (Resistance “R”)
Ampere is represented as “I”
Voltage is represented as “V”
Resistance is Represented as “R”
R=V/I
R= 24 x 2
R=12
The Resistance is 12Ohms
Electricity (Power “P”)
Ampere is represented as “I”
Voltage is represented as “V”
Power is Represented as “P”
How to determine the Power (Watts) for a current of 30A and a Voltage of
220V.
P=V x I
P= 220 x 30
P=6600
The Power or watts is 6600W
Electricity (Trick of the trade)
V P
I R I V
Electricity (Circuit Protection)
Breaker – an automatically operated electrical switch designed to protect
electrical circuit caused by overload or short circuit.
(Fuse operates once, must be replaced. Breaker can be reset to resume
normal operation).
20 amp – for convenience outlets (general purpose)
15 amp – for lighting fixtures
30 amp – for heavy duty appliance outlets (SPO) such as ref and aircon.
60 amp - for main breaker
Electricity (Circuit Conditions)
Overload – when the total current flowing in the circuit is more than the
capacity of the conductor.
Short Circuit – when insulated conductors from line 1 and line 2 of a circuit
come into contact with each other without passing any load, or when the
resistance of the load becomes unnecessary low.
This is dangerous because it creates a very high flow of current which
produces unusual heat and may cause fire.
Grounded circuit = when one uninsulated conductor touches the metal part
of an appliance. It causes voltage drain, and electrocution when touch by
uninsulated individual.
Open circuit = when the flow of the current is incomplete. When circuit is
switched off.
Closed circuit = when the flow of current is complete. When circuit is
switched on.
Electricity (Basic requirements in electrical house
wiring)
Prepare a house wiring plan in accordance with the safety standards of the
PEC
PEC – Philippine Electrical Code or NEC – National Electrical Code
Philippine Association of Mechanical and Electrical Engineers (PAMEE)
Determine the load and compute for the expected power and current
consumption.
Identify the service point where electricity will come from
Determine the number of outlets per branch and their specifications
Determine the sizes of the receptacles, tubes and panels
Determine the sizes and ampacity of wires, cables and circuit protectors.
3 watts per square foot – for general purpose circuit (lighting and
receptacles) or 24watts per 1 sq. m for lighting, 100 watts per outlet
A nominal value of 1500 watts for each 20- ampere small appliances and
laundry circuit.
Plus major appliances, (5000 watts for aircon) then get the total load.
Electricity (Basic Principles of Good
Wiring )
Before beginning any electrical repair, shut off the power.
(Remove the fuse or trip the breaker for the circuit you will be working on in
your service panel)
Prepare and study the wiring diagram. This will help you understand
the basic principles of good wiring.
Electrical wires are color coded to prevent wiring errors.
Black is HOT wire
White is Neutral wire
Green is Ground wire
Red is second HOT wire
Yellow is Traveller wire
Electricity (Basic Principles of Good
Wiring )
Always use appropriate size of wires
Sizes of wires (As the Number increases the actual size decreases)
Measured in terms of AWG (American Wire Gauge)
# 14 AWG (2.0mm2) – for lighting fixtures
# 12 AWG (3.5mm2) – for convenience outlets
# 10 or 8 AWG (5.5 to 8.5mm2)– for service entrance
Electricity (Basic Principles of Good
Wiring )
Sizes of wires (As the Number increases the actual size decreases)
Electricity (Basic Principles of Good
Wiring )
Sizes of wires (As the Number increases the actual size decreases)
Electricity (Test Instruments )
Ohm meter – test for resistance
Ammeter – test for current
Voltmeter – test for voltage
Multimeter/ VOM
Electricity (Word Problem)
15 ohm and 13 ohm resistor is connected in series and will be called
“X”. Another is a 23 ohms and 5 ohms is connected in parallel which
will be called “Y”. What will be the total current of the whole circuit if
“X” and “Y” is connected in parallel and the voltage is 24V?
Electricity (Word Problem)
A 4 Ohm resistor is connected in parallel to 3 series connected
resistors of 4, 3 and 5 Ohms, what will be the voltage of the circuit if
the Current is 8.3A?
Electricity (Word Problem)
A 3 resistors is connected in parallel namely 3.7, 9.4 and 12.7 Ohms
is connected in a series to a 2 parallel connected resistors of 11.6
and and 7.3 Ohms, what will be the voltage of the circuit if the
Current is 12.3A?
Electronics
Electronics
Electronics – refers to the flow of charge (moving electrons) through
nonmetal conductors (mainly semiconductors).
The flow of charge through various materials and devices such as,
semiconductors, resistors, inductors, capacitors, and vacuum tubes.
Electronics
Electronic components -It refers to any physical entity in an electronic
system whose intention is to affect the electrons in a desired manner
consistent with the intended function of the electronic system
Electronic circuit – composed of different components that are classified as
active and passive components.
Passive – components that do not generate voltage but controls the current
in a circuit.
Ex. Resistors, capacitors, inductors, etc.
Active – components that can generate, amplify and even control voltage
and current in a circuit.
Ex. Diode, transistor, integrated circuits (IC), etc.
Electronics
Semiconductors – a group that are neither good conductors nor good
insulators
Inductors – the choke or coil in a circuit that oppose changes in electric
current.
Resistor – a device that opposes the flow of electric current, it lowers the
voltage. It is non-polarized.
Capacitor - is a passive two-terminal electrical component used to store
energy in an electric field.
Electrical Circuit – a network that has a closed loop, allowing the complete
flow of current.
Conductors – are metals and other substances where electrons can move
freely
Insulators – substances where electrons cannot move freely.
Transformer – is an electronic devised used in producing desired voltage.
Electronics
Semiconductors – a group that are neither good conductors nor good
insulators
Inductors – the choke or coil in a circuit that oppose changes in electric
current.
Resistor – a device that opposes the flow of electric current, it lowers the
voltage. It is polarized.
Capacitor - is a passive two-terminal electrical component used to store
energy in an electric field.
Electrical Circuit – a network that has a closed loop, allowing the complete
flow of current.
Conductors – are metals and other substances where electrons can move
freely
Insulators – substances where electrons cannot move freely.
Transformer – is an electronic devised used in producing desired voltage.
Electronics (Tools)
Electric Drill and Drill Bits - in the range of 1/8 inch to 1/2 inch will come in
handy when you need to drill holes.
Soldering Iron - a 20 Watt to 30 Watt soldering iron with tips of 1/8 inch to
1/2 inch can be used for soldering of through hole components.
Disordering Pump - A pump aids in the removal of the liquid solder.
Wire stripper - is used to strip off wire insulator from its conductor before it
is used to connect to another wire.
Long nose Pliers – a 4-inch long nose pliers used to hold components that
have short leads that need to be soldered onto the PCB.
Side-Cutting Pliers - 4-inch side cutting pliers used to trim off excess
component leads on the printed circuit board and to cut wires before being
used.
Small tweezers - is used to hold small components.
Allen Wrench - set is used to unscrew or screw Allen type of screws.
Philips/Flat Head Screwdrivers
Socket wrench - sets that include nut drivers, hex drivers.
Electronics (Tools)
Maintenance
Tinning – the process of cleaning and applying a thin coat of solder on the
tip of the pre-heat soldering iron.
Flux – chemical cleaning agent, The purpose of flux is to clean oxides from
metal surfaces to ensure a clean bond in soldering.
Maintenance Tips of Electronic Tools
Ensure that the tools are used only for their intended purposes.
Keep them lubricated with a light film of oil to inhibit rust.
Keep the tools clean and sharp; keep the soldering tips clean and well tinned.
Ensure that proper uses of the tools are always adhered to by following the
instructions of using the tools.
Electronics (Components)
Electronic Components
It is a basic electronic element usually packaged in a discrete form, intended
to be connected together, usually by soldering to a printed circuit board, to
create an electronic circuit with a particular function (for example an
amplifier, radio receiver, or oscillator).
Electronics (Capacitors)
Capacitor
is a passive electronic component consisting of a pair of conductors
separated by a dielectric.
It stores and discharge electrical energy.
The voltage rating found in a capacitor is called working voltage.
The rating is expressed in capacitance; the unit of measurement in
capacitance is farad.
– invented by Ewald Georg von Kleist (October 1745)
Electronics (Capacitors)
Types of Capacitor
Electrolytic Capacitor (Electrochemical Type Capacitor)
Tantalum Capacitor
Ceramic Capacitor
Polystyrene Film Capacitor
Mica Capacitor
Metalized Polyester Capacitor
Variable Capacitor
Trimmer Capacitor
Electronics (Diodes)
It converts AC to DC.
It is a device that conducts current to flow in only one direction.
They are called rectifiers
It is polarized, the terminals are anode (positive) and cathode (negative)
Forward biased – when current is applied to the cathode (negative), it
permits the flow of current. (ON switch)
Reverse biased – when current is applied to the anode (positive), it will not
permit the flow of current. (OFF switch)
Zener diode – used as voltage reference, connected across a circuit where
regulated voltage is required; acts as a regulator
Light emitting diode (LED) – it acts like rectifier diode except that is usually
intended to indicate flow of current.
Photo diode – a diode which is sensitive to light; a light sensitive diode.
Electronics (Transistors)
Is an active semiconductor device having 3 electrodes. It could perform a
variety of applications such as switch, amplifier, and rectifier.
The terminals of a transistor are base, collector and emitter.
BASE - which is the lead responsible for activating the transistor.
COLLECTOR - which is the positive lead.
EMITTER - which is the negative lead.
Kinds of Transistor
NPN – arrow pointing outward;
The arrow points where negative is; supply is connected to the emitter and
collector.
Electronics (Resistors)
Is a device that opposes the flow of electric current, it lowers the voltage.
The simplest components in any circuit. Their job is to restrict the flow of
electrons and reduce the current or voltage flowing by converting electrical
energy into heat.
Variable resistors (also known as potentiometers) have a dial control on
them so they change the amount of resistance when you turn them.
Electronics (Resistors)
Electronics (Resistors)
2 4 x 10 = 240Ohms +-5%
Let’s Try
Bad Beer Rots Our Young Guts But Vodka Goes Well
Bad Beer Rots Our Young Guts But Vodka Goes
Well
Let’s Try