Professional Documents
Culture Documents
TUBE WELL
CHAPTER : S-4
Chapter Description Unit Rate
Code No.
4.1 Construction of tube-well from ground level and upto 100 Meter depth and
above sizes in all types of soils in alluvium strata by “bailing” method and
without gravel packing as per IS: 2800 (Part - I& II) 1979 specifications
(The work includes formation of
4.2 Construction of Tube-well upto 100 Meter depth and above in all type of
rocks by DTH system and over burden, to accommodate casing pipe of
following sizes in all types of soils and over burden including lowering of
4.2.1 100 mm dia Nominal bore. R.Mtr. 524.00
casing pipes, but excluding cost of casi
4.3 Construction of tube-well from ground levels and upto 100 Meter depth
and above to accommodate housing and assembly pipe of following sizes
in all types of alluvium strata by percussion/ rotary drilling method and with
4.3.1 150 mm Nominal bore. R Mtr. 1278.00
gravel as per IS:4097-1967 and packi
4.4 Development of tube well as per IS specification using suitable Hr. 718.00
4.5 compressor
Supply of ERW to give
M.S.sand
blackfree water
casing for ISI
pipe required
markedyield of the gravelofpacked
(IS:4270/1992) grade
tube
Fe410well.
of following sizes at site of work.
C. Code Nominal bore of pipe (mm) Outside Thickness of Mass of Unit Proposed
No. dia of Pipe (mm) plane Rate
Pipe tube
(mm) (kg.\m)
4.5.1 100 114.3 5 13.48 Mtr. 791
S-4 Page 1
CHAPTER : S-4
Chapter Description Unit Rate
Code No.
4.6 Supply of strainer pipes made of ERW M.S. black pipe ISI mark of
following sizes at the site of work including required size of slotting as per
IS:8110-1985.
4.6.1 150 mm Nominal Bore. Mtr. 1460.00
4.7 Testing verticality of tube-well by plumbing system and yield test and draw Each 9979.00
down test by pumping system as per IS: 2800 (Part II) 1979.
4.8 S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts
4.8.1 complete
100mm diafor casing size: Each 245.00
4.9 S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for Each 350.00
holding the riser pipe assembly of submersible pump set.
4.1 Supply of 50mm dia G.I. medium class pipe(each length 5.8 m to 6.0m) Each 15711.00
tripod as per drawing and design with chain pulley of. 3MT capacity
4.11 Installation of submersible motor pump set in Tube-well/open well 4888.00
complete ( labour charges only) including transportation of tripod, chain Each
pulley block & any other material required for lowering purpose.
4.12 P & F 60 cm. wide M.S. ladder in open well made of flat iron 32×5mm and Mtr. 297.00
10mm dia bars @ 200mm c/c with angle iron hold fasts at suitable interval
complete as per drawing.
4.13.1 Installation of India mark II hand pump set, complete on existing plate Each 1222.00
form.
4.13.2 Construction of 185 cm. dia platform as per approved design and Each 3841.00
drawing of UNICEF.
4.14 Supplying of India mark II hand pump set complete ISI marked with Each 11347.00
cylinder and ten connecting rods etc. ISI
4.15 Supplying and installation of 32 mm dia G.I. pipe medium class ISI marked Mtr. 307.00
in 3m length including all accessories and fittings required for installation of
hand pump.
4.16 Supplying and installation of submersible pumping motor pump sets I.S.I.
Marked (IS : 8034-1989 ) of approved make like K.S.B., KIRLOSKAR,
Calama etc. or equivalent, making connection suitable for
4.17 For item of earthingwell.
T.W./D.C.B./Open refer to Electrical
The BSR
job includes .
screwing and weldi
4.19 Item of panel board if required shall be as per design and specification
approved by the Engineer In-charge as per the requirement.
4.2 Providing & lowering of G.I. Pipes, flange pipe including rubber washer
and nuts of 8 mm dia complete in all respect I.S.I. Make.
S-4 Page 2
CHAPTER : S-4
Chapter Description Unit Rate
Code No.
4.20.1 B Class 50 mm dia R. Mtr. 343.00
4.21 Un-lowering of submersible pump set with all piping from a tube-well/ Each 6110.00
open-well complete (labour charge only ) including transportation of tripod, Job
chain, pulley-block and other materials required and lowering of repaired/
4.22 new pump in the
Construction of tube-well
Recharge/ open
Shaft in filter pit including Earth work
4.22.1 Excavation
Diameter 900, lifting
mm excavted earth with all lift and 50 m lead and centering Rm 242.00
4.22.2 & shuttering evenever
Diameter 750 mm required. Rm 212.00
4.23 Supply & fixing Pre-cast RCC Rinngs at the mouth of recharge shaft of
4.23.1 M20 mix with
Diameter 40 mm thickness
900 mm Rm 696.00
4.23.2 Diameter 750 mm Rm 605.00
4.24 Supply & lowering air line of 25mm dia, G.I. pipe 'B' class having Rm 273.00
perforation 3 to 5mm size all arrow of G.I. pipe in Zig-Zag fashion &
4.25 making air vent
Supply and at topvent
lowering including the63mm
air pipe cost ofdia
Tee-Nipples, Elbow, Socket
rigid PVC pipe(IS 4985) mark etc. Rm 140.00
class II (4kg per cm2 ) with required all necessary fittings including
4.26 perforation
Supply & lyingof 3River-gravels
to 5 mm sizeofallfollowing
around the pipe
sizes at a distance
in recharge shaft,offilter
180 pit
to
4.26.1 220mm
after in zig
Size 9screening zag fashion and making ai
to 12 mm& washing from kachha shift without deduction of voids Cum 1815.00
4.26.2 Size 3 to 5 mm Cum 2662.00
4.27 Supply & laying of clean, clear sharp river sand of size 1 to 2mm coarse, Cum 3388.00
without deduction of voids.
S-4 Page 3
CHAPTER S-3
DRAINAGE / DISPOSAL WORKS
CHAPTER S-3
Chapter Description Unit Rate
Code No.
Note:-
1 If grade `AA S.W. pipes (IS:651 mark) are used then add 5%
S-3 Page 4
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.9 P & F Sand-cast Iron (S.C.I.) Pipe (IS : 1729mark) of approved make in
wall or in floor with M.S. holder bat clamps in 10 X 10 X 10 Cm. M-15
grade concrete blocks, joints filled with CM 1:4 with spun yarn including .
cutting holes and making good the wall:
3.9.1 50mm dia P.Rmt. 441.00
3.9.2 75mm dia P.Rmt. 477.00
3.9.3 100mm dia P.Rmt. 549.00
3.9.4 150mm dia P.Rmt. 1037.00
S-3 Page 5
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.1 Add extra for Lead caulked joints (IS:782-1978) in sand cast iron
pipes/spun
3.11 P & F SCI Fittings (IS : 1729 mark) in CM 1:4 with spun yarn
S-3 Page 6
CHAPTER S-3
Chapter Description Unit Rate
Code No.
Each 121.00
3.15 Making connection with existing G.I. pipe lines of all sizes
Each 89.00
ASBESTOS CEMENT (A.C.) SOIL VENT & RAIN WATER PIPES
3.16 P & F on wall face A.C. pipes (IS : 1626 part-I mark) of approved make
with wooden plugs and M.S. clamps, jointing with spun soaked in
bitumen and CM 1:2 complete including making good the wall
3.17 P & F A.C. fittings (IS : 1626 part-I mark) of approved quality / make
with spun yarn socked in bitumen & CM 1:2
3.17.1 50mm
Cowel Each 31.00
Socket Each 13.00
Offset Each 37.00
Shoe Each 22.00
With door bend Each 37.00
With door Tee Each 47.00
Without door bend Each 31.00
Without door Tee Each 34.00
3.17.2 75mm
Cowel Each 37.00
Socket Each 14.00
Offset Each 44.00
Shoe Each 25.00
With door bend Each 44.00
With door Tee Each 52.00
Without door bend Each 35.00
Without door Tee Each 35.00
3.17.3 100mm
Cowel Each 44.00
Socket Each 15.00
Offset Each 61.00
Shoe Each 29.00
With door bend Each 52.00
With door Tee Each 58.00
Without door bend Each 39.00
Without door Tee Each 47.00
3.17.4 150mm
Cowel Each 58.00
S-3 Page 7
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.18 Labour charges for removing CI/AC pipes of all sizes including
accessories with care and stacking of useful material
P.Rmt. 7.00
RIGID PVC SOIL, WASTE & RAIN WATER (SWR) PIPES
3.19 P & F rigid pvc pipe (IS:4985 mark) class II/ (4 kg./cm2) approved
quality / make including joining the pipe with solvent cement rubber ring
and lubricant
3.2 P & F rigid pvc pipe fittings (IS : 4985 mark) of approved quality / make
including joining the pipe with solvent cement rubber ring and
lubricant :
3.20.1 Coupler (Socket)
75mm dia Each 74.00
110mm dia Each 90.00
S-3 Page 8
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.20.8 Bend 45
75mm dia Each 68.00
110mm dia Each 108.00
S-3 Page 9
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.20.23 P- Trap
110mm dia Each 323.00
3.20.24 Q- Trap
110mm dia Each 360.00
3.20.25 S- Trap
110mm dia Each 450.00
3.21 Construction of manhole in all type of soil inner size 90 X 60 Cm. 450
mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in
foundation, 20 mm thick inside plaster in CM 1:6, finished with floating
neat cement, 50mm thick M-15 grade C.C. floo
3.21.2 Add extra over item 3.21.1 for every additional 0.10m depth above
Each 161.00
0.5m depth
3.22 Construction of Man hole, in all types of soil, inner size 1.5 x 1.2 M,
with 450mm thick masonry in CM 1:6, 10 Cm. thick cement concrete
1:5:10 in foundation, 20mm thick inside plaster in CM 1:6, finished with
floating neat cement, 50 mm thick M-15 grade
3.23 Construction of chamber in all type of soil with 300 mm thick masonry
in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider
plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15
grade C.C. flooring , earthwork etc. complet
3.23.1 Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame.
Each 2311.00
3.23.2 Inside size 450 X 450 mm depth upto 0.5 M Cement cover with frame.
Each 3209.00
3.23.3 Inside size 600 X 450 mm depth upto 0.5 M Cement cover with frame.
Each 4205.00
S-3 Page 10
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.24 Construction of soakage well in all type of soil with 300 mm thick dry
masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone
slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15
grade C.C flooring , earthwork complete as per
3.24.1 Size 300 cm. dia outside & 300 Cm. depth Each 20385.00
3.24.2 -do- & 240 cm depth Each 16307.00
3.24.3 Size 240 cm. dia outside & 240 Cm. depth Each 13987.00
3.25 Construction of soakage Trench in all types of soil with 300 mm thick
dry stone masonry, 80 mm thick stone slab covering, jointing of slab in
CM 1:3 Ralthal, Kharanja, 40 mm thick M-15grade C.C. flooring
earthwork etc. complete as per approved drawing
3.25.1 Top width 180Cm., bottom width 90Cm. & depth 240Cm. Each 4543.00
3.25.2 Top width 240Cm., bottom width 150Cm. & depth 300Cm. Each 12775.00
3.27 Labour charges for construction of Soakage well of 90 Cm. dia (Earth –
work & its disposal ,with in a lead of 0.5 Km .only ).
P.Rmt. 64.00
3.28 Add extra if Soakage Well is filled with dry stones. Each 523.00
S-3 Page 11
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.3 Emptying of Septic tank ,Soakage well etc. by disposing or sludge upto
5 Km. lead & taking out sewage including cleaning of site.
Nagar Parishad / Tanker cost Rs. 800/- per Tanker for 3.50 cum
including contractor profit
Each 330.00
3.31 Add extra if R.C.C slab of designed thickness & reinforcement is
provided on manhole in place of stone slab( Actual area of R.C.C slab
to be measured).
P.Sqm 187.00
3.32 P & F M.S. Foot Rests in with C.M.,1:3, standard design in 20mm
square M.S. bar 50 mm embedded in wall & 10 cms. projected out
complete.
Each 173.00
3.33 Supplying and fixing C.I. Cover with frame, C.I. gratings for chambers &
man holes.
P.Kg. 44.00
3.34 Supplying and fixing Ferro- cement cover with C.I. frame for
chambers & man holes of size.
3.34.1 450mm dia, 5Kg. C.I. frame to with stand 3 MT center point load &
minimum unfractured load of 1 MT. (Light duty).
Each 950.00
3.34.2 500mm dia 12 Kg.-do-15 MT centre point load (medium duty).
Each 1484.00
3.34.3 500mm dia 22 Kg.-do-22 MT centre point load (Heavy duty).
Each 1986.00
3.34.4 500mm dia 25 Kg.-do-70 MT centre point load seal type (Heavy duty.)
Each 3041.00
3.34.5 Rectangular shape 600 x 450 mm, to withstand 3 MT center point
load & minimum unfractured load of 1 MT. (Light duty).
Each 1150.00
3.35 Supplying & Fixing R.C.C. Manholes covers with frame of approved
make (Light duty).
3.35.1 Size 500mm dia (Double seal) Each 311.00
3.35.2 Size 450 mm Each 276.00
3.35.3 Size 400 mm Each 208.00
3.35.4 Size 600 x 600mm (Double seal) Each 475.00
3.35.5 Size 600 x 450 mm Each 401.00
3.35.6 Size 450 x 450 mm Each 302.00
3.35.7 Size 300 x 300 mm Each 95.00
3.35.8 Size 250 x 250 mm Each 78.00
3.35.9 Size 180 x 180 mm Each 70.00
3.36 Construction of Open Surface Drain with 112mm thick brick masonry in
CM 1:4,110mm thick base concrete 1:5:10, 37mm thick M-15 grade
C.C. flooring ,12mm 1:4 cement plaster on all exposed faces of walls
including top surface excavation & disposal of earth
S-3 Page 12
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.37 Construction of open Drain with 112mm thick brick masonry in CM 1:4
Semi circular S.W. glazed channel (confirming to IS Standards) fixed
with cement mortar 1:1 over a bed of 100mm thick C.C. 1:5:10, filling of
edged with M-15 grade C.C. flooring, 12mm cem
3.37.3 250 mm drain,225mm Av. depth width 250 Cm S.W. glazed channel.
P.Rmt. 1163.00
3.38 Extra For additional 5 Cm. Average depth of drain of all sizes.
P.Rmt. 71.00
3.39 P & F precast dense cement concrete (Vibro-pressed) drain section
Block of different size as per approved drawing and design and
strength as per IS code 2185 part I of grade 'D' (5.00mm2) proper
quality of additive/admixture like plasticizer etc. added to
SPUN - CENTRIFUGALLY CAST IRON SOIL WATER & RAIN WATER PIPES :-
S-3 Page 13
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.41 Providing & fixing Spun - Centrifugally cast Iron Pipes (IS : 3989 Mark)
of approved make in wall or in floor with M.S. Holder bat clamps in 10 x
10 x 10 Cm. M-15 Grade concrete blocks, joints filled with CM 1:4 with
spun yarn including cutting holes and
S-3 Page 14
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.43 Providing and Fixing Spun - Cast Iron floor trap (Nahani) of (IS : 3989
Mark) approved quality / make with socket down or hinged grating
including cutting and making good the floor :-
3.43.1 Size 100 x 100 mm Each 818.00
3.43.2 Size 100 x 75 mm Each 771.00
3.44 Add 10% extra over item 3.41 if the pipes are laid under suspended
condition under the roof
3.45 Providing and fixing unplasticized poly vinyl chloride (UPVC) SWR
pipes Type B for sciland waste discharge system (IS:13592 : 1992
Marked) of approved quality / make)
3.46 Providing and fixing unplasticized poly vinyl chloride (UPVC) SWR
pipes Type B for sciland waste discharge system (IS:13592 : 1992
Marked) of approved quality / make)
3.46.1 Coupler
75mm dia Each 72.00
110mm dia Each 112.00
S-3 Page 15
CHAPTER S-3
Chapter Description Unit Rate
Code No.
S-3 Page 16
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.48 Providing & fixing Spun –Centrifugally cast Iron Pipes fitting (IS : 3989
Mark ) in CM 1:4 with spun Yarn 100mm w/o door as per direction of
Engineer-in-Charge.
(a) P Trap of standard size Each 936.00
(b) Long P Trap (900mm) Each 2668.00
(c) Long P Bend Each 922.00
(d) Long Floor Trap (600mm) Each 1655.00
3.49 Removing & Re fixing of S.C.I. Pipe and Spun Pipe with C.I.clip as per
direction of Engineer-in-Charge of following diameters :-
(a) 100mm dia Each 165.00
(b) 150mm dia Each 145.00
3.51 Cleaning of C.I. Pipe Line of various sizse as per requirement at site of
different sizes including 100mm,150mm & 225mm dia of C.I.Pipes as Rmt 55.00
per direction of Engineer-in-Charge.
3.53 Providing & fixing Hubless Spun –Centrifugally cast Iron Pipes (IS :
15905 Mark ) of Approved make in wall or in floor with M.S. Holder bat
clamps in 10 X 10 X10 Cm. M-15 Grade concrete blocks, joints filled
with CM 1:4 with spun yarn including cutting ho
S-3 Page 17
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.54 Providing & fixing Hubless Spun –Centrifugally cast Iron Pipes fitting
(IS : 15905 Mark ) in CM 1:4 with spun Yarn.
3.54.1 75mm w/o door
(i) Offset (130mm) Each 511.00
(ii) Shielded (SS) Coupling (With EPDM Rubber) Each 418.00
(iii) D/Door Y-Tee Each 543.00
(iv) Bend Each 273.00
(v) Cowel Each 364.00
(vi) Tee Each 364.00
3.55 Mechanised Cleaning of sewer line of diameter upto 200mm with the
help of trolley mounted electrical driven machine having flexible steel
springs of length 20ft. Each which are rotated with the help of electric mtr 140.00
motor and clutch assembly.
3.56 Mechanised sewer line Cleaning upto diameter 100mm with the help of
PU coated glass fibre rod mounted on a wheel with brush attachment. mtr 97.00
S-3 Page 18
CHAPTER S-3
Chapter Description Unit Rate
Code No.
3.58 Suplying and Fixing Ductile iron Man Hole Covers/storm water grating
and gratingwith frame of various sizes weight and types and load
bearing capacity as per EN -124 ,superior quality or equivalent, Kg. 165.00
comlete as per Direction of Engineer In charge.
S-3 Page 19
CHAPTER : S-2
WATER SUPPLY INSTALLATION
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
GALVANISED IRON PIPES
2.1 a P & F G.I. pipes (Internal work) with G.I. fittings (IS:1239
Mark) & MS clamps including cutting and making good the
walls and floors :
Exposed on wall A B
2.1.1 15mm dia nominal bore Each 147.00 160.00
2.1.2 20mm dia nominal bore Each 192.00 205.00
2.1.3 25mm dia nominal bore Each 247.00 277.00
2.1.4 32mm dia nominal bore Each 310.00 351.00
2.1.5 40mm dia nominal bore Each 390.00 411.00
2.1.6 50mm dia nominal bore Each 471.00 540.00
2.1.7 65mm dia nominal bore Each 585.00 667.00
2.1.8 80mm dia nominal bore Each 726.00 859.00
2.1.9 15mm dia nominal bore Each 152.00 166.00
2.1.10 20mm dia nominal bore Each 194.00 208.00
2.4 Fixing water meter (IS:779 mark) and stop cock in GI pipe line
including making chamber of approved size excluding cost of
water meter & stop cock.
Each 220.00
2.5 P & F water meter (IS:779 mark) of approved make.
2.5.1 15mm dia Each 863.00
2.5.2 20mm dia Each 1575.00
2.5.3 25mm dia Each 2160.00
S-2 Page 20
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.6 P & F pillar cocks (IS:8934 mark) of superior quality and
approved make :
2.6.1 CP Pillar cock, 15mm dia nominal bore Each 733.00
2.6.2 CP Pillar cock Elbow action, 15mm nominal bore Each 853.00
2.6.3 CP Pillar cock fancy type, 15mm nominal bore Each 993.00
2.6.4 CP Pillar cock, Swan neck with casted spout, 15mm nominal 818.00
Each
bore
2.6.5 CP Pillar cock, high neck, 15mm nominal bore Each 759.00
2.6.6 Synthetic Material (PTMT) Pillar cock of approved 331.00
Each
quality/make-15, mm nominal bore
2.7 P & F Bib Cock (IS:8931 Mark)
Superior quality of approved make :
2.7.1 Brass 400 grm, 15mm nominal bore. Each 335.00
2.7.2 PVC heavy duty, 15mm nominal bore. Each 79.00
2.7.3 CP Brass bib cock, 15mm nominal bore. Each 619.00
2.7.4 CP Brass swan neck, 15mm nominal bore. Each 535.00
2.7.5 (-do-) long body, 15mm nominal bore weight not less than 690 677.00
Each
grm
2.7.6 (-do-) long nose, 15mm nominal bore weight not less than 852.00
Each
810 gm
2.7.7 (-do-) Elbow action, 15mm nominal bore Each 773.00
2.7.8 Synthetic Material (PTMT) bib cock of approved quality / 203.00
Each
make, nominal bore, 15mm 86 mm long
2.7.9 (-do-) Fancy Type, 122mm long Each 236.00
2.7.10 (-do-) long body, 175mm long Each 269.00
2.11 P & F Ball Cock (IS : 1703 Mark) with Rod & P.V.C. Ball
complete :
2.11.1 Brass wt.400 gm. 15mm Each 256.00
2.11.2 Brass wt.750 gm. 20mm Each 403.00
2.11.3 (-do-) wt.1000 gm. 25mm Each 436.00
2.11.4 (-do-) wt.1000 gm. 32mm Each 437.00
S-2 Page 21
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.11.5 (-do-) wt.1200 gm. 40mm Each 716.00
2.11.6 (-do-) wt.2000 gm. 50mm Each 743.00
2.11.7 Synthetic material (PTMT) of approved make 15mm nominal 233.00
Each
size.
2.11.8 (-do-) 20mm nominal size Each 321.00
2.11.9 (-do-) 25mm nominal size Each 658.00
2.11.10 (-do-) 50mm nominal size Each 1713.00
2.13.1 PVC pipe with C.P. Brass nuts upto length 300mm Each 48.00
2.13.2 (-do-) upto length 370mm Each 57.00
2.13.3 (-do-) 450mm Each 77.00
2.13.4 (-do-) 600mm Each 84.00
2.13.5 CP Brass pipe with CP Brass nuts upto length 300mm Each 66.00
2.13.6 (-do-) 370mm Each 84.00
2.13.7 (-do-) 450mm Each 103.00
2.13.8 (-do-) 600mm Each 139.00
2.14 P & F Flush Cock / Flush Valve (IS : 9758 Mark) For WC of
approved quality make.
2.14.1 CP brass push type 15mm nominal bore. Each 265.00
2.14.2 (-do-) 20mm nominal bore. Each 499.00
2.14.3 (-do-) exposed 25mm nominal bore. Each 926.00
2.14.4 (-do-) 32mm nominal bore. Each 1387.00
2.14.5 (-do-) concealed 25mm nominal bore. Each 999.00
2.14.6 (-do-) 32mm nominal bore. Each 1539.00
2.14.7 (-do-) Half-turn exposed 25mm nominal bore. Each 817.00
2.14.8 (-do-) concealed 25mm nominal bore. Each 958.00
2.14.9 Brass / Gun metal half-turn wt. 1 kg. of approved quality / 504.00
Each
make, 25mm nominal bore.
2.14.10 CP Brass flush valve 32mm nominal bore. Each 2223.00
S-2 Page 22
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.16.1 15mm nominal bore. Each 238.00
2.16.2 20mm nominal bore. Each 316.00
2.16.3 25mm nominal bore. Each 502.00
2.16.4 32mm nominal bore. Each 683.00
2.16.5 40mm nominal bore. Each 917.00
2.16.6 50mm nominal bore. Each 1282.00
2.17 P & F Flush valve (Hydraulic) with level complete (IS : 9758
Mark) of approved make :
2.17.1 32mm nominal bore. Each 2721.00
2.17.2 25mm nominal bore. Each 2362.00
S-2 Page 23
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.23 P & F Bidet (IS : 2556 Mark) of superior quality and approved
make with fittings :
2.23.1 CP brass bidet fittings without Pop up Each 3845.00
2.23.2 (-do-) with shower and Pop up waste Each 4529.00
2.24 P & F precast RCC water storage Tank with RCC cover 25mm
thick and 15cm. Long GI over-flow pipe including making
connections etc. & hoisting upto 1M. Ht. From ground level
having :
2.29.1. 233.00
1620 (20mm OD) pipe Each
2
2.29.1. 296.00
2025 (25mm OD) pipe Each
3
2.29.1. 396.00
2532 (32mm OD) pipe Each
4
2.29.1. 518.00
3240 (40mm OD) pipe Each
5
S-2 Page 24
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.3
Providing and fixing Polyethylene - Aluminimum -
Polyethylene (PE-AL-PE) Composite Pressure Pipes as per
15450 : 2004 U.V. stablised with carbon black having thermal
stabillity for hot and cold water supply with all compression
type composite internal sea
2.30.1. 229.00
1216 (16mm OD) pipe P.Rmt.
1
2.30.1. 266.00
1620 (20mm OD) pipe P.Rmt.
2
2.30.1. 324.00
2025 (25mm OD) pipe P.Rmt.
3
2.30.1. 423.00
2532 (32mm OD) pipe P.Rmt.
4
2.30.1. 536.00
3240 (40mm OD) pipe P.Rmt.
5
2.31
2.32 Supply & fixing G.I. Union ISI marked in G.I. pipe line as
required complete in all respect of size.
S-2 Page 25
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.33.4 Long body Bib Cock 15 mm nominal size Each 985.00
2.33.5 Two way Bib Cock 15 mm nominal size Each 1067.00
2.33.6 Angular stop cock with long thread 15 mm nominal size Each 693.00
2.33.7 Stop cock long thread Each 726.00
2.33.8 Stop cock with reduced body Each 924.00
2.33.9 Concealed stop cock 15 mm nominal size Each 1056.00
2.33.10 Sink cock with swinging casted spout (table mounted ) 15 mm 1474.00
Each
nominal size
2.33.11 Single lever wash basin mixer with 450 mm long copper 4235.00
Each
connection pipe
2.33.12 Central hole basin mixer Each 2453.00
2.33.13 Wall mixer 3 in 1 system with provision of tetephonic bath 3403.00
Each
shower with bend pipe
2.33.14 600 mm long towel rail Each 1637.00
2.33.15 Revolving type towel ring Each 1001.00
2.33.16 Soap dish Each 974.00
2.33.17 Double coat hook Each 748.00
2.33.18 190 mm rain shower Each 5075.00
2.33.19 Shower arm Each 1100.00
2.33.20 Paper holder Each 1023.00
2.33.21 Hand shower with 8 mm dia 1 mt long PVC tube & wall hook 1665.00
Each
complete
2.34
2.35
S-2 Page 26
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.36
Providing and fixing 3-layer PP-R (Polypropylene random
coplymer ) pipes SDR 7.4 UV stabilized and antimicrobial
fusion welded, having thermal stability for hot & cold water
supply including all PP-R plain & brass threaded
Polypropylene random fittings in
2.37
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)
pipes, having thermal stability for hot & cold water supply
including all CPVC plain & brass threaded fittings i/c fixing the
pipe with clamps at 1.00 m spacing. This includes jointing of
pipes &
2.38
2.39
S-2 Page 27
CHAPTER : S-2
Chapter Code Description Unit Rates
No.
2.39.5 40 mm nominal outer dia pipes Rm 329.00
2.39.6 50 mm nominal outer dia pipes Rm 529.00
2.4 Providing and fixing Premium quality Towel rack 600mm 2808.00
long 260mm wide with lower hangers CP Brass fittings of Each
approved make as per direction of Engineer-in-charge
2.41 Labour Charges for Removing & Refixing the water Storage 335.00
Tank of all sizes and including all Necessary fitting complete
Each
in all respect as per approved sample and direction of
engineer in charge.
2.42 Providing and fixing premium quality Angular stop cock with 1429.00
wall flange complete as per sample approved by Engineer in Each
charge
2.43 Providing and fixing premium quality Two way Bib cock with 2123.00
wall flange complete as per sample approved by Engineer in Each
charge
2.44.1 300 Lt. capacity Rate analysis for 1 No. Each 135.00
2.44.2 500 Lt. capacity Rate analysis for 1 No. Each 146.00
2.44.3 Above 500 Lt. capacity Rate analysis for 1 No. Each 157.00
2.45 Providing & fixing C.I. Saddle pieces 100mm dia with nut & 178.00
bolt & washer & Rubber Gasket complete as per direction of Each
engineer in charge
2.47 989.00
Providing Laying Jointing DI Pipe (Ductile iron pipe) of 100
mm dia ISI marked K-7 grade as per IS : 5329-2000 with
internal cement mortar lining for potable water with rubber Mtr
ring (EPDM/ SBR) Joints per IS : 5382-1985 complete
including Hydraulic t
S-2 Page 28
CHAPTER S-1
SANITARY INSTALLATION WORK
NOTE: All items which are manufactured ISI marked, shall only be used. this
condition shall be always incorporated in special condition of contract.
CHAPTER S-1
Chapter Description Unit Rate
Code No.
WATER CLOSETS
1.1 P. & F Squatting Pan (Indian type) white glazed vitreous china 1st
quality W.C. Pan (IS : 2556 Mark) with 100 mm vitreous china P or S
trap including cutting and making good the wall and floor (excluding the
pair of foot rest.)
1.1.1 Size 450mm. Each 1079.00
1.1.2 Size 510 mm Each 1123.00
1.1.3 Size 580mm Each 1169.00
1.2 P & F Indian type white glazed vitreous china 1st quality W.C. orissa
pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including
cutting and making good the wall and floor:
1.2.1 Size 530x410mm. Each 1719.00
1.2.2 Size 580x440mm. Each 1780.00
1.3 P & F WVC Foot- rest (IS : 2556 Mark) including cutting and making
good the floor size:
S-1 Page 29
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.9 P & F C.P. lugs for toilet seat cover. Pair 87.00
1.1 Labour charges for removing W.C. pan (any type) of all sizes with care
Each 115.00
including all necessary fittings P or S trap.
1.11 P & F White glazed Conversion Bend for W.C. from P trap to S trap.
Each 163.00
1.16 P & F W.V.C. Urinal Partition Plate of approved standard make of size
630x315mm including making good the wall.
Each 1040.00
1.17 P&F Marble Urinal Partition slab both sides polished of approved
design cut from marble size 900x600mm.
1.18 P & F W.V.C. Half-Round Channel of approved make in C.M. 1:3, joints
finished in white cement of:
1.18.1 Size 100mm dia. P.Rmt. 467.00
1.18.2 Size 150mm dia. P.Rmt. 664.00
1.19 P & F W.V.C. (IS: 2556 Mark) Squatting Urinal of standard make
complete. Including cutting & making good the floor:
1.19.1 Size 450x350mm Each 1275.00
1.2 Labour charges for removing and refixing of urinals (all type & sizes)
including all necessary fittings.
Each 165.00
S-1 Page 30
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.22 P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark).
Of approved make with complete fittings C.I. brackets duly painted,
brass ball cock with ball, (IS: 1703 mark) complete including cutting
and making good the wall:
1.22.1 WVC with C.P. brass bend. Each 2043.00
1.22.2 PVC with PVC bend as per IS : 7231 Each 1389.00
1.22.3 PVC with PVC bend of make Commander champion Each 1300.00
1.22.4 WVC for symphonic EWC. Each 2642.00
1.22.5 PVC with CP brass long band. Each 1643.00
1.23 P & F Automatic Flushing Cistern of first quality (IS : 774 mark) of
approved make fitting, siphon with copper tube, C.I. brackets complete
including cutting and making good the wall. WVC (as per IS : 2556) 10
litres
Each 1223.00
Note :- Deduct if plastic syphon is used.
1.24 P & F Flush Pipe of approved make with complete fittings for high level
flushing cistern:
1.24.1 G.I. `B` class (Concealed) 25mm. Each 487.00
1.24.2 G.I. `B` class (Concealed) 32 mm. Each 609.00
1.24.3 PVC exposed (heavy) 32mm. Each 182.00
1.24.4 GI (Sheet) hot galvanized exposed (10 litres). Each 270.00
1.25 P & F WVC (10 litres) low-level flushing cistern with cover. Each 1064.00
1.26 P & F WVC (10 litres) low-level flushing cistern cover only Each 427.00
1.27 P & F WVC syphon with plunger plate only. Each 297.00
1.28 P & F WVC Auto cistern with cover only. Each 722.00
1.29 P & F WVC Auto cistern cover only. Each 229.00
1.3 P & F C.P. brass Urinal Flush Pipe set complete with flanged brackets
of approved make.
1.30.1 For 4 Urinals Each 1653.00
1.30.2 For 3 Urinals Each 1043.00
1.30.3 For 2 Urinals Each 769.00
1.30.4 For 1 Urinal Each 543.00
1.31 P & F C.P. brass Urinal Spreader for stall urinal of approved make.
S-1 Page 31
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.31.1 P & F Synthetic (PTMT) Urinal Spreader for stall urinal of approved
Each 458.00
make.
1.32 P & F C.P. brass Doom Waste Coupling 32 mm dia. Each 318.00
1.32.1 P & F C.P. brass Doom Waste Coupling 40 mm dia. Each 332.00
1.33 P & F Plastic Syphon of approved make for automatic flush tank.
Each 231.00
1.34 P & F Copper tube Syphon for auto flush tank.
Each 420.00
1.35 Removing and re-fixing of wash hand basin including allnecessary
fittings.
Each 165.00
1.36 P & F C.I. brackets duly painted including cutting & making good the
wall.
Pair 135.00
1.37 P & F C.P. Brass flush Valve with C.P. flush bend of approved make.
1.41.2 Fire clay glazed kitchen sink (I.S. Marked) size 600 x 450 x 200 mm.
Each 3161.00
S-1 Page 32
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.41.3 WVC Lab sink (IS:2556 mark) size 530 x 430 x 180 mm Each 2770.00
1.41.4 WVC Lab sink (IS:2556 mark) size 500 x 350 x 150 mm Each 1900.00
1.41.5 WVC Lab sink (IS:2556 mark) size 450 x 300 x 150 mm Each 1768.00
1.41.6 Mosaic fine polished kitchen sink size 600 x 450 x 200mm. Each 1072.00
1.41.7 Mosaic fine polished kitchen sink size 450 x 450 x 200mm. Each 896.00
1.41.8 Mosaic fine polished kitchen sink size 600 x 450 x 200 mm with 600 x
Each 1172.00
450mm drain board
1.41.9 1.0 mm thick Salem stainless steel AISI -304 kitchen sink of approved
make (Nirali, Neel – kanth, Jaina, Faber-Castell ) with large waste
coupling.
Overall size Bowl size
(inches) (inches)
1.41.10 18 x 16 x 6 16x14x6 Each 3430.00
1.41.11 22 x 18 x 7 20x16x7 Each 4172.00
1.41.12 24 x 18 x 8 20x16x8 Each 4294.00
1.41.13 37 x 18 x 7 17x15x7 (with drain board) Each 5600.00
1.41.14 45 x 20 x 8 20x16x8 (with drain board) Each 9787.00
Note :- Deduct for item No 1.41.9 to 1.41.14 for using any other make
than specified above.
1.42 P & F Drain Board of approved make with C.I. brackets duly painted
compolete including cutting & making good the wall:
1.42.1 WVC (I.S.: 2556 Mark) size 530 x 450mm Each 1260.00
1.42.2 Mosaic fine polished size 600 x 450 Each 270.00
1.43 P & F 1st quality WVC pedestal for wash basin. Each 832.00
MISCELLANEOUS
1.44 P & F Bottle Trap of approved make :
1.44.1 C.P Brass 32 mm Each 562.00
1.44.2 C.P Brass 40 mm Each 668.00
1.44.3 Synthetic Material (PTMT)32 mm Each 470.00
1.44.4 Synthetic Material (PTMT)42 mm Each 495.00
1.44.5 P.V.C Each 85.00
1.45 P& F waste Coulping with fittings of approved quality /make:
1.45.1 C.P Brass 32 mm dia Each 139.00
1.45.2 C.P Brass 40 mm dia Each 211.00
1.45.3 Synthetic Material(PTMT) 32 mm Each 95.00
1.45.4 Synthetic Material (PTMT)40 mm Each 139.00
S-1 Page 33
CHAPTER S-1
Chapter Description Unit Rate
Code No.
S-1 Page 34
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.59.1 C.P. brass of Heavy & Superior quality 50x15mm Each 145.00
1.59.2 (-do-) 100 X 15mm. Each 167.00
1.59.3 (-do-) 150 X 15mm. Each 183.00
1.6 P & F Acrylic Toilet accessories set consisting of Towel rail, shelf, towel
ring, soap dish, paste & brush holder & twin peg of approved
quality/make.
Each 924.00
1.61 Labour Charges for removing WVC pan:
1.61.1 Indian/Orissa pan Each 99.00
1.61.2 European W.C. Each 99.00
1.61.3 Flushing cistern Each 46.00
1.62 P & F Jet spray for water closet with C.P. Copper Tube flange of
Each 290.00
approved make.
1.63 Providing & fixing C.P.flange for 15mm dia taps. Each 14.00
S-1 Page 35
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.64 Providing and fixing 1st quality standard white, grey, ivory, fume red
brown, light green, light blue and other light shades glazed tiles
confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls,
floors, steps, pillars etc. laid on a bed of nea
P.Sqm 693.00
1.64.3 Add extra over item no. 1.64.1 and 1.64.2 for Marble printed, granite
0.15
shade tiles.
1.64.4 Add extra over 1.64.1 and 1.64.2 for using coloured dark shade tiles
instead of White / Ivory / Light Grey/ Light Green/ Sky Blue/ Light
Brown and other light shade coloures.
P.Sqm 85.00
1.65 Providing and fixing 75 mm wide Decorative Border in different shades
and in all coloures for glazed tiles
P.Rmt. 300.00
1.66 Providing and fixing Motive pieces all coloures for glazed tiles.
1.66.1 Size 200 x 200mm Each 132.00
1.66.2 Size 200 x 300mm Each 164.00
1.67 Providing and fixing 1st quality MAT finished ceremic tile size
300x300mm confirming to IS : 13755 and IS : 15622 colour such as
white, grey, ivory, fume red brown, light green, light blue and other light
shades in floors, steps, pillars etc. laid on a b
P.Sqm 790.00
1.67.3 Add extra over item No 1.67.1 and 1.67.2 for using 400x400mm size
P.Sqm 84.00
MAT finished tiles in place of 300x300mm size
1.67.4 Add extra over 1.67.1 and 1.67.2 for using coloured dark shade tiles
instead of White / Ivory / Light Grey/ Light Green/ Sky Blue/ Light P.Sqm 84.00
Brown and other light shade coloures.
1.68 Extra for using Marble printed / Granite shade or dark shade
tiles instead of white, grey, ivory, fume red brown, light green,
light blue and other light shades in glazed tiles and MAT finished Sqm 0.10
tiles.
1.69 Extra for using size above 200x300mm in glazed tiles and for using
400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. Sqm 0.10
1.7 Filling of sunk portion of roof with earthen pots of required height
including filling voids with 1:3:6 light concrete, using brick bats
complete levelling and dressing the surface by 50mm thick cement Cum 1538.00
concrete 1:2:4 as per specification.
S-1 Page 36
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.71 P & F C.P. Health Faucet with 1Mtr. Long Tube & Hook of approved
Each 653.00
make and heavy as per direction of Enginner-in-Charge
1.72 P & F C.P. brass Urinal Spreader for Large Urinal of heavy duty of
Each 642.00
approved make as per direction of Enginner-in-Charge
1.73 Removing & Re fixing of P.V.C. Cistern fittings (Syphon, Ball cock &
Each 414.00
Handle Set) complete as per direction of Enginner-in-Charge
1.74 Providing & Fixing Premium Quality white glazed vitreous china
Sanitary Wares (IS:2556 Mark) of approved make as per direction of
Engineer-in-charge including cutting and making good the wall and
floor.
1.74.1 W.C. orissa pan with 100 mm vitreous china P or S trap Each 2786.00
1.74.2 Universal (anglo-Indian type) with P or S trap Each 5805.00
1.74.3 Wall Mounting European type W.C. Each 8247.00
1.74.4 Double Syphonic European W.C. with mounted W.V.C. flushing cistern
of 10 litre capacity complete with all necessary internal fittings with Each 16217.00
Hydraulic seat cover.
1.75 Providing & Fixing premium qulaity WVC Urinal with PVC waste pipe,
dome couplings, concealed iron brackets or screws etc. complete.
1.76 Providing & Fixing premium qulaity W.V.C. Urinal Partition plate of size
Each 2396.00
630x315 mm
1.77 Providing & Fixing premium qulaity WVC Wash basin with C.I. brackets
duly painted & 32 mm C.P. brass waste coupling of approved make
with PVC waste pipe complete
1.77.1 Size 550 mm x 400 mm Each 2122.00
1.77.2 Size 550 mm x 400 mm dia for counter top. Each 3065.00
1.78 P & F Premiumquality water closet Seat Covers with brass hinges
Each 649.00
complete Solid PVC (ISI marked) grade-I White for EWC.
1.79 P & F Premium quality Low level Flushing Cistern of 10 litres capacity
(IS:2556 mark) of approved make as per Engineer-in-charge with
complete fittings C.I. brackets duly painted, brass ball cock with ball, Each 1657.00
(IS:1703 mark) complete including cutting and ma
1.8 P&F Looking Mirror 5mm thick of approved make with ornamental
frame size 50x12 with 6mm Ply Board on Back Side Complete as per Sqm 2313.00
approved sample
1.82 Providing & Fixing chair for wall hung W.C. Each 1458.00
S-1 Page 37
CHAPTER S-1
Chapter Description Unit Rate
Code No.
1.83 Providing & Fixing Concealed cistern with Floor mounting frame and
flush plate of superior quality and approved sample by Engineer-in- Each 7560.00
charge.
1.84 Providing and fixing new spindle for Bib cock/pillar cock for repairing
Each 104.00
purpose to solve leakage and proper functioning of tap.
1.85 Providing & Fixing premium quality Toilet corner Glass Shelf size
225x225mm with C.P. brass brackets & guard rail edges rounded of SS Each 1420.00
frame
1.86 Providing & Fixing premium quality waste coupling 32mm half
Each 472.00
thread as per approved by Engineer in Charge.
1.87 Providing & Fixing Premium quality Bottle trap internal portion 32mm,
size 250mm long wall connection pipe & wall flange as per approved Each 1454.00
by Engineer in Charge.
245242.35
S-1 Page 38
CHAPTER : B-17
ADDITIONAL MISCELLANEOUS ITEMS
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
Sqm 626.00
17.1.1 Add extra for 0.60mm TCT (Total Coated Thickness) high tensile Zinc
aluminum alloy coated galvaiumeseel sheet in place of 0.50mm thick
17.1.2 Add extra for 0.80mm TCT (Total Coated Thickness) high tensile Zinc
aluminum alloy coated galvaiumeseel sheet in place of 0.50mm thick
ChapB-17 Page 39
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
Walls: Insulated sandwich panels for wall of total thickness mentioned
below. Panel shall have 0.50mm (+/-0.04mm) thick pre coated metal
sheet on both sides of rigid PUR insulation. The pre-coated metal sheet
shall be PPGL (Pre Painted Galvalume Sheet wit
ChapB-17 Page 40
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.5 Supply and Installation of WALL – PREFABRICATED INSULATED
LAMINATED FACE PANEL:
Factory-readymade interior wall panel of thickness mentioned below.
The panels shall have suitable provision for joining adjacent panels.
Interior panels may have optional pro
17.6 Supply and Installation of SMALL ROOM (TOILET & GUARD ROOM) –
PREFABRICATED INSULATED PPGL FACE PANEL:
Insulated closed lip panels (for door, wall and roof) of thickness
mentioned below. Panel shall have 0.50mm (+/-0.04mm) thick pre-
coated metal sheet on both sides of rigid PUR insulation. The pre-
coated metal sheet shall be PPGL (Pre Painted Galvalume She
ChapB-17 Page 41
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
50mm x 50mm RMT 150.00
100mm x 100mm
17.8 Supply and fixing of Cement Bonded Particle Board (as per IS 14276)
false ceiling using 6MM thick Cement Board with galvanized and pre
painted steel T section of size 24mm x 27mm x 0.4mm for main T
duty pre punched to accept cross T section of
Sqm 594.00
ChapB-17 Page 42
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.9 Supply and fixing of Cement Bonded Particle Board (as per 14276) wall
paneling using 10 MM thick Cement Board with frame work made of GI
stud section of size 48mm x 35mm x 0.55mm thick placed at every 610
mm C/C intervals vertically and at 1200mm internal
Sqm 1526.00
17.1 Supply and fixing of Cement Bonded Particle Board (as per 14276)
double skin partition using with 10 MM thick Cement Board made out
of G.I. track section of size 50mmx 35mm x 0.55 mm for fixing to the
roof and floor and stud section of size 48m
Sqm 2208.00
17.11 Supply and fixing of Factory Laminated Cement Bonded Particle Board
double skin partition using with 10MM Factory Laminated Cement
Bonded Board made out of G.I track section of size 50 mm x 35mm x
0.55mm for fixing to the roof and floor and stud section o
Sqm 3092.00
17.12 Supply and fixing of Bath room / Toilet door shutter with 16mm Factory
Laminated Cement Bonded Particle Board BISON Lam (IS 14276)
door shutter with all-round ‘U’ lipping of PPS section of size 12mm X
18mmX 12mmX0.6mm thickness with a hardware of 12mm di
Sqm 2188.00
ChapB-17 Page 43
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.13 Solid Rectangular Block (400x200x200, 400x200x100, 400x200x150,
225x200x100)
Cum 9370.00
Cum 6675.00
Cum 9920.00
ChapB-17 Page 44
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.16 Interlocking Paver Blocks having 80 mm thickness in M-40 grade
concrete
Providing and Laying 80 mm thick cement concrete blocks of M-40
Grade (Manufactured with fully mechanised dry cast process with
forced action mixer whose arms revolve along the main axis and rotate
about its own axis also, having humidity sensor for moist
Sqm. 1100.00
Sqm. 1289.00
Sqm 1424.00
ChapB-17 Page 45
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.19 Interlocking Paver Blocks having 100 mm thickness in M-55 grade
concrete
Providing and Laying 100 mm thick cement concrete blocks of M-55
Grade (Manufactured with fully mechanised dry cast process with
forced action mixer whose arms revolve along the main axis and rotate
about its own axis also, having humidity sensor for mois
Sqm 1389.00
Sqm. 1489.00
Cum 8572.00
ChapB-17 Page 46
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.22 Kerb Stones of 1200x300x150, 1000x400x150, 1000x600x150,
600x300x150 size (M-40)
Providing and Laying cement concrete Kerb Stones of different sizes in
M-40 grade (Manufactured with fully mechanised dry cast process with
forced action mixer whose arms revolve along the main axis and rotate
about its own axis also, having humidity sens
Cum 9067.00
17.23 Cellular Concrete Block for Pitching and garden paths (600x400x80) in
M-30
Providing and fixing Cellular concrete blocks (M-30 Grade),
600x400x80 mm sizes (Manufactured with fully mechanised dry cast
process with forced action mixer whose arms revolve along the main
axis and rotate about its own axis also, having humidity sensor
Sqm. 739.00
Sqm. 894.00
ChapB-17 Page 47
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.25 Pre Cast U/Semi circular Drains (Outer size 600x400 mm, wall
thickness 80 mm)
Providing and fixing Precast concreteUdrains (M-30 Grade) of different
sizes (Manufactured with fully mechanised dry cast process with forced
action mixer whose arms revolve along the main axis and rotate about
its own axis also, having humidity sensor fo
R.M. 417.00
17.26 Dry Cleaning of sofa sets using shampooing machine with all materials
& drying it do the level using machinery at designated place by
engineer-in-charge one seat of sofa (payment for multi seater sofa will
be done as the number of seats of that sofa.)
17.26.1 Single Seater Sofa Each 140.00
17.26.2 Two Seater Sofa Each 211.00
17.26.3 Three Seater Sofa Each 302.00
17.27 Dry Cleaning of Woolen Carpet of any size using shampooing machine
with all material & drying it using machinery at the designated place as Sqm 93.00
told by engineer in charge.
17.28 Complete replacement of Tapestry cloth of Sofa set costing @ Rs. 300/-
per Mtr. Approx of superior quality including stitching charges (As
approved by the Engineer in Charge) as per existing pattern/design.
17.29 Complete replacement of damaged foam of Sofa set and using 100mm
thick Joint less P.U. foam in seat of 32 density feather foam of superior
quality of approved make (as approved by the Engineer-in-charge)
pasted with Adhesive (Rubber Solution) of superio
17.3 Complete replacement of damaged foam of Sofa set and using 50mm
thick joint less P.U. foam of 32 density feather foam superior quality of
approved make (as approved by the Engineer-in-charge) in back duly
pasted with Adhesive (Rubber Solution) of superior
ChapB-17 Page 48
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.31 Complete replacement of damaged foam of Sofa set and using 25mm
thick joint less P.U. foam of 32 density feather foam superior quality of
approved make (as approved by the Engineer-in-charge) in Hand rest,
in seat and back and design work as required of
17.32 Repair of wooden frame of Sofa set using Tat, Nail, Screw, Bolt (if
required) and re-assembling sofa set (Cost Including all Consumble
Item) complete in all respect as per direction of the Engineer-in-charge
17.33 Repair using replacement of Jata, Dori, wooden batten & legs
everything in all respect as per approval of Engineer-in-charge.
17.33.1 Single seater sofa Each 456.00
17.33.2 Three seater sofa Each 686.00
17.34 Providing and Fixing machine made Synthetic Carpet having total
Carpet weight 850 gm Psqm. and 5mm thickness superior quality Each 440.00
complete in all respect as per direction of Engineer-in-charge.
17.35 Providing and Fixing Chiken wire mesh at the joint of masonry
Sqm 71.00
members/ R.C.C. Members with Nails complete in all respect.
17.36 Covered & water proof Dome type mehfil pandal with iron frame, white
wall curtains with ply and false ceiling etc. complete in all respects with
provisions of few gates and pressboxes inside the pandal as per Sqm 260.00
requirement. Approx height 20-25 feet with new
17.37 Preparing VIP Room 15'×30' Water Proof Ceiling white Curtain on wall
(New). Carpet flooring. With Sofas, Center Tables etc with Chemical
Toilet complete having Europen W.C., Wash Basin,PVC water tank, No 60000.00
Water Connection, Towel rail, soap dish etc complete i
17.37.1 Chemical Toilet complete having Europen E.C., Wash Basin,PVC water
tank, Water Connection, Towel rail, soap dish etc complete in all No 15000.00
respect.
17.38 Box Gate (New) 16'×14' No 7500.00
17.39 P/F side wall (New Cloths) Sqm 40.00
17.4 P/F Barricading in Stadium Area Two Horizantel line with Ballies Vertical
Sqm 131.00
Ballies 2.5 Mtr. c/c Complet with clothing etc. (New)
17.41 Hire charges for Chair Banquet No 75.00
17.42 Hire charges for flower decoration original & Duplicate stage, entry gate
No 26132.00
etc. complete as directed by engineer in charge
17.43 Hire charges for Jhalar (New) Rmt 27.00
17.44 Hire charges for Non woven synthtic carpet (Red/Green) (New) Sqm 27.00
17.45 Hire charges for Wooden stage height 120 to 150cm, with steps made
of 50mm dia iron pipe frame with adjustable height system and having Sqm 187.00
smooth top wooden board complete.
17.46 Hire charges for V.V.I.P. sofa set good quality No 2115.00
17.47 Hire charges for folded type two seater sofa set (cum bed) with good
Each 254.00
quality white cloth cover
ChapB-17 Page 49
CHAPTER : B-17
Chapter Description Unit Rate
Code No.
17.48 Hire charges for White cotton cloth cover for padded chair including
Each 12.00
ribbon
17.49 Hire charges for PVC Chair Each 7.00
17.5 Hire charges for Wooden Table 6'×3' (Babool) Each 30.00
17.51 Hire charges for White cotton chader (Sheet) (Washed) Each 15.00
17.52 Hire charges for Centre Table sunmica Top 2'×4' Each 22.00
17.53 Hire charges for Pipe Pandal ht upto 12 to 18 ft Sqm 30.00
17.54 Drinking water arrangement :
17.54.1 Drinking water bottle 200 ML Bislery/Aquafina No 12.00
17.54.2 Drinking water bottle 1 Ltr Bislery/Aquafina No 19.00
17.55 Buke + Guldaste No 249.00
17.56 Hire charges for Providing fire extinguishers No 622.00
17.57 Providing & fixing flax work including Lettering, printing etc. complete
ChapB-17 Page 50
CHAPTER : B-16
ALLUMINIUM & PVC WORK
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.1 Providing and fixing anodized aluminum work (Anodizing to be got done
from approved Anodizer) for doors ,windows, ventilators and partition
with extruded built up standard tubular and other sections of approved
make conforming to IS :733 and IS :1285 anod
16.1.3 For shutters of sliding windows and making provision for fixing of fittings
Kg 425.00
wherever required (lockes shall be paid for separately).
Note : Add 10% extra over item No. 16.1 for work done in curved / circular
shape.
16.3.1 With glass panes of 4.0 mm thickness ( weight not less than 10.0
Sqm 996.00
kg/sqm) as per IS : 2835.
16.3.2 With glass panes of 5.0 mm thickness (weight not less than
Sqm 925.00
13.75kg/sqm) as per IS : 2835.
ChapB-16 Page 51
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.3.3 With tinted glass panes of 5.0mm thickness (weight not less than
Sqm. 1126.00
13.75kg/sqm).
16.4 Providing & fixing double action hydraulic floor spring of approved
brand and manufacture to aluminum door shutter including cost of
cutting floors as required, embedding in floors and cover plate etc.
complete as per direction of Engineer In-charge.
16.4.2 Approved brand like Hardwin Euro Superior quality or equivalent for
Each 2657.00
extra heavy doors.
16.5 Providing and fixing expanded grill made of anodized aluminum as per
design and drawing having members section of size 7.5mm x 6.0mm
and opening of size 102mm x 99mm to aluminum window/vent with
required screws, Y and H aluminium sec (as per drawing) at t Sqm. 2657.00
16.5.1 S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the
aluminium window by Aluminium beading 20x3mm with suitable screws
at not exceeding 150mm distance at all heights with all lead and lift with Sqm 800.00
scafolding.
16.6 Providing and fixing brass lock without handle for Aluminium door, of
approved quality, make & design as directed by Engineer In-charge. Each 452.00
16.7 Providing and fixing friction stay for aluminum windows, Ebco or Each
459.00
equivalent , complete in all respect size 10”. Pair
16.8 Providing and fixing sun control film, 25 micron thick of approved colour
and shade , complete in all respect , at all level , as directed by Sqm 434.00
engineer- in -charge.
16.9 Providing and fixing powder coated aluminium 1.5" dia drapery rod with
finials , rings end cap cording set and bracket etc. complete of
approved make (Arolux, Mac, vista or eqvi.) and approved design as
per specification and direction of engineer- in–cha
(a) For first 0.90 meter length of rod . Rmt 935.00
(b) For subsequent length of rod ( beyond 0.90 m length covered in item
Rmt 645.00
1(a) above).
c) Deduct if cording set not used from Item 6.9 (a). Rmt 150.00
16.1 Providing and fixing vertical blinds , made out of non woven polyester
fabric 85 to 90 mm wide of approved shade & design with power coated
aluminum channel minimum 1”x1” system including cording set etc. Sqm 2415.00
complete as per specification & direction of engi
ChapB-16 Page 52
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
(b) Section 63.00 x 38.00mm Rmt. 81.00
16.13 Polyester powder coating and electro coloring in various color and
shade approved by Engineer In charge. (For item No. 16.1.2 & 16.1.3) Sqm 504.00
16.16 Providing and fixing of Plastic shutter Infill made from extruded multi
chamber hollow P.V.C. section having cross section of 200 x 20 x 1mm
and shutter frame made from extrude P.V.C. section in the configuration
of double walled ‘C’ section having an ove Sqm. 2677.00
16.17 Providing and fixing of Plastic shutter Infill made from multi chamber
hollow P.V.C. sections having cross section of 200 x 20 x 1mm and
shutter frame made from Aluminum ‘C’ section size 23.6 x 20 x 1.8mm
and door fitting such as hinges, aldrop, handles,
16.18 Providing and fixing of Plastic shutter Infill made from hollow Plastic
sections in the dimension of 150 x 12 x 1mm and shutter configuration
of an ‘A’ section having an overall cross section of 47 x 26mm and door Sqm 1932.00
fittings such as hinges, aldrop, handles,
16.19 P & F of All PVC Door shall be made from extruded PVC sections
reinforce with steel. The corners & joints shall be miter cut and
welded/Mechanical joint. The outer frame and shutter frame shall be
made from PVC section having an cross section of 53 x 60mm
16.19.1 SHUTTER Panel infill made from PVC section 200 x 20 x 1 mm. Sqm 4448.00
16.19.2 SHUTTER Panel fully Glazed with 5mm thick plain glass Sqm 4217.00
16.19.3 SHUTTER Panel Partly Glazed with 5mm thick plain glass and partly
Sqm 4368.00
paneled with PVC sections 200 x 20 x 1mm.
ChapB-16 Page 53
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.2 Providing and fixing to existing door frame 24mm thick factory made
PVC door shutter made of styles and rails of a UPVC hollow section of
size 59x24mm and wall thickness 2mm ± 0.2mm with inbuilt edging on
both sides. The styles and rails mitred and jointe
16.23 Providing and fixing of All Plastic fixed Windows made from PVC
section reinforced with steel. The Corners & joints shall be miter cut and
welded. The outer frame shall be made from extruded PVC sections
having on overall cross section of 53 x 60mm suitab
Sqm 2355.00
ChapB-16 Page 54
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.24 Providing and fixing of All Plastic Two track sliding Windows shall be
made from extruded PVC sections reinforced with Steel. The corners &
joints shall be miter cut and welded. The outer frame shall be made
from extruded PVC section having an overall cr
Sqm 3663.00
16.25 Providing and fixing of All plastic fixed louvered Ventilators shall be
made from extruded PVC section reinforce with steel. The corners and
joints shall be miter cut and welded. The outer frame shall be made
from extruded PVC section having an overall cr Sqm 2777.00
16.26.1 Providing and fixing of All Plastic Fly Mesh shutters shall be made from
extruded PVC section having an overall cross section of 30 x 23mm
E.P.D.M. weather scales shall be provided to make it air tight. Mosquito Sqm 1691.00
net of nylon/ polymer/GI mesh to be fixed o
16.26.2 P&f FRP door shutter made from special fibreglass reinforced plastic
sheet and polyurethane foam core, FRP Sheet should be made from
emulsion bonded CMS having single fibre tensile strength of
3.6x103N/mm² and co-efficient of thermal conductivity 1.04 W/M
Sqm 3600.00
PLASTIC
PARTITIO
N
16.27 Providing and fixing of all Plastic partition with frames made from
extruded PVC sections having on overall cross section of 53 x 60mm.
The frames shall be joined by means of concealed cleats. Suitable snap
Fit glazing beads and function beads having an o
16.27.1 Partition made from PVC section 200 x 20 x 1mm Sqm 3613.00
16.27.2 Partition infill fully glazed with 5mm thick plain glass. Sqm 3269.00
16.27.3 Partition infill partly glazed with 5mm thick plain glass and partly
Sqm 3502.00
paneled by PVC section 200 x 20 x 1mm.
ChapB-16 Page 55
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.28 Providing and fixing of suspended false ceiling in the grid of 600 x 600
mm/600 x 600 to 900 x 900mm using aluminum tees with inter lock
system of main tee, cross tee and wall angle (size of tee and angle
approx. 25mm x 25mm x 0.5mm or equivalent) etc. co
P.V.C. PELMETS :
16.29 Providing and fixing PVC pelmets made out from multi chamber hollow
Plastic section with tongue & grooves size 12 x 150mm, Iron brackets, Mtr. 291.00
20mm dia C.P. Steel Curtain rod complete.
16.3 Providing and fixing paneled portion with Mild Steel Section ,having size
of 25x38 mm with a wall thickness of 1.2 mm ± 0.1 mm the members
are jointed by M.S Cleat of 75 x75 x2 mm size having usual process
variation and with the necessary screws as per r
Sqm 2050.00
16.31 Providing and fixing of false ceiling at a height decided by the engineer
in-charge on a M.S made skeleton frame work .The perimeter square
M.S. Pipe shall be fixed along with the wall ,having dimension of 25x25
mm and with a wall thickness of 1mm +/- 0.3
After the grid work is completed ,it has to be covered by the multi-
chamber hollow PVC section from below , with the help of self –
tapping screw of 19 mm x 8mm. These PVC hollow section are having
an overall dimension of 150 mm x 10 mm or 254 mm x 6 mm
Sqm. 1510.00
ChapB-16 Page 56
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.32 Providing and fixing of wall paneling on the frame work made out of G.I
channel of size 75x10 mm or from wooden ripper of required size with
CSK wood screws of size 50x8 mm fixed to the wall with rowel plug at
a spacing of 900 mm center to center . The
Sqm. 1257.00
16.33 Providing and fixing factory made polyvinyl chloride (PVC) Door frame
of the size 50x47mm with a wall thickness of 5mm made out of
extruded 5mm, made out of extruded 5mm PVC foam sheet, mitre cut
at two corners and jointing with 2 nos. of 150mm long brack
Rmt 475.00
16.34 Providing and 30mm thick factory made Solid Panel PVC Door Shutter
consisting of frame made out of M.S. tubes of 19 gauge thickness and
sizes of 19mm for styles & 15mm x 15mm for top and bottom rails. M.S.
frame shall have a coat of steel primers of appro
ChapB-16 Page 57
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
including all door fittings such as Hinges, L-drop, Handles, Locking
Sqm. 3180.00
bolts etc. as per approved of Engineer-in-charge
16.35 Providing and fixing 30mm thick FACTORY MADE SOLID BOTH SIDE
PRELAM PANEL PVC DOOR SHUTTER consiting of frame made out
of M..S. tubes of 19 gauge thickness and size of 19mm x 19mm for
stiles top & bottom rails M.S. farme shall have a coat of sheet primers
as gap insert for top rail and bottom rail. Panelling of 5mm thick both
side Prelam PVC sheet to be fitted in the M.S. frame welded / sealed to
stile and rails with 7mm (5mm + 2mm) thick x 15mm wide PVC sheet
beading on inner side and jointed together wi
Sqm. 4138.00
16.36 Providing and fixing Prelaminated PVC sheet wall panelling of thickness
5mm stuck on inner frame work of 50mm vide strips of 5mm thick PVC
sheet. The strip should have in their center a groove of 6mm width and
1mm depth for sinking the head of the screw u
ChapB-16 Page 58
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.37 Providing and fixing Structural glazing work with toughened glass of
6mm thick and reflective colour as approved in dark shade like
Blue/Dark Blue etc. with frame work of curtain section 65x60mm
(Weight 1.64 kg/m min.) made of aluminium with chrome platin
Sqm 5008.00
16.38 Supply and fixing of polycrete wall fencing of existing wall, fencing of
0.9 mtr. Height above the existing wall, main member PVC profile
section of size 125mmx125mmx900mm (c/c 1.67 mtr. length) with a
wall thickness of 2.00mm+0.20mm and Horizontal panel
Sqm 2407.00
Sqm 4912.00
16.4 Providing and fixing expanded grill made of aluminum as per design
and drawing having members section of size 7.5mm x 6.0mm and
opening of size 75mmx72mm to aluminum window/vent with required
screws, Y and H aluminium sec (as per drawing) at the ends and
ChapB-16 Page 59
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.40.2 Powder coating aluminum ( minimum thickness of powder coating 50
Sqm 1753.00
micron)
16.41 Providing and fixing expanded grill made of aluminum as per design
and drawing having members section of size 7.5mm x 6.0mm and
opening of size 50mmx48mm to aluminum window/vent with required
screws, Y and H aluminium sec (as per drawing) at the ends and
16.42 Providing and fixing of uPVC Sliding windows: Frame Made from the
Extruded uPVC Window Profile Section of size 106w x 50h mm having
outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber
construction, White in finish, duly reinforced with 1.2 m
Sqm 8013.00
16.43 Providing and fixing of uPVC Sliding windows: Frame Made from the
Extruded uPVC Window Profile Section of size 106w x 50h mm having
outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber
construction, Laminated (colour) finish, duly reinforced
Sqm 12503.00
ChapB-16 Page 60
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.44 Providing and fixing of uPVC Sliding windows: Frame Made from the
Extruded uPVC Window Profile Section of size 106w x 50h mm having
outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber
construction, White in finish, duly reinforced with 1.2 m
Sqm 5957.00
16.45 Providing and fixing of uPVC Sliding windows: Frame Made from the
Extruded uPVC Window Profile Section of size 106w x 50h mm having
outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber
construction, Laminated (colour) finish, duly reinforced
Sqm 10187.00
Sqm 9576.00
ChapB-16 Page 61
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.47 Providing and fixing of UPVC casement fully openable windows
(outward / inward): Outer Frame made from the Extruded UPVC
Windows profile section of size 60w X 60h mm having outer wall
thickness of 2.5mm (+/- 0.2mm) and three chamber constuction in
Laminat
Sqm 13474.00
Sqm 11027.00
Sqm 14272.00
ChapB-16 Page 62
CHAPTER : B-16
Chapter Description Unit Rate
Code No.
16.5 Providing and fixing of openable uPVC Doors with or without fix top:
Frame Made of Extruded uPVC Window Profile Section of size 60w x
70h mm having outer wall thickness of 2.75mm (+/- 0.2mm) and 3 box
multi-chamber construction, White in finish, duly rein
Sqm 9930.00
16.51 Providing and fixing of openable uPVC Doors with or without fix top:
Frame Made of Extruded uPVC Window Profile Section of size 60w x
70h mm having outer wall thickness of 2.75mm (+/- 0.2mm) and 3 box
multi-chamber construction, Laminated (colour) finish,
Sqm 13558.00
ChapB-16 Page 63
CHAPTER : B-15
MISCELLANCEOUS BUILDING ITEMS AND WATER PROOFING TREATMENT
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.1 Providing and laying damp-proof course 25mm thick with cement
sand mortar 1 : 3 including two coats of hot blown bitumen (2 Kg. per Sqm. 120.00
Sqm) complete as per specification.
15.2 Providing and laying damp-proof course with cement concrete grade
M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof
compound including two coats of hot blown bitumen (2Kg. per Sqm)
complete as per specification with glass strip 3mm thick a
15.3 Providing and laying horizontal damp proof course with Hessian base
self-finished bitumen felt, type 3 grade 2 including hot applied Blown
bitumen coating, 10cm. thick cement concrete fillet complete as per Sqm. 345.00
specifications
15.4 Providing and laying horizontal fiber base self-finished felt type 2
grade 3 including hot applied blown bitumen coating. 10cm. thick Sqm. 360.00
cement concrete fillet complete as per specification.
15.5 Providing and laying premixed tar or bitumen damp-proof
Sqm. 58.00
course 40mm thick (excluding cost of bitumen).
15.6 Providing & fixing precast cement concrete coping 1 : 2 : 4
mix 50mm thick complete as per specification :
50mm Thick Sqm. 222.00
15.7 Deduct in item No. 15.2 if no glass strips are used. Sqm. 21.00
15.8 Deduct in item No. 15.2 for not applying 2 coats of hot
Sqm. 30.00
blown bitumen complete as per specifications.
EXPANSION JOINT :
15.9 Expansion joint raised type including cutting & finishing joint, raising
brick pardi including plaster and making gola around pardi covered
with kota stone with required slop to repel water effectively. Mtr. 272.00
ChapB-15 Page 64
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.10.2 Bitumen felt (glass fiber base) type 2 grade-I. Sqm. 252.00
15.11 Providing and laying six courses water proofing treatment with
bitumen felt over roofs consisting of first, third and fifth courses of
blown bitumen or / and residual bitumen applied hot @ 1.45 ,1.20
and 1.45 Kg per sqm. of area respectively second and f
Sqm. 373.00
15.12 Providing and laying six courses water proofing treatment with
bitumen felt over roofs consisting of first, third and fifth courses of
blown or/and residual bitumen applied hot at 1.45, 1.20 and 1.70 Kg.
per Sqm. of area respectively second and fourth cou
Sqm. 373.00
15.13 Providing and laying six courses water proofing treatment with
bitumen felt over roofs consisting of first, third and fifth courses of
blown or/and residual bitumen applied hot at 1.45, 1.20 and 1.70Kg.
per Sqm of area respectively second and fourth cours
Sqm. 367.00
15.15 Supplying and laying under layer of bitumen saturated felt type-1. Sqm. 76.00
ChapB-15 Page 65
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.17.1 Lime concrete with 20mm nominal size brick aggregate and 50% lime
Cum 1662.00
mortar 1 : 2 (1 lime putty : 2 surkhi).
15.18 Providing and laying two coats of black rubberized water proof
coating after cleaning the existing surface with wire brush, surface
should be free from dust, loose particle, oil and grease etc. Apply 1st
coat over surface or RCC/Stone slab/Lime terrace/an Sqm. 76.00
15.19 Add extra over item No. 15.18, if 3rd coat is applied for highly
Sqm. 29.00
affected surfaces.
15.2 Add extra over item No. 15.18, if white rubberized water proofing, is
Sqm. 44.00
used in place of black as per manufacturer specification.
15.21 Add extra over item No. 15.20, if 3rd coat of white rubberized water
Sqm. 29.00
proofer is applied for highly affected surfaces.
15.22 Providing and laying two coats of clear (colorless) water proofing
coating of Silicon water repellent over brick/ exposed stone masonry
facing/ Mosaic/ stone tile roofing/Interior and exterior walls surface
after cleaning with brush and apply with brush Sqm. 76.00
ChapB-15 Page 66
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.23 Providing and filling block rubberized joint filler in all visible cracks of
masonry/concrete/terrace concrete blocks/ canal lining
basement/A.C./G.I./sheets roofs gutters down pipes after removing
existing treatment and cleaning with wire brush and joint
Sqm. 100.00
15.24 Add extra over item No. 15.23, if white crack seal caulking compound
used in place of black above over terrace/RCC Crack in vertical walls
masonry/plaster/expansion joints door frame joints around wash
basin in fixed stone slab around bath tub glazed tile Sqm. 40.00
15.25 Providing and painting of Tank mastic anticorrosive paint two coats
on steel and concrete Tanks pipes fluid concrete etc. with surface Sqm. 7.00
duly clean and free from moisture.
15.29 Add extra for RC frames (Chowkhats) Curved in plan over item No.
Mtr. 10%
15.28.
15.3 Add extra over item No. 15.36 for finishing the exposed face with
Mtr. 20%
terrazo (Mosaic) finish.
ChapB-15 Page 67
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.35 Add extra over item Nos. 15.31, 15.33 & 15.34 for frames curved in
Mtr. 10%
plan
15.37 Providing and fixing on wall face CI rain water pipes including filling
the joint with spun yarn soaked in neat cement slurry and cement
mortar 1 : 2 (1 cement : 2 fine sand) :
ChapB-15 Page 68
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.4 Providing and fixing on walls face CI accessories for rain water pipes
including filling the joints with spun yarn soaked in neat cement slurry
and cement mortar 1 : 2 ( 1cement : 2 fine sand) :
15.40.1 CI plain bend :
(a) 75mm diameter. Each 216.00
ChapB-15 Page 69
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
ChapB-15 Page 70
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.41 Add extra over item No. 15.40 for providing lead caulked joint to sand
cast iron accessories for rain water pipes and fittings :
15.42 Providing, fixing and embedding sand cast iron accessories for rain
water pipes in the masonry surrounded with 12mm thick cement
mortar of the same mix as that of masonry (lead caulking will be paid
separately) :
15.43 Providing and fixing on wall face asbestos cement rain water pipe
including jointing with spun yarn soaked in bitumen and cement
mortar 1 : 2 (1 cement : 2 coarse sand) complete including
M.S. clamp :
ChapB-15 Page 71
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.44 Providing and fixing for A.C. pipe on wall plug and standard holder
bat clamps comprising of two semicircular valves of flat iron and cast
iron base screwed on wooden plugs is not done :
15.45 Providing and fixing on wall face asbestos cement fitting for rain
water pipes including jointing with spun yarn soaked in bitumen and
cement mortar 1 :2 (1 cement : 2 coarse sand) :
ChapB-15 Page 72
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.45.3 TEES
(a) 75mm dia without door. Each 38.00
15.45.4 SHOES
(a) 75mm dia. Each 24.00
ChapB-15 Page 73
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.45.5 SOCKETS
(a) 75mm dia. Each 15.00
15.46 Deduct in item No. 15.43 to 15.45, for using non ISI A.C.
20%
pipes / accessories.
15.47 Providing and laying integral cement based treatment for water
proofing on horizontal surface at all level as directed by Engineer- in-
Charge and consisting of :
(a) 1st layer of 20mm thick approved and specified rough stone slab
over a 25mm thick base of cement mortar 1:3 (1 cement: 3 coarse
sand) mixed with water proofing compound ‘Impermo’ of Snowcem or
equivalent conforming to IS:2645 in the recommended proportion
15.48 Providing and laying integral cement based treatment for water
proofing on the vertical surface by fixing specified stone slab 20mm
thick with cement slurry mixed with water proofing compound
‘Impermo’ of Snowcem or equivalent conforming to IS:2645 in rec
ChapB-15 Page 74
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
ChapB-15 Page 75
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
III) IIIrd course of applying blown or residual bitumen applied hot at 1.7
Kg per sqm. of area.
IV IVth course of 400 micron thick PVC sheet .(Overlaps at joints of
PVC sheet should be 100 mm wide and pasted to each other with Sqm. 265.00
bitumen @ Kg/sqm.)
15.5 Providing and fixing APP (Atactic Polypropylene Polymer) modified
Pre fabricated five layer 2mm thick water proofing membrance, black
finished reinforced with glass fiber matt manufactured by Bitumen
Company Ltd, Sopreme , Tamko,IWL India and Texsa India
ChapB-15 Page 76
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.53 Extra for covering top of membrane with Geotextile, 120gsm non
woven, 100% polyester of thickness 1 to 1.25mm bonded to the
membrane with intermittent touch by heating the membrane by Sqm.. 46.00
Butane Torch as per manufactures recommendation [ for Item
No.15.53 to
ChapB-15 Page 77
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.56 Providing & laying built up insulation & water proofing treatment at
all levels as per following specification and courses :
I Coarse
One coat of bituminous primer as per IS :3384 @ 0.3 liter per sqm.
II Coarse
One coat of straight run bitumen @ 1.5 kg/ sqm
III Coarse
First layer of 9mm thick expanded polyethylene sheets having
density 50 kg /m3 + 5% (R-Armours or equivalent) fixed with 100 mm
.wide neoprene adhesive.
IV Coarse
One layer neoprene adhesive @ 350 ml /sqm.
V Coarse
Second layer of 9mm .thick expended polyethylene sheets having
density 50 Kg/Cum. + 5% (R-Armour or equivalent ) fixed with
buttjoint and joint further sealed with 100 mm .wide stripe of
polymeric felt /EPE fixed with neoprene adhesive .
VI Coarse
63mm. thick P.C.C 1:3:6 ( 1cement :3 sand :6 stone aggregate ) in
panels of maximum 1.2m. 1.2 m size with 24 SWG 38mm . chicken
wire mesh interposed in between ,finished smooth and sealing joints
between the panels with eleastomeric mastic as per approv
15.57 Add extra over items of Cement Plaster / Cement Concrete flooring /
Plain or RCC work Providing and mixing admixture of synthetic Fiber
6mm / 12mm. Recron 3 S @ rate of 125gm. pack per 50 Kg. of P. Pack
Cement or in the ratio of as specified by manufacture specif 52.00
125gm.
ChapB-15 Page 78
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
15.58 Providing and laying a layer of acrylic polymer based single pack,
cold, brush applied liquid U.V. resistant waterproofing coating
Sunroof HB of Bitumen Co. Ltd. Tamko or Tremco in one coats over
entire prepared wall surface. A prime coat is coat is appl P. Sqm. 498.00
ChapB-15 Page 79
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
Sqm 1220.00
Sqm 828.52
15.61 Nano technology water proofing or anti stain protection coating 5-7
layer process for increasing life of all stone fascia/facades/flooring or
stone building and damage control protection, life 7-9 years, warranty
5 years-- before coating washing of stone
Sqm 937.00
Sqm 468.00
ChapB-15 Page 80
CHAPTER : B-15
Chapter Description Unit Rate
Code No.
Sqm 486.00
ChapB-15 Page 81
CHAPTER : B-14
DISMANTLING AND DEMOLISHING WORK
CHAPTER : B-14
Chapter Description Unit Rate
Code No.
14.1 Dismantling dressed stone work Ashlar face stone work, marble work
of precast concrete work including stacking of serviceable material
and disposal of unserviceable material within 50 meters leads.
14.11 Removing mortar from stones and cleaning stones and concrete
articles including stacking (net quantity of stacks of cleaned materials
will be measured) :
14.11.1 Lime mortar P.Cum 106.00
14.11.2 Cement mortar P.Cum 154.00
ChapB-14 Page 82
CHAPTER : B-14
Chapter Description Unit Rate
Code No.
14.12 Dismantling doors, windows and clearstory windows (steel or wood)
shutters including chowkhats, architrave and holdfasts etc. complete
and stacking within 50 meters lead :
14.12.1 Of area 3 square meter and below Each 82.00
14.12.2 Of area beyond 3 square meter Each 112.00
14.13 Taking out doors, windows and clearstory windows shutters (steel or
wood) including stacking within 50 meters lead :
14.13.1 Of area 3 square meter and below Each 32.00
14.13.2 Of area beyond 3 square meter Each 42.00
14.14 Dismantling wood work in frames, trusses, purlins and rafters upto 10
meter span and 5m height including stacking the material within 50m
lead
14.14.1 Of sectional area 40 Sq. cm. and above P.Cum 1006.00
14.14.2 Of sectional area below 40 Sq. cm. P.Cum 3.00
14.15 Add extra over item No. 14.14 for dismantling trusses rafters purlins
etc. of wood work for every additional span of one meter or part there
of beyond 10 Mtr.
14.15.1 Of sectional area 40 Sq. cm. and above P.Cum 141.00
14.15.2 Of sectional area below 40 Sq. cm. P.Cum 1.00
14.16 Add extra over item No. 14.14 for dismantling trusses rafters purlins
etc. of wood work for every additional height of one meter or part
there of beyond 5 Mtr.
14.16.1 Of sectional area 40 Sq. cm. and above P.Cum 202.00
14.16.2 Of sectional area below 40 Sq. cm. P.Cum 1.00
14.18 Dismantling steel work in built-up sections in angles, tees, flats and
channels etc. including all gusset plates, bolts, nuts, cutting, rivets,
weiding etc. including dismembering and stacking within 50 meters
lead.
P.Qtl. 129.00
14.19 Dismantling steel work in built-up sections without dismembering and
stacking within 50 meters lead.
P.Qtl. 87.00
14.2 Extra for dismantling trusses, rafters, purlins etc. of steel work for
every additional span of one meter or part there of beyond 10 meters.
P.Qtl. 20.00
14.21 Add extra item No. 14.18 and 14.19 for dismantling trusses rafters
purlins etc. of steel work for every additional hieght of one meter or
part three of beyond 5 Mtr.
P.Qtl. 20.00
14.22 Extra for making of structural steel work required to be re-erected.
P.Qtl. 105.00
ChapB-14 Page 83
CHAPTER : B-14
Chapter Description Unit Rate
Code No.
14.23 Dismantling tile work in floors and roofs laid in cement mortar
including stacking of serviceable material and disposal of
unserviceable material within 50 meter lead :
14.23.1 For thickness of tiles 10mm to 25mm P.Sqm 15.00
14.23.2 For thickness of tiles, above 25mm and upto 40mm P.Sqm 25.00
14.24 Dismantling dry brick pitching in floors drains etc. including stacking of
serviceable material and disposal of unserviceable material within 50
meters lead.
P.Cum 300.00
14.25 Dismantling brick tiles covering in terracing including stacking of
serviceable material and disposal of unserviceable material within 50
meters lead.
P.Sqm 22.00
14.26 Demolishing mud phuska in terracing and disposal of unserviceable
material within 50 meters lead.
P.Cum 206.00
14.27 Dismantling stone slab flooring laid in cement mortar including
stacking of serviceable material and disposal of unserviceable
material within 50 meters lead.
P.Sqm 60.00
14.28 Dismantling roofing including ridges, hips, valleys and gutters etc. and
stacking the material within 50 meter lead of :
14.28.1 G.I. Sheet P.Sqm 37.00
14.28.2 Asbestos Sheet P.Sqm 17.00
14.29 Dismantling stone slab roofing over wooden karries or RCC battens
(dismantling karries and battens to be paid for separately) including
stacking of serviceable material and disposal of unserviceable
material within 50 meter lead :
P.Cum 609.00
14.3 Dismantling Jack arch roofing and floors including stacking of
serviceable material and disposal of unserviceable material within 50
meter lead.
P.Sqm 57.00
14.31 Dismantling tiled roofing with battens boarding etc. complete including
stacking of serviceable material and disposal of unserviceable
material within 50 meter lead.
P.Sqm 46.00
14.32 Dismantling thatch roofing including mats bamboos, jafries etc.
complete including stacking of serviceable material and disposal of
unserviceable material within 50 meter lead.
P.Sqm 12.00
14.33 Dismantling wooden ballies in posts and struts including stacking
within 50 meters lead.
P.Rmt. 4.00
14.34 Dismantling and stacking within 50 meters lead fencing post, structs,
including earth work dismantling of concrete etc. in base of :
ChapB-14 Page 84
CHAPTER : B-14
Chapter Description Unit Rate
Code No.
14.35 Cutting ballies or wooden posts of fencing at the point of projection
above the concrete at ground and stacking the same within 50 meter
lead
Each 7.00
14.36 Dismantling barbed wire or flexible wire rope in fencing including
making rolls and stacking within 50 meter lead.
P.Qtl. 840.00
14.37 Dismantling wooden trellis work excluding frames but including
stacking the serviceable material within 50 meter lead.
P.Sqm 13.00
14.38 Dismantling expanded metal or IRC fabric with necessary battens and
beading including stacking the serviceable material within 50 meter
lead.
P.Sqm 15.00
14.39 Dismantling wooden boarding in lining of walls and partitions,
excluding supporting members but including stacking the serviceable
material within 50 meter lead.
14.39.1 Upto 10mm thick P.Sqm 13.00
14.39.2 Thickness above 10mm upto 25mm P.Sqm 15.00
14.39.3 Thickness above 25mm upto 40mm P.Sqm 21.00
P.Sqm 12.00
14.42 Dismantling CI or asbestos rain water pipe with fitting and clamps
including stacking the material within 50 meter lead :
14.42.1 75 mm to 80mm dia pipe P.Rmt. 9.00
14.42.2 100mm dia pipe P.Rmt. 10.00
14.42.3 150mm dia pipe P.Rmt. 10.00
ChapB-14 Page 85
CHAPTER : B-14
Chapter Description Unit Rate
Code No.
14.45 Dismantling steel cylinder, RC pipes etc. including excavation and
refilling trenches after taking out the pipes, breaking lead caulked
joints, melting of lead and making into block including stacking of
pipes, within a lead of 50 meter
14.45.1 Upto 60mm dia P.Rmt. 170.00
14.45.2 Above 600mm dia P.Rmt. 423.00
14.47 Taking out CI cover with frame from stone slab of man holes of
various sizes including dismantling of stone slab roofing and stacking
of useful materials near the site and disposal of unserviceable
materials within 50 meter lead.
Each 163.00
14.48 Taking out CI cover with frame from stone slab of man holes of
various sizes including dismantling of stone slab roofing and stacking
of useful materials near the site and disposal of unserviceable
materials within 50 meter lead.
Each 96.00
14.49 Dismantling of RCC spun vent shaft including excavating the cement
concrete pit completely, taking out the shaft, refilling the excavated
gap stacking the useful material near the site and disposal of
unserviceable materials within 50 meter lead.
Each 1080.00
14.5 Dismantling of gully chamber of various sizes incluidng CI grating with
frame including stacking of useful materials near the site and disposal
of unserviceable material within 50 meter lead including refilling the
gap.
Each 222.00
14.51 Dismantling of fushing cistern of any size including stacking of useful
materials near the site and disposal of unserviceable material within
50 meter lead.
Each 213.00
14.52 Dismantling of CI sluice value including stacking of usefull material
within a lead of 50 meter :
14.52.1 Upto 150mm dia Each 76.00
14.52.2 Above 150mm dia. Each 270.00
14.53 Dismantling of spindle fire hydrant including stacking of useful
material within 50 meter lead.
Each 160.00
14.54 Dismantling old plaster or skirting, raking out joints and cleaning the
surface for plaster including disposal of rubbish to the dumping
ground within 50 meter lead.
P.Sqm 12.00
14.55 Dismantling of stone masonry with care including stacking of
serviceable material and disposal of unserviceable material with in 50
mtr. Lead for :
14.55.1 Dry stone masonry P.Cum 132.00
ChapB-14 Page 86
CHAPTER : B-14
Chapter Description Unit Rate
Code No.
14.55.2 Stone masonry in mud mortar P.Cum 142.00
14.58 Dismantling chajja and shelves with care including making jhiries and
making good :
14.58.1 Katla Chajja P.Sqm 34.00
14.58.2 Marble shelves P.Sqm 103.00
14.58.3 RCC shelves P.Sqm 90.00
14.58.4 Stone shelves P.Sqm 90.00
14.58.5 RCC Chajja P.Sqm 55.00
14.59 Dismnantling CC jali including cost of making grooves in plaster and
making good.
P.Sqm 70.00
14.6 Dismantling marble dado, sides of pillars etc. with care.
P.Sqm 75.00
14.61 Dismantling aluminium / Gypsum partitions, doors, windows, fixed
glazing and false ceiling including disposal for unserviceable material
and stacking of serviceable material with in 50 meters lead as
directed by Engineer in charge
P.Sqm 14.00
14.62 Add extra for all type of dismantling work for each subsequent storey
or height more than 4.5m:
ChapB-14 Page 87
CHAPTER : B-13
REPAIRS TO BUILDINGS
CHAPTER : B-13
Chapter Description Unit Rate
Code No.
13.1 Repair to stone masonry in cement sand mortar 1 : 6 with old
Sqm 248.00
and new stone
13.2 Taking out decayed bricks from wall and replacing with new
ones set in :
13.2.1 Lime surkhi / sand mortar 1:2 Sqm 319.00
13.2.2 Cement sand mortar 1 : 6 Sqm 338.00
13.3 Repair to lime plaster in patches including removal of old
Sqm 159.00
plaster in regular shape and white or colour washing
13.4 Repair to cement plaster in cement mortar 1 : 6 (1 cement : 6
fine sand) including removal of old plaster in regular shape and Sqm 175.00
white or colour washing
13.5 Filling expansion joint with bitumen filler in plain or Reinforced
Mtr. 34.00
cement concrete 25mm width & 25mm deep
13.6 Crack filling in masaladar lime cement with water proofing
Mtr. 7.00
compound including jhiri
13.7 Cutting jhiri (recess) below 75mmx75mm in wall etc. and
Mtr. 37.00
making good
13.8 Cutting jhiri above 75mm x 75mm and below 150x150mm etc.
Mtr. 58.00
and making good
13.9 Scraping old surface and redoing lime loi or sandla Sqm 38.00
13.1 Lime plaster 1 : 2 under old stone slab with ad-mixture of gugal
gur. Etc.in three coats including dressing cutting of joints of
slab complete :
13.10.1 Proofing upto 25mm thickness Sqm 159.00
13.10.2 Proofing above 25mm & upto 60mm thickness Sqm 289.00
13.11 Cement plaster 1 : 3 under old stone slabs with ad-mixture
(gur, nails, binding wire to mesh and scraping scales &
dressing joints of slabs complete.
13.11.1 Proofing upto 25mm thickness Sqm 254.00
13.11.2 Proofing above 25mm & upto 60mm thickness Sqm 441.00
13.12 Patch repair to cement concrete floor including digging out old
floor in regular shape and removal of rubbish curing etc. Sqm 285.00
complete in all respects.
13.13 Washing floor with soda soap or other cleaning material Sqm 2.00
13.14 Removal and refixing stone chhajja 50 to 75mm thick including
Sqm 129.00
finishing, complete in all respects
13.15 Making opening in masonary wall including dismantling, fixing
lintel / beam and making good the damages to wall and floor
complete to match the existing surface including proping the Sqm 314.00
existing structue above the opening excluding cost of lintel /
beam etc.
13.16 Add extra item no. 13.15 for fixing of door / window frames
(Chowkhats or steel windows) in the opening including fixing
hold fast in cement concrete 1:3:6 (1 cement : 3 coarse sand : Sqm 120.00
6 stone grit 20mm nominal grade) excluding the cost of frame
or steel w
13.17 Renewing glass panes, with putty and nails wherever
necessary :
13.17.1 4mm thick plain glass panes Sqm 651.00
ChapB-13 Page 88
CHAPTER : B-13
Chapter Description Unit Rate
Code No.
13.17.2 5.5mm thick plain glass panes Sqm 857.00
13.18 Renewing glass panes with wooden fillets wherever necessary
13.24 Cutting jhiri for fixing slab and making good. Mtr. 78.00
13.25 Providing & fixing 25mm x 25mm angle iron upto 450mm long
fixed in CM 1 : 3 including cutting holes in walls and ceiling Each 92.00
making good the same complete as per design.
13.26 Making holes in stone masonry wall upto 450mm x 450mm size
Each 134.00
and making good in CM 1:6
13.27 Punching holes in flat bars in :
13.27.1 Below 15mm size Each 2.00
13.27.2 Above 15mm size Each 4.00
13.28 Guniting damaged RCC slab beams and columns for
strengthening with cement sand mortar 1 : 2 (1 cement : 2
sand) including preparing the surface, making "V" shaped
joints, cleaning the reinforcement bars with jet of potable water
and drying with compressed Sqm 2066.00
ChapB-13 Page 89
CHAPTER : B-13
Chapter Description Unit Rate
Code No.
13.30.3 1 Course (120 No. Carborundum stone) Sqm 13.00
13.30.4 1 Course (360 No. Carborundum stone) and polishing
Sqm 18.00
complete
13.31 Add extra for mirror polishing on marble work / stone work
Sqm 65.00
where ever required to give high gloss finish complete.
13.32 Add extra over item if external scaffolding to be used for repair
works
0.50
13.33 Providing and fixing of Aluminium at extruded corners of walls
of size 50x50x5mm including drilling, holes in tiles/ stone and
putting wooden/ PVC rawl plug of required size and counter
sunk steel screw at @300mm etc. on both baces of angles,
including gr
P.Rmt. 670.00
13.34 Labour charges for removing and refixing aluminium
partitions/door including minor repair and alteration in the
same.
P.Sqm 518.00
13.34 Labour charges for removing and refixing aluminium
partitions/door including minor repair and alteration in the
same.
P.Sqm 518.00
13.35 Repair of door, window shutters including cost of material
and labour for change of damaged :
(b) Panel by
ChapB-13 Page 90
CHAPTER : B-13
Chapter Description Unit Rate
Code No.
(i) Single Rubber Gutka Each 43.00
13.36 Labour charges for repair to door / window without using any
material such as applying randha (finishing) tightening of bolts
& screw etc.
P.Sqm 175.00
13.37 Repairing/ replacement of defective parts for door/ windows
with material, dry cleaning and refixing of vanishing blinds as
per direction of Engineer In Charge
P.Sqm 482.00
13.38 Making of hole in R.C.C. slab/wall/beams and masonary wall
(width up to 450 mm) by core cutting machine complete as per
direction of EI
ChapB-13 Page 91
CHAPTER B-12
FINISHING WORK
NOTE:
1- The rates are for complete work including racking of joints, curing, grinding, mixing and
2- finishing
The ratesTcover
& P and scaffolding
protection of allmaterial
places and cost of material
things, requiringwith all leadand
protection and cleaning
lift upto
floor three
such placeslevels.
and thing of all droppings and splashes of mortar etc.
3- Deduct 10% of the cost of lime mortar if gharat or mortar mill is not used for grinding.
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.1 Lime plaster on New surface on walls with lime surkhi mortar 1:2
(1 lime putty : 2 surkhi) including raking of joints, curing etc.
complete :
12.1.1 25 mm thick in 3 coats P.Sqm 160.00
12.1.2 20mm thick in 2 coats P.Sqm 130.00
12.1.3 12 mm thick in one coat P.Sqm 105.00
12.1.4 Add extra over item no. 12.1 for using admixture like Gur, Methi &
Gugal @ 1.0 Kg./each for every 10 Sqm of area including racking
of joints curing etc. complete
P.Sqm 90.00
12.2 Lime plaster on New surface on walls with lime sand mortar 1:2 (1
lime putty : 2 sand) including raking of joints, curing etc. complete
:
12.3 Lime plaster on New surface on walls with lime sand, surkhi
mortar 1:1:1 (1 lime putty : 1 sand : 1surkhi) including raking of
joints, curing etc. complete :
12.3.1 25 mm thick in 2.5 coats P.Sqm 170.00
12.3.2 20mm thick in 2 coats P.Sqm 134.00
12.3.3 12 mm thick in one coat P.Sqm 105.00
12.4 Araish plaster (1 lime puttly : 2 jhingra) over lime plaster back
ground
12.4.1 Add extra if colour is used P.Sqm 202.00
12.5 Applying Birla / JK white cement based putty over cement plaster
surface for making even surface.
P.Sqm 120.00
12.6 Applying plaster of Paris over cement plasper surface for making
even surface
P.Sqm 132.00
12.6 (A) Providing & laying POP moulding & beading in celling including
nalling & scaffolding etc. complete of size
(a) 25mm x 12 mm P.Rmt. 55.00
(b) 25mm x 25mm P.Rmt. 65.00
ChapB-12 Page 92
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.6 (B) Providing & laying POP Cornice of required design & pattern in
ceiling including nailing & scaffolding etc. complete with fine
finishing of size :
(a) 50mm x 50mm P.Rmt. 55.00
(b) 65mm x 65mm P.Rmt. 65.00
( c) 75mm x 75mm P.Rmt. 75.00
Cement Plaster
12.7 Plaster on new surface on wall in cement sand mortar 1:3
including raking of joints etc. complete fine finish :
12.7.1 25mm thick P.Sqm 259.00
12.7.2 20mm thick P.Sqm 202.00
12.7.3 12 mm thick P.Sqm 172.00
12.8 Plaster on new surface on walls in cement sand mortar 1:4
including raking of joints etc. complete fine finish
12.8.1 25mm thick P.Sqm 254.00
12.8.2 20 mm thick P.Sqm 224.00
12.8.3 12 mm thick P.Sqm 159.00
ChapB-12 Page 93
CHAPTER B-12
Chapter Description Unit Rate
Code No.
P.Sqm 12.00
12.15 Finishing with neat cement (punning)
P.Sqm 24.00
12.16 Fine finishing cost of cement plaster sandla with cement, marble
powder (passing through IS sieve 10) and lime mix 1:1:6 per
specification upto 4mm thick
P.Sqm 33.00
12.17 Deduct over item No. 12.8 to 12.12 if sandla is to be done on top
surface.
P.Sqm 5.00
12.18 Add extra item no. 12.1 to 12.12 for plaster done over ceiling
P.Sqm 0.20
12.19 Add extra over item no. 12.1 to 12.12 for plaster over spherical or
groin ceiling.
P.Sqm 0.25
12.2 Making grooves as per design in plaster 10mm to 20mm wide
12.20.2 Making of drip course (Tapka) in cement sand mortar 1:6 width
upto 40 mm and 10 mm thick as per approved design
P.Rmt. 4.00
12.21 Making lining out on plaster to imitate stone or concrete block
walling
P.Sqm 25.00
12.22 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine
sand)
P.Sqm 156.00
12.23 6mm thick cement plaster 1:3 ( 1cement : 3fine sand) finished with
a floating coat of neat cement and thick coat of Lime wash on top
of walls when dry for bearing of R.C.C slabs and beams.
P.Sqm 95.00
MISCELLANEOUS
ChapB-12 Page 94
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.29 Add extra over item no. 12.1 to 12.12 for plaster work on exterior
wall of height more than 4.5m from plinth level of every additional
height of 4.5 Mtr. Or part thereof.
P.Sqm 0.10
12.3 Add extra for plastering on circular work not exceeding 6 mtr. In
radius
P.Sqm 0.10
12.31 Add extra for plaster work for providing 12mm thick bend upto
30cm wide in cement sand mortar 1:4
12.31.1 Flush band P.Sqm 68.00
ChapB-12 Page 95
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.32 Rough cast plaster with a mixture of sand and gravel or crushed
stone 2.36mm to 12.5mm nominal size dashed over and including
the fresh plaster in two layer, under layers of 12mm thick cement
plaster and top layer 10mm thick of CM 1:4 (1cement :4 sand) mi
12.32.1 Under layer of 12mm thick cement plaster done in cement sand
mortar 1:4 (1 cement : 4 sand)
(a) Ordinary cement finish using ordinary cement P.Sqm 288.00
(b) Dark coloured finish using ordinary cement and required pigments P.Sqm 360.00
(c) Light coloured finish using white cement and required pigments P.Sqm 435.00
12.32.2 Under layer of 12mm thick cement plaster done in cement sand
mortar 1:3 (1 cement : 3 sand)
(a) Ordinary cement finish using ordinary cement P.Sqm 298.00
(b) Dark coloured finish using ordinary cement and required pigments P.Sqm 364.00
(c ) Light coloured finish using white cement and required pigments P.Sqm 441.00
SUPERIOR PLASTER
12.33 Add extra over item No. 12.32 for plaster with a mixture of washed
pebbles of crushed stone 5mm to 12.5mm nominal size instead of
gravel or crushed stone etc.
P.Sqm 23.00
12.34 Decorative plaster work with spectrum textured coating as per
approved colour and shade complete as per manufacturers
specifications.
12.34.5 PERKY-TEXTURED - (Brush Finish) av. thickness 152 to 200 P.Sqm 95.00
microns.
12.34.6 PERKY-FINE TEXTURED- (Roller Finish) av. thickness 400 to 500 P.Sqm 138.00
microns.
ChapB-12 Page 96
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.34.7 AMBROSIA TEXTURED- (Spray Finish) av. thickness 200 to 1000 P.Sqm 240.00
microns.
12.34.8 ORNATA TEXTURED- (Trowel Finish) av. thickness 1200 to 1500 P.Sqm 275.00
microns.
12.34.9 WALJWELS TEXTURED- (Trowel Finish) av. thickness 1000 to P.Sqm 240.00
1500 microns.
12.34.10 PADRON TEXTURED- (Trowel Finish) av. thickness 1500 to 2000 P.Sqm 300.00
microns.
12.34.11 PLACTION TEXTURED- (Trowel Finish) av. thickness 1500 to P.Sqm 325.00
2000 microns.
12.34.12 FLAKES TEXTURED- (Trowel Finish) av. thickness 800 to 1000 P.Sqm 400.00
microns.
POINTING
12.35 Pointing on stone masonry in lime sand mortar 1:2 (Lime putty : 2
sand)
ChapB-12 Page 97
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.4 Add extra item no. 12.35 to 12.39 on exterior walls of height more
than 4.5m from plinth level for every additional height of 4.5m or
part thereof
P.Sqm 0.10
P.Sqm 16.00
12.44 White washing with lime to give an even shade including all
scaffolding :
ChapB-12 Page 98
CHAPTER B-12
Chapter Description Unit Rate
Code No.
12.47.3 Old work (one or more coats) with whiting with a base coat of P.Sqm 8.00
white washing including scrapping old surface.
12.47.4 Old work (two or more coats) with whiting with a base coat of P.Sqm 7.00
white washing including scrapping surface.
12.47.5 Old work (one or more coats) with lime including scrapping P.Sqm 4.00
surface.
12.47.6 Old work (one or more coats) with whiting including scrapping P.Sqm 4.00
surface.
P.Sqm 4.00
ChapB-12 Page 99
CHAPTER B-12
Chapter Description Unit Rate
Code No.
DISTEMPER
12.51.1 New work (two or more coats) over and including scrapping and P.Sqm 67.00
priming coat with cement primer
12.51.2 old work (one or more coats) including scrapping surface and
necessary repairs.
(a) Colour Change P.Sqm 21.00
(b) Same Colour P.Sqm 14.00
CEMENT PAINT
12.53 Finishing wall with water proofing cement paint of approved brand
and manufacture and or required shade to give an even shade
including all scaffolding :
NOTE : The rates are for approved quality make paints confirming to I.S.
127-106, 341 and 340
12.55 Applying priming coat :
12.55.1 With ready mix pink or gray primer of approved brand and P.Sqm 30.00
manufacture on wood work hard and soft wood.
12.55.2 With ready mix Aluminium primer of approved brand and P.Sqm 28.00
manufacture on resinous wood and plywood
12.55.3 With ready mix Zink Chromate yellow primer of approved brand P.Sqm 25.00
and manufacture on steel galvanized iron/steel wire.
12.56 Painting with ready paint of approved brand and manufacture in all
shades to given an even shade :
12.57 Painting one thin coat with lead of approved brand and
manufacture on wet or patchy portion of plastered surfaces
P.Sqm 106.00
12.58 Painting on GI sheet with ready mixed paint of approved brand
and manufacture to give an even shade :
12.58.1 New work (Two or more coats) P.Sqm 48.00
12.58.2 Old work (one or more coats) white grey and green shade. P.Sqm 31.00
12.59 Painting (two or more coats) on rain water soil, waste and vent
pipes and fitting with black anticorrosive bitumastic paint of
approved brand and manufacture over and including a priming
coat of ready mixed zinc chromate yellow on new work :
12.59.1 50mm dia. Pipes P.Rmt. 15.00
12.59.2 75mm dia. Pipes P.Rmt. 20.00
12.59.3 100mm dia. Pipes P.Rmt. 26.00
12.59.4 150mm dia. Pipes P.Rmt. 37.00
12.6 Painting (one or more coats) on rain water soil, waste and vent
pipes and fitting with black anticorrosive bitumastic paint of
approved brand and manufacture on old work :
12.60.1 50mm dia. Pipes P.Rmt. 7.00
12.60.2 75mm dia. Pipes P.Rmt. 9.00
12.60.3 100mm dia. Pipes P.Rmt. 12.00
12.60.4 150mm dia. Pipes P.Rmt. 18.00
12.61 Painting (two or more coats) on rain water soil, waste and vent
pipes and fitting with Aluminium paint of approved brand and
manufacture over a priming coat of ready mixed zinc chromate
yellow primer on new work :
12.61.1 50mm dia. Pipes P.Rmt. 14.00
12.61.2 75mm dia. Pipes P.Rmt. 21.00
12.62 Painting (one or more coats) on rain water soil, waste and vent
pipes and fitting with Aluminium of approved brand and
manufacture on old work :
12.62.1 50mm dia. Pipes P.Rmt. 8.00
12.62.2 75mm dia. Pipes P.Rmt. 12.00
12.62.3 100mm dia. Pipes P.Rmt. 16.00
12.62.4 150mm dia. Pipes P.Rmt. 21.00
12.63 Painting with oil type wood preservative of approved brand and
manufacture :
12.63.1 New work (Two or more coats) P.Sqm 21.00
12.63.2 Old work (one or more coats) P.Sqm 16.00
12.64 Coat-tarring coats on new work using 0.16 and 0.12 litre of coal
tar per Sqm in the first and second coat respectively
P.Sqm 38.00
12.65 Coat-tarring one coat on old work using 0.12 litre of coal tar per
Sqm.
P.Sqm 19.00
12.66 Spray painting with flat wall paint of approved brand and
manufacture to give an even shade :
12.66.1 Two or more coats on new work including priming coat of P.Sqm 86.00
distemper primer of approved brand and manufacture.
12.66.2 Two or more coats on new work including priming coat of cement P.Sqm 82.00
primer of approved brand and manufacture.
12.66.3 On lod work (One or more coats) P.Sqm 34.00
12.67 Wall painting with plastic emulsion paint of approved brand and
manufacture to give an even shade :
12.67.1 Two or more coats on new work including preparation of base with P.Sqm 80.00
primer, putty, lippy complete in all respect.
12.67.2 One or more coats on old work P.Sqm 51.00
12.68 Painting with enamel paint of approved brand and manufacture to
give an even shade :
12.68.1 Two or more coats on new work P.Sqm 70.00
12.68.2 one or more coats on lod work P.Sqm 49.00
12.69 Painting with Aluminium paint of approved brand and manufacture
to give an even shade :
12.69.1 Two or more coats on new work P.Sqm 72.00
12.69.2 One or more coats on old work P.Sqm 45.00
12.7 Painting with acid proof paint of approved brand and manufacture
to required colour to give an even shade :
12.70.1 Two or more coats on new work P.Sqm 57.00
(a)
12.73.1 Two or more coats glue sizing with copal varnish over an under P.Sqm 33.00
coat of flatting varnish.
12.73.2 Two or more coats transparent wood filler copal varnish over an P.Sqm 32.00
under coat of flatting varnish.
12.73.3 One or more coats with copal varnish P.Sqm 30.00
12.73.4 Two or more coats transparent wood filler with sprey varnish over P.Sqm 58.00
an under coat of flatting varnish.
12.73.5 One or more coats with spray varnish P.Sqm 31.00
12.76 Bees waxing on wood work with local made wax polish :
12.76.1 New work in proportion 2 :15 : 1 : 0.50 (2-bees wax : 1.5-linseed P.Sqm 69.00
oil : 1-turpentine oil : 0.50-varnish by weight).
12.76.2 Old work in proportion 4 : 3 : 2 : 1 (4-bees wax : 3-linseed P.Sqm 35.00
oil : 2- Turpentine oil : 1-varnish by weight).
12.77 Polished on wood work with ready made wax polish of approved
brand and manufacture :
12.8 Painting (One or more coats) with black Japan paint of approved
brand and manufacture to give and even shades.
P.Sqm 25.00
12.81 Painting fire places and iron grating with paint of approved brand
and manufacture upto area 5 sqm
P.Sqm 148.00
12.82 Pink colour wash with khameera mixed with pigment including
making gota, gardana, Kangooras and ornamental lining work as
per approved Jaipur style and pattern, complete in all respects :
P.Sqm 97.00
12.84 Finishing wall with vinyl satin finish coating paints of approved
shade with two or more coats including sand papering, priming
coat, making surface with putty or plaster of Paris etc. complete in
all respects :
DUCO PAINTING
12.85 Painting on new surface with duco paint (IC or equivalent) to give
an even shade (minimum 4 coats) with preparation of surface by
rubbing, primer coats, duco filler putty including polishing etc.
complete :
12.85.1 On wood work P.Sqm 0.00
12.85.2 On steel work P.Sqm 0.00
12.87 Providing and applying superior quality wall painting with Velvet
touch emulsion paint of approved brand and manufacture to give
an even shade with putty and preparation of surface applying with
the help of paint roller the work complete in all respect as
12.88 Providing and applying superior quality Duco paint on wood work
like doors, windows etc. of approved brand and manufacture to
given an even shade including preparation of surface with primer
and putty complete in all respect with spray machine as per dire Sqm 2028.00
11.2 Extra for brick flooring laid in diagonal herring bone bond or
other pattern as specified.
P.Sqm 15.00
CEMENT CONCRETE FLOORING
11.3.1 25mm thick with 12.5mm thick nominal size aggregate. P.Sqm 218.00
11.3.2 40mm thick with 20mm thick nominal size aggregate. P.Sqm 296.00
11.3.3 50mm thick with 20mm thick nominal size aggregate. P.Sqm 316.00
11.3.4 75mm thick with 20mm thick nominal size aggregate. P.Sqm 429.00
11.4.1 25mm thick with 12.5mm thick nominal size aggregate. P.Sqm 142.00
11.4.2 40mm thick with 20mm thick nominal size aggregate. P.Sqm 200.00
11.4.3 50mm thick with 20mm thick nominal size aggregate. P.Sqm 232.00
11.4.4 75mm thick with 20mm thick nominal size aggregate. P.Sqm 345.00
P.Sqm 576.00
11.7 Cement plaster in skirting and/dado with cement mortar 1:3
(1 cement : 3 course sand) finished with a floating coat of
neat cement including rounding of junctions with floor :
11.8 40mm thick flooring with red oxide under layer 30mm thick
cement concrete 1:2:4 (1 cement : 2 course sand : 4 graded
stone aggregate 12mm nominal size) and top layer 10mm
thick plaster of cement red oxide mix using 3.5 Kg. of red
oxide of iron per 50Kg. o
P.Sqm 702.00
11.9 Add or deduct over item No. 11.8 for using more or less than
3.5 Kg. of red oxide of iron per 50 Kg. of cement in 40mm
thick red oxide flooring.
P.Sqm 30.00
11.1 Red oxide plaster/dado with top layer 6mm thick plaster of
cement red oxide of mix using 3.5Kg. of red oxide of iron per
50 Kg. of cement 1:3 (1 cement : 3 course sand) finished
with a floating coat of neat cement red oxide mix of same
proportion :
11.10.1 18mm thick with under layer 12mm thick cement plaster 1:3 P.Sqm 355.00
(1 cement : 3 coarse sand).
11.10.2 21mm thick with under layer 15mm thick cement plaster 1:3 P.Sqm 370.00
(1 cement : 3 coarse sand).
11.11 Add or deduct over item No. 11.10 for using more or less
than 3.5Kg. of red oxide of iron per 50Kg. of cement in
18mm or 21mm thick red oxide plaster skirting/dado.
P.Sqm 21.00
11.12 Cement concrete pavement of required thickness with.
(a) 1:2:4 (1-Cement:2-course sand : 4-graded stone
aggregate 20 mm nominal size) including finishing complete.
P.Cum 5048.00
P.Cum 5517.00
11.13 Extra for making chequers of approved pattern on cement
concrete floors, steps landing, pavement etc.
P.Sqm 19.00
11.14 Filling of sunk portion of roof with earthen pots of required
height including filling voids with 1:2:4 light concrete, using
brick bats complete levelling and dressing the surface by
50mm thick cement concrete 1:2:4 as per specification.
P.Sqm 1640.00
TERRAZZO FLOORING
11.15 40mm thick marble chips flooring rubbed and polished to
granolithic finish under layer 34mm thick cement concrete
1:2:4 (1 cement : 2 course sand : 4 graded stone aggregate
12.5mm nominal size) including fixing of dividing strip
(excluding the cost of str
11.19.1 18mm thick with under layer of 12mm thick cement plaster
1:3 (1 cement : 3 coarse sand) :
(a) Ordinary cement without any pigment. P.Sqm 454.00
(b) Light shade pigment with ordinary cement. P.Sqm 483.00
(c) Medium shade pigment with approximately 50% white P.Sqm 510.00
cement and 50% ordinary cement.
(d) White cement without any pigment. P.Sqm 516.00
(e) Light shade pigment with white cement. P.Sqm 538.00
(f) Dark shade pigment with ordinary cement. P.Sqm 471.00
11.19.2 21mm thick with under layer of 15mm thick in cement plaster
1:3 (1 cement : 3 coarse sand) :
11.19.3 25mm thick with under layer of 19mm thick in cement plaster
1:3 (1 cement : 3 coarse sand) :
P.Rmt. 1.00
11.26 Add extra for making moulded nosing in terrazzo including
returned moulded ends and angles to mouldings.
P.Rmt. 60.00
11.27 Special surface finishing to treads risers at the end of
concrete steps and the like including form work.
P.Sqm 34.00
11.30.6 Add extra over item No. 11.30.1 to 11.30.3 for using 24mm
thick terrazo tiles with marble chips of size upto 10mm
instead of 20mm thick terrazzo tiles with marble chips of size
upto 6mm
P.Sqm 52.00
11.31 Precast terrazzo tiles of approved make 20mm thick with
marble chips of size upto 6mm in skirting & risers, treads of
steps and dados 12mm thick cement plaster 1:3 (1 cement :
3 coarse sand) jointed with neat cement slurry mixed with
pigment to match the
11.32.4 Add extra for using 30mm thick chequereed terrazzo tiles
instead of 22mm thick terrazo tiles.
P.Sqm 52.00
11.33 Providing & laying Chequered plain cement concrete
embossed o specially manufactured non-slipping tiles of
approved make 20mm thick laid on 20mm thick bed of
cement mortar 1:6 jointed with neat cement slurry complete.
11.35 Polished Blue Kota Stone flooring skirting, laid over 20mm
thick base of C.M. 1:4 and jointed with grey cement slurry to
match the shade of the slab including rubbing and polishing
complete :
11.37.1 20mm thick slab area upto 900 Sq.Cm. P.Sqm 800.00
11.37.2 25mm thick slab area 901 to 2000 Sq.Cm. P.Sqm 880.00
11.37.3 30mm thick slab area 2001 to 5000 Sq.Cm. P.Sqm 1019.00
11.37.4 Deduct from item No. 11.35 to 11.37 for using Kota stone
other than blue in colour.
P.Sqm 110.00
11.39 20mm thick polished stone for steps risers, skirting, dados,
wall & pillars laid on 12mm thick base of CM. 1:3 & jointed
with grey cement including rubbing & polishing :
11.46 Rough chisel dressed stone flooring over 20mm (Av.) thick
base in CM 1:6 including pointing with cement mortar 1:2 (1
cement : 2 stone dust) with and admixture of pigment to
match the shade of stone with joint thickness upto 15mm:
11.48 Coursed Stone paving set in CM 1:6 laid over a bed of 20mm
thick cement sand mortar 1:6 with cement pointing 1:3 :
11.5 Providing and fixing Polyvinyl Chloride sheet/ P.V.C. tile (with
backing of Hessian cloth or other woven fabric flooring using
rubber base adhesives including rolling with light wooden
roller complete :
11.51.4 Add extra over item No. 11.51.3 for antistatic flooring:
P.Sqm 10.00
11.52 Add extra over item No. 11.35 and 11.38 for combination
flooring of Blue Kota and Marble stones :
11.52.1 Using upto 10% marble stone. P.Sqm 40.00
11.52.2 Using above 10% and upto 15% marble stone. P.Sqm 62.00
11.52.3 Using above 15% and upto 20% marble stone. P.Sqm 85.00
WOODEN FLOORING
P.Sqm 6869.00
11.55 Providing and fixing metal strips of 1.6mm thickness at the
junction with other floors :
11.57.2 Add extra over item no. 11.57.1 for 80 mm thick blocks
P.Sqm 150.00
11.57.3 Add extra over item no. 11.57.1 for 100 mm thick blocks
P.Sqm 271.00
2- The rates for A.C. and G.I. sheet roofing are inclusive of all necessary, overlaps and
wastage in cutting and all standard screws nuts washers bolts and nuts ‘J’ or ‘L’
hooks etc. required as per specifications.
3- All precautions shall be taken to ensure that the finished roof is water tight and
without any leakage under all weather conditions. Particular care shall be taken in
providing good workmanship specially at vulnerable points.
CHAPTER B-10
Chapter Description Unit Rate
Code No.
ROOFING
STONE SLAB ROOFING
10.1 Stone slab roofing on ground floor with fine grained stone
slab from approved quarry including filling of joints of parapet
and slab on both sides in cement sand mortar 1:4, ralthal,
stone kharanja, lime terracing 90mm average thickness [as
per JAIPUR PRA
P.Sqm 300.00
10.5 Add extra over item No. 10.4 for additional thickness above
90mm average for each 10mm extra thickness.
P.Sqm 21.00
10.6 Add extra over item No 10.4 or 10.5 for each subsequent
storey for thickness.
10.1 Providing and laying brick tiles of class designation 100 over
mumty, roofs, grouted with cement mortar 1 : 3 mix with 2%
of integrated water proofing compound by wt. Of cement
over 12mm thick layer of cement mortar 1 : 3 and finished
neat.
P.Sqm 225.00
10.11 Providing brick kharanja in lime sand mortar 1 : 2 in square
pattern over roof of ground floor :
Each 275.00
10.13 Add extra over item No. 10.12 for every additional 1 Cm
thickness of mud phuska.
Sqm 5.00
Sqm 240.00
10.15 Encasing of R.S. joist with cement concrete (1 : 3 : 6)
including expended metal of B.B. lathing finished with
cement rendering.
P.Sqm 220.00
10.16 Encasing of R.S. Joist with khanda/bricks in cement mortar
1:4 with neat finishing
P.Sqm 250.00
10.17 Providing stone slab covering over drains including filling of
joints in cement sand mortar 1 : 3 with 35mm thick cement
concrete flooring 1 : 2 : 4 mix complete with good finish with :
10.2 Crazy marble stone flooring 20mm thick marble stone over
roof in ordinary cement with black or of specified color
topping including filling the gaps with cement marble chips
mix in proportion of 4 : 7 (4cement : 7 white black or white or
black marble chip
P.Sqm 475.00
10.21 Finishing with 25mm thick cement plaster on roofs in cement
sand mortar 1 : 4 mix including water proofing compound @
2% of cement used, with neat cement, finishing, curing etc.
complete in all respect including making of 300 mm x 300
mm square.
P.Sqm 182.00
10.22 Providing Cement based water proofing treatment to RCC
Roof with brick bats 25 mm to 100 mm in CM 1:4 (1-
Cement : 4-Sand) the under layer being 20mm thick bed
plaster of cement sand mortar 1:6 with neat cement punning
@ 3 Kg/sqm including cleaning of RCC
P.Sqm 425.00
10.23 Providing props & rafters (Ballies & fantas at lower roof at the
time of execution of work in upper floors in multi storey
building. The spacing of grid shall not exceed 1 Mtr. x 1 Mtr.
(Rates are for one Month)
P.Sqm 41.00
10.24 Making khurras 450 x 450mm with average minimum
thickness 50mm cement concrete 1 : 2:4 over P.V.C. Sheet 1
Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1
: 3 and one coat of neat cement, rounding edges and making
and finishing the out let co
Each 130.00
10.26 Add extra over item No. 10.25 for providing and fixing CGI
sheets vertically or to a pitch exceeding 60o
P.Sqm 4.00
10.27 Add extra over item No. 10.25 for providing and fixing CGI
sheets in curved roofing
P.Sqm 4.00
10.28 Extra for Straight cutting in CGI sheet roofing for making
opening of area exceeding 40 dm2 for chimney stack, sky
light etc.
P.Rmt. 34.00
10.29
FALSE CEILING
10.4 Providing and fixing chir wood frame work for false ceiling of
net work of 600mm x 600mm approximately of batten size
60mm x 60mm as main rafters and 50 x 25mm as secondary
rafters with 10mm dia M.S. hangers at suitable intervals,
including coating of ant
P.Sqm 553.00
10.41 Providing and fixing 15 to 18 mm thick false ceiling tiles of
plaster of Paris as per approved design over wooden frame
with Brass screws complete in all respects including fixing of
exposed surface smooth with plaster of paris (excluding the
cost of wood
10.41.1 Plain tiles . P.Sqm 961.00
10.43 Providing and Fixing at all height all false ceiling of 12.5mm
thick tapered edge Gypsum board conforming to IS : 2095
including providing and fixing of frame work made of special
section power pressed from M.S sheet and galvanized in
accordance with zinc
P.Sqm 1370.00
10.44 Thatch roofing 100 to 150mm thick in two layers with
bamboos rafters and sleepers in both directions and laying
complete.
P.Sqm 362.00
10.45 Single country tiles roofing including hips & ridges complete
over wooden batten or bamboos.
P.Sqm 249.00
10.46 Add extra over item No. 10.45 if Mangalore tiles are used in
place of country tiles.
P.Sqm 110.00
10.47 Add over item Nos. 10.45 and 10.46 if aluminium tees are
provided.
P.Sqm 66.00
10.48 P & F of plastic ceiling tiles with adhesive complete of
dimension of 600 x 300 as per approved design including
cleaning of surface by wire brush and filling of uneven
surface by putties etc. complete including scaffolding
complete.
P.Sqm 691.00
10.49 P & F of wall paper with adhesive as per approved design
and make including cleaning the surface by wire brush of
filling uneven surface by putties etc. complete including
scaffolding complete (for estimate purposes).
P.Sqm 495.00
10.5 P & F Plain Fiber glass sheet ( FRP sheet fiber
Reinforcement product sheet confirming to IS:12866-1989
having minimum thickness as below Including fixing with nuts
,bolts hooks and bitumen washer etc complete.
10.51 Add extra for corrugated Fiber glass sheet as per Asbestos
cement profile/ steel profile over item No 10.50
0.15
10.52 Providing and fixing stainless steel ( Grade 304) railing made Kg. 457.00
of Hollow tubes, channels, plates etc., including welding,
grinding, buffing, polishing and making curvature (wherever
required) and fitting the same with necessary stainless steel
nuts and bo
10.53.1 GI Metal Ceiling Lay in Plain Tegular edge Global white Sqm 1420.00
colour tiles of size 595X595 mm, and 0.5 mm thick with 8
mm drop, made of G I Sheet having galvanizing of 100
gms/sqm (boths ides inclusive) and electro statically
polyester powder coated of thickne
10.53.2 GI Metal Ceiling Lay in perforated Tegular edge global white Sqm 1536.00
colour tiles of size 595x595mm and 0.5 mm thick with 8 mm
drop made of GI Sheet having galvanizing of 100 gms/ sqm
(both sides inclusive) and 20% perforation area with 1.8 mm
dia holes and havin
10.54 Providing & Fixing of Mineral Fibre Anti Bacterial Suspended Mtr 1561.00
Ceiling System with Bioguard (Bevelled Tegular) EDGE
TILES WITH 15 mm Exposed GRID. The tiles should have
Humidity Resistance (RH) of 95% Light Reflectance 90%,
Thermal Conductivity K =0.052-0.0
1479.00
10.57 Providing and fixing of perforated Metal Tile Ceiling System Sqm 3432.00
comprising of Tile of 600mm wide and 600mm long
manufactured out of 0.7mm thick aluminium alloy 3105 with
beveled edge of 4.15mm width height of 32mm. The tiles
shall be perforated to 1.
10.58 Providing and fixing of Un-perforated Metal Tile Ceiling Sqm 2896.00
System comprising of Tile of 600mm wide and 600mm long
manufactured out of 0.7mm thick aluminium alloy 3105
with beveled edge of 4.15mm width height of 32mm. The
Tile will be manufactured o
10.59 Providing and fixing of Un perforated Antibacterial Metal Tile Sqm 3743.00
Ceiling System comprising of Tile of 600mm wide and
600mm long manufactured out of 0.7mm thick aluminium
alloy 3105 with beveled edge of 4.15mm width height of
32mm. The Tile will be
10.6 Providing and fixing of Unperforated Metal Tile Ceiling Sqm 3068.00
System comprising of Tile of 600mm wide and 600mm long
manufactured out of 0.5mm thick Galvanised Iron with
beveled edge of 4.15mm width height of 32mm. The tiles
shall be perforated to 1.5mm
10.61 Providing and fixing of Unperforated Metal Tile Ceiling Sqm 2313.00
System comprising of Tile of 600mm wide and 600mm long
manufactured out of 0.5mm thick Galvanised Iron with
beveled edge of 4.15mm width height of 32mm. The tiles
shall be plain. The Tile wil
10.62 Supply & Fixing of torsion spring Plank Ceiling System, Sqm 4775.00
comprising of Plank of 600mm wide and 600mm long
manufactured out of 0.7mm thick Aluminium Alloy 3105
perforated 1.5mm dia With 22% open area. The metal ceiling
panels shall be downward accessible
10.63 Supply & Fixing of torsion spring Plank Ceiling System, Sqm 4697.00
comprising of Plank of 600mm wide and 600mm long
manufactured out of 0.7mm thick Aluminium Alloy 3105
perforated 1.5mm dia With 22% open area. The metal ceiling
panels shall be downward accessible
10.64 Supply & Fixing of torsion spring Plank Ceiling System, Sqm 4047.00
comprising of Plank of 600mm wide and 1200mm long
manufactured out of 0.6mm thick GALVANISED IRON
perforated 1.5mm dia With 22% open area. The metal ceiling
panels shall be downward accessible with
9.6 Add extra over item No. 9.1 to 9.5 for hoisting and fixing for P.Kg. 0.65
every additional one metre or part thereof beyond 4.5 mtr
height.
9.8 Drilling holes in rails, joist or M.S. plate. Each Hole 13.00
P.Kg. 88.00
9.14 Providing and fixing pressed steel mitred door frames
manufactured from commercial mild steel sheet of 1.25mm
(16 gauge) thickness including hinges jamb, lock jamb, head
and if required angle threshold of mild steel angle of section
50x25mm, or base ties
P.Kg. 114.00
P.Kg. 88.00
9.19.1 Add extra if square,rectangular hollow tubelar sections are
used
P.Kg. 13.00
P.Sqm 2975.00
9.22 Providing and fixing 1mm thick M.S. sheet garrage door
shutters with frame of 40 x 40 x 6mm. angle iron 3mm M.S.
gusset plates at the junction and corners including all fittings
and applying a coat of approved steel primer : (Excluding
cost of frames)
P.Sqm 2800.00
9.22.3 Using flats 30 x 6mm for diagonal braces and central cross
piece.
P.Sqm 2750.00
9.23 Supplying and fixing rolling shutters of approved make, made
of 80 x 1.25mm. M.S. laths interlocked together through their
entire length and jointed together at the end by end locks
mounted on specially designed pipe shaft with brackets, side
guides and a
P.Sqm 2050.00
9.24 Providing & fixing ball bearing for rolling shutters
Each 330.00
9.25 Add extra over item No. 9.23 for providing mechanical device
chain and crank operation for operating rolling shutters.
9.25.1 Exceeding 10.00 Sqm and upto 16.80 Sqm in the area.
P.Sqm 550.00
9.25.2 Exceeding 16.80 Sqm in the area.
P.Sqm 600.00
9.26 Providing and fixing M.S. sheet single leaf door shutter in
angle iron frame 35x35x5mm suitabilly diagonally braced
with 25x3mm flat iron above and below lock rail of size
50x5mm beading extra including all fittings, as per direction
of Engg. incharge but
Note:- Add extra over item No. 9.21,9.22, 9.23, 9.26 for using P.Sqm 105.00
G.I. Sheets instead of M.S. Sheets
9.27.3 Deduct from item No. 9.27.1 & 9.27.2 for providing 14 mesh P.Sqm 90.00
x 24 guage wire gauge instead of 4mm thick plain float glass.
9.29.1 Providing brass handles/peg stays and fittings in place of P.Sqm 70.00
oxidized fitting
9.29.3 5mm thick plain glass instead of 4mm thick plain glass P.Sqm 100.00
9.30.2 Pin headed 4mm thick glass panels is used instead of 4mm P.Sqm 40.00
thick plain glass
P.Sqm 218.00
9.34 Providing and fixing bright finished brass casement window
handles / fasteners of minimum weight 200 grams to side
hung steel windows with necessary welding and machine
screws etc. complete.
Each 68.00
9.35 Providing and fixing bright finished brass peg stays 300 mm
long of minimum weight 330 grams. to side hung steel
windows with necessary welding and machine screws etc.
complete.
Each 101.00
9.36 Providing and fixing bright finished brass peg stays to steel
ventilators with necessary welding and machines screws etc.
complete :
P.Sqm 2159.00
9.39 Deduct from item Nos. 9.28 & 9.38 if section used is not as
per I.S. 1038 (revised)
P.Sqm 15.00
9.44 Providing and fixing M.S. round holding bolts with nuts and
washers complete.
P.Kg. 64.00
9.45 Supplying of M.S. holdfast (40mmx3mm) over all length 45
cm with splitted (end) for doors and windows as per design.
Each 42.00
P.Rmt. 1550.00
9.48 Cast iron moulding fixing work in gate covers for fencing post
etc.
P.Kg. 60.00
(METAL PRESSED DOORS/WINDOWS)
P.Sqm 3213.00
9.5 Supplying and fixing of steel doors with frame of hollow metal
pressed section (80 x 50mm) of 1.25mm thick with single
sheet shutter having thickness 0.80mm M.S. sheet to be
spoet welded and embossed with rib type design front
vertical including hold fast
P.Sqm 2807.00
9.51 Supplying and fixing of Steel windows made out (65 x
40mm), hollow metal pressed section of 1.25mm thick sheet
F4 & F7 standard rolled section conforming to IS 1038 with
wholly openable shutter of 0.80 mm thick (out side & inside)
opening C.R. sheet embos
P.Sqm 3523.00
9.52 Supplying & fixing of M.S. louvered ventilators made out of
65 x 40mm hollow metal pressed section 1.25mm thick sheet
and louver 60mm wide, 1.25mm thick at angle of joints
mitred and flush welded with suitable steel lugs etc. complete
including applying p
P.Sqm 2400.00
FENCING WORK
9.55 180cm high fencing with angle iron post 55x55x6mm. placed
at every 3Mtr. apart 45cm. in ground embedded in cement
concrete 1:3:6 (30x30x60cm) corner and every tenth post to
be strutted with 55x55x6mm. angle iron provided with 6
horizontal lines and two di
P.Rmt. 506.00
P.Rmt. 460.00
P.Rmt. 420.00
P.Rmt. 316.00
9.59 Add or deduct for each wire line on item No. 9.55 to 9.58.
P.Rmt. 12.00
9.6 Add or deduct for additional or less hight per 10cm, on item
No. 9.55 to 9.58.
P.Rmt. 22.00
9.61 Add for using galvanized barbed wire instead of black
barbed wire
P.Rmt. Each 3.00
wire
9.62 Supplying and fixing of chain link fencing with angle iron
posts 50x50x6mm placed at every 3 Mtr. apart 30cm in
ground embedded in cement concrete 1:3:6 (30x30x45cm)
corner and every tenth post to be strutted with (50 x 50 x
6cm) angle iron provided and f
9.63 Supply & fixing of steel window made out 75x40 mm hollow
metal pressed section of 16 gauge thick sheet partly
openable and partly fixed panel shutter with 5 mm thick plain
glass panes outside openable and wire gauge 14x24 gauge
inside openable shutter wit
P.Sqm 3748.00
9.64 Providing & fixing stainless steel railing with 75cm height
from floor with 75mm OD main post where necessary with
40mm OD post with 90cm distance at stair with 50mm OD
top railing pipe with fitting in all respect. As per direction of
engineer in charge.
P.Rmt. 2860.00
Ch. Description Unit Wood 12 mm thick 9 mm thick 12 mm thick 12 mm thick 9 mm 12 mm thick 9 mm thick 4 mm thick Wire gauge 24 12 mm thick
Code grade-I teak ply teak ply particle shuttering thick commercial ply commercial ply plain glass gauge 14 mesh of teak ply
No. panels (both faces (both faces board panels ply shuttering (both faces (both faces panels IS designation 85 (one face
panels) panels) (Urea boned) (both faces ply (both panels) (Urea panels) (Urea gauge wires of dia panels)
panels) faces bonded) bonded) 0.56 mm panels
panels)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
8.6.1 25 mm thick
(A) Nigeria teak wood grade - I Sqm. 2667.00 3138.00 3019.00 2938.00 2602.00 2577.00
(B) Ghana teak wood grade - I Sqm. 2516.00 3024.00 2869.00 2787.00 2488.00 2463.00
(C) Sheesham wood grade - I Sqm. 2703.00 3195.00 2894.00 2812.00 2588.00 2542.00
(D) Hollock wood grade - I Sqm. 2415.00 2948.00 2769.00 2686.00 2412.00 2387.00
8.6.2 30 mm thick
(A) Nigeria teak wood grade - I Sqm. 2961.00 3477.00 3344.00 3095.00 3145.00 3292.00 3018.00 3210.00 2808.00 2783.00 3354.00
(B) Ghana teak wood grade - I Sqm. 2779.00 3298.00 3208.00 2959.00 3009.00 3113.00 2882.00 3030.00 2672.00 2647.00 3175.00
(C) Sheesham wood grade - I Sqm. 3051.00 3328.00 3411.00 3101.00 3212.00 3142.00 3085.00 3061.00 2837.00 2791.00 3205.00
(D) Hollock wood grade - I Sqm. 2657.00 3178.00 3117.00 2868.00 2918.00 2993.00 2791.00 2911.00 2581.00 2556.00 3055.00
8.6.3 35 mm thick
(A) Nigeria teak wood grade - I Sqm. 3166.00 3749.00 3549.00 3300.00 3350.00 3563.00 3223.00 3481.00 3013.00 2988.00 3611.00
(B) Ghana teak wood grade - I Sqm. 2963.00 3540.00 3392.00 3143.00 3193.00 3355.00 3066.00 3274.00 2856.00 2831.00 3417.00
(C) Sheesham wood grade - I Sqm. 3268.00 3575.00 3628.00 3348.00 3429.00 3390.00 3302.00 3308.00 3084.00 3038.00 3452.00
(D) Hollock wood grade - I Sqm. 2827.00 3401.00 3287.00 3038.00 3088.00 3216.00 2961.00 3134.00 2751.00 2726.00 3279.00
8.6.4 40 mm thick
(A) Nigeria teak wood grade - I Sqm. 3585.00 4021.00 3505.00 3555.00 3428.00 3218.00 3193.00 3816.00
(B) Ghana teak wood grade - I Sqm. 3349.00 3784.00 3327.00 3377.00 3250.00 3040.00 3015.00 3638.00
(C) Sheesham wood grade - I Sqm. 3705.00 3823.00 3595.00 3645.00 3518.00 3308.00 3283.00 3700.00
(D) Hollock wood grade - I Sqm. 3189.00 3767.00 3207.00 3257.00 3130.00 2920.00 2895.00 3518.00
8.6.5 45 mm thick
(A) Nigeria teak wood grade - I Sqm. 3791.00 4271.00 3761.00 3634.00 3424.00 4022.00
(B) Ghana teak wood grade - I Sqm. 3533.00 4027.00 3561.00 3434.00 3224.00 3822.00
(C) Sheesham wood grade - I Sqm. 3921.00 4071.00 3861.00 3734.00 3524.00 3947.00
(D) Hollock wood grade - I Sqm. 3359.00 3850.00 3427.00 3300.00 3090.00 3688.00
8.6.6 50 mm thick
Ch. Description Unit Wood 12 mm thick 9 mm thick 12 mm thick 12 mm thick 9 mm 12 mm thick 9 mm thick 4 mm thick Wire gauge 24 12 mm thick
Code grade-I teak ply teak ply particle shuttering thick commercial ply commercial ply plain glass gauge 14 mesh of teak ply
No. panels (both faces (both faces board panels ply shuttering (both faces (both faces panels IS designation 85 (one face
panels) panels) (Urea boned) (both faces ply (both panels) (Urea panels) (Urea gauge wires of dia panels)
panels) faces bonded) bonded) 0.56 mm panels
panels)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
8.9.1 25 mm thick.
(A) Nigeria teak wood grade - I Sqm. 2645.00 2959.00 2918.00 2863.00
(B) Ghana teak wood grade - I Sqm. 2507.00 2845.00 2949.00 2949.00
(C) Sheesham wood grade - I Sqm. 2665.00 3011.00 2792.00 2738.00
(D) Hollock wood grade - I Sqm. 2414.00 2769.00 2666.00 2612.00
8.9.2 30 mm thick.
(A) Nigeria teak wood grade - I Sqm. 2910.00 3313.00 3165.00 2999.00 3033.00 3190.00 2948.00 3136.00 3207.00
(B) Ghana teak wood grade - I Sqm. 2743.00 3133.00 3029.00 2863.00 2897.00 3010.00 2812.00 2956.00 3052.00
(C) Sheesham wood grade - I Sqm. 2985.00 3163.00 3232.00 3013.00 3100.00 3041.00 3015.00 2986.00 3082.00
(D) Hollock wood grade - I Sqm. 2632.00 3015.00 2938.00 2772.00 2806.00 2892.00 2721.00 2837.00 2932.00
8.9.3 35mm thick.
(A) Nigeria teak wood grade - I Sqm. 3115.00 3578.00 3370.00 3204.00 3238.00 3461.00 3153.00 3407.00 3412.00
(B) Ghana teak wood grade - I Sqm. 2927.00 3377.00 3213.00 3047.00 3081.00 3254.00 2996.00 3200.00 3255.00
(C) Sheesham wood grade - I Sqm. 3209.00 3412.00 3449.00 3260.00 3317.00 3289.00 3232.00 3233.00 3329.00
(D) Hollock wood grade - I Sqm. 2802.00 3238.00 3108.00 2942.00 2976.00 3115.00 2891.00 3061.00 3150.00
8.9.4 40 mm thick.
(A) Nigeria teak wood grade - I Sqm. 3463.00 3783.00 3409.00 3443.00 3358.00 3617.00
(B) Ghana teak wood grade - I Sqm. 3246.00 3605.00 3231.00 3265.00 3180.00 3439.00
(C) Sheesham wood grade - I Sqm. 3573.00 3660.00 3499.00 3533.00 3448.00 3577.00
9 mm thick
teak teak
ply
(one face
panels)
15
3138.00
3013.00
3038.00
2912.00
3344.00
3208.00
3286.00
3117.00
3549.00
3392.00
3533.00
3287.00
under.
9 mm thick
teak teak
ply
(one face
panels)
15
2959.00
2845.00
2888.00
2763.00
3165.00
3029.00
3137.00
2938.00
3370.00
3213.00
3385.00
3108.00
under.
9 mm thick
teak teak
ply
(one face
panels)
15
3372.00
3489.00
3421.00
3291.00
3568.00
3708.00
3685.00
3475.00
3764.00
3928.00
3960.00
4147.00
4214.00
3836.00
4157.00
4366.00
4471.00
4017.00
4343.00
4585.00
4702.00
4198.00
8.2 Supplying and fixing wood work in frames of wall panelling, false
ceiling partition wall etc. as per approved design and drawing
including antitermite treatment.
8.3 Deduct from item Nos. 8.1 and 8.2 if inferior than Grade - I wood is
used.
0.20
8.4 Add extra over item no. 8.1 for wood work for stair case railing.
0.10
8.5 Add extra in frames for circular members such as in fan lights,
staircase railing etc.
0.10
8.6 Table 8A
8.7 Add extra over item No. 8.6 for :
8.7.1 Using phenol bonded exterior grade particle board instead of Urea
bonded, in column No. 7.
P.Sqm 25.00
8.7.2 One side teak face particle board, in column No.7
P.Sqm 166.00
8.7.3 Both sides teak face particle board, in column No. 7
P.Sqm 249.00
8.7.7 Using medium density fibre board one side laminated face instead
of particle board, in column No. 7
(a) Interior grade
P.Sqm 172.00
(b) Exterior grade
P.Sqm 215.00
7.7.8 Using medium density fibre board both side laminated face instead
of particle board, in column No. 7
(a) Interior grade
P.Sqm 249.00
(b) Exterior grade
P.Sqm 374.00
8.7.9 Using thicker panels than 12mm, in column No. 7, for doors of
thickness 40mm and above.
8.8.1 Using A.C. sheet/ Flexo board 6mm thick for doors of thickness
25mm and 30mm, in column No. 11.
P.Sqm 33.00
8.8.2 Using pin-head glass instead of 4mm thick plains glass, in column
No. 12 :
P.Sqm 40.00
8.8.3 Providing Single leaf shutter instead of double leaf.
8.9 Table 8A
8.1 Add extra over item No. 8.9 for :
8.10.1 Using Phenol bonded exterior grade particle board instead of urea
bonded in column No. 7.
P.Sqm 17.00
8.10.2 One side teak face particle board in column No. 7.
P.Sqm 110.00
8.10.3 Both side teak face particle board in column No. 7
P.Sqm 167.00
8.10.4 One side laminated face particle board in column No.7.
P.Sqm 134.00
8.10.9 Using thicker panels than 12mm in column No. 7. for door
thickness 40mm & above.
8.10.10 Add extra for providing Nigeria / Ghana Teak wood grade - I fixed
louvers instead of glazing in column No. 4 for Nigeria / Ghana teak
wood door shutter.
P.Sqm 80.00
8.10.11 Add extra for providing Nigeria / Ghana Teak wood grade - I
movable louvers instead of glazing in column No. 4 for Nigeria /
Ghana teak wood shutter.
P.Sqm 100.00
8.11 Deduct from item No. 8.9 for :
8.11.1 Using (A.C. Sheet/ Flexo board) 6mm thick for doors of thickness
25mm and 30mm thick in column No. 11.
P.Sqm 20.00
8.11.2 Using Pin head glass instead of 4mm thick plain glass for all type
of doors.
P.Sqm 19.00
8.11.3 Providing Single leaf shutter instead of double leaf.
P.Sqm 0.20
8.12 Table 8A
8.13 Delete
8.14 Add extra over item No. 8.12 and 8.13 for
8.14.1 Using Phenol bonded exterior grade particle board instead of urea
bonded in column No. 7 :Fully Panelled Item 8.12
P.Sqm 28.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 20.00
8.14.2 One side teak face particle board in column No. 7. Fully Panelled
Item 8.12
P.Sqm 184.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 92.00
8.14.3 Both side teak face particle board in column No.7 :Fully Panelled
Item 8.12
P.Sqm 260.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 130.00
8.14.4 One side laminated face particle board in column No. 7 :Fully
Panelled Item 8.12
P.Sqm 187.00
8.14.5 Both side laminated face particle board in column No. 7:Fully
Panelled Item 8.12
P.Sqm 285.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 131.00
8.14.6 Using medium density fibre board instead of particle board in
column No. 7:
(a) Interior grade.
Fully Panelled Item 8.12
P.Sqm 148.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 74.00
(b) Exterior grade.
Fully Panelled Item 8.12
P.Sqm 231.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 116.00
8.14.7 Using medium density fibre board one side laminated face instead
of particle board in column No. 7 :
(a) Interior grade.
Fully Panelled Item 8.12
P.Sqm 190.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 95.00
(b) Exterior grade.
Fully Panelled Item 8.12
P.Sqm 238.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 119.00
8.14.8 Using medium density fibre board both side laminated face instead
of particle board in column No. 7 :
(a) Interior grade.
Fully Panelled Item 8.12
P.Sqm 226.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 113.00
(b) Exterior grade.
Fully Panelled Item 8.12
P.Sqm 278.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 139.00
8.14.9 Using thicker panels than 12mm in column No. 7 for window of
thickness 40mm & above. (a) 15mm thick M.D.F. Board
(i) Interior grade.
Fully Panelled Item 8.12
P.Sqm 208.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 104.00
(ii) Exterior grade.
Fully Panelled Item 8.12
P.Sqm 276.00
Partly Panelled & Partly Glazed Item No. 8.13
P.Sqm 138.00
8.15.2 Using pin head glass instead of 4mm thick plain glass in column
No.12
8.18.2 30 mm thick .
Commercial Veneer both side P.Sqm 1601.00
Decorative teak veneer One side P.Sqm 2001.00
Decorative teak veneer both side P.Sqm 2401.00
8.18.3 35 mm thick .
Commercial Veneer both side P.Sqm 1712.00
Decorative teak veneer One side P.Sqm 2146.00
Decorative teak veneer both side P.Sqm 2579.00
8.18.4 40 mm thick .
Commercial Veneer both side P.Sqm 1768.00
Decorative teak veneer One side P.Sqm 2218.00
Decorative teak veneer both side P.Sqm 2668.00
8.19.4 For Internal teak wood lipping in 25mm depth P.Sqm 215.00
8.19.5 Extra in flush doors for providing vision panel of size 15x15 cm
square of 15cm dia
Each 131.00
8.19.6 Extra if louvers (not exceeding 0.2 sqm) are provided in flush door
shutters (overall area of door shutters to be measured) Decorative
type door.
P.Sqm 306.00
8.19.7 Extra for cutting rebate in flush door shutters (Total area of the
shutter to be measured)
P.Sqm 92.00
8.19.8 Add extra for Sunmica 0.8mm thick.
P.Sqm 410.00
8.2 type (hollow core construction ) with internal frame of 1st grade
wood having styles and top rails of 100 mm width & bottom and
lock rails of 150 mm width with 3 Nos. cross battens of 50mm thick
and 1 nos. 50 mm vertical middle member thoughtout length us
8.21 Add extra over item No. 8.20 for Double leaf shutters. P.Sqm
8.22 Add extra for providing 4 mm thick teak veneer ply instead of 4mm
thick commercial ply over item No. 8.20.
P.Sqm 317.00
8.23 Add extra for providing vision panel not exceeding 1 Sqm
rectangular or circular.
Each 57.00
PELMETS
8.24 Providing and fixing 12 mm thick pelmets with 20mm dia C.P. steel
curtain rod and brackets 100x25x3mm M.S. flat etc. complete :
8.25 Add extra over item No. 8.24 providing 12 mm thick top horizontal
cover of respective wood on pelmets :
CURTAIN RODS
8.26 Providing and fixing Anodised Aluminium Curtain rod with
Aluminium brackets complete :
8.27 Providing and fixing Aluminium curtian rails with rollers stop ends
rails and brackets in pelmets.
P.Rmt 177.00
8.28 Providing and fixing 20 mm dia Conduit pipe curtain rods with steel
brackets etc. complete.
P.Rmt 25.00
8.29 Providing and Fixing 38 mm thick wood panelled wall having 75
mm wide wood frame having door opening provision maximum
pan el. area 0.4 Sqm with steel fitting & antitermite treatment
complete as per drawing with panels of :
P.Sqm 2392.00
8.30.2 4 mm thick teak ply on both sides.
P.Sqm 2659.00
8.30.3 4 mm thick fibre cement flexo board (A.C. sheet ) on both sides.
P.Sqm 1887.00
8.30.4 6 mm thick fibre Board on both sides.
P.Sqm 2444.00
8.30.5 0.8 mm mica of approved make on ply with addesive complete.
P.Sqm 792.00
SHELVES
8.31 Providing and fixing flat pressed 3 layer particle board in shelves
with screws and wooden brackets:
8.31.1 12 mm thick P.Sqm 410.00
8.31.2 19 mm thick P.Sqm 550.00
8.31.3 25 mm thick P.Sqm 610.00
8.33 Providing and fixing wall panelling using soft wood frame of size
50x25mm @600 mm c/c in both directions duly treated with anti-
termite treatment making grooves painting of grooves specification
and drawing using :
P.Sqm 2090.00
8.33.5 12 mm thick one side laminated board Practical board (Phenol
bonded)
P.Sqm 2254.00
8.33.6 12mm thick Acoustical Board with 50mm thick glass wood and
glass fibremat.
P.Sqm 1837.00
8.33.7 Providing and fixing 50 mm thick resin bounded glass whool 32
kg/cum density wrapped in julities cloth bag (box type) and held in
position using chicken mesh.
P.Sqm 360.00
8.33.8 Providing and fixing Hassian cloth of approved colour and texture
over soft wood frame glass wool & fibre glass tissuse paper.
P.Sqm 175.00
MISCELLANEOUS WOOD WORK
8.34 Providing and fixing Nigeria / Ghana Teak wood grade-I mouldings
and beadings in droos and windows size :-
8.39 Providing and fixing channel pipe and rollers for making
arrangement of sliding of doors complete in all respects.
P.Rmt. 650.00
8.4 Providing brackets fixed in 7 .5x7 .5x15 cm blocks of cement
concrete 1 :3:6 (1 cement: 3 coarse sand :6 graded stone
aggregate 20 mm nominal size) to support 20 cm wide shelves.
8.43 Providing and fixing ghana teak wood plain lining tongued and
grooved on and including wooden plugs complete with necessary
screws and priming coat on unexposed surface.
8.43.1 40 mm thick P.Sqm 3333.00
8.43.2 25mm thick P.Sqm 2209.00
8.44 Providing and fixing 20 mm thick plain lining tongued and grooved
on and including wooden plugs complete with necessary screws
.and priming coat on unexposed surface with.
P.Sqm 1237.00
8.46 Providing and fixing 4 mm thick plywood plain lining with
necessary screws, priming coat on unexposed surface etc.
complete with teak ply facing of approved manufacture.
P.Sqm 1210.00
8.47 Providing and fixing 40mm thick ghana teak wood plain panelling
with skirting chair rails, and cornice with necessary , screws,
priming coat on unexposed surface etc. complete.
P.Sqm 4061.00
8.48 Providing and fixing skirting of prelaminated with (one side
decorative and other side balancing lamination) flat pressed, 3
layer (like Novapan, Ecoboard, etc.,) or graded particle board (like
Bhutan Board) (medium density) Grade I, Type II, IS :12823 ma
P.Rmt. 42.00
8.5 Providing and fixing curtain rods of 1.25 mm thick chromium plated
brass plate, with two chromium plated brass brackets fixed with
C.P. brass screws and wooden plugs, etc., wherever necessary
complete:
8.51 Providing and fixing nickel plated M.S. pipe curtain rods with nickel
plated brackets
8.53 Providing & Fixing of ward robe shutters made out of 19mm thick Sqm 7221.00
BWP block board ISI of superior quality make. Front side finishing
with 4mm thick teak veneer approved make and 0.8mm thick
approved shade mica in the inner side. Covering with teak wood
bea
8.54 Providing and Fixing Bamboo Zafari/Fencing consisting of superior Sqm 2615.00
quality 25mm dia Solid Bamboo placed vertically & fixed together
with 3 Nos Horizontal running members of wood in scantling of
section size 50x40mm and fixed with nut and bolt to existing
8.55 Providing & Fixing mica of approved make for inner/outer side of
shutters with fevicol & nails complete as per approved by
engineer in charge.
8.57 Providing and fixing S.S. Rod 30mm dia (304 grade ,16SWG) Rmt 1034.00
including brackets fixed with C.P. brass screws and rawl plugs,
etc., wherever necessary complete two side central all fittings.
1001723.66
OR
Providing and fixing stone slabs table rubbed, 18 mm thick in
Walls, Steps, Pillars, Counters, Jambs, Shelves, Sills etc. laid on
12mm (Av.) thick base of CM 1:3 (1 cement : 3 coarse sand)
jointing with white cement mortar 1:2 (1white cement : 2 marble du
WHITE MARBLE
7.1.1 Makrana second quality plain.
Upto 800 Cm2 Tiles
P.Sqm 1453.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1701.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 2135.00
Above 3601 Cm2 Slabs
P.Sqm 3127.00
7.1.2 Makrana Superior quality having light spots.
Upto 800 Cm2 Tiles
P.Sqm 1313.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1650.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 2024.00
Above 3601 Cm2 Slabs
P.Sqm 2323.00
7.1.10 Banswara.
Upto 800 Cm2 Tiles
P.Sqm 1006.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1197.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 1425.00
Above 3601 Cm2 Slabs
P.Sqm 1887.00
7.1.13 Bundi.
Upto 800 Cm2 Tiles
P.Sqm 1024.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1197.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 1275.00
Above 3601 Cm2 Slabs
P.Sqm 1608.00
GREEN MARBLE
7.1.15 Abu.
Upto 800 Cm2 Tiles
P.Sqm 1197.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1455.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 1608.00
Above 3601 Cm2 Slabs
P.Sqm 2098.00
7.1.16 Bhaislana,Abu,Kishangarh Zebra.
Upto 800 Cm2 Tiles
P.Sqm 1111.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1237.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 1350.00
Above 3601 Cm2 Slabs
P.Sqm 1608.00
GREY MARBLE
7.1.17 Bundi.
Upto 800 Cm2 Tiles
P.Sqm 1111.00
801 Cm2 to 1500 Cm2 Tiles
P.Sqm 1197.00
1501 Cm2 to 3600 Cm2 Tiles
P.Sqm 1350.00
Above 3601 Cm2 Slabs
P.Sqm 1608.00
NOTE:
1- Add extra for doing mirror polishing.
3- Add extra in Marble flooring work for upto 50mm wide strip
of Green/ White/ Jaisalmer Stone in flooring work as per
direction of Engineer Incharge.
7.2 Providing and fixing Granite stone slab mirror polished and
machine edge cut in walls, pillars, steps, Shelves, Sills Counters,
Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1
cement : 3 coarse sand) jointing with white cement mortar 1:2
7.3 Providing and fixing 1st quality standard white, grey, ivory, fume
red brown, light green, light blue and other light shades glazed
tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm
in walls, floors, steps, pillars etc. laid on a bed of nea
P.Sqm 693.00
7.3.3 Add extra over item no. 7.3.1 and 7.3.2 for Marble printed, granite
shade tiles.
0.15
7.3.4 Add extra over 7.3.1 and 7.3.2 for using coloured dark shade tiles
instead of White / Ivory / Light Grey/ Light Green/ Sky Blue/ Light
Brown and other light shade coloures.
P.Sqm 85.00
7.4 Providing and fixing 75 mm widen Decorative Border in different
shades and in all coloures for glazed tiles
P.Rmt. 300.00
7.5 Providing and fixing Motive pieces all coloures for glazed tiles.
P.Sqm 790.00
P.Sqm 1149.00
Note :
Deduct over item no. 7.7 for using any other make 0.10
7.8 Providing and fixing marble mirror polished 7mm thick tiles of
approved make and size in walls, floors, steps, pillars etc. laid on a
bed of neat cement slurry including nicely finished joints using
water proof joint filler powder and finished with flush
7.9.1 25 x 6 mm x 30 cm long.
Each 165.00
7.9.2 15 x 6 mm x 16.5 cm long.
Each 63.00
7.1 Providing and fixing copper pipe 7.5cm long of 6mm external
diameter in cement sand 1:3 (1 cement :3 fine sand) including
making necessary chases.
Each 32.00
7.11 Providing and fixing stone dowel 10x5x2.5cm cut to double wedge
shape as per design in cement sand mortar 1:3 (1 cement : 3 fine
sand) including making necessary chases.
Each 10.00
7.12 Extra for providing edge moulding to 18mm thick marble stone
counters, vantities etc. over item No. 7.1 & 7.2 including machine
polishing to edge to give high gloss finish etc. complete as per
design approved by Engineer - in - Charge.
Each 61.00
Opening
7.14 Providing non slip grooves to granite/ kota stone flooring, counters, Mtr. 95.00
vanities etc. using groove cutter V type including machine
polishing to groove to give high gloss finish etc. complete as per
design approved by engineer in charge
7.15 P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor,
skirting and steps etc.in different sizes (thickness minimum 10mm)
with water absortion less than or equal 0.08% and conforming to
IS 15622 of approved make in all colour and shade, la
7.16 P & F 1st quality Heavy Duty Vitrified glazed MAT tiles on floor,
skirting and steps etc.in different sizes (thickness minimum 10mm)
with water absortion less than or equal 0.08% and conforming to
IS 15622 of approved make in all colour and shade, laid wi
7.17 P & F 1st quality Heavy Duty Vitrified Double Charged tiles on
floor, skirting and steps etc.in different sizes (thickness minimum
10mm) with water absortion less than or equal 0.08% and
conforming to IS 15622 of approved make in all colour and shade,
lai
2- In case of non-availability of stone header of proper size cement concrete header of mix
1:3 : 6 (M-100) with 25mm graded stone aggregate with smooth finish may be provided by
the contractor at no extra cost.
3- The Concrete for all grade shall be produced in conformation to the laid down procedures
and all relevant clauses of IS 456 : 2000
CHAPTER B-6
Chapter Code No.
Description Unit
STONE MASONRY
6.1 Random Rubble stone masonry for foundation and plinth in Cement
Sand mortar above 30CM thick wall in:
6.1.1 Mud Mortar.
P.Cum
6.1.2 Dry Masonry.
P.Cum
6.1.3 Lime Sand Mortar 1:3 ( 1-Lime Putty : 3-Sand).
P.Cum
6.1.4 Cement Mortar 1:3 ( 1-Cement : 3-Sand).
P.Cum
6.1.6 Cement Mortar 1:5 ( 1-Cement : 5-Sand).
P.Cum
6.1.7 Cement Mortar 1:6 ( 1-Cement : 6-Sand).
P.Cum
6.2 Random Rubble stone masonry for superstructure above plinth level
one storey height above 30cm. thick walls in :
6.2.1 Mud Mortar.
P.Cum
6.2.2 Dry Masonry.
P.Cum
6.2.3 Lime Sand Mortar 1:3 ( 1-Lime Putty : 3-Sand).
P.Cum
6.2.4 Cement Mortar 1:3 ( 1-Cement : 3-Sand).
P.Cum
6.2.5 Cement Mortar 1:4 ( 1-Cement : 4-Sand).
P.Cum
6.2.6 Cement Mortar 1:5 ( 1-Cement : 5-Sand).
P.Cum
6.2.7 Cement Mortar 1:6 ( 1-Cement : 6-Sand).
P.Cum
6.2.8 Cement Mortar 1:8 ( 1-Cement : 8-Sand).
P.Cum
6.3 Extra over item No.6.1 & 6.2 for :
6.5.1 Red Karauli sand stone rough dressed 25 to 35mm thick. P.Cum
6.5.2 Extra over item No. 6.5.1 for fine grinded stone used instead of rough
drssed.
P.Sqm
6.5.3 White Dholpur sand stone rough dressed 25 to 35mm thick.
P.Cum
6.5.4 Extra item No. 6.5.3 for fine grinded stone used instead of rough
dressed.
P.Sqm
6.5.5 Modak or similar stone rough dressed 30 to 40mm thick.
P.Sqm
6.5.6 Extra for fine grinded stone used instead of rough dressed.
P.Sqm
6.5.7 Marble facing abardari (white and pink) polished, 18 to 25mm thick.
P.Cum
P.Cum
6.6 Providing stone veneer facing in strips upto 125mm width and upto
20mm thick in cement mortar 1:4 including ement pointing 1:2 with
and admixture of pigment matching the stone shade upto 4.5Mtr.
Height above plinth level, in :
6.13 Supplying and fixing in cement sand mortar 1:4 sand or other
approved stone dasa or coping of thickness 75 to 100mm (fine
dressed) :
6.14.1 50 mm thick.
P.Sqm
6.14.2 75 mm thick.
P.Sqm
6.14.3 100 mm thick.
P.Sqm
6.15 Supplying and fixing dressed sand or other approved stone shelves,
tands in cement mortar 1:3 with fine dressed edges :
6.15.1 25mm thick.
P.Sqm
6.15.2 35mm thick.
P.Sqm
6.15.3 50mm thick.
P.Sqm
6.15.4 75mm thick.
P.Sqm
6.16 Supplying and fixing in walls machine cut and polished stone
shelves, tands and sills in CM 1:3 with machine cut edges :
6.16.1 Sand or other approved stone 25mm thick.
P.Sqm
6.16.2 Sand or other approved stone 35mm thick.
P.Sqm
6.16.3 Sand or other approved stone 50mm thick.
P.Sqm
6.16.4 Kota stone 25 to 30mm thick.
6.19 Deduct from item No. 6.18.1 for fixing done in lime sand mortar 1:2
instead of CM 1:3.
P.Sqm
6.2 Providing dab stone over Chajjas duly fixed in cement sand mortar
1:6 complete :
P. Rmt.
Note :- Recover cost of useful stone @ 2/3rd of masonry work
dismantalled quantity.
P.Cum
PART - B : ASHLAR WORK
6.40.1 60 x 26 x 18 cm.
Red Ashler Each
Soorsagar or eqvt. White Ashler
6.40.2 60 x 30 x 25 cm.
Red Ashler Each
Soorsagar or eqvt. White Ashler
6.41 Supplying and fixing ashlar stone chhajja 5 to 7 cm. thick all exposed
surface fully fine dressed, weather dripped including 75x75mm.
cement botta (1:2 : 4) between chhajja & wall (single piece upto 1:2m
length) :
6.41.1 Three line dressed.
Red Ashler P.Sqm
Soorsagar or eqvt. White Ashler
6.41.2 Two line dressed
Red Ashler P.Sqm
Soorsagar or eqvt. White Ashler
6.41.3 One line dressed.
Red Ashler P.Sqm
Soorsagar or eqvt. White Ashler
6.42 Supplying and fixing Red ashlar railing ordinary with takia and
thambli complete fine dressed :
6.42.1 Three line dressed.
Red Ashler P.Sqm
6.42.2 Two line dressed
Red Ashler P.Sqm
6.43 Supplying and fixing Red ashlar stone jali 5 to 7 cm. thick curved :
6.55 Providing & fixing "ornamental stone cladding" of approved sand P.Sqm
stone with dressing complete as per existing design/pattern/approved
design,fixing with 30mm thickgrinded cement mortar 1:2 & pointing
with white cement with araldite and pigment to match sha
6.56 Providing and fixing fine dressed sand stone "Dasa/coping" as per P.Sqm
existing matching , fixing in grinded lime surkhi mortar 1:2 including
pointing in cream and stone powder 1:1 with an admixture of pigment
to match the shade of stone complete in all respec
6.57 Providing and fixing stone "Pillars" (Stambha) on pillers of Sabha P.Cum
Mandap/ Antral/ Praeshmandapa etc.fine dressed as per existing
matching stone/ approved quarry with plain moulding work as per
temple architecture complete with all scaffolding and shutte
6.58 Providing and fixing of fine dressed "Valted decorative ceiling" of P.Sqm
Sabha mandapa/ Antral/ Praeshmandapa etc. having simple carving
work / moulding work of matching/ approved stone fixing carefully by
machenical/manual system carefully with proper order a
6.59 Providing and fixing "Stone Kalasha" as per existing matching on Each
doms od chattries/jharokhas as per existing design & dimensions as
per traditional practices, fixing of kalash carefully without damaging
the doms complete in all respect. Sand stone/appro
6.6 Providing and fixing stone " Lintels " of Sabha Mandap/ Antral/ P.Cum
Praeshmandapaas etc.fine dressed as per existing matching stone/
approved quarry with plain moulding work as per temple architecture
complete with all scaffolding and shuttering work, lead an
Rate
1663.00
1269.00
2037.00
3030.00
2698.00
2577.00
2123.00
1983.00
2749.00
3468.00
3278.00
3137.00
3018.00
2887.00
252.00
122.00
194.00
200.00
115.00
155.00
311.00
270.00
304.00
159.00
150.00
80.00
84.00
1141.00
85.00
1685.00
85.00
1339.00
85.00
1541.00
1676.00
1137.00
85.00
4251.00
4384.00
5393.00
5630.00
6309.00
6525.00
6095.00
649.00
436.00
543.00
908.00
961.00
941.00
941.00
3575.00
3745.00
4623.00
5342.00
1722.00
2418.00
2418.00
1059.00
1124.00
1300.00
1617.00
1357.00
1357.00
1357.00
708.00
646.00
70.00
8431.00
7801.00
488.00
591.00
60.00
980.00
982.00
882.00
924.00
3295.00
61.00
16.00
93.00
13.22
600.00
8835.00
11582.00
8880.00
11627.00
8925.00
11672.00
8937.00
11684.00
0.00
0.00
0.00
0.00
10090.00
12616.00
10230.00
12796.00
10315.00
12881.00
10454.00
13021.00
12926.00
16415.00
11139.00
14600.00
2601.00
3772.00
2542.00
3398.00
2790.00
3826.00
8099.00
374.00
762.00
291.00
473.00
70.00
94.00
42391.00
42826.00
39976.00
40411.00
21196.00
21413.00
19988.00
20206.00
311.00
485.00
447.00
625.00
1141.00
1611.00
1014.00
1035.00
815.00
902.00
1060.00
913.00
744.00
1740.00
2214.00
338.00
379.00
72.00
92.00
273.00
489.00
499.00
491.00
672.00
100.00
207.00
317.00
1580.00
23.00
3424.00
2988.00
34785.00
32773.00
2724.00
30038.00
BRICK WORK
5.1 Brick masonry in foundation and plinth with bricks of class
designation 75 in :
P.Cum 262.00
5.3.1.2 Upto 45 cm length and two corners are free
P.Cum 110.00
5.3.1.3 Upto 90 cm length and all sides are free
P.Cum 157.00
5.3.2 Circular Pillars.
P.Cum 157.00
5.3.3 Circular masonry in plan upto a mean radius not exceeding 6
Mtr.
P.Cum 150.00
5.4 Extra for cutting or chamfering of bricks upto one brick depth to
required shape in masonry work.
P.Cum 9.00
5.5 Brick work in plain arches in super structure upto third storey in
cement mortar 1 : 3 including centering and shuttering complete
span upto 6 Mtr. with Brick of class designation 75.
P.Cum 4884.00
5.6 Brick work in gauged arches in super structure upto third storey
in cement mortar 1 : 3 including centering and shuttering
complete span upto 6 meter with Brick of class designation 75.
P.Cum 4843.00
5.7 Add extra over item No. 5.5 & 5.6 for arches exceeding 6m
span including all shuttering and centering, bolting wedging and
removal.
P.Cum 120.00
P.Sqm 28.00
5.1 Brick work in partition in super structure upto third storey 7cm.
thick (brick on edges) using bricks of class designation 75 in :
5.19 Add extra for doing brick work for each subsequent storey for
respective items beyond third story.
5.21 Add extra over item of brick work with class designation 100 in
substitution of class designation 75 :
NEW ITMES
5.22 Brick work with clay flyash F.P.S. brick (IS 13757- 1993 ) of
class designation 75 in superstructure above plinth level upto
floor five level in :
5.22.1 Cement mortar 1 : 4 (1 cement : 4 coarse sand) Cum 4843.00
5.22.2 Cement mortar 1 : 6 (1 cement : 6 coarse sand) Cum 4627.00
5.24 Add extra for brick work in superstructure above floor five level,
for each four floors or part thereof.
5.24.1 Quantity in Cum. Cum. 236.00
5.24.2 Quantity in Sqm. Sqm. 21.00
5.25 Add extra over item of brick work with class designation 100 in
substitution of class designation 75 :
5.25.1 Quantity in Cum. Cum. 148.00
5.25.2 Quantity in Sqm. Sqm. 17.00
5.26 Half Brick work with mechanised autoclaved flyash lime bricks
conforming to IS: 12894 :2002 of class designation 100 in
superstructure above plinth level upto floor V level in.
5.26.1 Cement mortar 1 : 4 (1 cement : 4 coarse sand) Sqm 591.00
5.26.2 Cement mortar 1 : 6 (1 cement : 6 coarse sand) Sqm 567.00
5.27 Half Brick work with mechanised autoclaved flyash lime bricks
conforming to IS: 12894 :2002 of class designation 75 in
superstructure above plinth level upto floor V level in.
5.27.1 Cement mortar 1 : 4 (1 cement : 4 coarse sand) Sqm 573.00
5.27.2 Cement mortar 1 : 6 (1 cement : 6 coarse sand) Sqm 549.00
CAST-IN-SITU CONCRETE:
4.1 Providing and laying in position specified grade of cement
concrete for all RCC structural elements upto plinth level
including curing, compaction, finishing with rendering in cement
sand mortar 1:3 (1 cement: 3 coarse sand) and making good
the joints exc
5.00%
SHUTTERING
4.6 Centering and Shuttering with plywood or steel sheets
including strutting, propping bracing both ways and removal of
formwork for foundation in basements rafts, footings, straps
beams, bases of columns etc. up to plinth level.
P.Sqm 143.00
P.Sqm 270.00
4.7.12 Add extra for shuttering in circular work in plan up to dia 10m
over item Nos. 4.7.1 to 4.7.2
P.Sqm 36.00
4.7.13 Add extra for shuttering in circular work in plan, above 10 mtr.
and up to 30 Mtr. Dia over item no. 4.7.1 and 4.7.2
P.Sqm 24.00
4.8 Add extra over item no 4.7.1 to 4.7.11for using steel telescopic
prop instead of wooden member
P.Sqm 20.94%
4.9 Add extra over item no 4.7.1 to 4.7.11for using steel cup lock
system instead of wooden member
P.Sqm 53.00
4.1 Add extra over item Nos. 4.7.1 to 4.7.11 for doing centering
and shuttering work for each subsequent storey above three
floor.
P.Sqm 25.00
4.11 Add extra over item no. 4.7.1 to 4.7.11 for every additional 1 m
ht or part there off beyond 4.5mtr single story height of
shuttering.
P.Sqm 34.00
STEEL REINFORCEMENT:
4.12 Providing and fabricating reinforcement for R.C.C. work
including straightening, cutting, bending, placing in position and
binding (including cost of binding wire) all complete up to floor
three level.
4.12.1 Mild steel and medium tensile bars (IS : 432).
Kg. 66.00
4.12.2 Cold twisted deformed bars (IS : 1786).
Kg. 67.00
4.12.3 Hot rolled deformed bars (IS : 1139).
Kg. 67.00
4.12.4 Thermo-mechanically Treated bars (Conforming of relevent IS
code)
Kg. 67.00
4.13 Labour charges for cutting, bending for fabrication and binding
reinforcement (plain or tor/ribbed steel) as per drawing and
design for R.C.C. and R.B. work including cost of binding wire
with all lead and lift up to floor three level complete.
Kg. 6.50
4.14 Add extra over item No. 4.12 and 4.13 in superstructure above
floor three level for subsequent floor level or part there of.
Kg. 0.52
PRECAST CEMENT CONCRETE
P.Cum 10863.00
4.15.6 Cement concrete jali reinforced with 1.6 mm dia Mild steel wire
complete as per approved design excluding plastering of
jambs, sills and soffits
4.15.6.1 75mm thick
P.Sqm 643.00
4.15.6.2 50mm thick
P.Sqm 587.00
4.15.6.3 40 mm thick
P.Sqm 500.00
4.15.6.4 30mm thick
P.Sqm 462.00
4.16 Add extra over item no.4.15.6 for both side jali
P.Sqm 0.40
4.17 Supplying and fixing Precast R.C.C. door and window frames
up to floor three level nicely finished in M-20 Nominal Mix with
1% steel, single or double rebated as required, of size:
4.17.1 100 mm x 75 mm
P.Mtr. 127.00
4.17.2 125mm x 75mm
P.Mtr. 153.00
4.18 Add extra over item Nos. 4.15 to 4.17 in superstructure above
floor three level for subsequent floor level or part there of.
0.02
4.19 Providing and fixing precast R.C.C. slab in M15 Nominal Mix as
per design up to 30 mm thick for shelves etc. including cost of
reinforcement consisting of wire mesh 100x100x4mm with fine
finish.
P.Sqm 417.00
4.2 Add extra over item No. 4.19 for mosaic finish on one to three
edges and top surface of shelves with marble chipping (1 mm
to 4mm nominal size) in grey cement duly finished and
polished.
P.Sqm 95.00
ENCASING ROLLED STEEL STECTION
4.21 Encasing rolled steel section in beams and columns, with M20
Nominal Mix cement concrete including centering and
shuttering complete but excluding cost of reinforcement.
P.Cum 6729.00
4.22 Encasing rolled steel section in grillages with M20 Nominal Mix
including centering and shuttering complete but excluding cost
of expanded metal and hangers.
P.Cum 5075.00
4.23 Providing and fixing expanded metal mesh of size 20x 60 mm
and strands 3.5 mm vide 1.6 mm thick weighing 3.64 Kg per
sqm. for encasing of rolled steel sections in beams, columns
and grillages excluding cost of hangers.
P.Sqm 261.00
MISCELLANEOUS
4.24 Providing and fixing in position copper plate as per design for
expansion joints.
Kg. 905.00
4.25 Providing and fixing in position Aluminum plate as per design
for expansion joints.
Kg. 498.00
4.26 Providing and filling in position bitumen sealing compound
grade A (IS 1834 ) in expansion joints.
P. Cm. depth
P. Cm. width
652.00
for 100 mtr.
Length
4.27 Providing and filling in position bitumen mix filler of proportion
80 Kg. of hot bitumen, 1 Kg. of cement and 0.25 cubic meter of
coarse sand for expansion joints.
P. Cm. depth
P. Cm. width
164.00
for 100 mtr.
Length
4.28 Providing and fixing in position bitumen impregnated fiberboard
confirming to IS: 1838-1961 in expansion joints including the
cost of primer sealing compound.
4.28.1 12 mm. thick
P.Sqm 766.00
4.28.2 18 mm. thick
P.Sqm 988.00
4.28.3 25 mm. thick
P.Sqm 1321.00
4.29 Providing and fixing Asbestos sheet 6mm thick and 150mm.
Wide over expansion joint with fixing rowl plug and screws as
per designs to match the colour shade of the distemper or wall
treatment.
P.Rmt 713.00
4.3 Providing and fixing Aluminum sheet 2.0 mm thick and 150mm.
Wide over expansion joint with fixing rowl plug and aluminum
screws as per designs to match the colour shade of the
distemper or wall treatment.
P.Rmt 1863.00
4.31 Add extra for laying R.C.C. in or under water and or liquid mud
including the cost of pumping or bailing out water and removing
slush etc. complete.
P.Cum Per
44.00
Mtr. Depth.
4.32 Providing and fixing expansion joint board for building RCC
column beams, walls, slab of Polyethylene foam of density 30
to 35 Kg/m3 of Armour Board.
4.32.1 12 mm Thick
P.Sqm 468.00
432.2 20mm Thick
P.Sqm 523.00
4.32.3 25 mm Thick
P.Sqm 633.00
4.32.4 30 mm Thick
P.Sqm 704.00
4.32.5 40 mm Thick
P.Sqm 880.00
4.34.1 To vertical joint between RCC columns, bricks & stone masonry
in size 40 mm width and 12 mm depth, including providing back
up material (Thermocoal foam) if required.
P. Mtr. 600.00
4.34.2 To joints in flooring, as per drawing with first layer of poly
sulphide sealant in size 20 mm width and 10 mm depth over
PE Foam and then providing polyethylene foam back up rod 25
mm dia size and finally providing another layer of poly sulphide
sealant i
P. Mtr. 500.00
4.34.3 To horizontal joints between beams masonry in size 40 mm
width and 20 mm depth on top faces with pouring grade
providing required back-up material (Thermocoal foam/ PE
foam) complete.
P. Mtr. 825.00
4.35 Welding of M.S. rounds plain/TOR for R.C.C. work, joints are to
be butt or V-shaped, confirming to I.S. standards, complete in
all respect at work site:
P.Cum 5500.00
4.37 Add extra over item no. 4.36 for vacuum processed concrete
including cost of equipments labour etc.
P.Sqm 50.00
4.38 Cutting of construction joint/ longitudinal joint 4 to 6 mm. wide &
75 to 100 mm deep using mechanical concrete cutter including
cost of diamond bit cutting wheel and filling of bitumen sealing
compound in groove including cost of sealing compound.
P. Mtr. 65.00
Cum 5614.00
4.4 Add extra for providing richer mixes respectively at all floor
levels
4.40.1 Providing M-25 grade concrete by using min 410 kg of cement
Cum 63.00
per cum instead of M-20 grade design mix.
4.40.2 Providing M-30 grade concrete by using min 420 kg of cement
Cum 126.00
per cum instead of M-20 grade design mix.
4.40.3 Providing M-35 grade concrete by using min. 428 kg of cement
Cum 176.00
per cum instead of M-20 grade design mix.
4.40.4 Providing M- 40 grade concrete by using min. 435 kg of cement
Cum 220.00
per cum instead of M-20 grade design mix.
4.40.5 Add extra for RCC work in superstructure above floor five level
Cum 98.00
for each four floor or part thereof .
4.40.6 Deduct for using less cement quantity than the quantity as
provided in the item of design mix concrete/RMC as arrived as Kg 6.00
per mix design.(on cement quantity)
3.2.3 M15 grade Nominal Mix (with graded stone aggregate 20mm
nominal size).
P.Cum 4037.00
3.2.4 M10 grade Nominal Mix (with graded stone aggregate 20mm
nominal size).
P.Cum 3407.00
3.4.1 Add Extra for laying concrete in superstructure upto floor three
level in item no. 3.2
P.Cum 115.00
3.5 Deduct if brick aggregate is used in substitution stone aggregate
in item No. 3.2.5 to 3.2.8 & 3.3.5 to 3.3.6.
P.Cum 96.00
3.6 Extra for laying in floor consolidation extra labour required for slow
per gress.
P.Cum 92.00
3.13 Providing and mixing admixure in Concrete Flooring/Cement per 100 55.00
Plaster/Cement Comcrete Road, Plain or RCC work & water gram
retaining works providing and mixing admixture of Synthetic pack
Nylon-6 Fibres or polycaprolactam free from any reprocess
Olefins & confirming to
P.Cum 2038.00
2.7 Lime surkhi sand mortar 1 : 1: 1 ( 1 Lime putty : 1 surkhi : 1 sand )
P.Cum 2711.00
P.Cum 3146.00
2.19 White cement marble powder mortar 1 :2 (1 white cement : 2
marble powder)
P.Cum 13265.00
COMPOSITE MORTAR :
2.23 Cement lime sand mortar 1 : 1 : 4 ( 1 cement : 1 lime putty : 4
sand).
P.Cum 3743.00
P.Sqm 28.00
1.2 Earth work in rough excavation, banking excavated earth in
layers not exceeding 20cm in depth, breaking clods
watering, rolling each layer with 1/2 tonne roller, or stone or
steel rammers and rolling every 3rd and top- most layer with
power roller of mini
P. Cum 217.00
P. Cum 138.00
1.4 Deduct in item No. 1.2 & 1.3 for not rolling with power roller
of 8 to 10 tonne capacity for banking excavated earth in
layers not exceeding 20 cm in depth.
P. Cum 2.00
1.5 Deduct in item No. 1.2 & 1.3 for not watering the excavated
earth for banking.
P. Cum 23.00
1.6 Earth work in excavation over areas (exceeding 30cm in
depth, 1.5 Mtr. in width as well as 10 Sqm on plan) including
disposal of excavated earth lead up to 50m and with all lift
disposed earth to be levelled and neatly dressed: All kinds of
soil
P. Cum 191.00
1.7 Earth work in excavation over areas (exceeding 30cm in
depth, 1.5 Mtr. in width as well as 10 Sqm on plan) including
disposal of excavated earth lead up to 50m and lift up to 1.5
Mtr. disposed earth to be levelled and neatly dressed
including stacking of
P. Cum 196.00
1.9 Earth work in excavation in foundation trenches or drains
including dressing of sides and ramming of bottoms, lift up
to 1.5 Mtr. including taking out the excavated soil and
depositing and refilling of jhiri with watering & ramming and
disposal of surplus
1.13.1.2 Pipes cables, etc. exceeding 80mm dia but not exceeding
300mm dia.
P.Mtr. 200.00
1.13.1.3 Pipes, cables etc. exceeding 300mm dia but not exceeding
600mm dia.
P.Mtr. 314.00
1.14 Add extra in item No. 1.13 for excavating trench for pipes,
cables etc. in all kinds of soil for depth exceeding 1.5 Mtr.
but not exceeding 3 Mtr.
1.30
1.15 Add extra in item No. 1.13 for excavating trench for pipes,
cables etc. in all kinds of soil for depth exceeding 3 Mtr. But
not exceeding 4.5 Mtr.
1.72
1.16 Excavating trenches of required width for pipes cables etc.
including excavation for sockets, depth up to 1.5 Mtr.
including taking out the excavated materials, refilling the soil
as required in layers not exceeding 20cm in depth including
consolidating e
P.Mtr. 261.00
1.16.2.2 Pipes cables, etc. exceeding 80mm dia but not exceeding
300mm dia.
P.Mtr. 645.00
1.16.2.3 Pipes, cables etc. exceeding 300mm dia but not exceeding
600mm dia.
P.Mtr. 743.00
1.16.3 HARD ROCK (BLASTING PROHIBITED) USEFUL
MATERIAL 30% OF VOLUME EXCAVATED
1.16.3.1 Pipes cables etc. not exceeding 80mm dia
P.Mtr. 354.00
1.16.3.2 Pipes cables, etc. exceeding 80mm dia but not exceeding
300mm dia.
P.Mtr. 877.00
1.16.3.3 Pipes, cables etc. exceeding 300mm dia but not exceeding
600mm dia.
P.Mtr. 1009.00
1.17 Add extra over item No. 1.16 for excavating trenches for
pipes cables etc. in ordinary/hard rock exceeding 1.5 Mtr. In
depth but not exceeding 3 Mtr.
P.Mtr. 1.02
1.18 Add extra over item No. 1.16 for excavating trenches for
pipes cables etc. in ordinary/hard rock exceeding 3 Mtr. In
depth but not exceeding 4.5 Mtr.
P.Mtr. 2.53
1.19 P & F Close timbering in trenches including strutting, shoring
and packing cavities (wherever required) etc. Complete
(Measurement to be taken of the face area timbered):
1.29.1 5 to 9 H.P.
P.Hr. 220.00
1.29.2 10 to 19 H.P.
P.Hr. 297.00
1.29.3 20 to 30 H.P.
334.00
1.3 Filling available excavated earth (excluding rock) in
trenches, plinth side of foundation etc. in layers not
exceeding 20 cm. in depth, consolidating each deposited
layer by ramming and watering including lead up to 50 meter
and with all lift.
P.Cum 62.00
1.31 Add extra for foundation/trenches/drains for every additional
lift of 1.5 Mtr. or part thereof upto 4.5mtr. depth :
P. 100 740.00
Sqm
1.35 Ploughing the existing ground to a depth of 15 cm to 25 cm
and watering the same:
1.35.1 All Kinds of soil.
P. 100 752.00
Sqm
1.36 Excavating holes up to 0.5cum including getting out the
excavated soil then returning the soil as required in layers
not exceeding 20 cm in depth including consolidating each
deposited layer by ramming watering etc. and disposing of
surplus excavated soil
P.Sqm 605.00
1.4 Providing and injecting by hand operated pressure pumps
chemical Emulsion timber ground treatment [TCGT] in ratio
1: 2 as per manufacturers specification for POST
CONSTRUCTIONAL Anti-termite treatment (as per IS 6313)
part - III 1971 as amended from time
P.Mtr. 47.00
1.40.2 Along the external wall below concrete or masonry apron
using chemical emulsion @ 2.25Liters per linear meter
including drilling and plugging holes etc With
Chloropyrifos /Lindane E.C 20 % with 1% concentration.
P.Mtr. 52.00
1.40.3 Treatment of soil under existing floors using chemical
emulsion @ one liter per hole, 300mm apart including
drilling 12 mm diameter holes and plugging with cement
mortar 1: 2 (1 cement: 2 coarse sand) to match the existing
floor.
P.Mtr. 204.00
1.41 Ceiling / Shamyana with Iron holow poles of standard size
as per design including all accessories used in 15'x15' with
height upto 12' complete for one day period including
removal & cleaning the site complete in all respect as per
instruction given by En
Each 110.00
1.41.1 Add extra for above item for water proofing Shamyana 25%
P.Sqm 375.00
1.43 Kanat with bamboo as per design and height upto 1.50m
with all accessories for one day period including removal &
cleaning the site complete in all respect as per instruction
given by Engineer Incharge (on rent)
P.Rmt 8.00
P.Sqm 1.00
1.46 Anti-termite treatment of existing floor and wall using Sqm 82.00
Imidacloprid 30.5% EC non repellent, odorless, low dose,
environimentally safe Termiticide with rapid action non
corrosive stain free manufactured by Bayer or equivalent
company by injecting the emul
1.47 Anti termite treatment of floor using Imidacloprid 30.5% EC Sqm 196.00
non repellent, odorless, low dose, environmentally safe
terniticide with rapid action non corrosive stain free
manufactured by Bayer or equivalent company by drilling
12mm diameter holes 300mm ap