Professional Documents
Culture Documents
Chequered Plate
Chequered Plate
(A)--LOADING CALCULATION:
Moment of Inertia
Section Modulus
fb > fs
HENCE SAFE
(D) --CHECK FOR DEFLECTION:
Actual Deflection
= (( 5 x 3.314 x 1.12^4 ) 10^9 / ( 384 x 200000 x
= (( 5 x W x B^4 ) / ( 384 x E x I )) mm δ 0.064
5333.333 ))
δa > δ
HENCE SAFE
INPUT DATA FOR CHEQUERED PLATE DESIGN :
(A)--LOADING CALCULATION:
Moment of Inertia
Section Modulus
fb > fs
HENCE SAFE
Note:
1. The Chequered plate is designed for 500kg, whereas rest of the equipments loads shall be load on Main & Secondary
Beams
2. The seismic & Wind loads are taken care by the column & beams
(D) --CHECK FOR DEFLECTION:
Actual Deflection
δa > δ
HENCE SAFE
Case:2 Upper Floors "Reduced the width from 1.230 to 0.615m inorder to satisfy the 6mm thick"
Sl.No Description Unit Symbol Values
1 Maximum Width of Plate (Stiffener angle shall be added at the mid) m B 0.615
(A)--LOADING CALCULATION:
Moment of Inertia
Section Modulus
fb > fs
HENCE SAFE
Note:
1. The Chequered plate is designed for 500kg, whereas rest of the equipments loads shall be load on Main & Secondary
Beams
2. The seismic & Wind loads are taken care by the column & beams
(D) --CHECK FOR DEFLECTION:
Actual Deflection
δa > δ
HENCE SAFE
INPUT DATA FOR CHEQUERED PLATE DESIGN :
Case:2 Staitways
Sl.No Description Unit Symbol Values
(A)--LOADING CALCULATION:
Moment of Inertia
Section Modulus
fb > fs
HENCE SAFE
(D) --CHECK FOR DEFLECTION:
Actual Deflection
= (( 5 x 5.628 x 1.5^4 ) 10^9 / ( 384 x 200000 x
= (( 5 x W x B^4 ) / ( 384 x E x I )) mm δ 0.043
42666.667 ))
Allowable Deflection (As per BS 5950-1:2000 Table 8)
δa > δ
HENCE SAFE
LARSEN & TOUBRO LIMITED
ECC Division - EDRC
DESIGNED CHECKED
Title : Wind Pressure & Sag Tension Calculcaion Sheet OF 3
ARA SMP
Wind Speed for Insulator/Tower body as per MOM Dated 26.05.01 in KMPH 160 = 44.44 in m/sec
Basis Span for Sag Tension calculation as per Schedule C2 in M (L) = 450
As per DIN VDE 0210 and their further clarification dated 24.11.95, the dynamic wind pressure (q) in Table 5 of DIN VDE 0210 is arrived for
a basic wind speed of 120 Kmph. Hence for a wind speed of 150 Kmph, the dynamic wind pressure in Table 5 is to be multiplied by a factor
= (150 / 120 )^2 = 1.563 in wind pressure calculation for Conductor/ Earthwire & with a factor =(160/120)^2 = 1.778 for Insulator/ Towerbody.
Wind Load on Conductor/Groundwire as per Clause 8.1.2.1 of DIN VDE 0210 = Cf x q x d x ( 80 +0.6 x L)
Drag Coefficient for Conductor Diameter more than 15.80 mm refer Table 6 of DIN VDE 0210 Cfc = 1.00 1.00
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qc = 0.53 0.68
Dynamic Wind Pressure for 160 KMPH in Kg/m2 = ( Cfc * qc * ( 160 / 120 )^2 * 1000 / 9.81 ) = 96.047
Dynamic Wind Pressure for 150 KMPH in Kg/m2 = ( Cfc * qc * ( 150 / 120 )^2 * 1000 / 9.81 ) = 108.308
Drag Coefficient for Earthwire Diameter more than 15.80 mm refer Table 6 of DIN VDE 0210 Cfe = 1.00
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qe = 0.68
Dynamic Wind Pressure for 150 KMPH in Kg/m2 = ( Cfe * qe * ( 150 / 120 )^2 * 1000 / 9.81 ) = 108.308
Diameter of earthwire in mm 18.600 Drag Coefficient for Aerial warning balls 0.4
= 21.922
Total wind pressure on the earth wire including the effect = ( 84.24 + 21.922)
LARSEN & TOUBRO LIMITED
ECC Division - EDRC
DESIGNED CHECKED
Title : Wind Pressure & Sag Tension Calculcaion Sheet OF 3
ARA SMP
of warning sphere in Kg/m2 For 450 M Span = 106.162 (For Sag Tension Calculation)
Equivalent unit weight of earthwire in Kg/m = ( 0.818 + 7.2 / 30 + 0.52 / 450 ) 1.059
Drag Coefficient for Insulator as per Table 6 of DIN VDE 0210 Cfi = 1.20 1.20
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qi = 0.7 0.9
Wind Pressure on insulator for 160 KMPH in Kg/m2 = ( Cfi * qi * ( 160 / 120 )^2 * 1000 / 9.81 ) = 152.226 195.719
Drag Coefficient Cf is given in the Table 6 of DIN VDE 0210 for Square & rectangular towers Cft = 2.80 2.80
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qt = 0.7 0.9
Wind Pressure on Tower Body for 160 KMPH in Kg/m2 = ( Cft * qt * ( 160 / 120 )^2 * 1000 / 9.81 ) = 355.193 456.677
(VIII) Wind Pressure On Tower Body in Kg/m2 ( For Diagonal Wind condition ) : -
Drag Coefficient Cf is given in the Table 6 of DIN VDE 0210 for Square & rectangular towers Cft = 2.80 2.80
As per Cl.no 8.2.1.2 aerodynamical drag coefficient is to be increased by 10 % = (Cfdw = 2.8+10/100 * 2.8) = 3.08 3.08
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qdw = 0.7 0.9
DESIGNED CHECKED
Title : Wind Pressure & Sag Tension Calculcaion Sheet OF 3
ARA SMP
Wind Pressure tower in Kg/m2 (In Trans. & Long.Face) = Cfdw*qdw*( 160/120 )^2 *1000/9.81*Cos(45) = 276.275 355.211
1 35° & Nil wind 0 1126.00 16.006 6.137 1834.30 ($) 14.614 6.091
3 80° & Nil wind 0 995.70 ($) 18.100 6.940 1645.29 16.292 6.791
4 40° & Nil wind 0 1109.2 16.248 6.230 1810.49 14.806 6.171
DESIGNED CHECKED
Title : Wind Pressure & Sag Tension Calculcaion Sheet OF 3
ARA SMP
Designed Checked
Wind Pressure & Sag Tension Calculcaion
Title : Sheet OF 3
(For 220 kv Lines)
Ara Smp
Basis Span for Sag Tension calculation as per Schedule C2 in M (L) = 450
As per DIN VDE 0210 and their further clarification dated 24.11.95, the dynamic wind pressure (q) in Table 5 of DIN VDE 0210 is arrived for
a basic wind speed of 120 Kmph. Hence for a wind speed of 160 Kmph, the dynamic wind pressure in Table 5 is to be multiplied by a factor
= (160 / 120 )^2 = 1.778 in wind pressure calculation for Conductor,Earthwire,Insulator &Towerbody.
Wind Load on Conductor/Groundwire as per Clause 8.1.2.1 of DIN VDE 0210 = Cf x q x d x ( 80 +0.6 x L)
Drag Coefficient for Conductor Diameter more than 15.80 mm refer Table 6 of DIN VDE 0210 Cfc = 1.00
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qc = 0.53
Dynamic Wind Pressure for 160 KMPH in Kg/m2 = ( Cfc * qc * ( 160 / 120 )^2 * 1000 / 9.81 ) = 96.047
Dynamic Wind Pressure for 160 KMPH in Kg/m2 = ( Cfc * qc * ( 160 / 120 )^2 * 1000 / 9.81 ) =
Drag Coefficient for Earthwire Diameter more than 15.80 mm refer Table 6 of DIN VDE 0210 Cfe = 1.00
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qe = 0.68
Dynamic Wind Pressure for 160 KMPH in Kg/m2 = ( Cfe * qe * ( 160 / 120 )^2 * 1000 / 9.81 ) = 123.230
Diameter of earthwire in mm 18.600 Drag Coefficient for Aerial warning balls 0.4
= 25.027
Total wind pressure on the earth wire including the effect = ( 95.846 + 25.027)
LARSEN & TOUBRO LIMITED
ECC DIVISION - EDRC
Designed Checked
Wind Pressure & Sag Tension Calculcaion
Title : Sheet OF 3
(For 220 kv Lines)
Ara Smp
Equivalent unit weight of earthwire in Kg/m = ( 0.818 + 7.2 / 30 + 0.52 / 450 ) 1.059
Drag Coefficient for Insulator as per Table 6 of DIN VDE 0210 Cfi = 1.20
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qi = 0.7
Wind Pressure on insulator for 160 KMPH in Kg/m2 = ( Cfi * qi * ( 160 / 120 )^2 * 1000 / 9.81 ) = 152.226
Drag Coefficient Cf is given in the Table 6 of DIN VDE 0210 for Square & rectangular towers Cft = 2.80
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qt = 0.7
Wind Pressure on Tower Body for 160 KMPH in Kg/m2 = ( Cft * qt * ( 160 / 120 )^2 * 1000 / 9.81 ) = 355.193
(VIII) Wind Pressure On Tower Body in Kg/m2 ( For Diagonal Wind condition ) : -
Drag Coefficient Cf is given in the Table 6 of DIN VDE 0210 for Square & rectangular towers Cft = 2.80
As per Cl.no 8.2.1.2 aerodynamical drag coefficient is to be increased by 10 % = (Cfdw = 2.8+10/100 * 2.8) = 3.08
Dynamic Wind Pressure As Per Table - 5 of DIN VDE 0210 in Kn/m2 for 120 KMPH qdw = 0.7
LARSEN & TOUBRO LIMITED
ECC DIVISION - EDRC
Designed Checked
Wind Pressure & Sag Tension Calculcaion
Title : Sheet OF 3
(For 220 kv Lines)
Ara Smp
Wind Pressure tower in Kg/m2 (In Trans. & Long.Face) = Cfdw*qdw*( 160/120 )^2 *1000/9.81*Cos(45) = 276.275
1 35° & Nil wind 0 1798.20 ($) 15.865 5.556 1770.30 15.142
5° - Full wind
8 (For groundwire 120.873 ---- ---- ---- 3836.21 ($) 16.397
more than 40 m)
LARSEN & TOUBRO LIMITED
ECC DIVISION - EDRC
Designed Checked
Wind Pressure & Sag Tension Calculcaion
Title : Sheet OF 3
(For 220 kv Lines)
Ara Smp
5° - Diagonal wind
9 (For groundwire 96.698 ---- ---- ---- 3341.61 15.817
more than 40 m)
Date : 27/07/2001
Sheet OF 3
11.95, the dynamic wind pressure (q) in Table 5 of DIN VDE 0210 is arrived for
40-100m
1.00
0.68
123.230
95.846
40-100m
1.00
0.68
123.230
95.846
N & TOUBRO LIMITED
ECC DIVISION - EDRC
Date : 27/07/2001
Sheet OF 3
40-100m
1.20
0.9
195.719
40-100m
2.80
0.9
456.677
40-100m
2.80
3.08
0.9
N & TOUBRO LIMITED
ECC DIVISION - EDRC
Date : 27/07/2001
Sheet OF 3
45
355.211
GROUND WIRE
32 Fibres
18.600
(* *) 1.059
11173
194.08
17.3 x 10-6
10227
5°C
35°C
80°C
Factor
of
Safety
6.311
6.698
6.996
----
----
----
----
2.913
N & TOUBRO LIMITED
ECC DIVISION - EDRC
Date : 27/07/2001
Sheet OF 3
3.344