Professional Documents
Culture Documents
This manual provides rules and guidelines which will help you use this machine safely and
effectively. The precautions in this manual must be followed at all times when performing
operation and maintenance. Most accidents are caused by the failure to follow fundamental
safety rules for the operation and maintenance of machines. Accidents can be prevented by
knowing beforehand conditions that may cause hazard when performing operation and
maintenance.
Operators and maintenance personnel must always do as follows before beginning operation or
maintenance.
z Always be sure to read and understand this manual thoroughly before performing operation
and maintenance.
z Read the safety message given in this manual and the safety labels affixed to the machine
thoroughly and be sure that you understand them fully.
z This manual should be considered as a permanent part of your machine. If you sell the
machine, be sure to give this manual to the new owners together with the machine.
z Only original spare parts procured from Sunward are to be used. To use parts of poor quality
will be detrimental to machine’s overall performance.
z All operation described in this instruction manual should be carried out exclusively by
trained and qualified staff.
z This machine is designed in metric system and the sizes provided in this manual are metric,
therefore, please only use parts and tools in metric system.
Sunward guarantees maintenance to our customers. Please refer to guarantee certificate which
you have obtained from our distributors for maintenance concerns. With a guarantee certificate,
you are entitled to get maintenance from Sunward. In some cases even beyond maintenance
period, Sunward provides maintenance on the spot, which is usually free of charge. However, if
machine is abused or kept in overloading operations or its performance is changed beyond our
original regulations, compensations for maintenance will be unavailable and service on the spot
will probably be refused.
All the information including charts and specifications in this manual is the latest that we
can get. We reserve the right to make without prior notice any modification or amendment to
machine component.
TABLE OF CONTENTS
1 Safety rules................................................................................................................................ 3
1.1 Safety mark...................................................................................................................... 3
1.2 Safety label ...................................................................................................................... 3
1.3 General safety instruction .................................................................................................. 3
1.4 Preparation for emergency ................................................................................................. 4
1.5 Wear safety protective articles ............................................................................................ 4
1.6 Check machine before start-up............................................................................................ 4
1.7 Adjust operator seat........................................................................................................... 4
1.8 Enter or leave machine correctly ......................................................................................... 4
1.9 Start engine correctly......................................................................................................... 5
1.10 Forbid hitching other people ............................................................................................. 5
1.11 Keep machine away from electricity transmission line ......................................................... 5
1.12 Move machine safely ....................................................................................................... 5
1.13 Prevent accident while backing or swinging ....................................................................... 6
1.14 Operate digging work safely ............................................................................................. 6
1.15 Avoid accident with losing control ..................................................................................... 7
1.16 Park machine safely ........................................................................................................ 7
1.17 Safe maintenance ............................................................................................................ 8
1.18 Support machine correctly ................................................................................................ 8
1.19 Clean trash on the machine ............................................................................................... 9
1.20 Prevent battery exploding ................................................................................................. 9
1.21 Store parts safely............................................................................................................. 9
1.22 Prevent splash objects ...................................................................................................... 9
1.23 Prevent parts flying off .................................................................................................... 9
1.24 Keep away from transmission parts ................................................................................. 10
1.25 Prevent inhaling asbestos dust......................................................................................... 10
1.26 Beware of inhaling fog or exhaust gas.............................................................................. 10
1.27 Beware of scald ............................................................................................................ 10
1.28 Be careful of pressure liquids.......................................................................................... 10
1.29 Avoid heating up near pressure oil pipe ............................................................................ 11
1.30 Avoid heating up inflammable liquid pipe ........................................................................ 11
1.31 Remove paint before welding or heating .......................................................................... 11
1.32 Dispose of liquid safely ................................................................................................. 12
1.33 Dispose of chemical safely ............................................................................................. 12
1.34 Avoid fire ..................................................................................................................... 12
1.35 Emergency exit ............................................................................................................. 13
1.36 Noise ........................................................................................................................... 13
1.37 Other safety marks ........................................................................................................ 13
2. Machine familiarization............................................................................................................ 15
2.1 Cabin ............................................................................................................................ 16
2.2 Monitor panel ................................................................................................................. 17
2.3 Control panel ................................................................................................................. 18
2.5 Seat adjustment .............................................................................................................. 20
2.6 Air conditioner ............................................................................................................... 21
1
Operator’s Manual SWE80/80H
2
Operator’s Manual SWE80/80H
1 Safety rules
1.1 Safety mark
Attention: The safety instructions in this book only include the general safety rules of
machine. They can’t cover all the possible danger may occur. If there is any problem,
please report to your superior before operate and maintain the machine.
3
Operator’s Manual SWE80/80H
Hard hat
Safety gloves
Earplug or earcape
5
Operator’s Manual SWE80/80H
When the machine work on slope, the track should park along the slope, retract the bucket
as much as possible, keep the bucket close to ground and machine, and pay attention to
avoid turning over.
When swing with load, it must decrease swing speed to avoid turning over. When working
on frozen ground, it should prevent the ascending temperature causing the ground soften,
otherwise it will affect the stability of machine.
(3) During operation, prevent boom or arm colliding with high objects.
(4) The bucket only for digging work, not allow operating bucket to work as pneumatic pick
or hydraulic breaker does.
When the machine loses control, if someone tries to mount on or stop moving machine, it
will cause GBH or death.
8
Operator’s Manual SWE80/80H
The stored parts, such as bucket, hydraulic breaker, etc, are likely to fall down, cause
GBH or death.
By all effective means, store parts and machine safely to prevent falling down. Don’t
permit unauthorized people, especially children, close to the parts storage area.
9
Operator’s Manual SWE80/80H
Effluent liquids in high pressure will penetrate through skin, causing GBH.
10
Operator’s Manual SWE80/80H
Touching deleterious chemical directly will cause serious injury to human body. The
chemical using in excavator, such as lubricant, coolant, dope, and adhesive, may be deleterious.
Before using deleterious chemical, you should check and understand its danger, know how
to operate safely, and use recommended implement to work.
Before everyday operation, check the function of key switch and engine emergency stop
switch. If there is any unusuality, must repair at once. In case of fire, if you can’t stop
engine, it will aggravate firepower, and may cause GBH.
z Clean out inflammable materials
Spilled fuel, stored breeze, and other inflammable materials, may cause fire. Keep the
machine clean every day to prevent fire.
Attention:
(1) Pay attention not to be hurt by the splashing objects while breaking the window
with a certain distance to the breaking hole for safety.
(2) The breaking hole should be big enough for operator to get out (according to
operator’s own condition) and the hole should have no sharp spines for safety.
1.36 Noise
The machine meets the requirements of noise instruction 2000/14/EC and standard EN474-1,
EN474-5, noise instruction is as follows:
Noise at operator’s position:LpA= 80.2 dB
Machine noise:LW= 97.0 dB
13
Operator’s Manual SWE80/80H
z Warning:Please do not get near to the machine when machine working equipment is being
operated.
z Warning: Please stay away from the loader arm clearance area.
14
Operator’s Manual SWE80/80H
2. Machine familiarization
Machine name
SW E 80 H
Additive function(H: no boom swing)
(Blank:equipped with boom swing struction)
Excavator
SUNWARD
Note: The above weight figures are measured with the following five requirements: 1. Diesel
oil tank is full (diesel oil instrument displays full); 2. Hydraulic oil is enough ; 3. Water tank
antifreeze fluid is enough; 4. Sealing plate is assembled; 5. Driver’s weight is not included
15
Operator’s Manual SWE80/80H
2.1 Cabin
Cabin picture
16
Operator’s Manual SWE80/80H
When water temperature is normal, there isn’t indication. When the temperature is too
high, this indicator flickers and buzzer alarms.
9 — Hydraulic oil temperature warning indicator
If hydraulic oil temperature is normal, there isn’t indication; when the temperature is too
high, this indicator flickers and buzzer alarms.
10 — Warming up indicator
Start engine in cold weather, place the key at warming up
position, the indicator comes on, and the light will go out after
dozens of seconds, means the warming up finished.
11 — Charging indicator
When generator works normally, this indicator comes on;
contrarily, there isn’t indication, means the generator doesn’t
work.
12 — Air filter clogged indicator lamp
When the air filter core is clogged, red indicator light comes on. Please clean or replace
outer core.
13 — Hydraulic oil pollution indicator
This device indicates the working condition of hydraulic oil filter. When the hydraulic oil
filter is normal, there is not indication in this device; when filter is clogged, this indicator
blinks and the buzzer alarms.
This switch turns cabin wiper on and off. When press this switch, wiper begin to work,
green light comes on; press this switch again, green light goes out, wiper stop work.
4 — Cleaner switch
This switch turns washing water on and off. When press this switch, washing water
begins to work, the light comes on; press this switch again, the light goes out, washing
water is turned off.
5 — Warning light switch
This switch turns the warning light on and off. When turn on warning light, the switch
light comes on; when turn off warning light, the switch light goes out.
6 — High speed traveling switch
Press this switch, green light comes on, the machine is on high speed condition; press
this switch again, green light goes out, the machine is on low speed condition.
7 — Breaking/swing switch (optional)
This switch controls the movement conversion between bulldozing and turning arm works
(if the machine equipped with turning arm)
8 — Conversion switch (optional)
This switch controls the movement conversion between bulldozing and turning arm
works (if the machine equipped with turning arm)
9 — Key switch
① — HEAT (preheating)
② — OFF (engine stop)
③ — ON (power on)
④ — START (start engine)
10 — Cigar kindling device
Press this device, it will rebound after few seconds, take it out and kindle cigarette.
4. Radio/CD
Strong aseismatic and dustproof CD423 is beautiful and durable.
19
Operator’s Manual SWE80/80H
Recliner knob B
Slider knob D
SG7-8 model is a specially designed deluxe driver seat for construction machineries. The
backrest and cushion are both designed according to the body engineering ergonomics, which
offers the driver the most comfort. The seat is assembled with a suspension device, which can
help to reduce harmful vibration effectively and ease the fatigue of the driver.
Technical Features
(1) The Forward and afterward travel of the seat is 125mm(For:90mm,Aft:35mm)
(2) The stepless adjustable angle scope of the backrest:55 degree – 175 degree
(3) Height adjustable scope:0-60mm;every pitch:20mm.
(4) Operator weight scope:50kgs-130kgs
(5) Max. suspension travel:60mm
(6) Headrest adjustable angle scope:10 degrees; headrest adjustable height scope:60mm
(7) The adjustable armrest can be adjusted between -45 To 90 degrees.
Operation Instructions
(1) Weight adjustment
According to the operator’s own weight, rotate the weight adjustment knob until you feel
comfortable. Rotate the knob anti-clockwise, the suspension stiffness will come down; Rotate
the knob clockwise, the suspension stiffness will rise.
(2) For & Aft adjustment
Put up the adjustment knob with your hand, then pull or push knob D forward or backward
to the proper position you want, and then release the knob, the slider will lock automatically.
(3) Height adjustment
The height riser can be adjusted circularly. When need to adjust the height, the operator
stands in front of the seat, put up knob C until there is a clear lock sound, then release the knob,
by which the adjustment is done; When you adjust the seat to the highest position, you release
the knob, the height riser will go to the lowest position automatically.
(4) Backrest adjustment
Put up recliner knob B, then rotate the backrest to the proper position you want, release the
knob to lock the backrest.
(5) Armrest adjustment
20
Operator’s Manual SWE80/80H
When adjusting the armrest angle, put up the armrest to the proper angle, then rotate the
adjustment knob until it is in the locking position, by which the adjustment is done.
Caution
(1) Only adjust the seat when the driver is in safety condition
(2) For slider and recliner adjustment, please make sure the knob is in the proper
position; only when the adjustment mechanism parts are separate, then do the
adjustment.
(3) After all the adjustments, please make sure every knob stays in the proper
position and every part is locked.
The seat of the machine meets the requirements of EN ISO 7096:2000.
A
B
Operation marks:
The machine equipped with left and right pilot control
joystick.
The right joystick controls following movements:
a —— lift boom
b —— lower boom
21
Operator’s Manual SWE80/80H
g —— extend arm
h —— retract arm
22
Operator’s Manual SWE80/80H
Front window and top cover can easily be opened for maintenance and leaving purpose.
Open fastening of top cover, hold plastic handle and push upwards, it can open top cover; open
fastening of front window, push the glass window upwards and backwards to the scheduled
position, then fasten glass window
固定扣
Upper-cover
The upper-cover can protect the hydraulic components, electric circuit in
the interior of the excavator and ensures the beautiful appearance. It is
fixed on the platform and also protects engine.
23
Operator’s Manual SWE80/80H
Accessory list
No. Name
1 O-lock ring 85X7 GB3452.1
2 O-lock ring 61.5X3.55 GB3452.1
3 O-lock ring 71X3.55 GB3452.1
4 O-lock ring 145X5.3 GB3452.1
5 Oil cup M10X1(made of steel) GB1152 imported
6 Combination washer 16 JB982
7 Combination washer 33 JB982
8 Scraper seal DLW 05502
9 Scraper seal DLW06003 75X60X5
10 Scraper seal DLW12001 140X120X10
11 Pin 12X75 GB119
12 Column pin 12X80 GB119
13 Elastic spring
14 Elastic spring
15 Elastic spring
16 Lateral bucket tooth PC100
17 Lateral pin PC100
18 Pilot filter core PFX-20X10
19 Filter core RE400B
20 Inlet filter coreWUX-200X80-J
24
Operator’s Manual SWE80/80H
Tool list
25
Operator’s Manual SWE80/80H
2.13 Identifier
26
Operator’s Manual SWE80/80H
3. Machine operation
3.1 Machine working environment
Daily inspection
(1) Electric system
Check whether there are abraded or cracked wire and slack connector or not, and check
27
Operator’s Manual SWE80/80H
Place the machine on a horizontal ground, check the engine oil level (stop engine, the engine
oil will return to the tank 15 minutes later)
Electric device
Air filter
【Important】
(1) Place machine on horizontal ground and retract all hydraulic cylinders, the oil level
doesn’t allow to exceed MAX mark.
(2) Similarly, when all hydraulic cylinders extend, the oil level should be not lower than
the MIN mark.
(3) It should choose recommended oil according to the Lubricant List.
(4) All filled hydraulic oil must pass through returning oil filter.
Start engine
(1) Keep pilot valve control lever locked.
(2) Turn key switch to ON position.
(3) Beep horn to warn surrounding people.
(4) Start engine by turning key switch clockwise to START position, release key, the
switch will return ON position.
【Important】 In order to avoid damage of starter, never operate motor starter 10
seconds or more every time. If the engine can’t start, turn the key switch to OFF position
and wait at least 2 minutes, then try again. After wrong start, the engine should be
stopped completely, then you can turn key switch, otherwise it may damage starter.
29
Operator’s Manual SWE80/80H
bottommost, engine runs at minimum load; adjust accelerograph between upmost and
bottommost to adjust engine revs, and also you can screw handle to adjust accelerograph
imperceptibly.
Stop engine
【Important】 Don’t stop engine directly when it is full loaded, it should stop engine
after 5 minutes minimum loaded operation to unload the heat load and avoid possible
damage to engine. If engine stop with load, it should remove load and start engine at
once.
(1) Lower the bucket to ground.
(2) Place the accelerograph handle to minimum load position for about 5 minutes.
(3) Screw key switch to stop engine, and take out key.
(4) Pull pilot control lever to LOCK position.
Attention:
【Important】Earth the 12V cathode (-), and only use 12V assistant battery.
When the battery exhaust, you can start engine with assistant battery.
4 Fig 1
(3) Turning in one point
Left turning (fig 2): Treadle right pedal
forward and treadle left pedal downwards.
Fig 2
Fig. 3
31
Operator’s Manual SWE80/80H
Fig 4
Fig 5
(1) Straight travel: Push 2 handles forward at the same time.
Right turning (fig 3): Pull right handle backward and push left handle forward.
32
Operator’s Manual SWE80/80H
Travel speed
During the machine traveling, press
high/low speed switch 6 on control panel, it can
achieve the shift of travel motor high/low speed,
then the machine can travel at high or low
speed.
Travel brake
Release travel pedal or travel handle, it will return natural position automatically, the
machine stop traveling.
Outline of travel
(1) Arm and bucket cylinder must be extended completely to place the working device on
minimum radius position, the bucket will be about 0.5m to the ground.
(2) Lift dozer blade to its zenith.
(3) Choose plane road to travel as much as possible. It should travel straight when
traveling or turning, and also turn large bend, avoid turing blind bend. When turn in
one point at confined area, it should operate gently.
(4) When travel at badlands or uneven carpolite road, it should reduce engine revs and
travel at about 1.5km/h to reduce the vibration.
(5) Avoid back traveling to prevent crawler parts
damaging prematurely.
900~1100
(6) If the excavator can’t travel for getting into
miriness, you can extend arm and place
bucket to ground (as figure) to lift one side of
crawler, then turn the lifted crawler to clean
out the bedload. In order to reduce the force
enduring of boom and arm, the angle between
boom and arm should be in the range of
90°--110°.
33
Operator’s Manual SWE80/80H
3.5 Excavation
Working condition
a —— Raise boom
b —— Lower boom
g —— Extend arm
h —— Retract arm
34
Operator’s Manual SWE80/80H
Attention in excavation
(1) Operator must wear safety helmet and work clothes, make sure the safety of working
area, then start machine to work.
(2) During digging work, the dozer blade should be placed on ground.
(3) During excavation, especially deep digging work, pay attention to avoid bucket teeth
colliding with dozer blade, and also avoid boom cylinder colliding with track shoe.
(4) Other people are not permitted to stand on the machine or within the range of 8m away
from working radius. When begin to work or transport with full load, operator should
ring horn to warn.
(5) Bucket should dig along the cutting track and avoid digging hard earth constrainedly,
otherwise it will cause the hydraulic oil overheated.
(6) During work, do your best to avoid pulling the handle to the end, otherwise it will
cause hydraulic oil overheated and damaging components.
(7) Not allow slewing if bucket doesn’t leave working face.
(8) It allows using arm and bucket to impel or level off rideau, but never operate side of
bucket to do that.
(9) When work at swampy ground (especially on rainy days), the excavator must keep a
proper distance away from working face to prevent collapse.
(10) After stop machine, it should shut off all switches of control panel, shut off electric
power, and lock cabin.
(11) During digging work, avoid overload work to reduce energy consumption and
hydraulic oil temperature.
(12) During digging work, pay attention to the cylinder stroke end, avoid using baffle of
boom, arm, and bucket to prolong the lifetime of framework.
(13) If the productivity can satisfy the working demand, in order to prolong engine lifetime
and keep low noise running, try your best not run at maximum accelerograph, the best
revs of engine should be 1600-1800 r/min.
(14) Before every shift, according to the rules, inject grease to all reaming connections
35
Operator’s Manual SWE80/80H
through grease nozzles until the grease overflow. Otherwise it will cause axle and
sleeves damaged.
Park excavator
(1) Place the excavator on a horizontal ground.
(2) Lower the bucket to ground.
(3) Place accelerograph handle on minimum load position for 5 minutes.
(4) Turn ignition key to “OFF” position, and take out key.
(5) Pull pilot control lever to lock position.
【Important】In order to protect the electric parts in cabin. It should close top window
and cabin door when you park the excavator.
(6) Lock all doors and compartments.
【Important】In cold weather, the excavator should be parked on hard ground to avoid
crawler and ground congealing together. If above congealment happened accidently,
please lift crawler by using boom, move excavator carefully to avoid damage drive
wheels.
Attention:
(1) Keep the angle between boom and arm in
the range of 90°--110°, and place the
bucket arc on ground.
(2) Slew superstructure 90° and lower bucket
to lift one side of crawler off ground.
Don’t dig into the ground with bucket
teeth when the machine is in backhoe
condition.
(3) Place chock under the framework to
support machine.
Avoid tilting
Avoid transverse traveling on slope. When
the machine travels on slope, the traveling
direction should be accordant with the gradient.
When upgrade and downgrade, keep the bucket pointing to the traveling direction and lifting
200-300mm to the ground. Lower bucket at once if the machine is skidding or instable.
36
Operator’s Manual SWE80/80H
When the machine slew with heavy load, it should operate carefully and operate with low
slewing speed.
Backhoe operation
(1) Place the bucket teeth on ground while
the angle between bucket bottom and
ground is 45°.
(2) Apply arm to be the main digging force,
pull bucket to the machine direction.
(3) When dirt adhered on the bucket, remove
arm and (or) bucket quickly to throw the
dirt.
(4) When dig straight trench, place crawler
parallel to the trench. After dig to required depth, remove machine to continue digging.
【Important】
(1) When lower boom, it should avoid stopping suddenly. Otherwise the impact load
may damage excavator.
(2) When operate arm, in order to prevent damaging hydraulic cylinder, it should
avoid lowering hydraulic cylinder to the bottom.
(3) Avoid bucket colliding with crawler.
(4) When digging deep trench, it should avoid boom or arm cylinder hose impacting
with ground.
Leveling operation
【Important】
Don’t apply bucket overmuch to level road surface, otherwise it will damage excavator.
37
Operator’s Manual SWE80/80H
Don’t push or pull earth with bucket when the machine travels.
(1) Push dozer blade backward to fill and level
road.
(2) Apply boom, arm, and bucket.
As figure, curl bucket and place arm on little
front of vertical position.
Operate arm in while lift boom slowly. Once arm
pass the vertical position, lower boom slowly and
keep the plane movement of bucket.
Operating boom, arm, and bucket at the same time
enable the leveling operation more accurate.
Prevent collapse
Operation tips
In digging work, don’t allow bucket colliding with Wrong
crawler.
Try your best to place the excavator on horizontal
ground.
Don’t operate bucket as hammer or piling machine.
Don’t slew machine to remove blocks or break up wall.
Wrong
【Important】:
Don’t try to extend arm fully and drop bucket,
penetrate ground with bucket teeth to dig up rocks.
These will cause serious damage of machine.
Once trench excavated, it can dig up rocks by
raise bucket from earth.
Don’t make bucket bearing side load. For
example, don’t level materials by swinging bucket or
38
Operator’s Manual SWE80/80H
39
Operator’s Manual SWE80/80H
Warning: It must follow all safety regulations when the machine lifts objects.
Don’t use damaged chain, wire rope, or cord in lifting work.
Don’t move the load suddenly, don’t move load
on the top of human beings, and don’t permit
everybody adjacent to the load.
Ensure everybody away from lifted or
tightwire-tied and on the ground load, until the
chocks support the load or the load has been
stably placed on the ground.
Fix superstructure, and make the traveling
motor on the rear.
Don’t connect sling/chain on the bucket teeth.
(1) Sling/chain should tightly bind the load
down, the workman should glove when
bind sling/chain.
(2) Connect sling/chain with bucket lifting
ring, curled bucket, and retracted arm.
(3) Before start, it should uniform the hand
signal with signalman.
(4) Acquaint with the positions of all workmen in the range of working area.
(5) Connect hand rigging on the load and ensure the people pulling hand rigging away
from load.
(6) Try to lift the load before normal operation.
● Park the machine beside the load.
● Connect the load on the machine.
a) Lift load to 50mm (2in) height to the ground.
b) Swing the load to one side.
c) Keeping load close with ground, move the load from the side of machine.
(7) Just lift the load to required height.
the hose end of hydraulic breaker to avoid dirt entering into system.
(2) Ensure stocking cover and plug in tool compartment for maintenance purpose.
(3) Avoid dirt entering into system when change the foreside attachment from bucket to
hydraulic breaker.
(4) After connection, check the oil leakage and bolts slack condition.
(5) Before fit hydraulic breaker on the arm, read manual books of machine and hydraulic
breaker carefully, and carry out the required Wrong
confirmation or inspection.
(6) Carry out required inspection before daily
operation.
(7) Operate machine slowly, the stability of
machine will be decreased because the hydraulic
breaker is heavier than the bucket. So, use dozer
blade to support and work in front of dozer
blade.
Wrong
Wrong
(8) Avoid hammering work with hydraulic breaker.
Never use boom or arm to break objects, otherwise
it will damage machine.
Wrong
Attention
41
Operator’s Manual SWE80/80H
Wrong
(14) Don’t lift objects with hydraulic breaker,
otherwise it will cause machine upset and (or)
breaker damage.
Note: (1) Number with ★ mark means the interval that all the machine operation time
is for hydraulic breaker. For the hydraulic breaker operation time ratio is less
than 100%, the replacement interval should be as hereinafter diagram shows.
(2) When the machine operates hydraulic breaker continuously more than 100
hours, replace hydraulic oil filter core.
1500hrs
lifetime
Hydraulic breaker hydraulic oil
operation time
percentage (%) Filter core
replacement
interval 2500hrs lifetime
hydraulic oil
42
Operator’s Manual SWE80/80H
Startup crusher
(1) Set the breaking/swing choosing
switch to the position of breaking.
(2) Put the head of crusher to the right
position, when tread on the left single
element pedal valve, crusher start to work. Release the left single element pedal valve
after finishing operation.
43
Operator’s Manual SWE80/80H
44
Operator’s Manual SWE80/80H
3. Operation
①.Refrigeration: After starting the engine, turn on the COOL switch, turn the air flow
switch to H position and run for 5 minutes, then switch the temperature-control to COOL
position. At this time, the air conditioning system begins to work and cab temperature begins to
drop.When reaching the desired temperature, rotate the temperature-control switch
counterclockwise until the compressor stops working. This will establish the desired indoor
temperature. When the cab temperature is higher than desired temperature, the indicator light is
bright and refrigeration will automatically resume. When cab temperature is lower than the
desired temperature, the indicator light goes off and the system stops working.
The fan control switch has three different speeds: high, medium, and low. Cabin vents can be
adjusted both vertically and horizontally to control the direction of air flow.
Notice:
a. Please do not turn the temperature-control switch to COOL position as well as turn the
air flow switch to the low speed while using air condition, in case that the evaporator forms
frost which influence the refrigeration effect.
b. Cold warm air conditioner: Please don’t turn on the hot water valve at the time of
refrigeration in summer.
②.Heating: To operate the heater in winter, close the temperature-control switch firstly.
After the engine is started, open the switch and choose HOT position. The hot water valve is
opened and the indoor temperature begins to rise. When the desired temperature is reached, the
45
Operator’s Manual SWE80/80H
air vent closes. When the temperature is lower than desired, the air vent will open again.
The fan control switch has three different speeds: high, medium and low. Cabin vents can be
adjusted both vertically and horizontally to control the direction of air flow.
Notice:
The heat source of the heating system adopts the engine cooling water, which is
communicates with water tank of the engine, when the environment temperature is lower than
0 degree centigrade and the engine does not work, you should empty the water tank of the
engine, or fill the anti-icing fluid in the water tank as not to freeze the heating system to crack
and heat the core body.
46
Operator’s Manual SWE80/80H
Transportation measurement
SWE80H
Overall height: 2622mm
Overall width: 2160mm
Overall length: 6497mm (arm and bucket cylinder fully extend and foreside attachment on the
trailer shelf)
SWE80
Overall height: 2622mm
Overall width: 2160mm
Overall length: 6740mm (arm and bucket cylinder fully extend and foreside attachment on the
trailer shelf)
Transportation on highway
Before transportation on highway, you should
know and follow all the related regulations.
(1) Check the length, width, height, and weight
of the trailer that load excavator.
(2) Check transportation route conditions, such as
dimension and weight limitations and traffic
rules.
Sometimes, it needs to separate excavator to smaller parts to satisfy the limitations of
dimension or weight.
47
Operator’s Manual SWE80/80H
(1) Before loading or unloading, clean the slope or loading platform and the carriage bed.
The slope, loading platform, and carriage bed with smear, earth, or ice have the danger
of slippage.
(2) Place chocks under the trailer head or wheels when use slope or loading platform to
load or unload.
(3) The slope should have enough width, length, and intensity. The obliquity of slope
should be less than 15° without fail.
(4) Loading platform must have plenty of width and intensity to support excavator, and the
gradient must be less than 15°.
Loading: 900~1100
[Note]: In cold weather, it should warm up the machine before loading or unloading.
48
Operator’s Manual SWE80/80H
Transportation
Warning: Tie the chain or thick rope on
the chassis frame, don’t traverse or press
the chain or thick rope on the hydraulic
pipe or hose.
(1) Place chocks at the front and rear of crawler
to fasten machine.
(2) Fasten the 4 corners and foreside attachment of machine on the trailer with chain or
thick rope.
Unloading
Warning:
(1) The machine should travel at lowest speed on slope.
(2) To avoid turning when move on slope,
if need turning, the machine should
return to the ground or trailer bed, 900~1100
Storage
Long-term storage of machine
While storing the machine, retract the cylinder piston rod to the inside of cylinder as much as
49
Operator’s Manual SWE80/80H
possible to avoid piston rod corrosion caused by rain and wind, clean machine surface and all
the exposed parts.
5. Maintenance
Fuel and lubrication chart:
50
Operator’s Manual SWE80/80H
【Important】
(1) Use recommended fuel, hydraulic oil, and lubricant.
(2) Only use original Sunward parts.
(3) If user doesn’t use recommended fuel, hydraulic oil, lubricant, and original Sunward parts,
the warranty is automatically invalid.
(4) Never adjust engine revs limiter or hydraulic system safety valve.
(5) Avoid electric parts touching with water and vapour.
(6) Never disassemble engine pump controller, sensor, etc.
Periodic maintenance
51
Operator’s Manual SWE80/80H
Engine maintenance
Please carry out periodic maintenance as per the engine manual book.
52
Operator’s Manual SWE80/80H
Replacement
Periodic replaced parts
Interval
Fuel hose (from fuel tank to precipitator, from precipitator to
Engine 1.5 years
oil feeding pump)
Pump inhaling hose (from oil tank to main pump) 2 years
Machin
Pump output hose (from pump output to multipurpose valve) 2 years
eBod
y Multipurpose valve hose (from multipurpose valve to working
2 years
device, slewing coupler, slewing motor)
Low pressure hose (pilot hose, oil-returning hose) 2 years
Boom cylinder hose 2 years
Workin
Dipper cylinder hose 2 years
g
Device Bucket cylinder hose 2 years
Note: Make sure to replace seals (such as O ring) when replace hoses.
53
Operator’s Manual SWE80/80H
○:Check
◇:Replace
★:means that the replacement intervals will be different with different working condition.
54
Operator’s Manual SWE80/80H
Interval (hours)
Parts name Qty 8 50 100 250 500 1000 2000
Connection pins for boom and ★
1 △
platform △
Connection pins for boom ★
2 △
cylinder ends △
Connecti ★
on pins of Pins for bucket and arm △
8 △
working ★
device ★
Pins for dozer blade cylinder
2 △
ends
Connection pins for dozer
2 △
blade and platform
Slewing support 1 △
Slewing inner gear ring 1 △
★★ means that these parts need maintaining when working in water or mud.
Recommended lubricative grease brand and specification
Position: bucket, dipper, boom, slewing gear, slewing bearing,
etc.
From —20 to 40°C(from —4 to 104F)
BP petroleum BP Energrease Ls—EP2
Caltex petroleum Multifax EP2
Esso Beacon EP2
Japan Daphne Coronex Grease EP2
Mobil petroleum Mobilux EP2
Germany 2# lithium grease ★
Shell Shell Alvania EP Grease 2
Remark Heavy duty lithium grease
[Note]:The delivered excavator from factory has been injected grease with
“★” mark.
Butter filling mark:
Interval(hrs)
Parts name Qty Remark
8 50 100 250 500 1000 2000
Check
Engine oil 1 △
oil level
Engine oil Replace 7.4L △★ △
Engine oil filter Replace 1 △
55
Operator’s Manual SWE80/80H
Note:★ means that you must replace oil in the first 50-hour operation of machine.
Please maintain as per the requirement in diesel engine manual.
z The performance of engine oil is very different, commonly the engine oil adopts API or
CCMC standard.
z YANMAR engine company recommends using SAE15W-40 engine oil of (API) CE4/SG
grade.
Fuchs 15W-40
Fina CF15W-40
Note: The excavator departed from factory has been filled with “★” marked engine oil.
56
Operator’s Manual SWE80/80H
Warning: The engine oil may be very hot, please be cautious of scalding.
(1) Take out outlet plug, make the oil flow into a 10L container through a piece of clean
cloth.
(2) After oil is vented, check whether there is metallic chipping on cloth or not.
(3) Fit and screw down outlet plug.
(4) Clean the surrounding area of engine oil filter seat. Turn anti-clockwise to remove engine
oil filter cartridge. Take out old seals.
(5) Clean sealed washer surface of filter seat.
(6) Wipe clean oil on the seals of new filter.
(7) Fit new filter, turn filter clockwise until the washer touches interface. Make sure not to
damage washer when fit filter.
(8) Screw down engine oil filter. Remember not to make it too tight to prevent screw thread
distortion or filter core seals damage.
(9) Open oil filter cover, and fill recommended oil into engine. 15 minutes later, check
whether the oil level lies in the marking range or not.
(10) Fit filler cap.
(11) Start engine, run at low rev for 5 minutes.
(12) Check whether the engine oil pressure indicator light goes out at once or not, if not,
stop engine and find out the cause.
(13) Stop engine, take out key from key switch.
(14) Check whether there is any leakage at outlet plug.
(15) Check oil level on the dipstick.
Interval (hours)
Parts name Qty
8 50 100 250 500 1000 2000
Check oil
— △
1、Slewing reducer level
Replace 2L △
Check oil
— △
2、Traveling reducer level
Replace 2x2 L △
57
Operator’s Manual SWE80/80H
Fina GL-580W-90
Note: The excavator departed from factory has been filled “★” marked gear oil.
1 Slewing reducer
Check oil level…every 250 hours operation
(1) Place the excavator on a horizontal ground.
(2) Lower bucket to ground.
(3) Run engine idle for 5 minutes. 1
(4) Shut off engine, and take out key switch.
(5) Pull the pilot control lever to lock position.
(6) Take out dipstick, the oil level must lies between
marks.
(7) Take out filler cover, and fill oil, if
necessary.
(8) Check oil level again.
In the sketch, ① is filler orifice, ② is oil
outlet.
2
Replace gear oil…every 1000 hours operation
Place the excavator on a horizontal ground.
Lower bucket to the ground.
Run engine at low revs for 5 minutes.
Shut off engine, and take out key switch.
Pull the pilot control lever to lock position.
58
Operator’s Manual SWE80/80H
Warning: the gear oil may be very hot, please remember to start work until the
gear oil cool down.
Take out oil outlet plug, empty gear oil.
Re-fit on oil outlet plug.
Take out filler cap. Fill in gear oil until the oil level to the mark of dipstick.
2 Traveling reducer
Check oil level…every 250 hours
(1) Place excavator on horizontal ground.
(2) Lower bucket to ground.
(3) Run engine at low revs for 5 minutes.
(4) Stop engine, and take out key switch.
(5) Pull pilot control lever to lock position.
(6) Open oil level inspection plug ②, check oil
level.
(7) Fill oil to figured oil level through filler ②, if
necessary.
In the figure, ② is reducer filler, ③ is oil outlet.
59
Operator’s Manual SWE80/80H
Interval (hours)
Parts name Qty
8 50 100 200 400 800 1500 2000
1Check hydraulic oil level —— △
Discharge sundries of hydraulic △
——
oil tank
Replace hydraulic oil 60L △
Clean oil inhaling filter —— △
Replace oil inhaling filter —— △
Clean oil returning filter △
Replace oil returning filter core. —— △
Replace pilot oil filter —— △ △
Leakage —— △ △
Check hose
and pipeline Crack and △
——
distortion
Note: The replacement interval will be different with various kinds of hydraulic oil.
Engine
oil -20℃--40℃ -10℃--40℃ -20℃--40℃ -10℃--40℃
Manufacturer
Fina HM46
Esso Standard Essolube D-3
40
10W 30
Mobil ★
Shell 1310
Caltex HD46
Shanghai oil refining
factory
Note Abrasion-resisted hydraulic oil
Note: The excavator departed from factory has been filled “★” marked hydraulic oil.
61
Operator’s Manual SWE80/80H
(14) Clean, fit on, and screw down oil outlet plug.
(15) Fit on cover 1, ensure filter and hanging rod on correct position, and screw bolts to
49N·m (5kgf·m).
(16) Unscrew cover of respiration orifice 2 on the top of hydraulic tank.
(17) Fill clean hydraulic oil to tank through filter netting. The oil level should reach the
scheduled marks of oil meter.
(18) Screw don cover of respiration orifice.
63
Operator’s Manual SWE80/80H
Hose
Interval (hours) Inspection point Abnormity Solution
Interval (hours)
Qt
Parts name 10 25 50
y 8 50 1000 2000
0 0 0
1. Vent fuel tank sediment 1 △
2. Check and vent sundries in precipitator 1 △※1 △
3. Vent water and sediment in water
1 △
segregator
4. Replace fuel filter 1 △
Fill oil
Warning: Dispose fuel carefully, it must stop
engine before fill fuel. Never smoking when
you fill fuel into tank or fuel system works.
(1)Refer to “stop engine” chapter, park excavator
and stop engine correctly.
(2)Check fuel display, and fill fuel if necessary.
(3)Prevent dirt, dust, water, and other sundries entering into fuel tank and fuel system.
(4)To prevent clogging, fill fuel after daily work, and not to splash fuel on excavator or
ground.
(5)Fit on the cover after fill fuel.
65
Operator’s Manual SWE80/80H
(2) Check whether fuel hose has distortion, attrition with other parts, and leakage. If any
abnormity occurs, replace the hose immediately.
(3) Repair or replace any slack or damaged hose. Never fit on flexural or damaged hose.
Hose
Note: Only use original parts from Hunan Sunward Intelligent Machinery Co., Ltd
Interval (hours)
Parts name Qty
8 50 100 250 500 1000 2000
Or indicator light comes
Clean 1 △
1.Outer filter core on
Replace 1 5 times clean or 1 year.
2.Inner filter core Replace 1 When outer parts replaced
3 . Connection Check
△
pipeline airproof
between air When pipeline has crack and air leakage,
Replace
filter and engine replace it in time.
check airproof and fixation termly of elastic joint between engine and air
filter.
(1) Park excavator on horizontal ground.
(2) Lower bucket to ground
(3) Run engine idle for 5 minutes.
(4) Stop engine, and take out key switch.
(5) Pull pilot control lever to lock position.
(6) Loosen wing nut to take out cover of air filter.
(7) Remove outer filter core.
(8) Flap outer core lightly, never beat it with hard objects to prevent damaging core.
(9) Clean outer core with compressed air. Remember to clean it from inside to outside.
Warning: Decrease pressure of compressed air, keep other people away from
operation site, beware of flying debris, and wear personal safety
implements.
(10) Clean filter inside before fit on outer core.
队 Warning: Wipe filter shell and sealed section with wet cloth, don’t clean them with
compressed air.
(11) Fit on outer core.
(12) Fit on end cover and screw wing nut down.
(13) Start engine and run at low revs.
(14) Check the air filter clogging indicator light on display. If the light comes on, stop
engine immediately and replace outer core.
(15) When change core of air filter, remember to change inner and outer core at one time.
First remove outer core, then remove inner core slowly. Clean filter inside before fit on
new core. Fit inner core first, then fit on outer core.
Note: It must underlay sealed washer when fit on core to avoid bad airproof.
Note: If bad airproof or crack occurred on connection pipeline, dirty air will enter into
and damage engine.
68
Operator’s Manual SWE80/80H
Interval (hours)
Parts name Qty 50
8 50 100 250 1000 2000
0
1. Check cooling water
1 △
level
2. Check and adjust fan
1 ※1 △
belt tension
3. Replace cooling water 20L Twice in a year ※2
4. Clean △※
radiator and Outer 1
3
hydraulic oil
cooler core Inner 1 When replace cooling water
5. Clean condensation
△※
device of air conditioner 1
3
(optional)
Warning:
(1) Antifreeze is poisonous, if ingested, will cause serious injury or death. In case
drink it by accident, should lead vomiting and go to hospital at once.
(2) Ensure storing the antifreeze with sealed cover and marked container, and the
antifreeze should be stored at the place that children can’t get.
(3) If the antifreeze splash into eyes by accident, wash the eyes 10 to 15 minutes with
69
Operator’s Manual SWE80/80H
the discharged water is clean. It can help to get rid of rust and sediment.
(4) Shut outlet plug, fill the radiator with tap water and antifreeze according to scheduled
ratio.Start engine to exhaust the air in cooling system
(5) To avoid air bubble entering into system, it should add cooling water at the rate of less
10L/min.
(6) After fill cooling water, run the engine for a few minutes. Then, check the cooling
water level again, fill cooling water again if necessary.
5.8 Others
Interval (hours)
Parts name Qty 8 50 100 250 500 1000 2000
1 . Check abrasion and
—— △
laxation of bucket teeth
2.Replace bucket 1 If necessary
3.Check crawler 2 △
4.Adjust crawler 2 If necessary
Correct Wrong
Note: Check the bucket teeth at regular interval to ensure the abrasion don’t exceed the
scheduled limitation.
2 Replace bucket
Warning: Prevent the injury caused by flying off metal scrap when beat the
connection rod in or out. Wear goggle or safety glass and other safety
instrument.
(1) Place the machine on the horizontal ground, lower the bucket to the ground and place
its plane surface on the ground. Ensure the
bucket won’t roll after remove pins. Connection rod
73
Operator’s Manual SWE80/80H
Dia. of Fastening
Item Installation position bolt Qty torque
mm Nm
Shock absorption anchor bolt of diesel
1 engine M12 4 103
3 Fitting bolts for hydraulic oil and fuel tank. M16 7 205
74
Operator’s Manual SWE80/80H
75
Operator’s Manual
SWE80/80H
Warning: Don’t connect the poles directly with metal objects to check the battery
deposit. It should use voltage meter or gravimeter to check.
Always take off earthing (一) battery clamp first, and fit on finally.
1040F 400C
680 200C
F Working range
0
0C
320F
0
-200C
-4 F
-400C
-400F
1.21 1.22 1.23 1.24 1.25 1.26 1.27
1.28 1.29 1.30 1.31 1.32
76
Operator’s Manual SWE80/80H
77
Operator’s Manual SWE80/80H
If the machine will be out of use for more than one month, it should carry out following
protective steps to ensure the performance of machine won’t be suffered during storage period.
Protective steps for extended period storage
Content
(1) You should not dismantle the whole air conditioner system. This will prevent the
refrigerant from letting out.
(2) After the first quarter of using it, check belt elasticity, if you find it is too loose, adjust
the tension degree or change belt in time.
(3) Wash condenser surface with compressed air or water regularly.
(4) Check air conditioner pipeline and line bunch regularly to prevent the pipeline and line
bunch from wear and tear, scald, excessive crook and loose connector.
78
Operator’s Manual SWE80/80H
(5) While changing the spare parts, add refrigeration oil by following the table below.
(6) Prevent tiny sand from entering the compressor clutch.
(7) Please don’t repair the air conditioner system by yourself. Please contact a professional
repairman.
79
Operator’s Manual SWE80/80H
6. Trouble shooting
If failure occurs, it must stop machine, and maintain the machine as following methods.
【Important】 : Important: Only authorized people can disassemble and repair the
hydraulic parts, please consult with manufacturer if mentioned works is
necessary.
Note: The diesel engine failure and its solution,please see the《YANMAR 4TNV98-SSU
engine manual book》.
Failures Causes Solutions
1. Hydraulic failure.
2. Air bubble in 1. Consult with your
Control levers don’t work hydraulic system. dealer.
3. Aging hydraulic oil, 2. Check whether air
or work slowly degenerative oil by leakage at oil pump
moisture, wrong brand inlet pipeline.
and specification 3. Replace oil.
hydraulic oil.
Noisy hydraulic pump and
4. Too low hydraulic oil 4. Warm up machine by
vibratory pipeline temperature and too
high viscidity of low revs engine run.
hydraulic oil.
1. The machine is out of
use for a long time, air
separate from oil and
float in pilot control 1. Operate control levers
pipeline and hydraulic for a few times.
cylinder. 2. Check hydraulic
2. No pressure or control system, low
Control levers don’t work exceeding pressure in pressure relief valve,
pilot system. and gear pump.
or work slowly. 3. Too low hydraulic oil 3. Warm up machine
temperature and too 4. Consult with your
high viscidity of dealer.
hydraulic oil 5. Consult with your
4. Hydraulic pump dealer.
failure.
5. Main safety relief
valve failure
1. Corresponding pilot
1. Repair
valve failure.
2. Corresponding 2. Consult with your
commutator valve dealer
failure
A cylinder doesn’t work or 3. Corresponding 3. Consult with your
dealer
work slowly. overload valve failure
4. Consult with your
4. Hydraulic cylinder
dealer
pole damaged
5. Replace seals
5. Hydraulic cylinder
inner seals damaged
Swing platform doesn’t 1.The pilot valve failure. 1.Repair
2.The swing retarder 2.Consult with your
slew or slew slowly or failure dealer
80
Operator’s Manual SWE80/80H
Abnormal sound, Air in the system or oil Pay attention usually and
dispose in time
vibration, and scent aging
1. Pilot valve failure
Slewing platform doesn’t 2. Hydraulic motor 1. Repair.
failure 2. Consult with your
slew, slew slowly, or slew 3. Slewing reducer dealer
failure 3. Consult with your
unsteadily. 4. Slewing support dealer
failure 4. Check and repair.
5. Lack of grease in 5. Fill in grease.
slewing bearing
81
Operator’s Manual SWE80/80H
Air- conditioner
Malfunction Phenomenon Check Solution
The air Air-flow is ok but Electromagnetic
conditioner the compressor clutch defect
system does not does not run Electric wire circuit Examine and repair
refrigerate or broken
work Imperfect earth Examine and repair
connection
Coil broken or Replace
damaged
Lower voltage of Adjust the voltage
compressor
Clutch skids Replacing
The electromagnetic
clutch is normal
The driving belt of Replace or adjust
the compressor
ruptures or is too
loose
Compressor defect Replace
Air-flow is ok and Refrigerant runs out Examine and repair
the compressor run The pipeline stops up Repair
Valve or the Repair or replacing
component damaged
No air-flow Electric wire broken Examine and repair
or connecting
component loose
Imperfect earth Examine and repair
connection
Air-flow switch Examine and replace
damaged
Change-speed Replacing
resistance damaged
Defective Evaporation air Little refrigerant Add refrigerant
refrigeration blower and Reverse connection Examine and repair
performance condensation air of liquid reservoir
blower work input and output
normally Expand valve Examine and repair
stopped up by ice any
other materials
Dirt covers the Wash the condenser
condenser surface several times
82
Operator’s Manual SWE80/80H
7. Specifications
7.1 Position of the various machine components
83
Operator’s Manual SWE80/80H
7.2 Dimension
84
Operator’s Manual SWE80/80H
85
Operator’s Manual SWE80/80H
Hydraulic system
Hydraulicpump…………………………………………………………… 2 variable axile
plunger pump+1 gear pump
Model……………………………………………………………………… PSVD2-27E-12
Displacement………………………………………………………………2x26.9+19.2+4.9mL/rev
Work pressure………………………………………………………………… 25MPa
Multitandem valve……………………………………………………………… KVSE-72-11
Model………………………………………………………………………MAG-33VP-550F-3
Hydraulic oil tank………………………………………………………………Capacity 110L
Hydraulic cooling device
Oil cooling device model………………………………………………………………… B878
86
Operator’s Manual SWE80/80H
Swing mechanism
Speed ratio……………………………………………………………………………… 22.7
Max. output screw moment………………………………………………………… 1841N.m
Platform rev…………………………………………………………………………10 r/min
Slewing bearing and name……………………………………………………… Single row
Swing brake………………………………………………………………………… hydraulic
brake “+”spring
pressure multiple
brake (normally
closed)
Electric device
Battery…………………………………………………………………………… 1×12V,63Ah
Starter…………………………………………………………………………… 12V,1.7kW
Generator…………………………………………………………………………… 12V,40A
Fuel device
Fuel tank capacity……………………………………………………………………… 110L
Travel mechanism
Speed ratio……………………………………………………………………………… 47.4
Maximum output torque moment
High speed…………………………………………………………………… 4141N.m
Low speed……………………………………………………………………… 6243N.m
Travel speed
High speed……………………………………………………………………… 0~5km/h
Low speed…………………………………………………………………… 0~2.8km/h
Gradeability………………………………………………………………………… 30°
Travel brake…………………………………………………………………hydraulic brake“+”
spring pressure
multiple brake
(normally closed)
Track tension……………………………………………………………………… hydraulic
87
Operator’s Manual SWE80/80H
88
Operator’s Manual SWE80/80H
SWE80/80H is an all hydraulic track excavator with beautiful appearance, 360° rotatable flat
roof, 1590mm long small rear end, all of these ensure the work in limited place.
The engine is Cummins 4 cylinder water-cooling diesel engine which has a normal rated power
of 45kW/2800rpm. We use flexible supporting breadthwise and install engine at the rear end of
machine.
Engine inlet channel is equipped with safety components which makes work more reliable.
Large capacity water tank with air exhaust device for the engine cooling system can effectively
protect engine and ensure normal work in high temperature and prevent overheating.
Full power constant flow main pump and engine directly connected with flange, maximum
work pressure is 28 Mpa.
Use flexible shaft coupling installed in the diesel motor flywheel to drive the main pump,
perfectly avoid the influence on main pump, which is caused by the vibration of diesel motor.
We use foreign products for hydraulic pump, main pump, travel motor and swing motor which
have good quality, work stably and guarantee reliable operation of the whole system.
Fuel device
89
Operator’s Manual SWE80/80H
Diesel tank can be supplied from a 110L fuel tank, the compact and appropriate design makes
it very easy to add fuel and clean.
Slewing drive
Hydraulic swing motor drives the swing supporting of inner joggle through a planetary reducer.
The normally engaged brake in drive system can ensure the safety of the machine.
Undercarriage
The excavator undercarriage is a high tortuosity rigid steel structure part.
The large dimension pilot wheel and drive wheel provide best travel ability on severe road
condition and self-clean ability.
The wheels and track is Jin Jiang and Shan Tui products with high stability and quality. The
single element of track device, such as oriented wheel, carrier roller, track wheel, have a long
lubricant cycle and don’t need to be maintained frequently.
Hydraulic track tension device can conveniently tension and loosen track.
The helix spring provides huge tension power for oriented wheel and ensures the track
orientation, avoid track digression.
High alloy steel track has good adhesion, stability and long service life.
Travel drive
We use axial piston double speed oil motor for power supply, providing high travel speed and
more traction.
Novel travel mechanism is a build-in structure with compact structure and high universality.
For we adopt the vairable system, the traveling speed varies from 0~2.8 km/h to 0~5km/h.
Travel brake
We use Japanese KYB plug-in plunger motor and well-assorted brake drive and hydraulic
brake“+”multiple spring pressure brake (normally closed) to provide stable brake ability while
working, especially when working on the slope.
Compensation valve connected with travel motor can avoid overdrive when machine traveling
on slope.
Cabin
The elastically installed cabin tallies with international standard on width,height and structure.
In addition, the test result according to the ISO10262 and ISO12117 standard of cabin protection
structures by the engineering equipment lab center of Ji Lin University shows that the prototype
meets the lowest performance requirements.
Wide front door can extend to the front and ensure convenient passage.
Glass around the cabin and turnover front window provides best view for operator.
90
Operator’s Manual SWE80/80H
Cabin seat is designed according to the ergonomics and can provide more comfort. The surface,
backrest and rigidity are adjustable and can suit different kinds of requirement from different
operators.
Seat with safety belt and pillow is optional.
Control lever is appropriately integrated with left & right control box, the light handle of the
lever can prevent fatigue caused by long time work.
Double action pedal switch control the travel drive. Also it can be controlled manually.
Monitor is within operator’s sight and it is very easy to recognize the indicators on it, such as
engine, electronic device and hydraulic system. All the indicator’s sketch maps comply with
SAE certification.
There is radio installed in cabin.
Also, there is an air conditioner in cabin. The air conditioner we adopt is world famous Pu Fa
product from Liu Zhou with perfect performance.
Arm teeth
We adopt knockdown tooth, which has a tooth cover and tooth holder made by wearable alloy
steel. The cover and holder are connected with lateral pin, which allows easy replacement.
Though there is no special bucket tooth on the side of the bucket, there are side blades with
clearance angle to help digging.
91
Operator’s Manual SWE80/80H
92
Operator’s Manual SWE80/80H
8. Attachment
8.1 Electric System
93
Operator’s Manual SWE80/80H
94
Operator’s Manual SWE80/80H
95
Operator’s Manual SWE80/80H
96
Operator’s Manual SWE80/80H
9. About manufacturer
Trade mark:
Address: 16 LiXiang Road, Xingsha economic and technologic development district, Changsha,
Hunan.
About distributor
About distributor
Distributor name:
Address:
Tel:
Fax:
Email:
Service personnel:
Note
97