Professional Documents
Culture Documents
3 Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil cum 35612.86
containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and
rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of
the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of
foundation etc on solidating each deposited layer by ramming and watering and then disposing
of all surplus soil as directed within a lead of 50m.
4 Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and cum 28469.87
watering etc. complete.
5 Extra for every additional lift of 1.50 m or part thereof for earth work in all soils including shingles, cum 9688.14
small size boulders upto 30 cm size but excluding saturated soil and rock.
(From 1.5 to 3.0 m)
6 (From 4.5 to 6.0 m) cum 9688.14
7 (From 4.5 to 6.0 m) cum 16268.88
8 Extra for every additional lift or 1.50 m or part thereof for decomposed soft or hard rock. cum 9688.14
(From 1.5 to 3.0 m)
15 Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 sqm 314.48
stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal
size well rammed and consolidated and grouted with fine sand including finishing the top smooth.
[1/80]
Page - 2
Bill of Quantities (BoQ)
29 All works above plinth level upto floor V level cum 6189.25
30 Providing and fixing of expansion joint system related with floor location as per drawings and metre 328.60
direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members,
self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The
system shall be such that it provides floor to floor /floor to wall expansion control system for
various vertical locations in load application areas that accommodates multi directional seismic
movement without stress to it's components. System shall consist of metal profiles with a
universal aluminum base member designed to accommodate various project conditions and
finish floor treatments. The cover plate shall be designed of width and thickness required to
satisfy projects movement and loading requirements and secured to base members by utilizing
manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all
directions.
The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all
directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint
System to have watertight joint is mandatory requirement all as per the manufactures design and
as approved by Engineer -in-Charge. (Material shall conform to ASTM 6063).
Floor Joint of 100 mm gap
31 Providing and fixing of expansion joint system related with wall joint (internal/external) location as metre 83.60
per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum
base members, self aligning / centering arrangement and support plates as per ASTM B221- 02.
The material shall be such that it provides an Expansion Joints System suitable for vertical wall
to wall/ wall to corner application, both new and existing construction in office Buildings &
complexes with no slipping down tendency amongst the components of the Joint System. The
Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum
surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall
conform to ASTM 6063.)
Wall Joint of 100 mm gap
32 Providing and fixing of expansion joint system of approved make and manufacture for various metre 82.15
roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be
of extruded aluminum base members with, self aligning and self centering arrangement support
plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof
/roof to corner joint cover expansion control system that is capable of accommodating
multidirectional seismic movement without stress to its components. System shall consist of
metal profile that incorporates a universal aluminum base member designed to accommodate
various project conditions and roof treatments. The cover plate shall be designed of width and
thickness required to satisfy movement and loading requirements and secured to base members
by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves
in all directions.
The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all
directions including vertical displacement. The Joint System shall resists damage or deterioration
from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic
from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to
have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.)
Roof Joint of 100 mm gap
33 Providing & Fixing of GRC Panels Casted with Power Spray Concrete Mix Design all complete Sqm 532.62
as per architectural drawings under the direction of engineer in charge
34 Providing & Fixing of GRC Panels Casted Mouildings with Power Spray Concrete Mix Design all Meter 641.89
complete as per architectural drawings under the direction of engineer in charge
35 SUB HEAD-3A :- STONE WORK cum 141.40
Coursed rubble masonry (second sort) with hard stone in foundation & plinth with :
Cement mortar 1:6 (1 cement : 6 coarse sand)
36 Coursed rubble masonry with hard stone (first or second sort) in superstructure above plinth level cum 232.19
and upto floor five level.
Masonry work (second sort), in cement mortar 1:6 (1 cement: 6 coarse sand)
37 Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): sqm 2321.88
Flush / Ruled/ Struck or weathered pointing
[2/80]
Page - 3
Bill of Quantities (BoQ)
43 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and metre 141.62
drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.
44 Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen each 100
platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary
holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
49 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- sqm 640.02
decorative type, core of block board construction with frame of 1st class hard wood and well
matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on
both faces of shutters:
35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
50 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges sqm 640.02
of flush door shutters (over all area of door shutter to be measured).
51 Providing and fixing wooden moulded beading to door and window frames with iron screws, metre 1341.35
plugs and priming coat on unexposed surface etc. complete :
2nd class teak wood
50 x 20 mm
52 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ sqm 640.02
suede finish with high density protective surface layer and reverse side of adhesive bonding
quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
1.0 mm thick.
53 Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI sqm 640.02
marked flush door shutters conforming to IS: 2202 (Part I)
On one side only
54 Providing and fixing Single Glazing 6mm thick toughened glass from Gujrat Guardian Limited or sqm 1595.69
equivalent complete in all respects as per direction of the Engineer-in-charge. (Required
properties Solar factor ≤ 0.45, U-Value ≤ (W/sq.m-K) 5.7W /M2K, Visible light transmittance ≥
0.30)
55 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and sqm 21.12
manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement
and making necessary holes etc. for fixing required door fittings, all complete as per direction of
Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
56 Providing and fixing 12 mm thick frameless toughened glass partitions of approved brand and sqm 74.59
manufacturer, including providing and fixing partitions at top & bottom with aluminum channel
etc. all complete as per direction of Engineer-in-charge
[3/80]
Page - 4
Bill of Quantities (BoQ)
60 Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock Nos 70
on back side of the Panic Latch of reputed brand and manufacture to be approved by the
Engineer- in- charge, all complete.
61 Providing and fixing approved brand and manufacturer SS 304 grade hardware's for Doors etc. each 530
Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type fixed with SS
screws etc. complete in all respects as per manufacturers' specifications & as directed by
Engineer-in-charge.
62 Providing and fixing approved brand and manufacture SS 304 grade SS 304 grade Mortice lock each 232
with key cylinder fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
63 Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 250mm long each 40
with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
64 Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 150mm long each 200
with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
65 Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer each 265
fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as
directed by Engineer-in-charge.
66 Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door each 265
mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
67 Providing and fixing approved brand and manufacture SS 304 grade Top & Bottom Patch fixed each 24
with SS screws etc. complete in all respects as per manufacturers' specifications & as directed
by Engineer-in-charge.
68 Providing and fixing approved brand and manufacture SS 304 grade D type 1200mm Pull Handle pair 4
with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
69 Providing and fixing approved brand and manufacture SS 304 grade D type 300mm Pull Handle pair 8
with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers'
specifications & as directed by Engineer-in-charge.
70 Providing and fixing approved brand and manufacture SS 304 grade Glass to Glass Lock Round each 6
type with SS screws etc. complete in all respects as per manufacturers' specifications & as
directed by Engineer-in-charge.
71 SUB HEAD-VII:- STEEL WORK Kg 51699.12
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position
and applying a priming coat of approved steel primer using structural steel etc. as required.
In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
[4/80]
Page - 5
Bill of Quantities (BoQ)
76 Providing and fixing top cover for rolling shutters. metre 5.00
77 Providing and fixing ball bearing for rolling shutters. metre 15.00
78 Providing and fixing 12 mm thick and 100 mm wide pelmet with 25 mm dia wooden curtain rod Mtr 759.43
and brackets including fixing with 25 x 3 mm MS flat 10 cm long and plugs etc complete.
Timber class - A IV
79 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates kg 8268.51
etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and
fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with
necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required
size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of
Engineer-incharge, (for payment purpose only weight of stainless steel members shall be
considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
80 Supply and fixing of STRAIGHT PROFILED KALZIP or equivalent “SELF SUPPORTED” Sqm 6041.49
SECRET FIX STANDING ROOFING SYSTEM IN 0.9mm THICK AA 3004 ALUMINIUM ALLOY.
The general roof-construction shall comprise of:
Top layer – Kalzip 65-50/400-429 profiled sheet manufactured or equivalent from aluminium self
supported standing seam roof system manufactured from aluminium alloy AA 3004 (AlMn1Mg1)
as specified in BS EN 1396: 2007 minimum material thickness of 0.9 mm and Fluorocarbon
PVDF/Stucco finish on the exposed surface.
The material properties shall be as follows:
Ultimate tensile strength: minimum 200 N/mm2, 0.2% Proof Stress: min 185 N/mm2,
Modulus of elasticity: 70,000 N/mm2.
Including Accessories, aluminium ST clips and Fasteners.
Sheets are to be laid to meet the requirements of the building geometry and fixed on Aluminum
clips. Clip to be fixed to the top hat/purlins with SS 304 screws only.
Under Deck Insulation
Liner – Kalzip 35/200 Bare or equivalent Galvalume steel liner, 0.5 mm tct, 35 mm deep ribs
spanning up to 1500mm centres (multiple spans)
Vapour Control layer - A single layer of double sided aluminium foil vapour barrier.
Insulation - Rockwool insulation of 100mm thickness minimum 48kg/m3 density with thermal
conductivity of min K=0.04 W/mk at 25 degree Celsius. Fire classification with test procedures to
BS 476: Parts 6 & 7.
Flashings manufactured from aluminium alloy AA 3004 (AlMn1Mg1) as specified in BS EN
1396: 2007 minimum material thickness of 0.9 mm and Fluorocarbon PVDF/Stucco finish on the
exposed surface. The roofing system shall be certified with a British Board of Agreement
Certificate No 98/3481 plus the Institute of Bautechnic Zulassung beschield N R -14.1 .181
All installation is to be carried out by approved trained roofing installer. The installation team shall
be fully trained and approved by the manufacturer.
The roof system manufacturer/supplier must have a registered office in India The approved
roofing system manufacturer should have at least completed 150 projects of aluminium standing
seam roofing system in India with one project having area more than 150,000 m2.
Aluminium gutter of 2mm thickness with aluminium gutter expansion joints @ 12m.
all complete as per direction of Engineer-in-charge.
81 Designing, providing, installing/fixing skylight consisting of 16mm thick multiwall polycarbonate Sqm 494.62
sheet in approved color (minimum 900mm wide) with standing seam on both sides & double
tooth snap on locking system to ensure maximum uplift capability. The panel shall be co-
extruded UV protected and antiglare/soft light to prevent glare/sun streak . The cross section of
one cell should not be more than 4mmX4mm & weight of single panel shall not be less than 3250
per square metre. The system shall be fitted on purlins with spacing as specified by manufacturer
with stainless steel fastener & screws and supported on MS tube framework, complete as per
specification, drawing and direction of Engineer in Charge. The rate includes cost of all the
operations, labour materials and tests (as applicable) for proper completion of the work except
the M.S tubular framework which shall be measured and paid separately (For payment purpose
the area of finished polycarbonate sheet fixed in position shall only be measured).
[5/80]
Page - 6
Bill of Quantities (BoQ)
87 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), sqm 2349.13
with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all
colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement:
3 coarse sand), including grouting the joint with white cement & matching pigments etc.
complete.
Size of Tile 800x800 mm
88 Providing and laying Laminate wooden flooring (Grade AC4, 8 mm thick Ambience Premium- sqm 453.51
AC4 ), having a good backing layer made up of plastic laminate or melamine as specified by the
manufacturer and approved by Engineer-in-charge.
Flooring
89 Skirting sqm 45.35
90 Floor strip on edges Meter 22.68
91 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as sqm 5575.86
well as curvilinear portions of the building, all complete as per the architectural drawings, with 18
mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse
sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with
pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified
and as directed by the Engineer-in-Charge.
Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
92 Extra for Shot blasted finish sqm 2230.34
93 38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of sqm 253.12
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal
size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25(blown type)
@ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up
to half depth, planed, levelled smooth and finished complete.
94 Providing and fixing Vinyl flooring of 2mm thick PVC flexible, homogeneous antistatic calendared sqm 13.90
compacted floor covering, minimum weight 3120 g/m2 in minimum sheet of size 2mtrs. x 20
mtrs. approved pattern & colour combination with PUR Protect or equivalent surface treatment
having wear minimum resistance of ≤ 4.0mm3 as per EN 660.2 and wear group P as per EN-
649 and should have a minimum residual indentation of <0.03mm confirming to EN-433. The laid
flooring should have non- directional design, colour dyed as a raw mixture to ensure even colour
throughout the thickness and its surface should be densely compacted for improving wear and
ease of maintenance with Anti-bacterial and Fungicidal properties. The laid flooring shall
confirms the fire rating B1 class as per EN 13501-1. The floor finish should terminate at the room
perimeter passing over a concealed cove former and continuing up the wall for 100mm. The
joints in the flooring should be sealed by using a PVC welding bar of matching colour to be
supplied by the manufacturer, using a hot air gun for fusion of welding bar with flooring and self
levelling required underneath with all accessories cove etc.
95 Extra for pre finished nosing to treads of steps of Granite stone. metre 1429.68
96 Extra for Granite stone flooring in treads of steps and risers using single length up to 2.00 metre . sqm 221.61
97 Providing and fixing Ist quality ceramic glazed wall tiles of size 300x450 mm conforming to IS: sqm 1401.92
15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades
as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed
of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg
per sqm, including pointing in white cement mixed with pigment of matching shade complete.
[6/80]
Page - 7
Bill of Quantities (BoQ)
99 Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in Each 13841
stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the
necessary chases.
100 Toilet Cubical sqm 325.34
Providing and fixing Toilet Cubicle (of following standard dimension which includes 600 mm door
size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant
12 mm thick solid compact laminate panels Finish of the compact laminate should be raw silk
which include doors, pilasters and intermediate panels finished with approved texture/shade as
per the detail drawing and as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97
standard.
This also includes providing and fixing in position necessary hardware made out of Stainless
Steel (Grade 316) as per manufacturer's specifications and EIC instructions like (1) Door Knob,
(2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U- Channels, (6) SS-
Shoe Box Plate, (7) MS-Base Plate, (8) Rubber noise deafening tape, (9) Screws and wall Plugs.
101 Providing and fixing 40mm thick cladding comprising of Wooden framework using 25mx50mm sqm 1401.51
sections at a maximum spacing of 600mm in any one direction (including adding members as
required) covered with12mm thick BWP ply layered with 4mm thk. veneer (Basic Rate Rs.60/-
sqft)on one side pasted and pressed with adhesive to give a uniform and smooth finish,
including 4mm thk. S.S. strip framework on all sides of veneer panels with wooden member
surround, top moldings / margins, melamine polish etc. to finish the thickness, as shown
complete in drawing. All members / ply etc. shall be treated with anti-termite solution as per
norms. No extra shall be paid for making of openings, door / window frames and for making
provisions for electric conduits.
102 Providing and fixing of 6mm thick lacquer glass SGG Planilaque glass of approved color by sqm 53.99
architect/ Client with SGG Planifix silicon on perfectly leveled water proof non-conventional
plywood (preferably marine plywood) of minimum 12mm thickness mounted on the RCC wall/any
other structure. The SGG Planilaque lacquered glass to be of 6mm thick highly durable, humid
resistance, poly urethane lacquer glass. The Planilaque glass should be manufactured by
industrial curtain coating process. It should meet quality standards as per BS EN 1036 1999 &
confirms to PERSOZ hardness test of at least 220 oscillations. The substrate of the glass should
conform to Standard BS EN 572 1995 parts 1 and 2: Glass in Building – Basic soda lime silicate
glass products. Planilaque lacquered glass to be manufactured to right specifications, relating to
consistency of color, opacity and homogeneity throughout production campaigns and also to the
ageing properties, mechanical resistance, and resistance to humidity and to chemical agents of
the lacquer. The color of the lacquer should remain stable when exposed to normal levels of ultra-
violet light in interior applications.
103 Providing and fixing partition up to ceiling height consisting of GI frame work made of special sqm 1613.94
section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side
inclusive), consisting of floor and ceiling channel of 0.5 to 0.55 mm Metal Thickness ,72mm wide
& having two flanges of 30mm each to the RCC Floor and Slab with Approved Fastener @600
mm C/C respectively. The wall studs 0.5 to 0.55 mm Metal Thickness, 70mm wide having one
flange of 34mm another of 36 mm). These Wall studs are placed maximum distance of 610mm
C/C in Floor and Ceiling channel. 50mm thick @ 48kg/cum density mineral wool Insulation to be
suspended on Insulation Holder Strip positioned at 1200mm vertical centers within the stud
cavity. One layer of 15 mm thick Firebloc Plasterboard on Both side is screw fixed to metal
system using Self tapping 3.5 x 25 mm corrosion resistant drywall screws spaced at 150mm
centers on all joints and 300 mm centers in the field of plasterboards. Screw fixing is done
mechanically. Install Fixing Channel of 99mm x 0.90mm behind horizontal board joints and also
shall be fixed 1.2m above the FFL. Finally, plasterboards and screw heads are to be jointed and
finished to have a flush look which includes filling of tapered edge and square edges of board
with Redi mix all purpose jointing compound, Paper Tape. (As per recommended practice of
manufacturer). All perimeters and penetrations to be sealed with fire and acoustic sealant along
with baker rod as per manufacturer’s specifications.
[7/80]
Page - 8
Bill of Quantities (BoQ)
105 Providing & Fixing of Ceiling tiles shall be of high acoustic performance of Decosonic CNBM sqm 557.42
make and micro edge glass fiber in size 600x600x15 mm of color white/Black. It comprises a
high-density glass wool panel covered with painted glass wool tissue for decorative ceiling effect
and glass wool tissue on the backside and having sealed edges. It shall have a noise reduction
co-efficient of greater than 0.90, light reflection of over 85%, density of 100kg/m3, humidity
resistance. To lay the field panel of size 600x1200mm, flush fitting 1200mm long cross tees to be
interlocked between main runners at 600mm centre. Thus a grid system of 600mm X 1200mm
is formed. Installation shall not begin until all wet work is completed and dry. Building shall be
properly enclosed and under standard occupancy conditions (temperature of 20‐40°C and not
more than 70% relative humidity) before installation begins.
106 P/F STRETCHED FABRIC ACOUSTIC PANELS using: sqm 629.11
• GI frame work of 48mm GI Studs, 50 mm foor using 0.55mm thick and stud channels at
610mm x 610mm, 0.5mm thick, fixed with MS angle cleats 1220x610mm centers to wall by using
metal fasteners, backed with 22 SWG x 12.5mm GI Chicken Wire Mesh with air gap a minimum
of 50mm on back side, as per detailed drawing.
• The frame work to be filled with glass wool of 50mm thick of 48 kg/cum Cu. (Owens Corning)
laminated with Black FRP Tissue on the outer side, and chicken wire mesh support on the rear
side abuting the wall face.
The entire glass wool surface to be covered with 12mm thick FR ply, with 8mm diameter drilled
perforations at 25mm c/c in both directions.
Finished in stretched fabric finish, using UPVC grippers (Waltract/ Cineview ) fixed to 50mm x
12.5mm commercial plywood runners. The fabric should be inherintly fire-retardancy.
107 STAGE FLOORING: Providing and fixing 75x25 mm teakwood plank (1500mm long) flooring Sqm 270.00
with tongue and groove joints (concealed screwing and minimum length 1.5m) on two layers of
12mm thick water proof marine ply, plywood bonded with phenolic resin with half headless GI
nails/steel screws wherever necessary, with joints staggered with 2nd layer glued and screwed
to the first, fixed with wooden screws to teakwood joists framework comprising 75x50mm
teakwood joist 900mm centre to centre in one direction and 50x50mm teak wood battens 400mm
centre to centre on other direction, teakwood joists resiliently supported on 150 x 150mm pads of
7.5mm nominal thickness of waffle, neoprene pad ribbed (50 p.s.i. grade) and 50x50x6mm thick
MS angle cleat fixed with 150mm long with 10mm dia. GI bolts and expansion fasteners, over
floor slab 900x900 centre to centre, support locations including providing and applying a coat of
ready mixed aluminum primer and a coat of synthetic enamel paint both of approved brand and
manufacturer over exposed surfaces and edges of marine ply. Entire work to be done complete
as per drawings, specifications and direction of Engineer-in-Charge including wax polishing of
teak wood planks after filling wood filler and sand papering up to smooth finish in natural color.
Stage Floor - Moulding : Providing and fixing 145x50mm teakwood moulding as per architect on
the edges of stage wooden flooring including wax polishing of teak wood planks after filling wood
filler and sand papering up to smooth finish in natural color.
108 HALL FLOORING:- Providing & fixing of the cut pile designed carpet with 8mm profile underlay Sqm 1106.60
in the aisles and gangway. Complete with adhesive after rectification of the floor.
Specification of Carpet:
Construction - cut pile wilton weave
Fiber - 2 ply twisted yarn pp
Pile wt - 1100 grams / meter
Pile ht - 5 to 6mm
Color fastness - As per international standards
[8/80]
Page - 9
Bill of Quantities (BoQ)
110 Providing and supplying Armstrong ‘Optra Acoustical Wall Panelling’ with square edges made of Sqm 475.00
fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent
and fire-resistant fabric with an option of colours as per the choice of the Architect/ Person in-
charge of size 2100x600 or 1200x600 or 600x600 mm providing a minimum sound absorption
level of 0.90 NRC to be affixed to wall using Wall panel impalers supplied by M/s Armstrong
Industries India Pvt. Ltd and construction adhesives as per the instructions laid down by the
manufacturer. Installation: Armstrong wall panel impalers of adequate quantity as specified by
the manufacturer shall be fixed to the wall surface using self tapping screws. Silica based
construction adhesive shall be dabbed on to the projecting elements (spikes) of the impalers.
111 Acoustic Treatment for Stage both Sides & Back wall: Providing and fixing of magnesite Sqm 350.00
bonded woodwool panels made with superfine wood fibres & gypsum, were patented with
magnesite cement, edge profiles consist of Radius, Chamfer, Tongue-Groove & H-Spline
groove, having density 400kg/m3, Acoustic NRC upto 0.90, eco-friendly, Fire Ratings - Non-
combustibility At 750 oC, Thermal Resistance, Water Vapour Diffusion Resistant, size
600x600/1200/2400x25mm installed on Strut C-system requires unfastening and refastening of
fasteners . The Strut C-System framework consisting of CC10 Channels fixed at 600mm centres,
Long edges chamfer and kerfed for H-Spline; Thickness 38 mm installed on Strut C-system with
H-Spline.
112 Providing and fixing of 8 mm MDF board laser cut jali with design as per drawing to be fixed over Sqm 110.00
the frame work of 48mm GI Stud/ 50mm wooden battens. The framework to be supported on the
wall at a distance of 1800 mm centre to centre of size as reqd long 35x35x3mm angle cleats of
required length and MS anchor fasteners of size 65mm x10mm dia. The cleats to be given two
or more coats of red oxide primer. The entire work to be executed as per the drawings /
instructions of the Engineer-in-charge. The rate includes for all Geometry of wall, openings etc.
and for complete item including all the required approved material, labour and fixing as per
drawings enclosed. The work shall be executed as per specification , & instructions of engineer
in charge including cost duco paint of desired shade on the jali.
113 Providing and fixing 150 mm border out of 19 mm thick commercial block board of reputed make Rmt 200.00
like Century, Duro, Green with 1 mm laminate of reputed make like century, Greenlam as per
approved shade. of approved shade. To be fixed as per the drawings over a framework of 48mm
GI Stud of .55mm thk gypsteel @ 600c/c.. by means of 35x35x3MM MS angle hold fasts fixed
with anchor fasteners as per drgs...
114 Providing and fixing of Anutone Subtex Nubby Soft Fibre Square edge 15mm for Ceiling of size Sqm 400.00
595x595x15 mm is to be installed on framework of Anutone Skelet. Which will comprise of NRC
0.94 base panel with humidity resistance of 90% RH and light reflectance upto 85% with Leed
points Green Performance certified. Subtex Nubby Soft Fibre 15mm for Ceiling tile meet the
stringent fire test required having Class ‘A’ rating for Flame Ignitability test as per ASTM-E-84,
with complete framework of Anutone Skelet as per Installation details given
115 Installation Details:- Anutone Subtex Nubby Soft Fibre Square edge 15mm for Ceiling Tile is to Sqm 100.00
be layed on frame work of Anutone Skelet accessories pre-coated GI angle size 24x24x0.4 mm
thick fixed to the brick wall / partition at the perimeter of ceiling with Nylon Sleeves and APS
wafer head drywall screws, Then suspended main GI ‘T’ section (bottom precoated-White) with
polyester coating of 25 microns dry film thickness. Main T-section size 24x38x0.3 mm thick and
3600 mm long from soffit in one direction with the help of metal rawl plug, cleat, leveler,
perimeter & wall spring clip & G I Rod 4 mm diameter with galvanized spring steel level clip 1200
mm centres from soffit. G I cross T section (bottom precoated-White) size 24x25x0.3 mm and
1200mm & 600mm long is insert fixed into the slots provided as interlock in main ‘T’ at 600 mm
centres to form 600x600mm grid size for a tile size of 595x595 mm. All accessories such as
Anutone Skelet accessories cleat, suspenders, levelers, clips etc, shall be supplied and installed
in accordance with manufacturer recommendation.
Providing & fixing Ecco board acoustical panels of NRC 0.90 to be fixed over frame work of
48mm GI studs fixed on the wall. The framework to be filled with 50mm thick thermal bonded
non woven polyster wadding micron fiber of 1000 gm / sqm . The mikron fiber to be held in
position with chicken mesh of 18mm & 24SWG. The mikron fiber shall be of Mikasha
International/ Sandler.
116 Providing and fixing of False Ceiling with 1mm thick laminate to be fixed on 12mm ply over 2"x2" Sqm 300.00
softwood/40mm stud framework at 2'-0" c/c both ways. There will be other layer of 4mm thick ply
over 12mm ply to give necessary grooves as per drawing. The framework to be filled with 50mm
thick thermal bonded non woven polyster wadding micron fiber of 1000 gm / sqm . The mikron
fiber to be held in position with chicken mesh of 18mm & 24SWG. The mikron fiber shall be of
Mikasha International/ Sandler.
[9/80]
Page - 10
Bill of Quantities (BoQ)
118 Providing and fixing insulation above false ceiling with thermal bonded Polyester fibre 1000 gsm, Sqmt 1200.00
50mm thick confirming to 1S:8225 fixed in the spaces of frame and held in place with wire mesh
of 28Gx10 in front complete as per drawing & direction of Engineer-in-charge.
119 SUB HEAD-IX :- ROOFING meter 94.18
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone
aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine
sand) as per standard design :
In 75 x75 mm deep chase
120 Providing and fixing at all height false ceiling including providing and fixing of frame work made sqm 1550.30
of special sections power pressed from M.S. sheet and galvanised in accordance with zinc
coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm
thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling
with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of
25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts
to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the
ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having
clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I.
channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction
including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick
27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to
wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all
screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square
edges of the board with recommended filler, jointing tapes, finisher and two coats of primer
suitable for board as per manufactures specification and also including the cost of making
openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels
suitably fixed all complete as per drawing and specification and direction of the Engineer in
Charge but excluding the cost of painting with :
112.5 mm thick tapered edge gypsum moisture resistant board
121 Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true sqm 2325.45
horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (
galvanized @ 120 gsm/sqm, both side inclusive) consisting of main "T" runner with suitably
spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum)
sheet, spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm
thick (minimum) sheet, 1200mm long spaced between main "T" at 600mm center to center to
form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made
of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form
grids of 600x600mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of
approved texture in the grid including, wherever, required, cutting/making, opening for services
like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended
from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm fixed to ceiling with 12.5 mm
dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips
of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed
width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete at all
heights as per specifications drawings and as directed by Engineer-in-charge.
GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and
0.5mm thick with 8mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides
inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum),
including factory painted after bending.
122 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved sqm 1550.30
texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light
Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS
476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round
galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners
of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary
intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600
mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long
8mm outer diameter M-6dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm
length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre
along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter
wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help
of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed
bottom portion of all T-sections used in false ceiling support system shall be prepainted with
polyester baked paint, for all heights. The work shall be carried out as per specifications,
drawings and as per directions of the engineer-in-charge.
With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6)
[10/80]
Page - 11
Bill of Quantities (BoQ)
126 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar sqm 6041.49
refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and
sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement :
4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1,
including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting
upto 150 mm height along the parapet walls in the same manner.
127 Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid sqm 6041.49
Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-
45 kg/cum), over a coat of polyurethane primer applied @ 6-8 sqm per litre, laying 400 G
polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed
1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough
finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints
with polymerized mastic, all complete as per direction of Engineer-in-Charge.
132 Providing and applying white cement based putty of average thickness 1 mm, of approved brand sqm 21957.44
and manufacturer, over the plastered wall surface to prepare the surface even and smooth
complete.
133 Finishing walls with textured exterior paint of required shade : sqm 5776.69
New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of
exterior primer applied @ 2.20kg/10 sqm.
134 Painting one or more coats with black Japan paint of approved brand and manufacture to give an sqm 221.32
even shade.
135 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less sqm 24618.93
than 50 grams/ litre, of approved brand and manufacture, including applying additional coats
wherever required, to achieve even shade and colour.
Two coats
136 Providing & fixing 150mm wide Chicken wire mesh on joints of RCC & Brick work before sqm 2195.74
plastering complete in the direction of Engineer-in-charge.
137 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per sqm 58311.24
manufacturer's specifications including appropriate priming coat, preparation of surface, etc.
complete.
On steel work
138 SUB HEAD-XI :- ALUMINIUM WORK kg 24098.85
Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded
built up standard tubular sections/ appropriate Z sections and other sections of approved
make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or
with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom
and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free,
straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum
snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be
paid for separately) :
For fixed portion
Powder coated aluminum (minimum thickness of powder coating 50 micron)
139 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and kg 22819.44
making provision for fixing of fittings wherever required including the cost of PVC / neoprene
gasket required (Fittings shall be paid for separately).
Powder coated aluminum (minimum thickness of powder coating 50 micron)
[11/80]
Page - 12
Bill of Quantities (BoQ)
143 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing sqm 2769.32
treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs,
podiums, reservior, sewage & water treatment plant, tunnels/subway and bridge deck etc.,
prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for
vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces
and applying the same from negative (internal) side with the help of synthetic fiber brush. The
material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing
permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and
resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable
of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as
per specification and the direction of the engineer-in-charge. The product performance shall carry
guaranteed for 10 years against any leakage.
For vertical surface two coats @0.70 kg per sqm per coat
144 For horizontal surface one coat @1.10 kg per sqm. sqm 6673.03
145 Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline metre 1230.81
mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and
spalled & honeycombed surface of RCC underground structures like basement, water tanks,
bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3
having compressive strength Class R4 > 45 MPa and adhesive bond strength Class R3 > 1.5
MPa. The work shall be carried out all complete as per specification and the direction of the
Engineer-in-charge. The product performance shall carry guarantee for 10 years against any
leakage.
For sealing cracks and faulty construction joints, by preparing the surface, making U-shape
groove size of 25x25mm and then priming the surface with integral crystalline slurry @0.05kg per
running meter and while the surface is tacky then filling the groove upto top edge with crystalline
mortar @1.50kg per running meter. Once crystalline mortar is touch dry then finally applying two
coats of integral crystalline slurry @0.05kg per running meter per coat on treated surface.
146 For patching of tie rod holes, preparing tie rod hole surface and then priming the area with each hole 923
integral crystalline slurry @0.070kg per sqm and while the surface is tacky, repairing and then
filling the tie rod holes with crystalline mortar @0.040kg per hole. The crystalline mortar shall be
tightly rodded into tie rod holes or packed tightly (For 25x25x25 mm tie rod hole, use 0.040 kg to
fill the hole)
147 Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter metre 1230.81
(expansive nature) for construction joints treatment of RCC structure, such as raft slab, retaining
walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After
cleaning the surface, one coat of required primer for swellable water stop tape shall be applied
throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface
swellable type water stop tape shall be placed. The work shall be carried out all complete as per
specification and the direction of the engineer-in-charge. The product performance shall carry
guaranteed for 10 years against any leakage.
148 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by sqm 753.60
applying cement slurry mixed with water proofing cement compound consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound
@ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.
(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement
compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water
curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints,
corners, junctions of pipes and masonry with polymer mixed slurry.
149 Providing and laying broken AAC block in sunken portion of W.C. & kitchen. These broken Block cum 278.25
mixed with cement mortar 1:8 ( 1 cement : 8 coarse sand) laid and compacted properly including
supply of labour, material, and tools and plant etc. as per instruction of Engineer-in-charge.
[12/80]
Page - 13
Bill of Quantities (BoQ)
151 SUB HEAD-XII:- STRUCTURAL GLAZING, CURTAIN GLAZING, ALUMINIUM COMPOSITE Kg 23935.42
PANEL WORK
Providing and supplying aluminium extruded tubular and other aluminium sections as per the
rchitectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5
or T6 as per BS74,including super durable powder coating of 60-80 microns conforming to
AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item
includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of
extruded aluminium frame work. Nothing extra shall be paid on this account).
152 Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized sqm 1595.69
system of structural glazing (with open joints) for linear as well as curvilinear portions of the
building for all heights and all levels, including:
a) Structural analysis & design and preparation of shop drawings for the specified design loads
conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind
pressure without any failure), including functional design of the aluminum sections for fixing
glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets,
screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire
stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure
equalisation & drainage and protection against fire hazard including:
b) Fabricating and supplying serrated M.S. hot dip galvanised /Aluminium alloy of 6005 T5
brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement
for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/
masonry/structural steel framework of building structure using stainless steel anchor fasteners/
bolts,
nylon separator to prevent bimetallic contacts with nuts and
washers etc. of stainless steel grade 316, of the required
capacity and in required numbers.
c) Providing and filling, two part pump filled, structural silicone sealant and one part weather
silicone sealant compatible with the structural silicone sealant of required bite size in a clean and
controlled factory / work shop environment , including double sided spacer tape, setting blocks
and backer rod, all of approved grade, brand and manufacture, as per the approved sealant
design, within and all around the perimeter for holding glass.
d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes,
shapes and profiles, as required as per the site conditions, to seal the gap between the building
structure and all its interfaces with curtain glazing to make it watertight.
e) Making provision for drainage of moisture/ water that enters the curtain glazing system to
make it watertight, by incorporating principles of pressure equalization, providing suitable gutter
profiles at bottom (if required), making necessary holes of required sizes and of required
numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating
and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other
[13/80]
Page - 14
Bill of Quantities (BoQ)
162 Laying spreading and compacting stone aggregate of specified sizes to WBM specifications cum 784.10
including spreading in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller
8-10 tonne in stages to proper grade and camber, applying and brooming requisite type of
screening/binding material to fill up interstics of coarse aggregate watering and compacting to
the required density.
163 Providing and laying 400 micron thick PVC Sheet on WBM Surface complete as per direction of sqm 2614.10
engineer-in-charge.
164 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. cum 1265.83
The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum
dewatering process and finally finished by floating, brooming with wire brush etc. complete as per
specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for
separately).
(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as
per design mix is payable/ recoverable separately).
165 Providing & Fixing in position premoulded joint filler in expansion joint per cm 7469.82
depth per
cm width
per m
length
166 Providing and laying in position bitumen hot sealing compound for expansion joints etc. per cm 7469.82
16.46.1 Using grade 'A' sealing compound. depth per
cm width
per m
length
167 PAINTING ROAD / RUNWAY MARKING sqm 41.60
Painting runway/taxi track/apron marking with adequate no. of coats to give uniform finish with
road marking paint of superior make as approved by the Engineer-in-charge i/c cleaning the
surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete
New work (Two or more coats)
168 Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 sqm 1299.63
grade made by block making machine with strong vibratory compaction and of approved size and
design/shape laid in required colour and pattern over and including 50 mm thick compacted of
coarse sand, filling the joints with coarse sand etc. all complete as per direction of engineer-in-
charge.
[14/80]
Page - 15
Bill of Quantities (BoQ)
170 Providing and fixing factory made precast RCC perforated drain covers, having concrete of each 415
strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos
longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations
@ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm
complete, all as per direction of Engineer in-charge.
171 Providing and fixing 10x10 x7.50 cm stone block hand cut and chisel dressed on top, for paving Sqm 293.17
in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints
10mm wide filled with same mortar including ruled pointing etc. complete as per direction of
engineer-in-charge.
172 SUB HEAD-XIIII :- HORTICULTURE & LANDSCAPING cum 3952.35
Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable
materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50
m and making up the trenched area to proper levels by filling with earth or earth mixed with
sludge or/and manure before and after flooding trench with water (excluding cost of imported
earth, sludge or manure).
173 Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth cum 3293.63
measured in stacks will be reduced by 20% for payment).
174 Supplying and stacking at site dump manure from approved source, including carriage up to 1 cum 548.94
km (manure measured in stacks will be reduced by 8% for payment) :
Screened through sieve of I.S. designation 20 mm
175 Screened through sieve of I.S. designation 16 mm cum 548.94
178 Spreading of Sludge Farm Yard Manure or/and good Earth (Spreading of sludge farm yard cum 548.94
manure or/ and good earth in required thickness (cost of sludge, farm- yard manure or/and good
earth to be paid for separately))
179 Mixing earth and sludge or manure in the required proportion specified or directed by the Officer- cum 548.94
in-charge..
180 Grassing with ' Doobs' Grass (Grassing with 'Doobs' grass including watering and maintenance sqm 4391.50
of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for
moving including supplying good earth if needed)
i) In rows 15 cm apart in either direction
181 In rows 7.5 cm apart in either direction sqm 4391.50
182 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure each 50
or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20%
: 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing
including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure,
sludge or extra good earth if needed to be paid for separately) :
Holes 60 cm dia, and 60 cm deep.
183 Holes 45 cm dia, and 45 cm deep. each 50
184 Tree Guard with MS Iron (Providing and fixing MS iron tree guard 60 cm dia and 2 metre high each tree 50
above ground level formed of 4 Nos (25 x 6 mm) and 8 Nos (25 x 3 mm) vertical MS riveted to 3 guard
Nos (25 x 6 mm) iron rings in two halves, bolted together with 8 mm dia and 30 mm long bolts
including painting two coats with paint of approved brand over a coat of priming, complete in all
respects.)
185 Tree Guard with MS Angle Iron and Steel Wire (Providing and fixing tree guard 0.60 metre each tree 50
square, 2.00 metre high fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25 x 3 mm and guard
steel wire3 mm dia welded and fabricated as per design in two halves bolted together)
186 GROUND COVERS PLANTS each 50
Providing and Displaying of Wadelia trilobata plant, full of leaves in 15 cm size of Poly bags & as
per direction of the officer-in-charge.
187 Providing and Displaying of Duranta Golden plant, having ht.15 to 20 cm bushty shape plant with each 25
fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the
officer-in-charge..
188 Providing and Displaying of Iresine herbstii plant, of height 20-30 cm. full of branches well each 25
developed in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.
[15/80]
Page - 16
Bill of Quantities (BoQ)
206 Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 Kg 2827.20
cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary
welding and applying a priming coat of approved primer on exposed surface etc. complete.
207 SUB HEAD: 'B1': PLUMBING WORKS & F/F Each 115
SUB HEAD I - SANITARY FIXTURE & FITTINGS
Supply and install white vitreous china extended wall mounted water closet of approved shape
(size: 540mmx360mmx335mm depth) including providing and fixing vitreous china concealed
cistern with duel flush fitting, of flushing capacity 3 litre/6litre and adjustable 2litre/4 Litre including
seat cover, and cistern fitting, nuts, boltsand gasket etc complete.
208 Supply and install white vitreous china powered by 220 volt AC Model based infrared sensor Each 103
operated urinal of 558x325mm approx. having Flow rate at 45 psi ≤ 2.5 lpm with concealed
urinal sensor, having water inlet from back side, including fixing to wall with suitable brackets all
as per manufacturers specification and direction of Engineer.
209 Supply and install Wash basin vanity in white color for over counter mounting (Size:450mm x Each 92
450mm), specially fabricated brackets, painted white, 32mm dia CP waste and connections
pipe 450mm / 600mm long braided hose with nipple, nut, oring and rubber washer etc complete.
with C.P. wall flange and rubber adopter for waste connection, complete including cutting and
making good the walls, wherever required.
210 Supply and install CP brass single lever low flow wash basin mixer Flow rate at 45 psi ≤ 6 lpm Each 34
with 15 mm CP single lever pillar cock with pop up and waste complete including cutting and
making good the walls where required.
211 Supply and install CP brass push type pillar tap for wash basin Flow rate at 45 psi ≤ 6 lpm with Each 58
waste coupling complete including cutting and making goood deck mounted basin Faucet.
212 Supply and install Salem Stainless Steel kitchen sink (Size: 610mm x 460mm x 205 mm) without Each 3
drain board as per manufacturers specification and direction of Engineer with CI brackets and
stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and
making good the walls wherever required.
213 Supply and install CP brass single lever low flow Sink mixer Flow rate at 45 psi ≤ 6 lpm with 15 Each 3
mm CP single lever pillar cock with pop up and waste complete including cutting and making
good the walls where required.
214 Supply and install of 15mm C.P shower arm 190mm long with divertor with provision for over Each 2
head shower with spout and with wall flange including cutting and making good the walls,
wherever required.
215 Supply and install towel ring (Size:210mmx160mm) including cutting and making good the Each 66
walls/doors wherever required complete as directed by Engineer In charge.
216 Supply and install CP angular stop cock with wall flange 15mm dia for basin mixer, health faucet Each 115
and geyser points
[16/80]
Page - 17
Bill of Quantities (BoQ)
219 Supply and install hand shower (Health faucet) Flow rate at 45 psi ≤ 6 lpm with 1mtr long Easy Each 115
Flex Tube in chrome finish and wall hook.
220 Providing & fixing glass urinal partition of Height: 900mm,Width: 450mm &Frosted Safety Glass: Each 99
8 mm with fixed with expandable anchor fasteners with C.P. brass bolts and washers, embedded
in wall with anchor and set in cement concrete complete including cutting and making good the
walls wherever required.
221 Supply and install towel rail single towel rail 600mm long including fixing of brackets with CP Each 2
screws with concealed fitting arrangement of approved quality and colour.
222 Supply and install C.P brass short body bib cock of approved quality as per manufacturers Each 17
specification and direction of Engineer.
15 mm nominal bore
223 Supply and install Toilet Paper Holder with flap complete including cutting holes in wall and Each 115
making good the wall wherever required.
224 Supply and install first quality bottle trap (with internal partition) 32mm size with 190mm long Each 92
wall connection pipes and wall flange.and waste coupling 32mm size full thread with 130mm
height etc complete in all respect as per site.
225 Supply and install wall mounted Stainless steel grab bars of 600mm long grab bar including Each 9
cutting & making good the walls .
226 Supply and install satin finish stainless steel 316 grade wall mounted coat hooks/peg rag on door Each 115
complete.
227 Supply and install of cp brass soap dish of approved design Each 2
228 Supply and install solid state no touch operating fully highgenic SS hand drier of best quality, to Each 22
be operated with 230 volts, single phase, with fully hygienic condition, with all accessories
including cutting and making good the walls, wherever required.
229 Providing and fixing CP brass waste for wash basins and sinks. Each 3
32 mm dia
230 Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) Each 60
complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with CP brass screws
and washers.
231 Providing and fixing PVC connection pipe with brass union. Each 133
45 cm length
15 mm nominal bore
232 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS Each 12
standards and weighing not less than 690 gms.
15mm nominal bore
233 Providing and fixing CP brass angle valve for basin mixture and geyser points of approved Each 133
quality confirming to IS: 8931.
234 Supply and install 6mm thick beveled edge glass mirror with side polished complete including Sqm 72.00
fixing over marine plywood frame work at all levels & height including fixing of molded ,screw and
silicon etc. incl labors, tools, scaffolding at all heights as per Direction of EIC
.
235 Supply and install S&S grating of approved quality and colour. Each 26
Circular type
100 mm nominal dia
236 125 mm nominal dia with 25 mm waste hole. Each 145
237 Providing, Installing & fixing storage type water heater of approved shade with copper container, Each 7
glasswool insulation, stove enamelled M.S jacket, thermostatically controlled inner heater with
pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible
connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required.
Capacity 25 litres
238 SUB HEAD II - SOIL, WASTE , VENT WATER PIPES Metre 1882.00
Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes
100 mm dia
239 75mm dia Metre 284.00
240 Providing and fixing sand cast iron heel rest sanitary bend. Metre 33.00
100 mm dia
241 Providing and fixing sand cast iron single equal plain junction of required degree with access Each 77
door, insertion rubber washer 3 mm thick, bolts and nuts complete.
100 x 100 x 100mm
242 80x80x80 mm Each 12
243 Providing and fixing single equal plain junction of required degree . Each 370
100 x 100 x 100mm
244 80x80x80 mm Each 72
245 Providing and fixing sand cast iron trap of self cleaning design with sand cast iron screwed down Each 166
or hinged grating with or without vent arm complete including cost of cutting and making good
the walls and floors.
100mm inlet and 100mm outlet
[17/80]
Page - 18
Bill of Quantities (BoQ)
[18/80]
Page - 19
Bill of Quantities (BoQ)
[19/80]
Page - 20
Bill of Quantities (BoQ)
344 Providing, Fixing, Testing & Commissioning of nitrle rubber insulation on hot water supply pipes. Metre 142.00
K-Flex, A-Flex, Armacell
15mm (9 mm thickness)
345 20mm (9 mm thickness) Metre 142.00
346 25mm dia (9 mm thickness) Metre 85.00
347 32mm dia (9 mm thickness) Metre 55.00
348 40mm dia (13 mm thickness) Metre 35.00
349 50mm dia (13 mm thickness) Metre 150.00
350 65mm dia (13 mm thickness) Metre 75.00
351 80mm dia (13 mm thickness) Metre 75.00
352 SUB HEAD IV - SEWERAGE & DRAINGE SYESTEM Metre 259.00
Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar
in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.
150 mm dia SW pipes
[20/80]
Page - 21
Bill of Quantities (BoQ)
361 Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 Each 15
fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm
nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40
mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse
sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 :
4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished
complete as per standard design.
Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm
internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover
and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg).
367 Constructing brick masonry circular manhole 0.91m internal dia at bottom and 0.56m dia at top in Each 5
cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation
concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and
making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per
standard design.
0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal
diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg.
fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm
nominal size) including centering shuttering all complete. Excavation, foot rests and 12mm thick
cement plaster at the external surface shall be paid for separately).
With common burnt clay F.P.S.( Non modular) bricks of class designation 7.5
368 Extra depth for circular type manhole 0.91m internal dia. ( at bottom) beyond 0.91m to 1.67m. Metre 2.00
With common burnt clay F.P.S.( Non modular) bricks of class designation 7.5
369 Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in Each 5
cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation
concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and
making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per
standard design.
1.68m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal
diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg.
fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm
nominal size) including centering shuttering all complete. Excavation, foot rests and 12mm thick
cement plaster at the external surface shall be paid for separately).
With common burnt clay F.P.S.( Non modular) bricks of class designation 7.5
[21/80]
Page - 22
Bill of Quantities (BoQ)
[22/80]
Page - 23
Bill of Quantities (BoQ)
383 Providing, fixing, testing & commissioning of MSEP water softening plant (suitable for 3 Kg/Sqcm Set 1
working pressure) complete with initial charge with T-40 NA Resin, multiport valve with built in
ejector for controlling all operations), regeneration system and HDPE tank, pressure gauge at
inlet, outlet and back wash (each with isolation cock), valves, fittings and water hardness testing
kit & associated works. Softener shall be suitable for the following duty:
Note: The successful contractor will have to carry out a test of raw water from all the sources of
water for the Commercial, Residential & apartment at their own cost from a reputed lab as
approved by the Engineer-in-Charge / Consultant. On the basis of these results the contractor
has to submit his shop drawings, design calculations and specifications accordingly.
Please note that it is ultimately the responsibility of the contractor to provide treated water for
different use as per International Standard as given in the attached guidelines.
Raw water hardness 500 Mg/L
Treated water hardness 100 Mg/L
Regeneration Period 12 Hrs.
Capacity : 700 lpm
384 Supplying, installing, testing and commissioning of dosing system (for domestic water treatment Set 1
plant) consisting of one HDPE tank of 100 litres capacity with a positive displacement diphragm
dosing pump having variable flow rate of 0-6 lph. The motor shall be suitable for operation at 240
V / single phase/50 Hz. Supply. The pump shall be supplied complete with necessary
polypropylene piping, valves, strainers, low level switch and injection fittings. The pump shall be
speed & stroke control Asia LMI / equivalent make.
The cost shall be inclusive of providing salt for the testing and operation of system before
handover to the owner.
385 Supplying, installing, testing and commissioning of annunciation and indication panel with Each 1
interlocking arrangement complete in accordance to specification for level controller etc with
control cabling from field to MCC as required.
The system shall be complete to ensure automatic operation of pump in accordance to water
level in respective tanks.
386 Providing & fixing level controllers for water pumps to start/stop the pump at set level. Including Each 1
wiring, cabling from pump to panel & all other accessories as required to operate the system
automatically.
387 Providing & fixing pressure switch for water pumps to start/stop the filter feed pump at set Each 5
pressure. Including wiring, cabling from pump to panel & all other accessories as required to
operate the system automatically.
[23/80]
Page - 24
Bill of Quantities (BoQ)
[24/80]
Page - 25
Bill of Quantities (BoQ)
[25/80]
Page - 26
Bill of Quantities (BoQ)
432 Supply of Cables , Connector, Cable Trays, to make Electrical Installation Complete. Necessary Lot 1
cable alleys, internal / cabling, wiring, cabling from MCC to various pumps / equipment and
interlocking, earthing and earthing pits for all equipment .
433 Installing & fixing cast-iron manhole cover and frame suitable for 600mm dia manhole with Each 8
lockable and lifting arrangement. The entire item shall be epoxy coated and approved by
insecticide department
Medium duty double seal of size 560 mm dia and total weight of cover & frame to be not less
than 116 KG. (Location : U/G Water Tanks Top)
[26/80]
Page - 27
Bill of Quantities (BoQ)
439 SUB HEAD VII -ELECTRICAL PANEL BOARDS FOR PHE WORKS. Item 1
ii) For 2 x 2 HP sump Pump (1 Duty + 1 Stand by)
CUBICAL PANEL BOARD - PLUMBING
i) For 2 x 5.0 HP Domestic Water fixed speed hydroneumatic Pumps (1 duty + 1 stand by)
Supply, installation, testing and commissioning of Cubical type sectionalised floor standing
switch board of 31 MVA fault capacity at 415 V complete with 3.5 strip, 160 A capacity Aluminium
Bus - Bar Electrolytic grade, cable alley, switchgears of following capacity & as per specifications.
A) INCOMER
100 A TP MCCB with heavy duty solid neutral link with (0-100A) ammeter with 3 CT and selector
switch, (0 - 500 V) voltmeter with selector switch, phase indication light with protection fuse. - 01
S
B) OUTGOINGS
i) For 2 x 3.0 HP Domestic Water fixed speed hydroneumatic Pumps (1 duty + 1 stand by)
II) For 2 x 2 HP sump Pump (1 Duty + 1 Stand by)
40 A TP MCB with 40 A DOL starter, overload relay, 96 mm (0-40A) ammeter with single CT,
start / stop push buttons, on / off / trip indication lights with protection fuse, single phase
preventer. - 01 set.
25 A TP MCB with 25 A DOL starter, overload relay, 96 mm (0-25A) ammeter with single CT,
start / stop push buttons, on / off / trip indication lights with protection fuse, single phase
preventer. - 01 set.
446 Centring and shuttering including stutting, propping etc. and removal of form for: Sqm 40.00
Suspended floors, roofs, landings, balconies and acees platform
[27/80]
Page - 28
Bill of Quantities (BoQ)
450 Providing and fixing in position precast RCC manhole cover and frame of required shape and Each 25
approved quality.
HD-20 circular shape 560 mm internal diameter.
451 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in Metre 250.00
IS: 2800 (part I), including collecting samples from different strata, preparing and submitting
strata chart/bore log, including hire & running charges of all equipments, tools, plants &
machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90
metre depth below ground level.
All types of soil
400 mm dia.
452 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC Metre 150.00
medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire
and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of
Engineer –in-charge.
200 mm nominal size dia.
453 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC Metre 150.00
medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour
charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-
charge.
200 mm nominal size dia.
454 Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge Cum 25.00
pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-
charge.
455 Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, Cum 10.00
over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per
direction of Engineer-in-charge.
456 Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge Cum 15.00
pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of
Engineer –in-charge.
457 Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel Cum 10.00
fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per
direction of Engineer-in-charge.
458 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore Each 10
well housing/ casing pipe, removable as per requirement, all complete for bore well of:
200 mm dia
459 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as Each 2
per IS: 2800 (part I), including necessary bolts & nuts of required size complete.
200 mm clamp.
460 TUBEWELL Each 6
Providing and laying in position cement concrete of specified grade excluding the cost of
centering and shuttering - All work up to plinth level :
1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size )
461 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in Metre 150.00
IS: 2800 (part I), including collecting samples from different strata, preparing and submitting
strata chart/bore log, including hire & running charges of all equipments, tools, plants &
machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90
metre and upto 150 metre depth below groung level.
All types of soil
400 mm dia
462 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC Metre 150.00
medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire
and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of
Engineer –in-charge.
200 mm nominal size dia.
463 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC Metre 150.00
medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour
charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-
charge.
200 mm nominal size dia.
464 Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel Cum 120.00
fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per
direction of Engineer-in-charge.
[28/80]
Page - 29
Bill of Quantities (BoQ)
487 Supply, Fixing & commissioning of 2" Large Capacity Y Filters for sub main filtration ,Maximum Nos 1
Flow Up to 110 gpm (25m³/hr), Maximum Pressure 116 psi (8 bar),Maximum Temperature Up to
140ºF (60ºC). LCRBY200D
488 Supply, Fixing & commissioning of 63mm/50mm/40mm dia self-closing flushing valves. Nos 1
489 Supply, Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Non - Nos 25
Obtrusive Brown Colored Fittings of 17mm BARBX BARB TEE
490 Supply, Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit.Non - Nos 25
Obtrusive Brown Colored Fittings of 17mm BARBX BARB COUPLING
491 Supply, Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Non - Nos 10
Obtrusive Brown Colored Fittings of 17mm BARBX BARB ELBOW
[29/80]
Page - 30
Bill of Quantities (BoQ)
516 Supply, Fixing & Commissioning of Direct burial14 Awg x 2 Maxi cable with PVC insulated UL Mtr 1000.00
standard 493 with impregnated polyethylene jacket and soft annealed tin coated copper
confirming to ASTM B-33 for two way communication between decoder controller and decoders
complete with suitable conduit pipe
[30/80]
Page - 31
Bill of Quantities (BoQ)
[31/80]
Page - 32
Bill of Quantities (BoQ)
1.NOC from fire authority shall be in the scope of Contractor . Only fee paid to the fire authority
shall be reimbursed against the submission of the receipt and nothing shall be paid extra.
2. All the Fire Fighting works shall be done in compliance of Fire Fighting authority requirement.
Pump shall be capable of furnishing not less than 150% of rated capacity at a head not less than
65 % of rated head. The shut off head shall not exceed 120% of rated head.
531 Supplying Installation, testing and Commissioning of electric driven main fire pump suitable for Set 1
automatic operation and consisting of following Complete in all respect as required.
Horizontal type, single / multistage, centrifugal, split casing pump of cast iron body and bronze
impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5
kg/sq.cm. at highest and farthest outlet at specified flow of 1620 LPM at 35 Metres head
conforming to IS 1520.
Suitable HP SQ cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for
operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot
mounted type with Class-'F' insulation, conforming to IS-325
M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.
Suitable cement concrete foundation duly plastered with anti vibration pads and suitable size
copper unarmoured cables upto 15 mtr. Length (Above 15 mtr. will be paid separately) complete
with connection interconnection as reqd.
(For Water Curtain System).
[32/80]
Page - 33
Bill of Quantities (BoQ)
[33/80]
Page - 34
Bill of Quantities (BoQ)
540 Supply, installation, testing and commissioning brass orifice plates made out of 8mm thick Nos. 25
stainless plate in pipelines to reduce pressure from 8 kg. to 3.5 kg/sq.cm. Complete as per
manufacturer's specifications & as directed by Engineer- in-charge.
80/100 mm dia.
541 Supplying and fixing, testing and commissioning of 1 Set of 63mm instantaneous 4 way fire Set 2
brigade inlet connection (FBC) comprising of S.S and S.S instantaneous male inlet coupling
confirming to IS:604 with 1 No. 150 mm diameter butterfly valve, 1 No. 150mm dia. Non-return
valve, plug and cap with chain as required with nut & bolts, washers, high pressure gasket as
required. Complete as per manufacturer's specifications & as directed by Engineer- in-charge.
(FOR UG TANK & EXTERNAL RING MAIN)
542 Supplying and fixing, testing and commissioning of 1 Set of 63mm instantaneous 2 way fire Set 1
brigade draw out connection (FBC) comprising of S.S and S.S instantaneous male inlet coupling
confirming to IS:604 with 1 No. 150 mm diameter butterfly valve, 1 No. 150mm dia. Non-return
valve, plug and cap with chain as required with nut & bolts, washers, high pressure gasket as
required. Complete as per manufacturer's specifications & as directed by Engineer- in-charge.
(FOR UG TANK)
543 Providing and fixing air vessel made of 250 mm dia. 8 mm thick MS sheet, 1200 mm in height Nos. 8
with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia
gunmetal wheel valve. With required accessories. Pressure gause and painting with synthetic
enamel paint of approved shade as required.
544 Supplying Installation, testing and Commissioning of electric driven Terrace fire pump suitable for Set 1
automatic operation and consisting of following Complete in all respect as required.
Horizontal type, single / multistage, centrifugal, split casing pump of cast iron body and bronze
impeller with stainless steel shaft, mechanical seal conforming to IS 1520.
Suitable HP SQ cage induction motor, TEFC, synchronous speed 2900 RPM, suitable for
operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot
mounted type with Class-'F' insulation, conforming to IS-325
M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.
Suitable cement concrete foundation duly plastered with anti vibration pads.
545 SUB HEAD-2.0 PIPING FOR FIRE HYDRANT, SPRINKLER & WATER CURTAIN SYSTEM Meter 610.00
Providing, fixing, testing and commissioning of the following size of flange jointed / screwed /
welded, M.S. pipes of Class C (heavy class) ISI marked and of approved make, IS : 1239/3589
including accessories such as tees / elbows / reducers / couplings / unions / bends / flanges etc.,
including excavation in all kinds of soil and all types of roads, direct in ground to a depth of 30 cm
to 1 mtr as per site condition i/c concrete supports/anchors/ thrust pads and refilling the trench
along with disposal of melba to the nearest dumping ground, and wrapping with 1 no. 4 mm thick
polymeric corrosion protection tape conforming to IS 10221 and painting with bituminous paint
after laying and testing to 13.5 Kg / Sq. cm hydraulic pressure after installation etc as per
specification complete as required. ( For Underground )
150 mm nominal bore
[34/80]
Page - 35
Bill of Quantities (BoQ)
[35/80]
Page - 36
Bill of Quantities (BoQ)
579 6 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers Nos. 28
580 9 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers Nos. 10
581 Providing, fixing, testing and commissioning of 50 Litres (trolley mounted) Mechanical Foam type Nos. 2
Fire Extinguisher. In HP Mild Steel Cylinders ISI marked TAC approved fitted with pressure
indicating gauge, internal tube, squeeze lever type valve fully charged complete in all respects
including wall suspension bracket / trolley mounted and conforming to IS:910 .
582 Providing, fixing, testing and commissioning of CO2 type Fire Extinguisher of capacity 22.5 kg Nos. 2
filled with Co2 Gas as per IS 15222 with control discharge mechanism fitted with Hose, Horn &
TROLLEY confirms to IS 2878 bearing ISI mark. Co2 Cylinder as per IS 7285
583 Providing and fixing Fire related signages printed on photo luminescent U1000 aluminium sheet Square 8500.00
of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating Inch
and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers,
cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge.
[36/80]
Page - 37
Bill of Quantities (BoQ)
594 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as Meter 30.00
required.
595 SUB HEAD : 6.0- LT & HT PANEL, ELECTRICAL ROOM & SERVER ROOM GAS FLOODING Nos. 8
SYSTEM
Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based
Novec 1230/ FK5-1-12 System for Electrical Panels (consisting of the following components:
5 Lb Novec 1230/ FK5-1-12, DLP Assembly with automatic valve mounted on DOT approved
cylinder, push in connector for tube, 5lb Novec 1230/ FK5-1-12 gas, mounting bracket, End of
Line adopter and low pressure switch for monitoring system activation.
596 10 Lb Novec 1230/ FK5-1-12, DLP Assembly with automatic valve mounted on DOT approved Nos. 11
cylinder, push in connector for tube, 10 lb Novec 1230/ FK5-1-12 gas, mounting bracket, End of
Line adopter and low pressure switch for monitoring system activation.
597 Linear pneumatic heat Detection Tube with all necessary fittings & supports. Meter 825.00
598 Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. Nos. 19
The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System.
599 Supply, fixing, testing and commissioning of 1x80 Itr completely system with CCOE approved set 2
high pressure, seamless Cylinders having suitable 80 ltr water capacity & suitable to store Novec
1230 (FK5-1-12) gas at 34.5 bar pressure with valve assembly, low pressure supervisory switch
for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other
accessories, mounting bracket, container straps, NRV. Electrically operated control head
capable of being electrically operated from the fire detection & control, Pressure operated control
head which shall allow for pressure actuation of gas mounted directly on top of cylinder valve,
manually operated actuator to actuate the gas flooding process with the help of a lever, flexible
rubber hose with wire bralded enforcement to route the gas from the storage cylinder to the
discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated
at the system piping or discharge manifold, Flexible actuation hose complete as required.
Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distribution Novec
1230 (FK5-1-12) gas to flood the hazard area as per requirement. Electrical non conductive,
Novec 1230 (FK5-1-12) required as per NFPA 2001 latest addition 4.7% Design Concentration.
Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel
compatible to Fire Alarm System. Makes : Firetrex / Trace fire/Safe Fire as approved by
architect.
600 SUB HEAD: 'C': ELECTRICAL WORKS Each 274
SH: I: POINT WIRING
Wiring for Light/Fan/Call Bell Point with 2X1.5 sq.mm. P.V.C. insulated single core unsheathed
industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed
electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent
make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid
ISI marked steel conduit pipe complete.
Short point upto 3.00 metre length.
601 Medium point upto 6.00 metre length. Each 685
602 Long point upto 10.00 metre length. Each 1872
603 Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) Metre 15067.00
cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor
for voltage grade up to 1100 volts (finolex/RR Kabel/Nicco/Anchor or Equivalent make as
approved by the Dept.) in surface/recessed ISI marked steel conduit pipe wiring system.
with 3X1.5 sq.mm cable in 20 mm dia. Rigid Steel conduit.
604 Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial Metre 7202.00
(Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper
conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved
by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed
conduit wiring system.
With 2X2.5 sq.mm. + earth continuity with 1X1.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.
605 With 2X4 sq.mm. + earth continuity with 1X2.5 sq.mm cable in 20 mm. dia. Rigid steel conduit. Metre 9312.00
606 With 2X6 sq.mm. + earth continuity with 1X4 sq.mm cable in 25 mm. dia. Rigid steel conduit. Metre 525.00
[37/80]
Page - 38
Bill of Quantities (BoQ)
608 With 4X4 sq.mm. + earth continuity with 2X2.5 sq.mm cable in 25 mm. dia. Rigid steel conduit. Metre 3612.00
609 With 4X6 sq.mm. + earth continuity with 2X4 sq.mm cable in 25 mm. dia. Rigid steel conduit. Metre 60.00
610 Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed Each 135
industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed
electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent
make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe
wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc.
as required complete.
Short point upto 3.00 metre length.
611 Medium point upto 6.00 metre length. Each 451
612 Long point upto 10.00 metre length. Each 918
613 Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed Each 32
industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed
electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent
make as approved by the Dept.) in surface/recessed conduit wiring system including earth
continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm.
dia. steel conduit (AK G or equivalent as approved by the Dept.)
Short point upto 3.00 metre length.
614 Medium point upto 6.00 metre length. Each 104
615 Long point upto 10.00 metre length. Each 376
616 Wiring for twin control light point with 1.5 sw. mm. P.V.C insulated single core unsheathed Each 12
industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed
electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent
make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid
ISI marked steel conduit pipe including 6 Amp flush type 2 way switch ( Anchor penta/Gold
medal /Kolor Kany.Kom/Havells or equivalent make as approved by the dept.) GI/MS switch
board (ISI marked) with phenolic laminated sheet cover, ceiling rode etc complete.
Short point upto 3.00 metre length.
631 Supplying with fitting and fixing of 6 amp one way modular clip in bell push MODEL RANGE Each 684
LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO),
CRABTREE (MURANO) including making necessary connections as per direction of department.
[38/80]
Page - 39
Bill of Quantities (BoQ)
633 Supplying with fitting and fixing of 6/10 amp two way modular clip in switch, MODEL RANGE Each 108
LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO),
CRABTREE (MURANO) including making necessary connections as per direction of department.
634 Supplying fitting and fixing industrial plug & socket in surface mounted SPN sheet steel powder Each 13
painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of
DP MCB complete with making necessary connection etc. as specified and directed by the Dept.
20A Capacity. (ABB, Schneider MG, legrand, Hager make)
635 Supplying fitting and fixing industrial plug & socket in surface mounted TPN sheet steel powder Each 2
painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of
4P MCB complete with making necessary connection etc. as specified and directed by the Dept.
(ABB, Schneider MG, legrand, Hager make).
20A Capacity
636 Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Each 16
Double door(IP-43) surface mounting SPN MCB DB incorporated with bus-bar, Neutral link,
Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making
necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG,
legrand, Hager, Crabtree xpro make).
8 way SPN double door
637 12 way SPN double door Each 11
638 Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Each 25
Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-
bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd.
complete with making necessary connection as approved , specified & directed by the dept.
(ABB, Schneider MG, legrand, Hager, Crabtree xpro make)
6 way TPN (8+6+18) double door
639 8 way TPN (8+6+24) double door Each 15
640 12 way TPN (8+6+36) double door Each 19
641 Supplying with fitting and fixing single pole 10KA 240/415V 50Hz MCB of the following capacity Each 1646
complete with making necessary connection as approved, specified and directed by the Dept. (
Schneider MG, legrand, Hager, Crabtree xpro make)
C Series
6 to 32A
642 Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete Each 20
with making necessary connection as approved, specified and directed by the dept. (ABB,
Schneider MG, legrand, Hager, Crabtree xpro make)
C Series
6 to 32A
643 40A Each 5
644 Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete Each 29
with making necessary connection as approved, specified and directed by the dept. (Schneider
MG, legrand, Hager, Crabtree Xpro make)
C Series
6 to 32A
645 40A Each 11
646 63A Each 21
647 Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the Each 107
following capacity complete with making necessary connection as approved, specified and
directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make)
30mA sensitivity DP RCCB
25A
648 40A Each 38
649 63A Each 63
650 100/300mA sensitivity DP RCCB Each 1
25A
651 40A Each 1
652 63A Each 1
653 Supplying with fitting and fixing Surge protector of max operation voltage 350V at 400 V network Each 25
for maximum discharge current 40KA with operator indicator and draw out cartridge of
(Schneider or equivalent make), of the following ways complete with making necessary
connection as approved, specified and directed by the dept.
Surge protection Max operating voltage 340V Standard type
1P+N
654 3P+N Each 61
655 Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor trunking Metre 367.00
including necessary nuts & bolts, washer etc. as required, as directed and specified by the
department. ( MK/ LEGRAND make) Size
100X38X1.6/1 compartment
656 150X38X1.6/2 compartment Metre 112.00
657 225X38X1.6/3 compartment Metre 73.00
658 250X38X1.6/3 compartment Metre 85.00
659 300X38X1.6/3 compartment Metre 85.00
[39/80]
Page - 40
Bill of Quantities (BoQ)
677 Supply and fixing of 25 mm dia 2.0mm average wall thickness heavy rigid PVC IS: 9537 Part - III Metre 7503.20
conduit (Berlia / AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by
the deptt.) in recessed system including cutting the wall and making good the some as required:
678 Supply and fixing of 32 mm dia 2.0mm average wall thickness heavy rigid PVC IS: 9537 Part - III Metre 1876.00
conduit (Berlia / AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by
the deptt.) in recessed system including cutting the wall and making good the some as required:
[40/80]
Page - 41
Bill of Quantities (BoQ)
[41/80]
Page - 42
Bill of Quantities (BoQ)
[42/80]
Page - 43
Bill of Quantities (BoQ)
[43/80]
Page - 44
Bill of Quantities (BoQ)
[44/80]
Page - 45
Bill of Quantities (BoQ)
[45/80]
Page - 46
Bill of Quantities (BoQ)
[46/80]
Page - 47
Bill of Quantities (BoQ)
[47/80]
Page - 48
Bill of Quantities (BoQ)
767 Supplying Fitting and Fixing of (Dowells / Commet make) Double compression brass gland with Each 206
nickel.
Weatherproof (CBW) Size:8-10, 3/4''
768 Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy Each 474
duty.
Single Compression Brass Gland Heavy Duty. Size:1''
769 Single Compression Brass Gland Heavy Duty. Size:1-1/8'' Each 84
770 Single Compression Brass Gland Heavy Duty. Size:1-1/2'' Each 14
771 Single Compression Brass Gland Heavy Duty. Size:1-3/4'' Each 8
772 Single Compression Brass Gland Heavy Duty. Size:2-1/4'' Each 8
773 Single Compression Brass Gland Heavy Duty. Size:2-3/4'' Each 86
774 Perforated RM30 Medium Duty Return Flange Cable Tray with Nos Splice RM 30 8-M6 X Gutter Metre 475.00
Bolt & Nuts upto 300mm and 3 Nos Splice, RM30 12 -M6 X Gutter Bolt & Nuts Above 300mm
including stand off bracket.
Size of Tray (in mm)
100
775 150 Metre 565.00
776 300 Metre 210.00
777 450 Metre 180.00
778 600 Metre 235.00
779 750 Metre 50.00
780 900 Metre 140.00
Bend
781 100 Each 48
782 150 Each 57
783 300 Each 21
784 450 Each 19
785 600 Each 24
786 750 Each 5
787 900 Each 14
Inter/Exter Bend
788 100 Each 24
789 150 Each 28
790 300 Each 11
791 450 Each 9
792 600 Each 12
793 750 Each 3
794 900 Each 7
Tee
795 100 Each 13
796 150 Each 14
797 300 Each 6
798 450 Each 5
[48/80]
Page - 49
Bill of Quantities (BoQ)
818 Supply, Installation, Testing & Commissioning of Surface Mounted LED Down lighter made of Each 154
pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type
and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt,
1200 Lumen Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up
to 6500 (SDCM<5), CRI >80, PF >0.90, an operating Voltage Range of 140 - 270 V.Minimum
Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI
compliance maintaining driver leakage current as per as per IEC 60598,Minimum system
Lumens 1200.Philips SM250C LED12S- 6500 PSU WH or equivalent.
819 Supply, Installation, Testing & Commissioning of Recess LED Down lighter made of pressure die Nos 194
cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture
should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of
fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5),
CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal
Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance
maintaining driver leakage current as per as per IEC 60598, Minimum system Lumens 1800.
Philips DN195B LED20S-6500 PSU WH S1 or equivalent.
820 Supply, Installation, Testing & Commissioning of 12 watt LED Mirror Light as complete as Nos 94
required. (Philips Make, Cat No - Mirror Light 32047/11 or equivalent.)
821 Supply, Installation, Testing & Commissioning of Surface Mounted Linear LED IP65 fitting made Nos 9
of Virgin Polycarbonate housing & Non Yellowing PC Diffuser ,LED Used shall be SMD type and
fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life
of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT 6500 (SDCM<5),
CRI >80 , PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal
Surge Protection 3KV The fixture design should comply with IS10322, EMC / EMI compliance
maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 4000.
Philips WT201C LED40S-6500 PSU L120 or equivalent.
822 Supply, Installation, Testing & Commissioning of Recess LED 600x600mm fitting made of white Nos 466
CRCA powder quoted finish with fully covered by PMMA Acrylic Lumio Diffuser, LED Used shall
be SMD type and fixture should have minimum efficacy at System level >=100lumens/watt, Life
of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80 , PF
>0.95 & THD<10%, Fixture must be office compliant & have to comply to UGR<19 value for
optimum glare.an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection
2.5KV The fixture design should comply with IS:10322 & Must be EMC / EMI compliance
maintaining driver leakage current as per as per IEC 60598, Minimum system Lumens 3000.
Philips RC380B LED30S -6500 G4 L60 W60 PSU OD OC LED Office Compliant Panel with Min
Glare Value i.e. UGR<19 or equivalent.
[49/80]
Page - 50
Bill of Quantities (BoQ)
832 Supply, Installation, Testing & Commissioning of Electronic Buzzer as complete as required. Meter 10.00
833 Supplying, Fitting and fixing of occupancy sensor of the following atageories as per required and Meter 111.00
directed by the department. (ABB/ Panasonic/ mk/ anchor/ crabtree/ Hager/ Panasonic or
equivalent make as approved by deptt.
presence detection with 360 degrees angle of detection with senser head power unit and 2
relays , range up to 4 meter at 2.5 meter ceiling height.
[50/80]
Page - 51
Bill of Quantities (BoQ)
[51/80]
Page - 52
Bill of Quantities (BoQ)
857 Supply , Installation , Testing and commissioning of armoured 6 core multimode OFC cable for Meter 1450.00
interfloor switch connectivity.
858 Supply , Installation , Testing and commissioning of 6 port loaded LIU with adaptor plates , pigtel Nos 9
cables for connections.
859 Supply , Installation , Testing and commissioning of 24 port loaded LIU for core switch to access Nos 2
switch connectivity over fiber.
860 Supply , Installation , Testing and commissioning of SC-LC multimode fiber patch cord. Nos 39
861 LIGHTNING PROTECTION AS PER IEC 62305 / IS IEC 62305 Mtr. 1125.00
Supply 8 mm round aluminium conductor for horizontal lightning protection - run in roof. Model :
AL8. Make : Hakel / APS
862 Supply of roof conductor holder for 8 mm round aluminium conductor made of Gun Metal for Nos. 900
horizontal installation. The distance between each holder should be min of 1.5 mtr. Model :
APSRCS50. Make : Hakel / APS
863 Supply of Cross connector for connecting of 8 mm Al round conductor . The connector should be Nos. 90
of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS
864 Supply of T connector for connecting of 8 mm Al round conductor . The connector should be of Nos. 15
Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS
865 Supply of L connector for connecting of 8 mm Al round conductor . The connector should be of Nos. 12
Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS
866 Supply of straight connector for connecting of 8 mm Al round conductor . The connector should Nos. 4
be of Gun Metal with SS nuts and bolt. Model : APSPCRC50, Make : Hakel / APS
867 Supply of Expansion piece to compensate the expansion of round 8 mm Al conductor when Nos. 4
temperature variation . Connection should be in every 20 mtr. Model : APSEXP50 , Make :
Hakel/APS
868 Supply of fixing glue for fixing of roof conductor holder . Pc 6
869 Supply of Expansion piece connector for connecting of 8 mm Al round conductor . The Nos. 6
connector should be of Gun Metal with SS nuts and bolt.
Model : APSCEP50- Make : Hakel /APS
870 DOWN CONDUCTOR AS PER IEC+D880 62305 Mtr. 705.00
Supply of 8 mm round aluminium conductor as a down conductor mounted in the surface of
wall which will carry the lightning current to earth pit. Model : AL8. Make : Hakel / APS
871 Supply of Down conductor holder for 8 mm round aluminium conductor of min distance Nos. 465
between the wall to the conductor will be of 50 mm. The distance between each holder should
be min of 1.5 mtr. Model : APSRCH50 Make : Hakel /APS
872 Supply of Test Joint Point for 8 mm round aluminium conductor , the size should be of 25 x 3 Nos. 3
x 150 mm copper in ABS boxes. Model : APSTLBCU. Make : Hakel / APS
873 EARTHING AS PER IEC 62561- 2 & 7 Nos. 16
SITC of UL approved low carbon high tensile steel rod with copper coating of min 254 micron
JK Chemrode - 317 CBR the dia should be 17.2 mm with length of 10 feet ( 3000 mm) . The rod
shall be as per IEC 62561-2 and approved by UL 467. The rod shall be tested from NABL lab
for current discharge not less then 46kA peak. The Chemrode shall be surrounded with 50 kg ( 2
bag) of Earth enhance materiel JK Activer+ according to IEC 62561-7 and the Chemical
resistance value shall not increase more then 0.064 Ωm and same will be tested from NABL
lab.
Make :APS/JK
[52/80]
Page - 53
Bill of Quantities (BoQ)
890 SITC of 2x250W Class-D Amplifier with 4 independent channels and can provide automatic re- Set 5
settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection.
Approved Makes : Bosch Praesedio / Honeywell - X618/ Ateis - IDA
891 SITC of Network Resource Interface, 4 channels network audio source, 32 dry contacts in and 8 Set 2
try contacts out for Fire Alarm Interface
892 SITC of 6W Ceiling mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. Set 265
The speaker shoud have tappings at 6W/3W
[53/80]
Page - 54
Bill of Quantities (BoQ)
894 Supply Installation Testing and Commissioning of 12 Watt volume controller with G.I. Box, Set 68
modular plate etc as complete as required.
895 Supply, Installation, Testing & Commissioning of 2C x 1.5 sq.mm Fire Survival armoured cable Meter 21535.00
(300/500V) with Class-2 Copper conductor having Mineral ceramic glass fire barrier tape covered
by an extruded layer of Cross-linkable Low Smoke Zero Halogen (LSZH) insulation as per EI-5
Of BS EN 50363 along with ATC drain wire, aluminium tape screening and LSZH outer sheath
as per BS 7629-1 & BS-5839-1 (latest edition). Outer sheath should be Anti Rodent/Anti Termite.
Should retain circuit integrity as per BS 8434-2 (930 deg C for 120 mins on single sample)
including end termination etc as complete as required. (For Fire & PA System)
903 Supply, installation, testing and commissioning of UL Listed , ONVIF profile S & G ,1/2.8" CMOS, Nos 7
IP Vari Focal Bullet Camera , Full, HD 3 MP Resolution , 2.8-12 mm Motorized Varifocal Lens ,
30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto
switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB
Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66
etc. Approved Makes: Allgovision/ Pelco/ Avigilon / Impulse/ Axis.
904 Supply, installation, testing and commissioning of UL Listed ONVIF profile S &G , 1/2.8" CMOS Nos 1
Box type camera , external lens 5mm to 50 mm, Full, HD 3 MP Resolution ,3MP@25FPS , 2 MP
@ 50 FPS , Quad Stream with Edge Based Analytics, Shutter speed 1 ~ 1/10000 sec, SD card
support , P-iris, ONVIF profile S & G etc. .Approved Makes :Allgovision/ Pelco/ Avigilon /
Impulse/ Axis.
905 Supply , Installation , Testing and Commissioning of 6 MP , Fish eye Camera ,ONVIF profile S & Nos 1
G , UL,CE,FCC certified , 1/1.8" CMOS lens , 1.55 mm focal length , shutter speed :1 ~ 1/10000
sec , Quad stream , Frame rate : 6MP @ 25 fps , 2 MP @ 50 fps , Digital Zoom , Two way audio
support ,Auto white balance ,Inbuilt IR LED , IR Distance upto 5 mtrs ,IP 66 weather proof ,
POE. Approved Makes: Allgovision/ Pelco/ Avigilon / Impulse/ Axis.
906 Supply, installation, Testing and Commissioning of Open Platform ONVIF profile S &G Network Nos 1
Video Recorder, Intel based, Full Rack, RAID 0/1/5/10, @ 2M/30FPS, 1*2.5" SATA + 8 * 3.5"
SATA, Throughput: 640 Mbps.1 X HDMI , 1X VGA ,, 1 X mic in , 1 X line out , USB 3.0 x 2 + USB
2.0 x 3 , 1 X WAN port , 1 X LAN port , pre-installed VMS :Approved Makes :Allgovision/ Pelco/
Avigilon / Impulse/ Axis.
907 Supply, installation, testing and commissioning of UL Listed , ONVIF Compliant 1/2.8" IR PTZ Nos 3
Speed Dome Camera max resolution 3 MP , 0.05 @ F1.6 (Color), 0 (B/W) @ F1.6, Quad
Streams, IR Distance 150m, Edge Analytics, 120DB Wide Dynamic Range, H264 Compression,
IP66 Motorized Lens 4.3-129mm 30x Optical zoom Audio in/out 1/1, Micro SD slot, IP66 etc.
Approved Makes :Allgovision/Pelco/Avigilon / Impulse/Axis.
908 Supply, Installation, Testing & Commissioning of Core Switch with switching capacity of 1.4Tbps, Nos 1
forwarding performance of 1Bpps with 32x 1/10G SFP+ ports plus 4x 40G QSFP+ ports from
day 1, dual hot swappable internal power supply, 60K IPv6 routes and 48K IPv6 multicast routes.
Should support advance layer 3 (RIPng, OSPF, BGP and MPLS) with 1 year support. Stack
Module/40 Gig Optics and all other Cables should be included in Day 1. Approved Make : Cisco/
Impulse / Juniper / Extreme/ Arista
[54/80]
Page - 55
Bill of Quantities (BoQ)
[55/80]
Page - 56
Bill of Quantities (BoQ)
[56/80]
Page - 57
Bill of Quantities (BoQ)
Each incoming / outgoing breaker shall have microprocessor release with adjustable over
current, short circuit & earth fault protection with instantaneous as mentioned in specification.
The Panel will be made as per detailed specifications & drawings forming part of this document.
All the MCCB up to 250 Amp shall have thermal release with adjustable overload, short circuit &
earth fault protection and above shall have microprocessor release with adjustable overload,
short circuit & earthfault protection. The panel shall be manufactured as per BOQ, tech
specification and drawing.
INSTRUMENTS
3 Nos. 0 to 500 Volt digital voltmeter with builyin selector switch & Protective SP MCB (96mm
square) (one for each Incoming Breaker).
2 No. 0 to 1250 Amp digital ammeter (96mm square) with CT's & ASS (one for each 750 KVA
D.G. Set Incoming Breaker).
1 No. 0 to 800 Amp digital ammeter (96mm square) with CT's &ASS (one for each 500 KVA D.G.
Set Incoming Breaker).
3 Sets of phase indicating lights (RYB) with protection SP MCB's (one set for each incoming
924 INCOMMING / OUTGOING / BUSCOUPLER AIR CIRCUIT BREAKER: Each 1
Supplying with fitting and fixing panel mounting open execution 4 pole Air Circuit Breaker type
(MDO/EDO) with guide frame and 4 standard auxillary contacts in the existing cubical panel
board of the following capacity complete with making necessary connection as specified and
directed by the Dept. (ABB Emax/L & T U Power/ Siemens 3 WL/ Schneider Master pact NW)
6A trip system.
800A Breaking capacity @ Ics=50 KA (EDO)
[57/80]
Page - 58
Bill of Quantities (BoQ)
(Each Incoming / Outgoing MCCB shall have microprocessor release and variable current setting
from front, adjustable overcurrent, short circuit & earth fault protection, front extended lockable
handle, pad lockable in off position, shrouding on incomer side, termination shall be suitable for
aluminium bus bars / cables and as per specification.)
INSTRUMENTS
4 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB
(96mm square) (one for each Incoming Breaker).
4 No. 0 to 1600 Amp digital ammeter (96mm square) with CT's.
4 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker).
4 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).
4 Sets trip circuit healthy indicating lamp (one set for each incoming breaker).
4 Sets auto trip indicating lamp (one set for each incoming breaker).
928 INCOMMING / BUSCOUPLER AIR CIRCUIT BREAKER: Each 5
Supplying with fitting and fixing panel mounting open execution 4 pole Air Circuit Breaker type
(MDO/EDO) with guide frame and 4 standard auxillary contacts in the existing cubical panel
board of the following capacity complete with making necessary connection as specified and
directed by the Dept. (ABB Emax/L & T U Power/ Siemens 3 WL/ Schneider Master pact NW)
6A trip system.
1000A Breaking capacity @ Ics=50 KA (EDO)
929 1600A Breaking capacity @ Ics=50 KA (MDO) Each 5
930 OUTGOING MCCB: Each 6
4P MCCB with Microprocessor release (Adj Over Load, Short Ckt & neutral setting incl earth
protection)
Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with
microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, neutral
adjustable with earth fault protection without enclosure of the following capacity complete with
making necessary connection as approved, specified and directed by the dept.
36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make)
63A
931 50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) Each 4
100A
932 160A Each 3
933 250A Each 4
934 400A Each 2
935 630A Each 5
936 EXTERNAL LIGHTING PANEL (OUTDOOR TYPE)- Set 1
Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing &
commissioning of cubicle type totally enclosed free standing type moisture, dust and vermin
proof Floor Distribution Panel made out of 2.0 mm thick & front cover 1.6 mm thick CRCA sheet
complete with following equipments, including digital ammeter with inbuilt ammeter selector
switch, digital voltmeter with inbuilt voltmeter selector switch, indicating lamps, CT's, internal
wiring with suitable size wires / cable, interconnection, painting complete as per specification &
drawing.
INCOMING
1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.
1 No. 100 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
1 Set 24 Hrs TSQ Timer
1 Set 100 Amp, 4P Contactor & A/M switch and Push Button.
BUS BARS
100 Amp TPN aluminium busbar.
Panel described as above. (Incoming / Outgoing MCCB / MCB shall be paid separately. However
the fabrication cost for Incoming / Outgoing MCCB / MCB shall be included in above.)
[58/80]
Page - 59
Bill of Quantities (BoQ)
[59/80]
Page - 60
Bill of Quantities (BoQ)
944 Supply and laying of following size power / control copper cables, solid copper conductor, HLPE Meter 200.00
Insulated, cores laid up, PVC tape inner sheathed, unarmoured, extruded PVC ST2 sheathed,
650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct /
cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using
crimping tool and making good damaged done as specified and directed by the department.
(Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.)
Core-2, 2 XY
10.00 Sq.mm 2 Core Unarmoured U.G. Cable
951 Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006. Meter 25.00
[60/80]
Page - 61
Bill of Quantities (BoQ)
954 Supply, Installation, Testing & commissioning of Bollard Light 170 mm dia, 780 mm height made Each 20
out of cast aluminium lighting fixture, glass diffuser, stainless steel screw, extruded aluminium
poles, corrossion & UV resistant coation of 1 x 18 watt.
955 Supply, Installation, Testing & commissioning of Bollard Light 120 mm dia, 1000 mm height Each 15
made out of cast aluminium lighting fixture, glass diffuser, stainless steel screw, extruded
aluminium poles, corrossion & UV resistant coation of 1 x 18 watt.
956 Supply, Installation, Testing & Commissioning of LED street light fixture 40 watt, clour cool white Each 22
, integral driver, protection IP 65, CLASS I as complete as required. (Make Philips, Cat No-
BRP409 LED 040 CW HO MR FG S1 PSU GR or equivalent)
957 Supply, Installation, Testing & Commissioning of 1x21W Solar LED Lighting System consists of Each 10
PV Module, battery 12V, 100 Ah, grid charger unit, pole etc as per technical specification.
(Philips Make, Cat No - Philips BRP402 / 21W or equivalent).
958 Supply, Installation, Testing & commissioning of LED spike light. (Make-Philips, Cat No-BGP 310 Each 20
3XLED-HP/WW 220-240V 12 IN or equivalent).
959 SH: XIII: ACCESS CONTROL SYSTEM Nos 2
Supply, Installation, Testing & Commissioning of Motor power supply- 24V, Max. motor current-
12A, Motor power- 350 W, Max. torque- 750 nm, Max. boom length- 6250mm Max opening-
100deg, Max opening- 6 sec, Protection level- IP54, Weight- 50 kg as complete as required.
960 Supply, Installation, Testing, Commissioning of microprocessor based control panel having LED Set 6
indicators and audio buzzer, with 125khz hgh security format 2 door controller suitable for 4
readers including management software. (The controller shall be compatible for hardware
integration with fire alarm panel.)
961 Supply, Installation, Testing, Commissioning of 3"-4" read range proximity reader having LED Nos 12
indicators, with 125khz hgh security format. Power requirements 5-16V DC.
962 Supply of an Emergency Key. Nos 1
963 Supply, Installation, Testing, Commissioning of 600Lbs suitable for Single Leaf Door Nos 12
Electromagnetic Lock with magnetic contacts.
964 Supply, Installation, Testing, Commissioning of proximity card with 125 khz high security format . Nos 100
(HID Make.)
965 Supply, Laying of 0.75X 8 mm Multistand shielded copper tinned cable in an existing surface / Mtr 720.00
recessed conduit as required.
966 Supply, Installation, Testing, Commissioning of Exit Push Button Nos 12
967 SH: XIV: EARTHING Each 28
Supply with installation &commissioning of readymade maintenance free CPRI approved
chemical earthing system with 50 mm dia. 3.00 Meters length corrosion free dual pipe technology
G.I. CHEMRODE ELECTRODE Complete with raslow Grounding Minerals 25 k and Advance
Earth Pit cover including excavation of earth pit and construction brick earth chamber including
plastering both inner & outer surface of brick wall as specified and directed by the deptt.
968 Supply with installation &commissioning of readymade maintenance free CPRI approved Each 38
chemical earthing system with 50 mm dia. 3.00 Meters length corrosion free Single pipe
technology- Copper CHEMRODE ELECTRODE Complete with raslow Grounding Minerals 25 k
and Advance Earth Pit cover including excavation of earth pit and construction of brick earth
chamber including plastering both inner & outer surface of brick wall as specified and directed by
the deptt.
969 Supplying & laying of 6 SWG G.I. earth from EarthEletrode (below G.L.) to electrical switch gears Metre. 3410.00
or electrical machineries including making necessary connection as approved, specified and
directed by the deptt.
970 Supplying & laying of 25X6 mm size G.I. strips drawn on surface from earth electrode to Metre. 3040.00
Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc
including riveting, soldering & making necessary connection as approved, specified and directed
by the deptt.
[61/80]
Page - 62
Bill of Quantities (BoQ)
[62/80]
Page - 63
Bill of Quantities (BoQ)
[63/80]
Page - 64
Bill of Quantities (BoQ)
[64/80]
Page - 65
Bill of Quantities (BoQ)
[65/80]
Page - 66
Bill of Quantities (BoQ)
[66/80]
Page - 67
Bill of Quantities (BoQ)
1036 9,000 CFM, 60 mm St. Pr., 6 Row DX CC, 1 x 500 Dia Fan with 5.60 Kw Fan Motor IE-3 Rating, SET 2
Pre Filter, F/M Type, To be connected with 1x32 HP VRV / VRF ODU
1037 8,000 CFM, 70 mm St. Pr., 8 Row DX CC, 1 x 500 Dia Fan with 5.60 Kw Fan Motor IE-3 Rating, SET 2
Pre Filter, F/M Type, To be connected with 1x28 HP VRV / VRF ODU, Ducted Return
1038 Acoustically Insulated Box Type Inline Fans NO. 5
Supply, installation, testing and commissioning of single phase box type Inline fans with motor,
fire retardent double layer canvass connection etc complete in all respect & of following
capacities. The casing of inline fans shall be acoustically lined & shall be selected for lower noise
level. Fan motor shall have inbuilt speed controller.
100 CFM (8mm static pressure, single phase)
1039 300 CFM (8mm static pressure, single phase) NO. 2
1040 500 CFM (10mm static pressure, single phase) NO. 13
1041 750 CFM (10mm static pressure, single phase) NO. 10
1042 1000 CFM (15mm static pressure, single phase) NO. 5
1043 1500 CFM (20mm static pressure, single phase) NO. 3
1044 2500 CFM (20mm static pressure, single phase) NO. 2
1045 Plastic Propeller Fans NO 6
Supply, installation, testing and commissioning of propeller exhaust fans of various capacities
as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity
louvers & speed regulator etc.
Up to 125 CFM, 6 Inch Dia, 3 mm St. Pr.
1046 Above 125 CFM and Up to 250 CFM, 8 Inch Dia, 3 mm St. Pr. NO 2
1047 Above 250 CFM and Up to 500 CFM, 10 Inch Dia, 3 mm St. Pr. NO 2
1048 GI Propeller Fans NO 2
Supply, installation, testing and commissioning of GI propeller exhaust fans of various
capacities as given below suitable for 240 volts, 50 Hz, 900 RPM single phase AC supply
complete with gravity louvers & speed regulator etc.
750 CFM, 300 mm Dia, 3 mm St. Pr.
1049 1000 CFM, 380 mm Dia, 3 mm St. Pr. NO 2
1050 1500 CFM, 450 mm Dia, 3 mm St. Pr. NO 8
[67/80]
Page - 68
Bill of Quantities (BoQ)
[68/80]
Page - 69
Bill of Quantities (BoQ)
1083 For VRV / VRF Unit ODU for each module NO. 44
1084 Sub Head 'C' - HVAC Ducting & Grilles SMT 2325
Rectangular GI Ducting (Factory Made - L Shape)
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal
rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,
vanes, hangers, supports etc. as per approved drawings and specifications of following sheet
thickness complete as required.
24 G, Thickness 0.63 mm sheet (Up To 750 mm)
[69/80]
Page - 70
Bill of Quantities (BoQ)
1098 Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without SMT 28
volume control dampers complete as required.
1099 Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with SMT 30
aluminium volume control dampers with anti smudge ring & removable core.
1100 Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium SMT 20
without volume control dampers with anti smudge ring & removable core.
1101 Fresh / Exhaust air louvers with bird screen & damper SMT 13
1102 Volume control GI Dampers to be provided in supply & Exhaust air registers / terminals. SMT 15
1103 Fixed bar linear air register of following sizes RMT 130
100 mm
1104 125 mm RMT 135
1105 150 mm RMT 125
1106 Supply, installation and testing of GI Louvers constructed with casing in 14 G & louvers in 18 G SMT 45
construction for supply / exhaust air application for ventilation fan including bird screen, fixing
members, rain protector, free area of 55% etc as required to suit the site conditions.
1107 GSS Duct Damper SMT 65
Supply, installation, testing and commissioning of GI volume control duct damper complete with
neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. Back
draft damper / Non return damper etc shall be considered under this item only.
[70/80]
Page - 71
Bill of Quantities (BoQ)
1117 Fan Motor 2x Upto 3.73 Kw STP / Pump Room Ventilation NO. 2
Incomer
40 A TPN MCCB with (0-40A) ammeter with three CT and selector switch, (0 - 500 V)
voltmeter with selector switch, phase indication light with SP MCB. SET-01
Outgoing
a) For Fan Motor of Upto 3.73 Kw
32 A TPN MCCB with 16 A DOL starter, overload relay, start / stop push buttons, phase
indication lights with SP MCB, on / off / trip indication lights with SP MCB, single phase preventer
& auto / manual mode selector switch . SET-02
Controls & interlocking accessories as required for all the above panel shall be included in above
costing.
1118 Single Phase MCB for Inline Fan / Propeller Fan / VRV IDU NO. 254
Supply, Installation, testing & Commissioning of single phase MCB of following capacity:
6A / 10A / 16 A SP MCB, SET-01
[71/80]
Page - 72
Bill of Quantities (BoQ)
1148 Supplying & fixing of retro reflective sign board of size 1200 mm x 900 mm. The board made of Each 3
High intensity prismatic grade type IV retro reflective sheeting of 3M /Avery Denison or equivalent
make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film of same make
duly plotter cut, letters written (single side) in white colour, to be pasted on 3mm thick ACP sheet
of make Alstone / Alstrong / Eurobond / Alucobond or equivalent. Frame made of 40mm dia pipe
& 2nos. 63mm diavertical posts, 2.10 Mtr. high, all made of 304 series (Jindal or equivalent)
stainless steel. The pipe shall be standing on hard concrete surface with the help of SS holdfast/
Hilti or equallent flush anchor (Fasteners) of as per required size and numbers and thickness and
nut bolts on 02 Nos.5 mm thick 200mm x 200 mm size SS plate welded with 63mm dia SS pipe
as per direction of Unit Incharge.
1149 Supplying & fixing of retro reflective sign board of size 900 mm x 600 mm. The board made of Each 4
High intensity prismatic grade type IV retro reflective sheeting of 3M /Avery Denison or equivalent
make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film of same make
duly plotter cut, letters written (both side) in white colour, to be pasted on 3mm thick ACP sheet
of make Alstone / Alstrong / Eurobond / Alucobond or equivalent. Frame made of 38mm dia pipe
& 2nos. 63mm diavertical posts, 1.80 Mtr. high, all made of 304 series (Jindal or equivalent)
stainless steel. The pipe shall be standing on hard concrete surface with the help of SS holdfast/
Hilti or equallent flush anchor (Fasteners) of as per required size and numbers and thickness and
nut bolts on 02 Nos.5 mm thick 200mm x 200 mm size SS plate welded with 63mm dia SS pipe
as per direction of Unit Incharge.
[72/80]
Page - 73
Bill of Quantities (BoQ)
1154 Supply and fixing of Amuminium Silver powder coated signage of required size complete with SQ INCH 10000.00
message. Matter will be digital print written single sides, matter covered with transparent
polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/
double side tape of 3M make/ screw required nos of holes, wherever required complete as per
direction of Unit Incharge
1155 Supply and fixing of Amuminium Silver powder coated signage two plates ( vertical type) of SQ INCH 3000.00
required size complete with message. Matter will be digital print written both sides, matter
covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls
plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever
required complete as per direction of Unit Incharge
1156 Providing/Laying 2.5 mm thick road marking strips (Retro reflecting) oRoad marking paints with Sqm 300.00
applied thermo plastic compound with reflectorized glass beads on bituminous surface, providing
and laying of hot applied thermo plastic compound 2.5 mm thick including reflectorising glass
beads @ 250gm per sq. mtr. area thickness of 2.5 mm is exclusive of surface applied glass
beats as per IRC – 35. The finished surface should be level, uniform and free from streaks and
holes as per relevant clauses of section 800 in addition where arrows or letters are to be
provided thermo plastic compound may be hand sprayed. The colour of the compound shall be
white or yellow (IS Colour No. 356) as specified in the drawings or directed by the Unit Incharge.
15cm widths on bituminous surface/ Concrete, complete all as specified.
1157 Supply and installation of Raised pavement marker(RPM) with polycarbonate lens electronically Nos 100
welded with the RPM body. Marker shall be scratch proof and abrasion resistant micro prismatic
polycarbonate lens with polycarbonate Reflective panels with dual prismatic cubes capable of
providing total internal reflection. Dimensions: Dimensions of the marker is Height: 15.88
,Width: 101.6 ,Length: 89.2 .The marker conforms to ASTM D4280 and is in accordance with
MOSRTH Circular Ref No. RW/NH 33023/10/97-DO III Dated 11th June 1997. Markers shall be
fixed with adhesives and no nails shall be used to affix the marker and shall be marked with
manufacturers name, complete all as specified. Make 3M/ Avery Dennison C-8 Series/Simsonite
or equallent
1158 Providing & fixing of emergency sign boards single side of required size made of Photo Sq Inch 20000.00
luminescent film having glow power of 4 hours with message and graphics to be screen printing /
vinyl cut film of 3M / Avery Denison / LG / Oracle or equivalent make to be pasted on 3mm thick
Sun Board sheet all complete and duly fixed with required numbers of rawls plugs stainless steel
srew/ double side tape of 3M make required nos of holes, wherever required complete as per
direction of Unit Incharge
1159 Supply & Fixing Display notice pin up board or white writing board of required size, aluminum Sq Ft 600.00
beeding of 12 mm and fixed with required numbers of rawls plugs stainless steel srew as per
direction of Unit Incharge.
1160 Supply & Fixing Key ring holder stand of size 900mm x 600mm. Front door covered with Each 8
transparent acrylic sheet and locking arrangement. Fixed with required numbers of rawls plugs
stainless steel srew as per direction of Unit Incharge.
[73/80]
Page - 74
Bill of Quantities (BoQ)
[74/80]
Page - 75
Bill of Quantities (BoQ)
[75/80]
Page - 76
Bill of Quantities (BoQ)
1190 Supply, Installation, testing & commissioning of Projection lens having Throw distance of 20 to Nos. 1
30 mtr.
Approved Make: Christie / Barco / Digital Projection
Christie Lens Std Zm 1.7-2.6/1.6-2.4
1191 Supply, Installation, testing & commissioning of Mounting/hanging arrangement of above Nos. 1
Projector.
Approved Make: Custom
1192 Supply, Installation, testing & commissioning of 240-250" diagonal motorized projection screen Nos. 1
with aspect ratio 16:9.
Approved Make: Suvira / Draper / Liberty
Suvira
1193 Supply, installation, testing & Commissioning of Multi-Format transmitter model with 1 HDMI,1 Nos. 2
VGA-Audio input over a single CATx cable. Shall function as Quick switch technology with Last-
Connected mode. Supports resolutions upto HD for a distance of 90m.
Approved Make: Crestron/Extron/Kramer
Crestron DM-TX-200-C-2G
1194 Supply, installation, testing & Commissioning of 6x2 matrix switcher with Quick switch Nos. 1
technology. HDMI input signal with Deep color, and 4K support. Output on 1 nos CaTx and 1 nos
HDMI scaled. Outout HDMI should be 4K up-scaled with content-adaptive noise reduction, and
widescreen format selection. Should have 512MB RAM and 4GB of flash memory. Should have
at least 2x RS-232, 4x IR & 4x Relays. Device to have DHCP, HDCP 2.2.
Approved Make: Crestron/Extron/Kramer
Crestron DMPS3-4K-200-C
1195 Supply, installation, testing & Commissioning of HDMI Receiver over Twisted Pair, supports Nos. 1
cable length up to 90 mtrs for UHD/4K resolution, supports 4K resolution, IR, RS-232 and
Ethernet Control.
Approved Make: Crestron/Extron/Kramer
Crestron DM-RMC-4K-100-C
1196 Supply, installation, testing & Commissioning of HDMI Extender (Transmitter Receiver Pair Kit). Nos. 1
Approved Make: Crestron/Extron/Kramer
Crestron HD-EXT4-C
1197 Supply, installation, testing & Commissioning of 7.5” Touch Screen with Capacitive touch screen Nos. 1
technology, 960 x 540 qHD resolution, 16:9 aspect ratio, 400 nits (cd/m²) brightness, 750:1
contrast ratio, 24‐bit, 16.7M colors color depth, ±80°H, ±80°V viewing angle, Built‐in 5 MP H.264
IP camera, microphone and speakers, supports H.264 or MJPEG streaming video display.
Approved Make: Crestron/Extron/Kramer
Crestron TSW 760
1198 Supply, installation, testing & Commissioning of Table top kit for Touch Panel. Nos. 1
Approved Make: Crestron/Extron/Kramer
Crestron TSW-ttk
1199 Supply, installation, testing & Commissioning of Power over Ethernet adaptor for Touch panel. Nos. 1
Approved Make: Crestron/Extron/Kramer
Crestron PWE-4803 RU
1200 Supply, installation, testing & Commissioning of programmable 12 button panel for Automation. Nos. 1
Approved Make: Crestron/Extron/Kramer
Crestron CNX-B12B
1201 Supply, installation, testing & Commissioning of IR Probe for device control. Nos. 2
Approved Make: Crestron/Extron/Kramer
Crestron IRP2
1202 Supply, installation, testing & Commissioning of 802.11b/g/n compatible wireless access point, 3- Nos. 1
5W or better Antenna.
Approved Make: CISCO/Netgear / D-Link
Cisco / LinksysWAP
[76/80]
Page - 77
Bill of Quantities (BoQ)
1215 Supply , installation , testing and commissioning of custom VGA-HDMI Input wall plate Nos. 5
Approved Make: Custom
Logic WP-VGA-HDMI
1216 Supply , installation , testing and commissioning of 1:2 HDMI Distribution amplifier with Audio De- Nos. 5
embedder,
Approved Make: Crestron / Extron / Kramer
Crestron HD-DA2
1217 Supply, Installation, testing and commissioning of wall mount bracket for the Display panel Nos 5
complete with standard accessories as required.
Approved Make: Custom
[77/80]
Page - 78
Bill of Quantities (BoQ)
1222 Supply, installation, testing & Commissioning of Class D configurable amplifier with total 600W Nos 1
output power or better across 4 outputs, 4/8ohms, 70/100 Volt or mixed use operation;
Frequency Response : 20Hz - 20kHz for LZ mode ; S/N Ratio > 99db and THD <.3% at rated
output complete with standard accessories as required. Built in DSP for Matrix routing, Speaker
EQs, delays etc.
Approved Make: Bose / Labgrupen / Powesoft
Bose PS 604
1223 Supply , installation , testing and commissioning of 2 core 2.5 sq mm PVC insulated Cu Mtr. 200.00
conduction loudspeaker cable with Conductor 50 x 0.25 mm, Impedance 7.0 Ω/km Capacitance
170 pF/m, Outer dia 8.0 mm, working temperature -20 °C / +70 °C.
Approved Make: Belden / Klotz / Canare
Klotz
LY 225
1224 Supply , installation , testing and commissioning of 5,300 ISO lumens, WUXGA resolution and Nos 1
3,000,000:1 on/off contrast ratio Complete with standard accessories as per tender specification.
Approved Make: Christie / Barco / Digital projection
Christie LWU 530 APS
1225 Supply ,installation ,testing and commissioning of 16:10, 120-135" motorised projection screen Nos 1
with IR remote and low Voltage Control Module complete with standard accessories as per
tender specifications.
Approved Make: Suvira / Liberty / draper
Suvira 120" (16:9)
1226 Supply, installation, testing & Commissioning of Full High Definition Video Nos 1
Conferencing System Full HD 1080p Point to point Video conferencing with 12X optical zoom
full HD integrated camera, RF remote control and 1 No. omni directional microphone as per
tender specs.
Approved Make: Cisco / Polycom / Sony
Sony PCS-XG100
1227 Supply, installation, testing & Commissioning of HD MCU Plus Multipoint Software Option Nos 1
License. Allows for 9 (1+8) site MP video calls. Available for FHD.
Approved Make: Cisco / Polycom / Sony
Sony PCSA-MCG109
1228 Supply ,installation ,testing and commissioning of 7" A space-saving wall, lectern, tabletop, or Nos 1
rack mount touch screen featuring a clean, contemporary appearance with edge-to-edge glass
Touch panel to control all the controls provided in system for hassel free operation complete with
standard accessories as per tender specifications.
Approved Make: Crestron / Extron / Kramer
Crestron TSW 760 with brackets
1229 Supply ,installation ,testing and commissioning of Twisted Pair receiver . Input - Twisted Pair, Nos 1
Output - HDMI, Resolution support UPTO 4K, 4:4:4 @ 30Hz, Distance of Transmission
Minimum 50 meters for 4K, Controls 1 Ethernet, 1 RS232, Should be compatible. With HDCP
and EDID complete with standard accessories as per tender specifications.
Approved Make: Crestron / Extron / Kramer
Crestron DM-RMC-4K-100-C
[78/80]
Page - 79
Bill of Quantities (BoQ)
1232 9x4 matrix switcher with Quick switch technology. HDMI input signal with Deep color, and 4K Nos 1
support. Output on 2 nos CaTx and 2 nos HDMI scaled. Outout HDMI should be 4K up-scaled
with content-adaptive noise reduction, and widescreen format selection. Device should have in-
built control processor. Should have 512MB RAM and 4GB of flash memory. Should have at
least 2x RS-232, 4x IR & 4x Relays. Device to haveDHCP, H.264 decoding, MJPEG decoding,
HDCP 2.2.
Approved Make: Crestron/Extron/Kramer
DMPS-4K-350-C
1233 Supply , installation , testing and commissioning of Microphone control unit/processor for Nos 1
Connection of microphone units in two lines or a ring using standard computer Cat5e cables . A
maximum of 100 microphone unit can be connected (50 per line) without redundancy or a
maximum of 50 microphone units in a ring with redundancy for maximum as per the tender
specifications.
Approved Make: Beyer dynamic / brahler / marconi technologies
Beyer dynamics Orbis CU
1234 Supply , installation , testing and commissioning of Delegate Unit with a soft touch button with Nos 18
tactile feedback for turning the microphone on/off for conferencing system complete with
standard accessories as per tender specification.
Approved Make: Beyer dynamic / brahler / marconi technologies
BeyerdynamicsMU41
1235 Supply , installation , testing and commissioning of chairman Unit for conferencing system. the Nos 1
microphone unit shall be provided with three soft touch buttons with tactile feedback for turning
the microphone on/off, for clearing
all active delegate microphone units and for the priority as per the tender specifications.
Approved Make: Beyer dynamic / brahler / marconi technologies
BeyerdynamicsMU43
1236 Supply , installation , testing and commissioning of 16 Inch condenser gooseneck microphone Nos 19
(electret) with cardioid polar pattern The two flexible goosenecks (8 mm bottom, 6 mm top) shall
have a rigid tube in between Pressure gradient Frequency response Close miking: 40 - 13,000
Hz Distant miking (distance 1 m): 200 - 13,000 Hz.
Approved Make: Beyer dynamic / brahler / marconi technologies
Beyer dynamic Classis GM115Q
1237 Supply , installation , testing and commissioning of System cable CAT5 with RJ45 Connector 2m Nos 18
as per the tender specifications.
Approved Make: Beyer dynamic / brahler / marconi technologies
Beyer dynamics OC2
1238 Supply , installation , testing and commissioning of System cable CAT5 with RJ45 Connector Nos 2
20m as per the tender specifications.
Approved Make: Beyer dynamic / brahler / marconi technologies
Beyer dynamics OC20
1239 Supply , installation , testing and commissioning of 16 Inch condenser gooseneck microphone Nos 19
(electret) with cardioid polar pattern The two flexible goosenecks (8 mm bottom, 6 mm top) shall
have a rigid tube in between Pressure gradient Frequency response Close miking: 40 - 13,000
Hz Distant miking (distance 1 m): 200 - 13,000 Hz as per the tender specifications.
Approved Make: Beyer dynamic / brahler / marconi technologies
Beyer dynamics Classis GM 115Q
1240 Supply of 802.11b/g/n compatible wireless access point, 3-5W or better Antenna. Nos 1
Approved Make: CISCO/Netgear / D-Link
Cisco / LinksysWAP
1241 Supply of LIII managed Gigabit switch with at least 8-10 copper ports. Nos 1
Approved Make: CISCO/Netgear / D-Link
Cisco / Linksys 8-10 Port network Switch
1242 Supply , installation , testing and commissioning of VGA Micro HR with Audio Cable: 15-pin HD Nos 4
Male to Male Low-Profile Molded + 3.5mm Stereo Mini Plug Male to Male - 6' (1.8 m) complete
with standard accessories as per tender specifications.
Approved Make: AMX / Crestron / Extron
Crestron CBL-VGA-AUD-6
1243 Supply , installation , testing and commissioning of 4K Premium High Speed HDMI Ultra-Flexible Nos 8
Cable - 6' (1.8 m) complete with standard accessories as per tender specifications.
Approved Make: AMX / Crestron / Extron
Crestron CBL-HD-6
1244 Supply , installation , testing and commissioning of Shielded Digital Twisted Pair Cable for XTP Mtrs 150.00
& DTP products - Non-Plenum, 1000' (305 m) spool complete with standard accessories as per
tender specifications.
Approved Make: AMX / Crestron / Extron
Crestron DM-CBL-8G-NP-SP
[79/80]
Page - 80
Bill of Quantities (BoQ)
[80/80]