Professional Documents
Culture Documents
Page 3 of 127
Owner Medford Water Comission Computed By AVS
Plant WQIP_Chemical building Unit Date Jan 31, 2020
Project No. 402845 File No. Verified By
Title Big Butte WTP Date
BLACK & VEATCH Page of
CALCULATIONS:
Ie = Importance Factor 1.25 Section 11.5.1 &
Table 1.5-2
Site Coefficients:
Fa = Site Coefficient based on 0.2-sec Short Period 1.302 Table 11.4-1 Table 1613.2.3(1)
Fv = Site Coefficient based on 1-sec Period 1.999 Table 11.4-2 Table 1613.2.3(2)
Maximum Considered Earthquake Response Acceleration:
SMS = Fa*SS/100 = 0.810 (Eqn 11.4-1) (Eqn 16-37)
SM1 = Fv*S1/100 = 0.602 (Eqn 11.4-2) (Eqn 16-38)
Design Spectral Response Accelerations:
SDS = (2/3)SMS SDS = 0.540 (Eqn 11.4-3) (Eqn 16-38)
SD1 = (2/3)SM1 SD1 = 0.401 (Eqn 11.4-4) (Eqn 16-39)
Determine Seismic Design Category
Seismic Design Category,0.2-sec Period D Table 11.6-1 Table 1613.2.5(1)
Seismic Design Category, 1-Sec Period N/A Exclude < Use or Exclude? Table 11.6-2 Table 1613.2.5(2)
Determine Periods (Time) for Response Spectra Curve:
Ta = Approximate Fundamental Period of the Structure
= Ct*hnx 0.020*(24.00)^0.75 = 0.217 sec (Eqn 12.8-7)
T0 = 0.2*(SD1/SDS) = 0.20*0.401/0.540 = 0.149 sec Section 11.4.6
TS = (SD1/SDS) = 0.401/0.540 = 0.743 sec Section 11.4.6
Base Shear (ASD) VASD = 0.7*VLFD = 0.158 *W VASD*W0 = 0.394 *W Section 2.4 ASD Load Combinations
10.5 ft
Max.5.0 ft
INPUT
Type of Grating = Hot Dipped Galvanized Steel
Weight of grating 7.4 psf = 0.0074 ksf 7.4/1000
Maximum span of grating for design = 5.0 ft
Thickness of grating = 1.25 in
Grating supporting member (1) = W 10 X 45
Maximum length of grating supporting member = 10.5 ft
A DEAD LOAD
Self weight of grating supporting member = as calculated in STAAD
Self weight of Grating = 0.0074 ksf
Load transferred on supporting member = 0.0185 kip/ft 0.0074*5/2
B LIVE LOAD
Live load on Operating floor 150 psf = 0.15 ksf 150/1000
Load transferred on supporting member = 0.375 kip/ft 0.15*5/2
C SEISMIC LOAD
SDS = 0.540
Max. Base shear coefficient of Superstructure Cs = 0.225 W refer sesimic base shear calculation
Self weight multiplied by the coefficient = as calculated in STAAD
Load due to grating = 0.00416 kip/ft 0.225*0.0185
Page 3 of 127
Job No Sheet No Rev
402845 1 0
Geometry of structure-
Rendered view -
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Job No Sheet No Rev
402845 1 0
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Job No Sheet No Rev
402845 1 0
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Job No Sheet No Rev
402845 1 0
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Job No Sheet No Rev
402845 1 0
0.017 inch
0.013 inch
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Job No Sheet No Rev
402845 1 0
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
CONNECTION DESIGN FOR
ANGLE
Page 3 of 127
Job No Sheet No Rev
402845 1 0
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 1
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + HAS-R 316 1/2
Effective embedment depth: hef,act = 6.000 in. (hef,limit = - in.)
Material: ASTM F 593
Evaluation Service Report: ESR-3187
Issued I Valid: 11/1/2016 | 3/1/2018
Proof: Design method ACI 318-14 / Chem
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.250 in.
Anchor plate: lx x ly x t = 24.000 in. x 2.500 in. x 0.250 in.; (Recommended plate thickness: not calculated
Profile: Rectangular plates and bars (AISC); (L x W x T) = 0.250 in. x 0.188 in. x 0.000 in.
Base material: cracked concrete, 4000, fc' = 4000 psi; h = 10.000 in., Temp. short/long: 32/32 °F
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 2
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
3 Tension load
Load Nua [lb] Capacity f Nn [lb] Utilization bN = Nua/f Nn Status
Steel Strength* 1000 9223 11 OK
Bond Strength** 1000 3887 26 OK
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Strength** 1000 5140 20 OK
* anchor having the highest loading **anchor group (anchors in tension)
Variables
Ase,N [in.2] futa [psi]
0.14 100000
Calculations
Nsa [lb]
14190
Results
Nsa [lb] f steel f Nsa [lb] Nua [lb]
14190 0.650 9223 1000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 3
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Na = (AA ) y
Na
Na0
ed,Na y cp,Na Nba ACI 318-14 Eq. (17.4.5.1a)
f Na ≥ Nua ACI 318-14 Table 17.3.1.1
ANa = see ACI 318-14, Section 17.4.5.1, Fig. R 17.4.5.1(b)
ANa0 = (2 cNa)2 ACI 318-14 Eq. (17.4.5.1c)
cNa = 10 da √
t uncr
1100
ACI 318-14 Eq. (17.4.5.1d)
( )
1
y ec,Na = e' ≤ 1.0 ACI 318-14 Eq. (17.4.5.3)
1+ N
cNa
y ed,Na = 0.7 + 0.3 ( )
ca,min
cNa
≤ 1.0 ACI 318-14 Eq. (17.4.5.4b)
y cp,Na = MAX ( ,)
ca,min cNa
cac cac
≤ 1.0 ACI 318-14 Eq. (17.4.5.5b)
Nba = l a · t k,c · p · da · hef ACI 318-14 Eq. (17.4.5.2)
Variables
t k,c,uncr [psi] da [in.] hef [in.] ca,min [in.] t k,c [psi]
2327 0.500 6.000 2.500 1174
ec1,N [in.] ec2,N [in.] cac [in.] la
0.000 0.000 15.324 1.000
Calculations
cNa [in.] ANa [in.2] ANa0 [in.2] y ed,Na
7.239 141.01 209.62 0.804
y ec1,Na y ec2,Na y cp,Na Nba [lb]
1.000 1.000 1.000 11064
Results
Na [lb] f bond f Na [lb] Nua [lb]
5981 0.650 3887 1000
Ncb = (AA ) y
Nc
Nc0
ed,N y c,N y cp,N Nb ACI 318-14 Eq. (17.4.2.1a)
f Ncb ≥ Nua ACI 318-14 Table 17.3.1.1
ANc see ACI 318-14, Section 17.4.2.1, Fig. R 17.4.2.1(b)
ANc0 = 9 h2ef ACI 318-14 Eq. (17.4.2.1c)
( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-14 Eq. (17.4.2.4)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef
≤ 1.0 ) ACI 318-14 Eq. (17.4.2.5b)
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac
≤ 1.0 ) ACI 318-14 Eq. (17.4.2.7b)
1.5
Nb = kc l a √fc hef
'
ACI 318-14 Eq. (17.4.2.2a)
Variables
hef [in.] ec1,N [in.] ec2,N [in.] ca,min [in.] y c,N
6.000 0.000 0.000 2.500 1.000
Calculations
ANc [in.2] ANc0 [in.2] y ec1,N y ec2,N y ed,N y cp,N Nb [lb]
207.00 324.00 1.000 1.000 0.783 1.000 15802
Results
Ncb [lb] f concrete f Ncb [lb] Nua [lb]
7908 0.650 5140 1000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 4
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
4 Shear load
Load Vua [lb] Capacity f Vn [lb] Utilization bV = Vua/f Vn Status
Steel Strength* 1000 5109 20 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Bond Strength 1000 8373 12 OK
controls)**
Concrete edge failure in direction y+** 1000 6861 15 OK
* anchor having the highest loading **anchor group (relevant anchors)
Variables
Ase,V [in.2] futa [psi] (0.6 Ase,V futa) [lb]
0.14 100000 8515
Calculations
Vsa [lb]
8515
Results
Vsa [lb] f steel f Vsa [lb] Vua [lb]
8515 0.600 5109 1000
( )
1
y ec,Na = e' ≤ 1.0 ACI 318-14 Eq. (17.4.5.3)
1+ N
cNa
y ed,Na = 0.7 + 0.3 ( ) ca,min
cNa
≤ 1.0 ACI 318-14 Eq. (17.4.5.4b)
y cp,Na = MAX ( )
ca,min cNa
,
cac cac
≤ 1.0 ACI 318-14 Eq. (17.4.5.5b)
Nba = l a · t k,c · p · da · hef ACI 318-14 Eq. (17.4.5.2)
Variables
kcp t k,c,uncr [psi] da [in.] hef [in.] ca,min [in.] t k,c [psi]
2 2327 0.500 6.000 2.500 1174
ec1,N [in.] ec2,N [in.] cac [in.] la
0.000 0.000 15.324 1.000
Calculations
cNa [in.] ANa [in.2] ANa0 [in.2] y ed,Na
7.239 141.01 209.62 0.804
y ec1,Na y ec2,Na y cp,Na Nba [lb]
1.000 1.000 1.000 11064
Results
Vcp [lb] f concrete f Vcp [lb] Vua [lb]
11961 0.700 8373 1000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 5
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Vcb = (AA ) y
Vc
Vc0
ed,V y c,V y h,V y parallel,V Vb ACI 318-14 Eq. (17.5.2.1a
f Vcb ≥ Vua ACI 318-14 Table 17.3.1.1
AVc see ACI 318-14, Section 17.5.2.1, Fig. R 17.5.2.1(b)
AVc0 = 4.5 c2a1 ACI 318-14 Eq. (17.5.2.1c)
( )
1
y ec,V = 2e'v ≤ 1.0 ACI 318-14 Eq. (17.5.2.5)
1+
3ca1
y ed,V = 0.7 + 0.3 ( ca2
1.5ca1 )
≤ 1.0 ACI 318-14 Eq. (17.5.2.6b)
y h,V = √1.5ca1
ha
≥ 1.0 ACI 318-14 Eq. (17.5.2.8)
(( ) )
0.2
l 1.5
Vb = 7 e √da l a √f'c ca1 ACI 318-14 Eq. (17.5.2.2a)
da
Variables
ca1 [in.] ca2 [in.] ecV [in.] y c,V ha [in.]
8.000 12.000 0.000 1.000 10.000
Calculations
AVc [in.2] AVc0 [in.2] y ec,V y ed,V y h,V Vb [lb]
240.00 288.00 1.000 1.000 1.095 10737
Results
Vcb [lb] f concrete f Vcb [lb] Vua [lb]
9801 0.700 6861 1000
6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Condition A applies when supplementary reinforcement is used. The Φ factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to your local standard.
• Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions
• Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI 318 or the relevant
standard!
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. Reference ACI 318-14,
Section 17.8.1.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 6
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
7 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + HAS-R 316 1/2
Profile: Rectangular plates and bars (AISC); 0.250 x 0.188 x 0.000 in. Installation torque: 360.001 in.lb
Hole diameter in the fixture: df = 0.563 in. Hole diameter in the base material: 0.563 in.
Plate thickness (input): 0.250 in. Hole depth in the base material: 6.000 in.
Recommended plate thickness: not calculated Minimum thickness of the base material: 7.250 in.
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to instructions for use is required
12.000 12.000
1.250 1.250
1.250 1.250
1 x
12.000 12.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 7
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
CONNECTION DESIGN FOR
W10X45
Page 3 of 127
Typical Shear
connection with RCC
W10X45
Print Time/Date: 29/01/2020 12:03 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 1
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + HAS-R 316 3/4
Effective embedment depth: hef,act = 6.000 in. (hef,limit = - in.)
Material: ASTM F 593
Evaluation Service Report: ESR-3187
Issued I Valid: 11/1/2016 | 3/1/2018
Proof: Design method ACI 318-14 / Chem
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.500 in.
Anchor plate: lx x ly x t = 14.000 in. x 11.000 in. x 0.500 in.; (Recommended plate thickness: not calculated
Profile: W shape (AISC); (L x W x T x FT) = 10.100 in. x 8.020 in. x 0.350 in. x 0.620 in.
Base material: cracked concrete, 4000, fc' = 4000 psi; h = 12.000 in., Temp. short/long: 32/32 °F
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 2
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
3 Tension load
Load Nua [lb] Capacity f Nn [lb] Utilization bN = Nua/f Nn Status
Steel Strength* N/A N/A N/A N/A
Bond Strength** N/A N/A N/A N/A
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Strength** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (anchors in tension)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 3
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
4 Shear load
Load Vua [lb] Capacity f Vn [lb] Utilization bV = Vua/f Vn Status
Steel Strength* 900 10236 9 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Bond Strength 3601 14349 26 OK
controls)**
Concrete edge failure in direction x+** 3601 4649 78 OK
* anchor having the highest loading **anchor group (relevant anchors)
Variables
Ase,V [in.2] futa [psi] (0.6 Ase,V futa) [lb]
0.33 85000 17060
Calculations
Vsa [lb]
17060
Results
Vsa [lb] f steel f Vsa [lb] Vua [lb]
17060 0.600 10236 900
( )
1
y ec,Na = e' ≤ 1.0 ACI 318-14 Eq. (17.4.5.3)
1+ N
cNa
y ed,Na = 0.7 + 0.3 ( )ca,min
cNa
≤ 1.0 ACI 318-14 Eq. (17.4.5.4b)
y cp,Na = MAX ( )
ca,min cNa
,
cac cac
≤ 1.0 ACI 318-14 Eq. (17.4.5.5b)
Nba = l a · t k,c · p · da · hef ACI 318-14 Eq. (17.4.5.2)
Variables
kcp t k,c,uncr [psi] da [in.] hef [in.] ca,min [in.] t k,c [psi]
2 2327 0.750 6.000 5.000 1273
ec1,N [in.] ec2,N [in.] cac [in.] la
0.000 0.000 11.536 1.000
Calculations
cNa [in.] ANa [in.2] ANa0 [in.2] y ed,Na
10.859 320.38 471.66 0.838
y ec1,Na y ec2,Na y cp,Na Nba [lb]
1.000 1.000 1.000 18003
Results
Vcpg [lb] f concrete f Vcpg [lb] Vua [lb]
20499 0.700 14349 3601
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 4
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Vcbg = (AA ) y
Vc
Vc0
ec,V y ed,V y c,V y h,V y parallel,V Vb ACI 318-14 Eq. (17.5.2.1b)
f Vcbg ≥ Vua ACI 318-14 Table 17.3.1.1
AVc see ACI 318-14, Section 17.5.2.1, Fig. R 17.5.2.1(b)
AVc0 = 4.5 c2a1 ACI 318-14 Eq. (17.5.2.1c)
( )
1
y ec,V = 2e'v ≤ 1.0 ACI 318-14 Eq. (17.5.2.5)
1+
3ca1
y ed,V = 0.7 + 0.3 (ca2
1.5ca1 )
≤ 1.0 ACI 318-14 Eq. (17.5.2.6b)
y h,V = √
1.5ca1
ha
≥ 1.0 ACI 318-14 Eq. (17.5.2.8)
' 1.5
Vb = 9 l a √fc ca1 ACI 318-14 Eq. (17.5.2.2b)
Variables
ca1 [in.] ca2 [in.] ecV [in.] y c,V ha [in.]
8.000 5.000 0.000 1.000 12.000
Calculations
AVc [in.2] AVc0 [in.2] y ec,V y ed,V y h,V Vb [lb]
180.00 288.00 1.000 0.825 1.000 12880
Results
Vcbg [lb] f concrete f Vcbg [lb] Vua [lb]
6641 0.700 4649 3601
5 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Condition A applies when supplementary reinforcement is used. The Φ factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to your local standard.
• Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions
• Checking the transfer of loads into the base material and the shear resistance are required in accordance with ACI 318 or the relevant
standard!
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. Reference ACI 318-14,
Section 17.8.1.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 5
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
6 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + HAS-R 316 3/4
Profile: W shape (AISC); 10.100 x 8.020 x 0.350 x 0.620 in. Installation torque: 1200.002 in.lb
Hole diameter in the fixture: df = 0.813 in. Hole diameter in the base material: 0.875 in.
Plate thickness (input): 0.500 in. Hole depth in the base material: 6.000 in.
Recommended plate thickness: not calculated Minimum thickness of the base material: 7.750 in.
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to instructions for use is required
7.000 7.000
3.000
5.500
3 4
5.000
x
5.500
1 2
3.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.us Profis Anchor 2.7.3
Company: B&V Page: 6
Specifier: AVS Project: MWC WQIP
Address: Sub-Project I Pos. No.: Chemical Building BB
Phone I Fax: | Date: 1/31/2020
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan