Professional Documents
Culture Documents
8 Supplying and Filling in plinth with local sand and under Cum 396.738
floors including watering, ramming consolidating and dressing
complete.
14 Providing and laying damp-proof course 50mm thick with Sqm 48.688
cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded
stone aggregate 20mm nominal size).
15 Extra for providing and mixing water profing material in per 50 kg 15.580
cement concrete work in the proportion recommended by the cement
manufacturers.
All works above plinth level upto floor V level cum 302.113
18 Add for using extra cement in the items of design mix over quintal 334.689
and above the
specified cement content therein.
Small lintels not exceeding 1.5m clear span, moulding as in Sqm 285.680
cornices, window sills, string courses, bands, copings, bed
plates, anchor blocks and the like.
Suspended floors, roots, laning, beams and balconies (Plan sqm 23.465
area to be measured)
25 Brick work 7 cm thick with common burnt clay F.P.S. (non sqm 37.222
modular) brick of class designation 7.5 in cement mortar 1:3
(1 cement : 3 coarse sand) in superstructure above plinth level
and upto floor five level.
28 Extra for providing and placing in position 2 nos. 6mm dia, sqm 513.001
MS bars at every third course of half brick masonry
29 Brick edging 7cm wide 11.4 cm deep to plinth protection with metre 110.430
common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 including grouting with cement mortar 1:4 (1
cement : 4 fine sand).
32 Extra for cutting rebate in flush door shutters (Total area of sqm 9.318
the shutter to be measured).
34 Providing 40x5 mm flat iron hold fast 40 cm long including each 138.000
fixing to frame with 10 mm diameter bolts, nuts and wooden
plugs and embedding in cement concrete block 30x10x15cm
1:3:6 mix (1 cement : 3 coarse sand: 6 graded stone aggregate
20mm nominal size).
Sl No Description Unit Quantity Rate Amount
35 Providing and fixing factory made P.V.C. door frame of size metre 176.600
50x47 mm with a wall thickness of 5 mm, made out of
extruded 5mm rigid PVC foam sheet, mitred at corners and
joined with 2 Nos of 150 mm long brackets of 15x15 mm
M.S. square tube, the vertical door frame profiles to be
reinforced with 19x19 mm M.S. square tube of 19 gauge,
EPDM rubber gasket weather seal to be provided through out
the frame. The door frame to be fixed to the wall using M.S.
screws of 65/100 mm size, complete as per manufacturer’s
specification and direction of Engineerin-Charge.
36 Providing and fixing factory made panel PVC door shutter
consisting of frame made out of M.S. tubes of 19 gauge
thickness and size of 19 mm x 19 mm for styles and 15x15
mm for top & bottom rails. M.S. frame shall have a coat of
steel primers of approved make and manufacture. M.S. frame
covered with 5 mm thick heat moulded PVC ‘C’ channel of
size 30 mm thickness, 70 mm width out of which 50 mm shall
be flat and 20 mm shall be tapered in 45 degree angle on both
side forming styles and 5 mm thick, 95 mm wide PVC sheet
out of which 75 mm shall be flat and 20 mm shall be tapered
in 45 degree on the inner side to form top and bottom rail and
115 mm wide PVC sheet out of which 75 mm shall be flat and
20 mm shall be tapered on both sides to form lock rail.
Top, bottom and lock rails shall be provided both side of the
panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet
be provided as gap insert for top rail & bottom rail, paneling
of 5 mm thick both side PVC sheet to be fitted in the M.S.
frame welded/ sealed to the styles & rails with 7 mm (5 mm+2
mm) thick x 15 mm wide PVC sheet beading on inner side,
and joined together with solvent cement adhesive. An
additional 5 mm thick PVC strip of 20 mm width is to be stuck
on the interior side of the ‘C’ Channel using PVC solvent
adhesive etc. complete as per direction of Engineer-in-charge,
manufacturer’s specification & drawing.
Sl No Description Unit Quantity Rate Amount
42 Providing and fixing bright finished brass 100mm mortice Each 12.000
latch and lock with six levers and a pair of anodised (anodic
coating not less than grade AC 10 as per IS:1868) aluminium
lever handles with necessary screws etc. complete (Best make
of approved quality).
43 Providing and fixing aluminium tee channels (heavy duty) Each 107.900
with rollers & stop end in pelmets as curtain rod.
Sl No Description Unit Quantity Rate Amount
With glass panes of 4.0mm thickness (weight not less than Sqm 91.646
10.0 kg/sqm)
With glass panes of 5.50 mm thickness(weight not less thar Sqm 2.770
13.75 kg/sqm)
49 Providing and fixing 100mm brass locks (best make of Each 1.000
approved quality) for aluminium doors including necessary
cutting and making good etc. complete.
52 Providing and fixing circular/ Hexagonal cast iron or M.S. Each 50.000
sheet box for ceiling fan clamp, of internal dia 140 mm, 73
mm height, top lid of 1.5 mm thick M.S. sheet with its top
surface hacked for proper bonding, top lid shall be screwed
into the cast iron/ M.S. sheet box by means of 3.3 mm dia
round headed screws, one lock at the corners. Clamp shall be
made of 12 mm dia M.S. bar bent to shape as per standard
drawing.
53 Steel work welded in built up sections/framed worK including
cutting hoisting, rixing in position and applying a priming coat
of approved steel primer using structural steel, etc. as required
57 Providing and fixing Ist quality ceramic glazed wall tiles sqm 509.013
conforming to IS: 15622 (thickness to be specified by the
manufacturer), of approved make, in all colours, shades except
burgundy, bottle green, black of any size as approved by
Engineer-in-Charge, in skirting, risers of steps and dados, over
12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg per sqm,
including pointing in white cement mixed with pigment of
matching shade complete.
Sl No Description Unit Quantity Rate Amount
60 Kota stone slab flooring over 20mm (average) thick base laid
over and jointed with grey cement slurry mixed with pigment
to match the shade of the slab including rubbing and polishing
complete.
25mm thick sqm 725.656
Sl No Description Unit Quantity Rate Amount
61 Kota stone slab 25mm thick in risers of steps skirting. Dado sqm 94.386
& pillars laid on 12mm (average thick cement mortar 1:3( 1
cement: 3 coarse sand) and jointed with grey cement slurry
mixed with pigment to match the shade of the slab including
rubbing and polishing complete.
62 Extra for Kota stone / sand stone in treads of steps and risers sqm 51.153
using single up to 1.05 metre.length
66 Extra for providing opening of required size & shape for wash each 30.000
basins/kitchen sink in kitchen platform. Vanity counters and
similar location in marble/stone work including necessary
holes for pillar taps etc. including rubing and polishing of cut
edges etc. complete.
67 Providing designation 100A one brick flat soling joints filled sqm 683.291
with local sand including cost of watering, taxes, royalty all
complete as per building specification and direction of E/I.
With ready mixed red oxide zinc chromate yellow primer of sqm 207.984
approved brand and manufacture on steel galvanised iron/steel
works
76 Painting with synthetic enamel paint of approved brand and
manufacture of required colour to give an even shade:
Sl No Description Unit Quantity Rate Amount
Two or more coats on new work over an under coat of suitable sqm 352.500
shade with ordinary paint of approved brand and manufacture.
77 Forming groove of uniform size from 12x12 mm and upto Metre 322.290
25x15 mm in the top layer of washed stone grit plastered
surface as per approved pattern, including providing and
fixing aluminum channels of appropriate size and thickness
(not less than 2 mm), nailed to the under layer with rust proof
screws and nails and finishing the groove complete as per up
to 50 m and lift upto 1.5 m.
78 Providing and laying water proofing treatment to vertical and
horizontal surfaces of depressed portions of W.C., kitchen and
the like consisting
of:
Ist course of applying cement slurry @ 4.4 kg/sqm mixed with
water proofing compound conforming to IS 2645 in
recommended proportions including rounding off junction of
vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse
sand) mixed with water proofing compound in recommended
proportion including rounding off junction of vertical and
horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot
at 1.7 kg. per sqm of area.
IVth course of 400 micron thick PVC sheet. (Overlaps at sqm 170.624
joints of PVC sheet should be 100 mm wide and pasted to
each other with bitumen @ 1.7 kg/sqm).
Sl No Description Unit Quantity Rate Amount
BOUNDARY WALL
82 Earth work in excavation by mechanical means (Hydraulic
excavator) / manual means in foundation trenches or drains
(not exceeding 1.5 m in width or 10 sqm on plan), including
dressing of sides and ramming of bottoms, lift upto 1.5 m,
including getting out the excavated soil and disposal of
surplus excavated soil as directed, within a lead of 50 m.
85 Supplying and Filling in plinth with local sand and under Cum 14.418
floors including watering, ramming consolidating and dressing
complete.
86 Providing designation 100 A one brick flat soling joints filled sqm 160.314
with local sand including cost of watering , taxes , royalty as
per building specification of E/I ,
87 Providing and laying in position cement concrete of specified
grade excluding the cost of centering and shuttering-All work
up to plinth level:
1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 cum 11.039
mm nominal size)
All works above plinth level upto floor V level cum 14.139
90 Add for using extra cement in the items of design mix over quintal 51.529
and above the specified cement content therein.
Small lintels not exceeding 1.5 m clear span, mouldings as in Sqm 40.3
cornoces, window sills, string, courses, bands, copings, bed
plates, anchor blocks and the like.
Bricks 100A (only for brick flat soling work) %0 nos 31.316
PAVER
101 Supplying and Filling in plinth with local sand and under Cum 102.632
floors including watering, ramming consolidating and dressing
complete.
102 Providing and laying 60mm thick factory made cement sqm 684.215
concrete interlocking paver block of M -30 grade made by
block making machine with strong vibratory compaction, of
approved size, design & shape, laid in required colour and
pattern over and including 50mm thick compacted bed of
coarse sand, filling the joints with fine sand etc. all complete
as per
the direction of Engineer-in-charge.
103 Providing and laying at or near ground level factory made cum 16.825
kerb stone of M-25 grade cement concrete in position to the
required line, level and curvature, jointed with cement mortar
1:3 (1 cement: 3 coarse sand), including making joints with or
without grooves (thickness of joints except at sharp curve
shall not to more than 5mm), including making drainage
opening wherever required complete etc. as per direction of
Engineer-in-charge (length of finished kerb edging shall be
measured for payment). (Precast C.C. kerb stone shall be
approved by Engineer-in-charge).
PHE WORKS
A
104 Providing and fixing G.I. pipes complete with G.I. fittings
and clamps, i/c cutting and making good the wall etc.
Sl No Description Unit Quantity Rate Amount
105 Providing & fixing G.I. pipe complete with G.I. fittings
and clamps i/c making good the walls etc.concealed
pipe including painting with anti corrosive bitumatic
paint, cutting chases and making good the wall.
(A) Metre 143.00
25 to 40 mm Nominal bore
108
Providing and fixing brass stop cock of approved quality
(A) each 5.00
15 mm Nominal bore
20 mm Nominal bore
109 Providing and fixing brass gate valve with C.I. wheel of
approved quality.
Each. 6.00
25 mm Nominal bore
32 mm Nominal bore
40 mm Nominal bore
Each. 1.00
Horizontal
Each. 1.00
Vertical
113 Providing and placing on terrace (at all floor levels ) litre 10000.00
polythethylene water storage tank ,ISI-12701 marked
with cover and suitable locking arrangement and making
necessary holes for inlet, outlet and overflow pipes but
without fittings and the base support for tank
117 Providing and fixing C.P. brass angle valve for basin
mixer and geyser pointsof approved quality confirming
to8931
15 mm Nominal bore Each 6.00
150 mm diameter
B
Sl No Description Unit Quantity Rate Amount
Each 3.00
Each 28.00
124 Provding and fixing PVC waste pipe for sink or wash
basin including PVC waste fittings complete
Flexiable pipe
Each 36.00
40 mm dia
125 Provding and fixing 600X450mm bevelled edge mirror Each 32.00
of superior glass (of approved quality) complete with
6mm thick hard board ground fixed to wooden cleats
with CP brass screws & washers complete.
126 Provding and fixing 600X120X5 mm glass shelf with Each 32.00
edges rounded off supported on anodised aluminium
angle frame with CP brass brackets and guard rail
complete fixed with 40 mm long screws ,rawl plug etc,
complete.
127 Provding and fixing toilet paper holder
Vitreous china Each 3.00
Sl No Description Unit Quantity Rate Amount
128 Provding and fixing PTMT liquid soap container 109 Each 18.00
mm wide,125mm high and 112mm distance from wall of
standard shape with bracket of same materials with
snap fittings of approved quality and colour, weighing
not less than 105 gms.
129 Provding and fixing PTMT towel rail complete with
brackets fixed to wooden cleats with CP brass screws
with concealed fittings arrangement of approved quality
and colour.
600 mm long towel rail with total length of 645mm Each 18.00
110mm diameter
110mm
0
Bend 87.5
Sl No Description Unit Quantity Rate Amount
Each 10.00
110mm bend
Shoe (Plain)
Each 8.00
110mm Shoe
Each 60.00
110mm
133 Providing and fixing to the inlet mouth of rain water pipe Each 10.00
cast iron grating 15 cm diameter and weighing not less
than 440 grams.
C
1 Providing and laying non -pressure NP2 class(light duty)
R.C.C. pipes with collars jointed with stiff mixture of
cement mortar in the proportion of 1:2 including testing
of joints etc. complete
(A) Metr. 193.00
D
135 Earthwork in excavation by mechanical means (Hydraulic
excavator)/manual means in foundation trenches or drains (not
exceeding 1.5 m in width or 10 sqm on plan ) including dressing
of sides and ramming of bottoms,lift upto 1.5m,including getting
out the excavated soil and disposal of surplus excavated soil as
directed within a lead of 50m
Cum 48.88
136 Supplying and filling in plinth with jamuna sand and under floors Cum 2.03
including watering,ramming consolidating and dressing
complete
138 Brick work with common burnt clay FPS(non modular) bricks of
class designation 7.5 in foundations and plinth in
Cum 11.47
Cement morter 1:6(1 cement : 6 corse sand)
Kg 190.00
Thermo-Mechanically Treated bars
143 Supplying and fixing C.I cover without frame for manholes:
500 mm diameter C.I cover (medium duty) the weiht of he Each 2.00
cover to be not less than 58 kg.
144 Providing M.S foot rests including fixing in septic tank with 20 x
20 x 10 cm cement concrete blocks 1:3:6 ( 1 cement: 3 coarse
sand: 6 graded stone aggregate 20mm nominal size) as per
standard design:
With 20 x 20 mm square bar Each 18.00
151 Providing & fixing suitable size threaded mild steel cap or spot
welded plate to the top of borewell housing/ casing pipe
,removable as per requirement,all complete for borewell of,
153 Providing & fixing Bail plug/ bottom plug of required dia to the
bottom of pipe assembly as per IS;2800(part-I),
150 mm dia each 1
E
Sl No Description Unit Quantity Rate Amount
155
Provding and fixing soil,waste and vent pipes
110 mm dia metre 339.00
156
DOOR TEE
110 mm dia each 17.00
PLAIN BEND
110 mm dia each 6.00
DOOR BEND
110 mm dia each 24.00
BEND 45
110 mm dia each 56.00
VENT COWEL
Sl No Description Unit Quantity Rate Amount
PIPE CLIP
110 mm dia each 160.00
FLOOR TRAP
110X110 mm dia each 34.00
ELECTRICAL WORKS
WIRING
158 Wiring for Light plug & Light circuit with 2x1.5 sq.mm Meter 1020
FR PVC insulated copper conductor single core cable in
surface / recessed PVC conduit along with 1 No.1.5 sq
mm FR PVC insulated copper conductor single core
cable for loop earthing as required
159 Wiring for power plug with 2x4 sq.mm FR PVC insulated Meter 960
copper conductor single core cable in surface /
recessed PVC conduit along with 1 No.4 sq mm FR
PVC insulated copper conductor single core cable for
loop earthing as required
Sl No Description Unit Quantity Rate Amount
160 Wiring for submain with 4x6 sq.mm +2X6 sq mm earth Meter 200
wire FR PVC insulated copper conductor single core
cable in surface / recessed PVC conduit etc. as
required.
161 Wiring for submain with 4x10 sq.mm +2X10 sq mm Meter 200
earth wire FR PVC insulated copper conductor single
core cable in surface / recessed PVC conduit etc. as
required.
162 Wiring for submain with 2x6 sq.mm + 1X6 sq mm earth Meter 80
wire FR PVC insulated copper conductor single core
cable in surface / recessed PVC conduit etc. as
required.
163 Supplying & fixing following sizes PVC conduit along
with accessories in surface / recess including painting
in case of surface conduit or cuting of wall and making
good the same in case of recessed conduit as required.
(For Tele. TV & Lan. Cabling}
(a) 20 mm dia Meter 500
166 Wiring for light point/ fan point/ exhaust fan point / call Point 318
bell point with 1.5 Sq.mm FR PVC insulated copper
conductor cable in surface / recessed PVC conduit with
modular switch, modular plate, suitable GI box and
earthing the point with 1.5 sq mm FR PVC insulated
copper conductor single core cable etc as required.
167 Supplying and fixing modular type 5/6A switch and 3 Point 32
pin 5/6A socket on the existing switch box including
making connections etc. as required .
168 Supplying and fixing suitable size GI box with modular Point 7
plate and cover in front on surface or in recess
including providing and fixing 3 pin 5/6 amps moduler
socket outlet & 6A modular type switch connection etc.
as required.
169 Supplying and fixing suitable size GI box with modular Point 24
plate and cover in front on surface or in recess
including providing and fixing 6 pin 5/6 & 15/ 16 amps
moduler socket outlet & 15/16A modular type switch
connection etc. as required.
170 Supplying and fixing 20 amps 240 volt, SPN industrial Each 24
type, socket outlet, with 2 pole and earth metal enclosed
plug top along ,with 20 amp 'C' series, SP, MCB in sheet
steel enclosure on surface or in recess,with chained
metal cover for socket out let and complete with
connections testing and commissioning etc. as
required.
Sl No Description Unit Quantity Rate Amount
174 Supplying and drawing low resistance co-axial T.V cable Meter 90
RJ-6 grade 0.7mm solid copper conductor PE insulated
shielded with fine tinned copper braid and protected with
PVC sheath in the existing PVC concuit etc. as
required.
175 Supplying and fixing moduler type TV antenna socket Each 3
outlet on the existing box including making connection
etc. as required.
176 Supplying and fixing step type electronic fan regulator , Each 76
on the existing modular plate switch box including
making connection etc. as required.
188 Providing and fixing 4mm dia copper wire on surface or Meter 50
in recess for loop earthing etc as required.
INSTALLATION OF FIXTURES
189 Installation, testing and commissioning of ceiling fan Each 76
including wiring the down rod of standard length (upto
30cm) with 1.5 sq.mm FR PVC insulated copper
conductor, single core cable including providing and
fixing phenolic laminated sheet cover on the fan box
etc. as required.
190 Insatallation of exhaust fan upto 450mm sweep in the Each 14
exisiting opening, including making the opening to suit
the size of the above fan, making good the damage,
connection, testing, commisssiong etc. as required.
Sl No Description Unit Quantity Rate Amount
192 Erection of wall bracket / ceiling fittings of all sizes and Each 34
shapes containing upto two GLS lamps per fittings,
complete with all accessories including connections
etc.as required.
194 Supplying and fixing 3 pin 5 Amp ceiling rose on the Each 65
existing junction box/ PVC box including connection etc
as required.
SUPPLY OF FIXTURES
196 1200 mm sweep A.C. ceiling fan suitable for 250 volts Each 76
50 Hz complete Model Avancer Crompton Greaves
Make or equivalent approved make.
Sl No Description Unit Quantity Rate Amount
198 300 mm sweep A.C. Metalic Exhaust fan / freashair fan Each 9
of Model Trans Air -Crompton make Equivalent
approved make.
203 Bulk Head fitting Cat no NXC 101 of Philips Make Each 14
complete with glass cover, wire guard, lamp etc. as
required.
Sl No Description Unit Quantity Rate Amount
(a) Up to 35 sq mm M 15
212 Providing and laying NP2 (Non pressure) RCC pipe Meter 15
complete with RCC collar etc. as required of dia 150
mm.
COMPUTER NETWORK
215 Supplying of 2 Mtrs long patch cord with RJ 45 jacks on Meter 29
both end ( Make D Link).
EXTERNAL ELECTRICIFICATION
222 Supplying and erection of metallic 3.2mm thick 50mm Each 7
dia 3.66 meter height black tubular pole and base plate
225mm x 225mm x 6mm with primer and painting of
approved shade in cement concrete 1:3:6 ( graded
stone aggregate 40mm nominal size) foundation, nut
bolts, including excavation, refilling etc.as good as
required.
223 Supply & fitting of M.S cable end box of size 25cm x Each 11
20cm x 7.5cm with hinged lockable door including 6A
single pole MCB (Legrand make) and 63A connector
including clamp, nutt, bolt etc. as required.
Sl No Description Unit Quantity Rate Amount
224 S/F/F of post top lantern fitting Cat No. BJODCI 1170 Each 7
MH complete Bajaj or other equivalent make along with
lamp suitable for 250 volts 50HZ including proper
connection with 1.5 sq.mm PVC insulated copper
conductor wire testing and commissioning etc. as
required.
225 Supplyig fitting & fixing of post top lantern fitting Cat No. Each 4
BJODCI 150 MH Bajaj make or equivalent with lamp
suitable for 250 volts 50 HZ including nut, bolt,clamp,
with proper connection with 1.5 Sq.mm PVC insulated
copper conductor wire testing and commissioning etc.
as required.
226 Fabrication, supplying and erection 50 mm dia pipe of Each 4
approved shape for gate light complete as required
TOTAL