The document is a question paper for a Process Instrumentation course. It contains 10 multiple choice questions in the first section asking about various pressure and flow measurement instruments. The second section asks to explain how electromagnetic flow meters work including a diagram and advantages/limitations. The third section asks to describe vacuum pressure gauges used to measure 10-1 to 10-5 torr including necessary equations. The remaining questions cover additional topics like pressure sensor types, flow meter calibration techniques, and constant temperature anemometers.
The document is a question paper for a Process Instrumentation course. It contains 10 multiple choice questions in the first section asking about various pressure and flow measurement instruments. The second section asks to explain how electromagnetic flow meters work including a diagram and advantages/limitations. The third section asks to describe vacuum pressure gauges used to measure 10-1 to 10-5 torr including necessary equations. The remaining questions cover additional topics like pressure sensor types, flow meter calibration techniques, and constant temperature anemometers.
The document is a question paper for a Process Instrumentation course. It contains 10 multiple choice questions in the first section asking about various pressure and flow measurement instruments. The second section asks to explain how electromagnetic flow meters work including a diagram and advantages/limitations. The third section asks to describe vacuum pressure gauges used to measure 10-1 to 10-5 torr including necessary equations. The remaining questions cover additional topics like pressure sensor types, flow meter calibration techniques, and constant temperature anemometers.
(An Autonomous Institute Affiliated to VTU, Belagavi) ShavigeMalleshwara Hills, Kumaraswamy Layout, Bengaluru-560078
DEPARTMENT OF ELECTRONICS & INSTRUMENTATION ENGINEERING
CONTINUOUS INTERNAL EVALUATION – 2 Course: Process Instrumentation Maximum marks: 50 Course Code: 18EI4DCPCI Duration: 90 Min Semester: IV Date:22/04/2020 Course Coordinator: Dr V S Krushnasamy Question number 1, 2, and 3 are compulsory. Choose any one from question 4 or 5 SL. CO MARKS Note: Maximum Of 4 Sub Questions Are Allowed. NO 1 i The pressure gauges are calibrated using ----------- a)Dead Weight Tester b)Bourdon Tube c) Bellows d) Strain gauges ii ------- gauge measures pressure by sensing changes in the thermal conductivity of a gas. a) McLeod gauge b) Slack diaphragm gauge c) Pirani gauge 𝒅) All of the above iii In Bellows the spring is provided to -------------- a) Increase sensitivity b) Increase operating range c) Increase linearity d) Decrease hysteresis effect iv Lowest vacuum pressure can be measured using ------------- a) McLeod gauge b) Thermocouple gauge c) Pirani gauge d) Ionization gauge v The Pressure less than atmospheric pressure is known as ------ a) Gauge pressure b) Static pressure c) Vacuum pressure d) CO2 absolute pressure CO3 1*10 vi -------------- is not suitable for measuring the flow of a non-conducting CO6 flow. (L1) a) Rotameter b) Electro-magnetic flow meter c) Orifice plate d)Venturi meter vii Gas velocities can be measured using -------- a) Rotameter b) Electro-magnetic flow meter c) Nozzle d) Hot wire anemometer viii A quantity flow meter is also called as -------- a) A variable flow meter b) Positive displacement flow meters c) Differential pressure flow meter d)None of the above ix ----------- are used for measurement of flow rates of clean fluids and fluids containing solids. a) Eccentric orifice plates b) Venturi meter c) Rotameter D)None of above x Dynamic pressure can be measured using -------------------- a)Pitot static tube b) Orifice plate c)Venture meter d) Nozzle 2 How the flow rate of a conducting fluid is measured, When it is flowing CO2,CO through a non-magnetic and non-conduction pipe. With necessary diagram, 3,CO6 10 explain the working principle, construction and operation of the same. List (L3) its advantages and limitations also. 3 Describe the vacuum pressure gauge which is used to measure pressure CO2,CO range of (𝟏𝟎−𝟏 𝒕𝒐 𝟏𝟎−𝟓 𝒕𝒐𝒓𝒓) .With neat sketches and necessary equations 3,CO6 10 explain the same. (L3) 4a (i) List the types of pressure measurement CO2,CO (ii) Is it possible using a gravitational transducer we can calibrate a 02 3,CO6 pressure gauge. If it is yes explain the procedure to calibrate the 08 (L3) pressure gauge. (OR) 4b Describe the following elastic pressure sensors with neat sketches highlighting their types, characteristics, range and material compositions. CO2,CO 03 (i) Bourdons Tube 3,CO6 03 (ii) Diaphragms (L3) 04 (iii) Bellows 5a Which flow meter (probe) is used to measure flow velocity in terms of point CO2,CO pressure measurement .Describe the operation of total pressure probe 3,CO6 10 with neat sketches. (L3) (OR) 5b CO2,CO With necessary diagram explain the principle and working of constant 3,CO6 10 temperature, constant current anemometers. (L3)