Professional Documents
Culture Documents
TC-575173-01-1
SCHEDULED MAINTENANCE TASK CARD
REV.DATE 2016-2-28
OUTER WING BOTTOM SKIN -DETAILED INSPECTION OF OUTER WING BOTTOM SKIN LOWER
SUBJECT SURFACE AT ATTACHMENTS TO MLG SUPPORT RIB 5
Comments:
A、 References
Reference Title
EASA AD2015-0026R1 Wings – Wing Bottom Skin at Main Landing Gear Rib 5 –
Inspection
C、Tool Equipment
Reference Description QTY
N/A
D、Consumable Material
Reference Description Specification
08BAA9 Cleaner
E、Feedback
□ Need to feedback: After this task card be implemented, please feedback page
to system engineer of Engineering Department if required.
Mechanic/Date Inspector/Date
HA-ME-F-137 PAGE 1 of 6
NO. TC-575173-01-1
SCHEDULED MAINTENANCE TASK CARD
REV.DATE 2016-2-28
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL
THE CAUTIONS INCLUDED IN THE REFERENCED PROCEDURES.
NOTE: The items given in this note shall be considered as the basic
Aircraft
configuration before you start a maintenance task:
HA-ME-F-137 PAGE 2 of 6
NO. TC-575173-01-1
SCHEDULED MAINTENANCE TASK CARD
REV.DATE 2016-2-28
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-869-002.
(b) Make sure that the ground safety locks are in position on the MLG,
refer to AMM Task 32-00-00-481-001.
(c) Open the MLG doors, refer to AMM Task 32-12-00-010-001.
(d) Put the access platforms in position at zones 571, 574, 671 and 674.
2 PROCEDURE
NOTE: All Taper-Lok fasteners (9/16 in. and 5/8 in.) must be visually
inspected to reduce risk of confusion and missed inspections of the affected
9/16 in. fasteners.
(a)At the inboard internal surface of gear rib 5 web,refer to Fig. A-UCAAA
Sheet 01, inspect for missing/migrated fasteners and/or missing nuts/tails.
(b) If no fasteners are missing or migrated and no nuts/tails are missing:
- Complete the Inspection Report Sheets with all findings, including nil
findings per Fig. A-URAAA Sheet 01
- Go to step 3.
(c) If fastener missing or migrated or nuts/tail missing is found,report to
related structure engineer.
Inspection Result:
(2) Do a Detailed Inspection (DET) of the Fasteners at the Inboard Internal RII
Surface of the Gear Rib 5,RH Wing
HA-ME-F-137 PAGE 3 of 6
NO. TC-575173-01-1
SCHEDULED MAINTENANCE TASK CARD
REV.DATE 2016-2-28
Inspection Result:
3
CLOSE-UP
(1) Close-Up
(a) If necessary, install access panels 574AB (674AB), refer to AMM Task
57-51-37-400-008.
(b) Make sure that the work areas are clean and clear of tools and other
items of equipment.
(c)Remove the ground safety locks from the MLG, refer to AMM
Task32-00-00-081-001.
(d) Remove the access platforms.
(e) Close the MLG doors, refer to AMM Task 32-12-00-410-001.
(f)Put the aircraft back to its initial configuration.
HA-ME-F-137 PAGE 4 of 6
NO. TC-575173-01-1
SCHEDULED MAINTENANCE TASK CARD
REV.DATE 2016-2-28
Appendix Figure
HA-ME-F-137 PAGE 5 of 6
NO. TC-575173-01-1
SCHEDULED MAINTENANCE TASK CARD
REV.DATE 2016-2-28
HA-ME-F-137 PAGE 6 of 6