Professional Documents
Culture Documents
BAE
2 06.AUG.2014 ISSUED FOR CONSTRUCTION T.S.PARK J.Y.NA S.H.BAE
1 18.JUN.2014 ISSUED FOR CONSTRUCTION T.S.PARK J.Y.NA S.H.BAE
0 10.DEC.2013 ISSUED FOR CONSTRUCTION T.S.PARK J.Y.NA S.H.BAE
A 28.OCT.2013 ISSUED FOR INFORMATION T.S.PARK J.Y.NA S.H.BAE
REV. DATE DESCRIPTION DESIGNED CHECKED APPROVED
OWNER
PROJECT
ENGINEER
CONTRACTOR
N/A
DOCUMENT TITLE
TABLE OF CONTENTS
6. TYPE - F1 ………………………………… 19
7. TYPE - F2 ………………………………… 46
Page 2 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 3 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 4 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 5 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1. DESIGN CRITERIA
1.1 General
- ACI 318M-/318RM : General Concrete Design and Specification (American Concrete Institute)
- ASCE 7 : Design Load Combination (American Society of Civil Engineering)
- UBC 97 : Design seismic load (Uniform Building Code)
- Civil Design Criteria (10-TAA-C-35-001-001)
2) Material Property
- Soil
· Unit Weight γs = 18 kN/m³
- Coefficient of Friction
· Steel to Steel : 0.30
· Concrete to Soil : 0.40
Page 6 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Above values are the target soil bearing capacity after the completion of soil improvement
by stone column or dynamic replacement method.
- Structures, equipment, and foundations will be designed for the appropriate load combinations from ASCE 7-05,
and any other probable realistic combination of loads. The load combinations shown below are the most
common load combinations but may not cover all possible conditions.
Short term temporary loads such as temperature or test loads do not need to be combined with wind and seismic
loads unless load combination of hydro test is recommended by vendor.
It is not necessary to combine crane loads with wind or seismic loads when the purpose of crane use is the
maintenance of the equipment (Standby-service) in the structures only. Engineering judgment about load
combination of crane load and wind/seismic load will be made to structural design for each case.
Symbols and notation of load combinations are as follow:
Combinations D L F T H W E Lr
1) D+F 1.40 1.40
2) D + F + T + L + H + Lr 1.20 1.60 1.20 1.20 1.60 0.5
3) D + Lr + L 1.20 1.00 1.6
4) D + Lr ± W 1.20 0.80 1.6
5) D + W + L + Lr 1.20 1.00 1.60 0.5
6) D+E+L 1.20 1.00 1.00
7) D+W+H 0.90 1.60 1.60
8) D+E+H 0.90 1.60 1.00
2) Nominal Load Combinations for Allowable Stress Design and Foundation Stability Check
Combinations D L F T H W E Lr
1) D+F 1.00 1.00
2) D+H+F+L+T 1.00 1.00 1.00 1.00 1.00
3) D + H + F + Lr 1.00 1.00 1.00
4) D + H + F + L + T + Lr 1.00 0.75 1.00 0.75 1.00 1
5) D+H+F+W 1.00 1.00 1.00 1.00 0.75
6) D+H+F+E 1.00 1.00 1.00 0.70
7) D + H + F + W + L + Lr 1.00 0.75 1.00 1.00 0.75 0.75
8) D + H + F + E + L + Lr 1.00 0.75 1.00 1.00 0.525 0.75
9) D+W+H 0.60 1.00 1.00
10) D+E+H 0.60 1.00 0.70
Page 7 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2. GENERAL SKETCH
2.1 Plan
Page 8 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2.2 3D Modeling
Plan View
ISO View
Page 9 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
3. DESIGN LOAD
1) Self weight
- DC -
- DS -
Page 10 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
3) Soil Weight
Page 11 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Minimum Live Load (Refer. To Section 5.5 Live Load, Design Criteria Doc. No. 10-TTA-C-35-001-001.)
Page 12 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 13 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 14 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 15 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Ap x Ep 2827.44 x 287810
Kv = α × = 0.63 x
ℓ 1500
= 339068.17 kgf/cm
= 33907.00 tonf/m/EA = 339070.00 kN/m/EA
Page 16 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Kh = 1+E10 kN/m3
Page 17 of 569
``
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
5. LOAD COMBINATION
- Description
Dead : Foundatoin Self Weight + Upper Structure Dead Load
Live : Floor Live Load + Upper Structure Live Load
Seismic : Seismic Load
Wind : Wind Load
Temp : Temperature Load
Page 18 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
6. TYPE - F1
4500
1750
5500
2000
500
1750
700
150
5700
800
4500
Page 19 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 20 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 21 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 22 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 23 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
61.93
Page 24 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Min.)
X
Z
Value
(kN·m/m)
95.75
Page 25 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Max.)
X
Z
Value
(kN·m/m)
93.15
Page 26 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Min.)
X
Z
Value
(kN·m/m)
121.03
Page 27 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
X
Z
Value
(kN/m)
252.51
Page 28 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
X
Z
Value
(kN/m)
295.92
Page 29 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Max.)
X
Z
Value
(kN·m/m)
37.98
Page 30 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Min.)
X
Z
Value
(kN·m/m)
56.56
Page 31 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Max.)
X
Z
Value
(kN·m/m)
75.12
Page 32 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Min.)
X
Z
Value
(kN·m/m)
73.13
Page 33 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
Page 34 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.08 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 35 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0005
Page 36 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.16 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 37 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0005
Page 38 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.12 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 39 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
Page 40 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.15 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 41 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1. 500 X 700
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I -70.816 9.800 0.924 -11.831 57.330
ULC01
J -142.478 9.800 0.924 -6.426 0.000
I -149.211 42.380 1.536 -19.710 247.923
ULC02
J -210.636 42.380 1.536 -10.724 0.000
I -151.995 9.676 2.160 -27.584 -56.605
ULC03
J -213.420 9.676 2.160 -14.948 0.000
I -116.889 13.370 1.452 -18.582 78.215
ULC04
J -178.314 13.370 1.452 -10.088 0.000
I -60.699 8.400 0.792 -10.141 49.140
ULC05
J -122.124 8.400 0.792 -5.508 0.000
I -288.171 35.888 0.856 -10.980 209.945
ULC06
J -349.596 35.888 0.856 -5.972 0.000
I -116.889 13.370 1.452 -18.582 78.215
ULC07
J -178.314 13.370 1.452 -10.088 0.000
I -571.833 68.346 1.580 -20.259 399.824
ULC08
J -633.258 68.346 1.580 -11.016 0.000
I -124.359 14.060 5.812 -72.038 82.251
ULC09
J -185.784 14.060 5.812 -38.038 0.000
I -198.559 23.160 1.472 -18.859 135.486
ULC10
J -259.984 23.160 1.472 -10.248 0.000
I -7.688 4.590 0.405 -5.186 26.852
ULC11
J -53.757 4.590 0.405 -2.817 0.000
I -462.632 59.566 0.533 -6.863 348.461
ULC12
J -508.701 59.566 0.533 -3.745 0.000
I -15.158 5.280 4.765 -58.642 30.888
ULC13
J -61.227 5.280 4.765 -30.767 0.000
I -89.358 14.380 0.425 -5.463 84.123
ULC14
J -135.427 14.380 0.425 -2.977 0.000
Pu max -7.688 68.346 5.812 -5.186 26.852
Pu min -633.258 68.346 5.812 -11.016 0.000
Applied Loads
Mux max -124.359 68.346 5.812 -72.038 82.251
Muy max -571.833 68.346 5.812 -20.259 399.824
- Description
I : Pedestal Lower
J : Pedestal Top
Page 42 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Rebar Design
Page 43 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
h1 = 80.00 cm = 800.00 mm
PB = 0.50 m = 500.00 mm PL = 0.70 m = 700.00 mm
359
500
359
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 7162120.47 N = 7162.12 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 10718584.58 N = 10718.58 kN
ΦVc = 0.75 x 0.33 x fck x b0 x d
= 5724739.89 N = 5724.74 kN
βC = 1.40 : Ratio of long side to short side of concentrated load or reaction area
bO = 5268 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
Page 44 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 45 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
7. TYPE - F2
600
500
400
2000
3000
500
3000
150
1000
500
3000
Page 46 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 47 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 48 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 49 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 50 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 51 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
22.30
Page 52 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Min.)
X
Z
Value
(kN·m/m)
49.01
Page 53 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Max.)
X
Z
Value
(kN·m/m)
52.24
Page 54 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Min.)
X
Z
Value
(kN·m/m)
29.16
Page 55 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
X
Z
Value
(kN/m)
188.56
Page 56 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
X
Z
Value
(kN/m)
114.25
Page 57 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Max.)
X
Z
Value
(kN·m/m)
11.72
Page 58 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Min.)
X
Z
Value
(kN·m/m)
31.03
Page 59 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Max.)
X
Z
Value
(kN·m/m)
39.11
Page 60 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Min.)
X
Z
Value
(kN·m/m)
16.84
Page 61 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
Page 62 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.04 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 63 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0008
Page 64 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.15 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 65 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
Page 66 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.12 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 67 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0005
Page 68 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.06 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 69 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1. 400 X 600
2) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I -51.842 7.504 0.028 -6.492 8.630
ULC01
J -61.502 7.504 0.028 -6.524 0.000
I -157.788 40.940 3.540 -33.583 47.081
ULC02
J -166.068 40.940 3.540 -29.512 0.000
I -157.740 14.668 3.108 6.606 -16.868
ULC03
J -166.020 14.668 3.108 3.032 0.000
I -115.266 10.622 0.126 -10.517 12.215
ULC04
J -123.546 10.622 0.126 -10.372 0.000
I -44.436 6.432 0.024 -5.564 7.397
ULC05
J -52.716 6.432 0.024 -5.592 0.000
I -137.300 21.888 0.640 -7.896 25.171
ULC06
J -145.580 21.888 0.640 -7.160 0.000
I -115.266 10.622 0.126 -10.517 12.215
ULC07
J -123.546 10.622 0.126 -10.372 0.000
I -300.994 41.534 1.454 -15.180 47.764
ULC08
J -309.274 41.534 1.454 -13.508 0.000
I -121.206 11.272 6.446 -47.425 12.963
ULC09
J -129.486 11.272 6.446 -40.012 0.000
I -150.896 16.532 0.306 -11.014 19.012
ULC10
J -159.176 16.532 0.306 -10.662 0.000
I -33.606 3.636 0.414 -1.783 4.181
ULC11
J -39.816 3.636 0.414 -2.259 0.000
I -219.334 34.548 0.914 -6.446 39.730
ULC12
J -225.544 34.548 0.914 -5.395 0.000
I -39.546 4.286 5.906 -38.691 4.929
ULC13
J -45.756 4.286 5.906 -31.899 0.000
I -69.236 9.546 0.234 -2.280 10.978
ULC14
J -75.446 9.546 0.234 -2.549 0.000
Pu max -33.606 41.534 6.446 -1.783 4.181
Pu min -309.274 41.534 6.446 -13.508 0.000
Applied Loads
Mux max -121.206 41.534 6.446 -47.425 12.963
Muy max -300.994 41.534 6.446 -15.180 47.764
- Description
I : Pedestal Lower
J : Pedestal Top
Page 70 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Rebar Design
Page 71 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
209
400
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 2786557.35 N = 2786.56 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3817611.41 N = 3817.61 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2318228.38 N = 2318.23 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3668 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
Page 72 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 73 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1800
600
1800
400
150
1000
350
1800
Page 74 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Unit : kN·m
Node Load Case FX FY FZ MX MY
Con'c self weight 0.00 0.00 58.05 0.00 0.00
Dead Soil Weight 0.00 0.00 54.00 0.00 0.00
Rack Dead 15.42 7.79 91.93 0.00 22.63
Surcharge 0.00 0.00 15.00 0.00 0.00
Live LL 6.24 9.57 87.21 0.00 8.66
Sub Total 6.24 9.57 102.21 0.00 8.66
MD#1-2
X 0.00 0.00 0.00 0.00 0.00
Wind
Y 2.17 16.27 52.85 0.00 2.99
X 14.63 -2.22 -21.38 0.00 37.87
Seismic
Y 1.74 10.64 33.02 0.00 2.44
+ -0.98 21.57 0.00 0.00 -2.49
Temp
- 0.98 -21.57 0.00 0.00 2.49
Page 75 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 76 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 77 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
Page 78 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
32.31
Page 79 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Min.)
X
Z
Value
(kN·m/m)
12.62
Page 80 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Max.)
X
Z
Value
(kN·m/m)
32.98
Page 81 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Min.)
X
Z
Value
(kN·m/m)
8.18
Page 82 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
X
Z
Value
(kN/m)
106.29
Page 83 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
X
Z
Value
(kN/m)
93.18
Page 84 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Max.)
X
Z
Value
(kN·m/m)
22.87
Page 85 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Mxx (Min.)
X
Z
Value
(kN·m/m)
8.81
Page 86 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Max.)
X
Z
Value
(kN·m/m)
23.83
Page 87 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- Myy (Min.)
X
Z
Value
(kN·m/m)
5.83
Page 88 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0012
Page 89 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.14 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 90 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0012
Page 91 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.15 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 92 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0005
Page 93 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.06 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 94 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
Page 95 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.04 mm < Wa ( 0.30 ) mm ∴ O.K !
Page 96 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 130.774 9.604 18.816 47.692 11.045
ULC01
J 121.114 9.604 18.816 26.054 0.000
I 251.628 49.428 24.888 61.741 56.842
ULC02
J 243.348 49.428 24.888 33.120 0.000
I 251.628 2.340 27.240 70.422 -2.691
ULC03
J 243.348 2.340 27.240 39.096 0.000
I 199.302 17.802 22.338 56.631 20.472
ULC04
J 191.022 17.802 22.338 30.942 0.000
I 112.092 8.232 16.128 40.879 9.467
ULC05
J 103.812 8.232 16.128 22.332 0.000
I 83.636 3.528 16.008 40.581 -4.057
ULC06
J 75.356 3.528 16.008 22.172 0.000
I 199.302 17.802 22.338 56.631 20.472
ULC07
J 191.022 17.802 22.338 30.942 0.000
I 142.390 5.718 22.098 56.035 -6.576
ULC08
J 134.110 5.718 22.098 30.622 0.000
I 182.042 16.032 34.958 103.734 18.437
ULC09
J 173.762 16.032 34.958 63.532 0.000
I 171.522 8.632 21.018 53.293 9.927
ULC10
J 163.242 8.632 21.018 29.122 0.000
I 43.974 3.771 3.735 9.479 4.337
ULC11
J 37.764 3.771 3.735 5.184 0.000
I -12.938 19.749 3.495 8.883 -22.711
ULC12
J -19.148 19.749 3.495 4.864 0.000
I 26.714 2.001 16.355 56.582 2.301
ULC13
J 20.504 2.001 16.355 37.774 0.000
I 16.194 5.399 2.415 6.141 -6.209
ULC14
J 9.984 5.399 2.415 3.364 0.000
Pu max 251.628 49.428 34.958 61.741 56.842
Pu min -19.148 49.428 34.958 4.864 0.000
Applied Loads
Mux max 182.042 49.428 34.958 103.734 18.437
Muy max 251.628 49.428 34.958 61.741 56.842
- Description
I : Pedestal Lower
J : Pedestal Top
Page 97 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
2) Rebar Design
Page 98 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
h1 = 35.00 cm = 350.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
134
400
134
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 1492344.95 N = 1492.34 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 1711547.47 N = 1711.55 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 1241530.67 N = 1241.53 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3068 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
Page 99 of 569
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
9. TYPE - F4
1700
750
3700
2200
400
750
600
150
1000
500
1700
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
19.50
- Mxx (Min.)
X
Z
Value
(kN·m/m)
83.87
- Myy (Max.)
X
Z
Value
(kN·m/m)
21.67
- Myy (Min.)
X
Z
Value
(kN·m/m)
8.86
X
Z
Value
(kN/m)
123.52
X
Z
Value
(kN/m)
77.83
- Mxx (Max.)
X
Z
Value
(kN·m/m)
15.16
- Mxx (Min.)
X
Z
Value
(kN·m/m)
67.15
- Myy (Max.)
X
Z
Value
(kN·m/m)
14.06
- Myy (Min.)
X
Z
Value
(kN·m/m)
7.32
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.06 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.05 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0013
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.26 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.03 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 77.126 4.802 10.010 25.344 5.522
ULC01
J 67.466 4.802 10.010 13.832 0.000
I 125.816 85.460 10.372 22.000 98.279
ULC02
J 117.536 85.460 10.372 10.072 0.000
I 125.660 14.764 15.028 39.366 -16.979
ULC03
J 117.380 14.764 15.028 22.084 0.000
I 103.328 7.976 11.890 30.070 9.172
ULC04
J 95.048 7.976 11.890 16.396 0.000
I 66.108 4.116 8.580 21.723 4.733
ULC05
J 57.828 4.116 8.580 11.856 0.000
I 5.116 6.996 7.444 18.881 -8.045
ULC06
J -3.164 6.996 7.444 10.320 0.000
I 103.328 7.976 11.890 30.070 9.172
ULC07
J 95.048 7.976 11.890 16.396 0.000
I -18.656 14.248 9.618 24.385 -16.385
ULC08
J -26.936 14.248 9.618 13.324 0.000
I 96.198 7.686 18.060 53.055 8.839
ULC09
J 87.918 7.686 18.060 32.286 0.000
I 77.178 3.356 10.960 27.740 3.859
ULC10
J 68.898 3.356 10.960 15.136 0.000
I 31.356 2.277 2.583 6.525 2.619
ULC11
J 25.146 2.277 2.583 3.555 0.000
I -90.628 19.947 0.311 0.841 -22.939
ULC12
J -96.838 19.947 0.311 0.483 0.000
I 24.226 1.987 8.753 29.511 2.285
ULC13
J 18.016 1.987 8.753 19.445 0.000
I 5.206 2.343 1.653 4.196 -2.694
ULC14
J -1.004 2.343 1.653 2.295 0.000
Pu max 125.816 85.460 18.060 22.000 98.279
Pu min -96.838 85.460 18.060 0.483 0.000
Applied Loads
Mux max 96.198 85.460 18.060 53.055 8.839
Muy max 125.816 85.460 18.060 22.000 98.279
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
209
400
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 2786557.35 N = 2786.56 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3817611.41 N = 3817.61 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2318228.38 N = 2318.23 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3668 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
10. TYPE - F5
3300
500
2300
700
150
4800
500
3300
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
92.60
- Mxx (Min.)
X
Z
Value
(kN·m/m)
38.77
- Myy (Max.)
X
Z
Value
(kN·m/m)
136.26
- Myy (Min.)
X
Z
Value
(kN·m/m)
82.24
X
Z
Value
(kN/m)
219.81
X
Z
Value
(kN/m)
491.18
491.18
158.18
158.18
Average
324.68
- Mxx (Max.)
X
Z
Value
(kN·m/m)
74.11
- Mxx (Min.)
X
Z
Value
(kN·m/m)
35.07
- Myy (Max.)
X
Z
Value
(kN·m/m)
108.23
- Myy (Min.)
X
Z
Value
(kN·m/m)
67.77
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0014
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.28 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0021
R = (H - χ) / (H - χ - d') = 1.251
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.28 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.13 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0013
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.26 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 500 X 700
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 174.094 7.658 0.224 6.309 37.907
ULC01
J 113.456 7.658 0.224 5.502 3.431
I 223.539 65.688 2.008 33.292 325.156
ULC02
J 171.564 65.688 2.008 23.352 5.188
I 231.771 37.776 3.704 22.079 186.991
ULC03
J 179.796 37.776 3.704 6.516 5.437
I 198.243 11.184 0.602 7.184 55.361
ULC04
J 146.268 11.184 0.602 7.896 4.423
I 148.175 6.396 0.424 5.370 31.660
ULC05
J 96.200 6.396 0.424 3.604 2.909
I 79.871 11.428 0.080 6.016 56.569
ULC06
J 27.896 11.428 0.080 5.620 0.844
I 196.147 10.848 1.066 7.108 53.698
ULC07
J 144.172 10.848 1.066 5.672 4.360
I 59.539 24.800 0.058 9.417 122.760
ULC08
J 7.564 24.800 0.058 9.704 0.229
I 196.993 10.864 5.028 58.405 53.777
ULC09
J 145.018 10.864 5.028 33.516 4.385
I 165.093 3.284 0.412 6.167 16.256
ULC10
J 113.118 3.284 0.412 8.206 3.421
I 81.255 3.156 0.770 4.326 15.622
ULC11
J 42.274 3.156 0.770 1.532 1.278
I -55.353 32.492 0.238 4.696 -160.835
ULC12
J -94.334 32.492 0.238 3.518 0.000
I 82.101 3.172 5.324 53.684 15.701
ULC13
J 43.120 3.172 5.324 27.330 1.304
I 50.201 4.408 0.116 1.819 21.820
ULC14
J 11.220 4.408 0.116 2.020 0.339
Pu max 231.771 65.688 5.324 22.079 186.991
Pu min -94.334 65.688 5.324 3.518 0.000
Applied Loads
Mux max 196.993 65.688 5.324 58.405 53.777
Muy max 223.539 65.688 5.324 33.292 325.156
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.50 m = 500.00 mm PL = 0.70 m = 700.00 mm
209
500
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3216575.13 N = 3216.58 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3944780.34 N = 3944.78 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2571034.10 N = 2571.03 kN
βC = 1.40 : Ratio of long side to short side of concentrated load or reaction area
bO = 4068 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
11. TYPE - F6
2300
700
2300
500
150
4800
500
2300
Unit : kN·m
Node Load Case FX FY FZ MX MY
Con'c self weight 0.00 0.00 109.44 0.00 0.00
Dead Soil Weight 0.00 0.00 426.82 0.00 0.00
Rack Dead 11.32 7.01 84.65 0.00 19.42
Surcharge 0.00 0.00 24.70 0.00 0.00
Live LL 9.52 5.56 45.19 0.00 17.00
CB3-02, Sub Total 9.52 5.56 69.89 0.00 17.00
CB3-C X -1.49 0.11 0.35 0.00 -2.97
Wind
Y -0.71 22.97 98.94 0.00 0.18
X 21.66 1.00 12.50 0.00 44.32
Seismic
Y -0.57 8.38 36.25 0.00 -0.63
+ 9.41 43.96 5.68 0.00 19.53
Temp
- -9.41 -43.96 -5.68 0.00 -19.53
Pp = 1/2 x kp x rs x h 2 x b
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
96.07
- Mxx (Min.)
X
Z
Value
(kN·m/m)
65.28
- Myy (Max.)
X
Z
Value
(kN·m/m)
109.49
- Myy (Min.)
X
Z
Value
(kN·m/m)
77.25
X
Z
Value
(kN/m)
381.65
223.18
Average
302.42
X
Z
Value
(kN/m)
383.57
218.14
Average
300.86
- Mxx (Max.)
X
Z
Value
(kN·m/m)
74.24
- Mxx (Min.)
X
Z
Value
(kN·m/m)
50.78
- Myy (Max.)
X
Z
Value
(kN·m/m)
86.22
48.44
Average
67.33
- Myy (Min.)
X
Z
Value
(kN·m/m)
61.65
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0015
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.28 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0017
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.26 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0010
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.19 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0012
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.24 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 500 X 700
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 179.148 9.814 15.848 105.636 48.579
ULC01
J 118.510 9.814 15.848 27.188 3.584
I 232.675 70.060 40.108 272.475 346.797
ULC02
J 180.700 70.060 40.108 73.940 5.464
I 219.043 35.444 17.524 113.812 175.448
ULC03
J 167.068 35.444 17.524 27.068 5.052
I 198.745 13.972 23.104 154.669 69.161
ULC04
J 146.770 13.972 23.104 40.304 4.438
I 153.835 8.500 12.392 82.268 42.075
ULC05
J 101.860 8.500 12.392 20.928 3.080
I 232.707 26.788 13.016 87.877 132.601
ULC06
J 180.732 26.788 13.016 23.448 5.465
I 199.305 14.148 20.720 138.116 70.033
ULC07
J 147.330 14.148 20.720 35.552 4.455
I 357.049 50.724 21.968 149.334 251.084
ULC08
J 305.074 50.724 21.968 40.592 9.225
I 211.245 14.972 44.764 306.206 74.111
ULC09
J 159.270 14.972 44.764 84.624 4.816
I 234.995 22.352 22.534 151.217 110.642
ULC10
J 183.020 22.352 22.534 39.674 5.535
I 83.983 4.469 4.303 28.194 22.122
ULC11
J 45.002 4.469 4.303 6.894 1.361
I 241.727 41.045 5.551 39.411 203.173
ULC12
J 202.746 41.045 5.551 11.934 6.131
I 95.923 5.293 28.347 196.284 26.200
ULC13
J 56.942 5.293 28.347 55.966 1.722
I 119.673 12.673 6.117 41.295 62.731
ULC14
J 80.692 12.673 6.117 11.016 2.440
Pu max 357.049 70.060 44.764 149.334 251.084
Pu min 45.002 70.060 44.764 6.894 1.361
Applied Loads
Mux max 211.245 70.060 44.764 306.206 74.111
Muy max 232.675 70.060 44.764 272.475 346.797
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.50 m = 500.00 mm PL = 0.70 m = 700.00 mm
209
500
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3216575.13 N = 3216.58 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3944780.34 N = 3944.78 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2571034.10 N = 2571.03 kN
βC = 1.40 : Ratio of long side to short side of concentrated load or reaction area
bO = 4068 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
12. TYPE - F7
3800
1150
3800
1500
600
1150
400
150
4800
500
3800
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
59.93
- Mxx (Min.)
X
Z
Value
(kN·m/m)
76.26
- Myy (Max.)
X
Z
Value
(kN·m/m)
70.32
- Myy (Min.)
X
Z
Value
(kN·m/m)
40.54
X
Z
Value
(kN/m)
240.53
X
Z
Value
(kN/m)
216.94
- Mxx (Max.)
X
Z
Value
(kN·m/m)
46.71
- Mxx (Min.)
X
Z
Value
(kN·m/m)
60.66
- Myy (Max.)
X
Z
Value
(kN·m/m)
55.52
- Myy (Min.)
X
Z
Value
(kN·m/m)
32.83
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0009
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.18 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0011
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.21 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0012
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.23 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.13 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 90.370 0.000 6.048 29.938 3.004
ULC01
J 48.790 0.000 6.048 1.329 1.622
I 136.512 0.708 43.540 215.523 7.001
ULC02
J 100.872 0.708 43.540 2.748 3.496
I 136.488 0.708 21.140 104.643 6.945
ULC03
J 100.848 0.708 21.140 2.747 3.440
I 114.360 0.000 8.944 44.273 3.801
ULC04
J 78.720 0.000 8.944 2.144 2.617
I 74.748 0.000 7.304 36.155 2.485
ULC05
J 39.108 0.000 7.304 1.065 1.300
I 77.460 0.000 5.184 25.661 2.575
ULC06
J 41.820 0.000 5.184 1.139 1.390
I 108.936 0.000 13.184 65.261 3.621
ULC07
J 73.296 0.000 13.184 1.997 2.436
I 114.360 0.000 8.944 44.273 3.801
ULC08
J 78.720 0.000 8.944 2.144 2.617
I 127.490 0.000 13.374 66.201 4.238
ULC09
J 91.850 0.000 13.374 2.502 3.053
I 112.320 5.450 8.804 43.580 52.656
ULC10
J 76.680 5.450 8.804 2.089 25.678
I 45.147 0.000 6.886 34.086 1.501
ULC11
J 18.417 0.000 6.886 0.502 0.612
I 50.571 0.000 2.646 13.098 1.681
ULC12
J 23.841 0.000 2.646 0.649 0.793
I 63.701 0.000 7.076 35.026 2.117
ULC13
J 36.971 0.000 7.076 1.007 1.229
I 48.531 5.450 2.506 12.405 52.669
ULC14
J 21.801 5.450 2.506 0.594 25.691
Pu max 136.512 5.450 43.540 215.523 7.001
Pu min 18.417 5.450 43.540 0.502 0.612
Applied Loads
Mux max 136.512 5.450 43.540 215.523 7.001
Muy max 48.531 5.450 43.540 12.405 52.669
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
209
400
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 1076486.31 N = 1076.49 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 1776232.09 N = 1776.23 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 895564.24 N = 895.56 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 1417 : Perimeter of critical (mm)
αS = 40 : Interior columns
= 30 : Edge columns
= 20 : Corner columns Applied
2100
800
2100
550
150
1000
500
2100
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
23.96
- Mxx (Min.)
X
Z
Value
(kN·m/m)
7.32
- Myy (Max.)
X
Z
Value
(kN·m/m)
22.40
- Myy (Min.)
X
Z
Value
(kN·m/m)
3.97
X
Z
Value
(kN/m)
111.29
X
Z
Value
(kN/m)
102.42
- Mxx (Max.)
X
Z
Value
(kN·m/m)
17.55
- Mxx (Min.)
X
Z
Value
(kN·m/m)
4.21
- Myy (Max.)
X
Z
Value
(kN·m/m)
18.11
- Myy (Min.)
X
Z
Value
(kN·m/m)
6.99
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0004
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.07 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.07 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.02 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.03 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 550 X 800
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 104.216 0.448 4.424 5.088 2.811
ULC01
J 86.506 0.448 4.424 0.000 2.296
I 146.016 3.172 35.480 40.802 19.820
ULC02
J 130.836 3.172 35.480 0.000 16.172
I 158.016 1.700 22.456 -25.824 -10.575
ULC03
J 142.836 1.700 22.456 0.000 -8.620
I 128.508 0.604 5.492 6.316 3.793
ULC04
J 113.328 0.604 5.492 0.000 3.098
I 73.256 0.688 9.728 11.187 4.311
ULC05
J 58.076 0.688 9.728 0.000 3.520
I 95.008 11.160 3.504 4.030 -69.730
ULC06
J 79.828 11.160 3.504 0.000 -56.896
I 96.364 1.212 17.364 19.969 7.596
ULC07
J 81.184 1.212 17.364 0.000 6.202
I 139.868 22.484 4.916 5.653 -140.487
ULC08
J 124.688 22.484 4.916 0.000 -114.630
I 113.278 0.966 11.112 12.779 -6.003
ULC09
J 98.098 0.966 11.112 0.000 -4.892
I 128.658 12.046 5.312 6.109 -74.125
ULC10
J 113.478 12.046 5.312 0.000 -60.272
I 8.050 0.797 13.555 15.588 4.984
ULC11
J -3.335 0.797 13.555 0.000 4.067
I 51.554 22.899 1.107 1.273 -143.099
ULC12
J 40.169 22.899 1.107 0.000 -116.765
I 24.964 1.381 7.303 8.398 -8.615
ULC13
J 13.579 1.381 7.303 0.000 -7.027
I 40.344 12.461 1.503 1.728 -76.737
ULC14
J 28.959 12.461 1.503 0.000 -62.407
Pu max 158.016 22.899 35.480 -25.824 -10.575
Pu min -3.335 22.899 35.480 0.000 4.067
Applied Loads
Mux max 146.016 22.899 35.480 40.802 19.820
Muy max 51.554 22.899 35.480 1.273 -143.099
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.55 m = 550.00 mm PL = 0.80 m = 800.00 mm
209
550
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3377599.23 N = 3377.60 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 2714420.90 N = 2714.42 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2760638.38 N = 2760.64 kN
βC = 1.45 : Ratio of long side to short side of concentrated load or reaction area
bO = 4368 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
3000
800
3000
550
150
1000
500
3000
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
54.34
- Mxx (Min.)
X
Z
Value
(kN·m/m)
55.68
- Myy (Max.)
X
Z
Value
(kN·m/m)
60.00
- Myy (Min.)
X
Z
Value
(kN·m/m)
50.19
X
Z
Value
(kN/m)
250.85
X
Z
Value
(kN/m)
277.69
- Mxx (Max.)
X
Z
Value
(kN·m/m)
39.19
- Mxx (Min.)
X
Z
Value
(kN·m/m)
41.06
- Myy (Max.)
X
Z
Value
(kN·m/m)
43.33
- Myy (Min.)
X
Z
Value
(kN·m/m)
36.51
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0008
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.15 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0009
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.17 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0009
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.16 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0008
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.14 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 550 X 800
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 164.150 2.142 5.866 -6.746 13.383
ULC01
J 146.440 2.142 5.866 0.000 10.920
I 247.740 9.256 30.684 -35.287 57.768
ULC02
J 232.560 9.256 30.684 0.000 47.124
I 279.420 8.368 22.164 25.489 52.259
ULC03
J 264.240 8.368 22.164 0.000 42.636
I 217.500 6.196 4.548 -5.230 38.685
ULC04
J 202.320 6.196 4.548 0.000 31.560
I 88.852 3.028 14.284 16.427 18.914
ULC05
J 73.672 3.028 14.284 0.000 15.432
I 121.460 16.820 8.484 -9.757 -105.095
ULC06
J 106.280 16.820 8.484 0.000 -85.752
I 113.804 8.580 34.076 39.187 53.571
ULC07
J 98.624 8.580 34.076 0.000 43.704
I 179.020 31.116 11.460 -13.179 -194.447
ULC08
J 163.840 31.116 11.460 0.000 -158.664
I 140.900 6.986 22.812 26.234 43.604
ULC09
J 125.720 6.986 22.812 0.000 35.570
I 177.680 14.744 10.068 -11.578 -91.046
ULC10
J 162.500 14.744 10.068 0.000 -74.090
I -38.968 3.761 36.644 42.141 23.489
ULC11
J -50.353 3.761 36.644 0.000 19.164
I 26.248 35.935 8.892 -10.226 -224.529
ULC12
J 14.863 35.935 8.892 0.000 -183.204
I -11.872 2.167 25.380 29.187 13.522
ULC13
J -23.257 2.167 25.380 0.000 11.030
I 24.908 19.563 7.500 -8.625 -121.127
ULC14
J 13.523 19.563 7.500 0.000 -98.630
Pu max 279.420 35.935 36.644 25.489 52.259
Pu min -50.353 35.935 36.644 0.000 19.164
Applied Loads
Mux max -38.968 35.935 36.644 42.141 23.489
Muy max 26.248 35.935 36.644 -10.226 -224.529
- Description
I : Pedestal Lower
J : Pedestal Top
2) Design Forces
h1 = 50.00 cm = 500.00 mm
PB = 0.55 m = 550.00 mm PL = 0.80 m = 800.00 mm
209
550
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3377599.23 N = 3377.60 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 4040157.04 N = 4040.16 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2760638.38 N = 2760.64 kN
βC = 1.45 : Ratio of long side to short side of concentrated load or reaction area
bO = 4368 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
3000
1250
4500
2000
550
1250
800
150
4800
500
3000
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
87.84
- Mxx (Min.)
X
Z
Value
(kN·m/m)
44.58
- Myy (Max.)
X
Z
Value
(kN·m/m)
98.11
- Myy (Min.)
X
Z
Value
(kN·m/m)
73.64
X
Z
Value
(kN/m)
351.10
236.11
Average
293.61
X
Z
Value
(kN/m)
309.31
- Mxx (Max.)
X
Z
Value
(kN·m/m)
55.91
- Mxx (Min.)
X
Z
Value
(kN·m/m)
26.08
- Myy (Max.)
X
Z
Value
(kN·m/m)
60.32
- Myy (Min.)
X
Z
Value
(kN·m/m)
60.82
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0013
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.21 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0015
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.23 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.10 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0011
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.23 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 550 X 800
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 139.454 4.004 2.758 38.530 19.820
ULC01
J 63.224 4.004 2.758 24.878 2.007
I 185.520 35.200 9.316 121.214 174.240
ULC02
J 120.180 35.200 9.316 75.100 3.815
I 185.640 21.776 2.068 35.801 107.791
ULC03
J 120.300 21.776 2.068 25.564 3.818
I 160.812 5.482 4.444 61.452 27.136
ULC04
J 95.472 5.482 4.444 39.454 3.030
I 119.532 3.432 2.364 33.026 16.988
ULC05
J 54.192 3.432 2.364 21.324 1.720
I -35.188 15.784 3.372 39.639 -78.131
ULC06
J -100.528 15.784 3.372 22.948 0.000
I 160.812 5.482 4.444 61.452 27.136
ULC07
J 95.472 5.482 4.444 39.454 3.030
I -148.628 32.950 6.460 74.679 -163.103
ULC08
J -213.968 32.950 6.460 42.702 0.000
I 169.332 6.072 22.204 267.654 30.056
ULC09
J 103.992 6.072 22.204 157.744 3.301
I 102.212 1.788 4.864 64.241 8.851
ULC10
J 36.872 1.788 4.864 40.164 1.170
I 91.719 2.088 0.900 14.814 10.336
ULC11
J 42.714 2.088 0.900 10.359 1.356
I -217.721 36.344 2.916 28.041 -179.903
ULC12
J -266.726 36.344 2.916 13.607 0.000
I 100.239 2.678 18.660 221.016 13.256
ULC13
J 51.234 2.678 18.660 128.649 1.626
I 33.119 5.182 1.320 17.603 25.651
ULC14
J -15.886 5.182 1.320 11.069 0.000
Pu max 185.640 36.344 22.204 35.801 107.791
Pu min -266.726 36.344 22.204 13.607 0.000
Applied Loads
Mux max 169.332 36.344 22.204 267.654 30.056
Muy max -217.721 36.344 22.204 28.041 -179.903
- Description
I : Pedestal Lower
J : Pedestal Top
2) Design Forces
h1 = 50.00 cm = 500.00 mm
PB = 0.55 m = 550.00 mm PL = 0.80 m = 800.00 mm
209
550
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3377599.23 N = 3377.60 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 2714420.90 N = 2714.42 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2760638.38 N = 2760.64 kN
βC = 1.45 : Ratio of long side to short side of concentrated load or reaction area
bO = 4368 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
3000
800
2000
1000
150
5700
800
3000
1) Vertical Reaction
Qa = 1500 kN
∴ Qu = 852.96 < Qa = 1500.00 O.K
2) Horizontal Reaction
Qa = 80 kN
∴ Qu = 55.71 < Qa = 80.00 O.K
3) Uplift Reaction
Qa = 300 kN
∴ Qu = N/A > Qa = 300.00 O.K
Vetical
Max
Horizontal
Max
Horizontal
Min
Vetical
Min
4) Reaction Summary
Fx max = 17.49 kN
(Refer to Reaction Summay table)
Fx max = 111.29 kN
(Refer to Reaction Summay table)
X Dir. Y Dir.
Pile No. Distance α Factor Pile No. Distance α Factor
2736 1500 1.88 0.08 2736 g Guide 1.00
2739 g Guide 1.00 2739 g Guide 1.00
SUM. 1.08 SUM. 2.00
- X Direction
Qu = 17.49 kN
- Y Direction
Qu = 111.29 kN
Unit : mm
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 5978886.59 N
= 5978.89 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 8388380.09 N
= 8388.38 kN
ΦVc = 0.75 x 0.33 x fck x b0 x d
= 3868691.32 N
= 3868.69 kN
βC = 1.00 : Ratio of long side to short side of concentrated load or reaction area
bO = 3927 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
Vertical
Max
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
126.05
- Mxx (Min.)
X
Z
Value
(kN·m/m)
224.31
- Myy (Max.)
X
Z
Value
(kN·m/m)
43.41
- Myy (Min.)
X
Z
Value
(kN·m/m)
258.54
X
Z
Value
(kN/m)
403.33
X
Z
Value
(kN/m)
854.55
51.85
AVERAGE
453.20
- Mxx (Max.)
X
Z
Value
(kN·m/m)
92.98
- Mxx (Min.)
X
Z
Value
(kN·m/m)
174.47
- Myy (Max.)
X
Z
Value
(kN·m/m)
32.38
- Myy (Min.)
X
Z
Value
(kN·m/m)
198.31
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0008
R = (H - χ) / (H - χ - d') = 1.200
A = 2 x 150 x 1000.00 / 7 = 42857 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.24 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.157
A = 2 x 150 x 1000.00 / 7 = 42857 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.12 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0012
R = (H - χ) / (H - χ - d') = 1.188
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.25 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0013
R = (H - χ) / (H - χ - d') = 1.188
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.28 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 800 X 1000
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 677.124 52.178 0.238 3.128 305.241
ULC01
J 513.324 52.178 0.238 1.736 20.143
I 1036.000 114.292 4.020 52.081 668.608
ULC02
J 895.600 114.292 4.020 28.564 35.143
I 1057.072 67.924 2.556 -33.117 397.355
ULC03
J 916.672 67.924 2.556 -18.164 35.970
I 871.732 73.714 0.534 6.932 431.227
ULC04
J 731.332 73.714 0.534 3.808 28.698
I 580.032 44.636 0.348 -4.476 261.121
ULC05
J 439.632 44.636 0.348 -2.440 17.251
I 238.296 133.052 0.580 7.545 778.354
ULC06
J 97.896 133.052 0.580 4.152 3.841
I 871.012 73.538 0.570 -7.383 430.197
ULC07
J 730.612 73.538 0.570 -4.048 28.669
I 187.540 250.370 1.286 16.659 1464.665
ULC08
J 47.140 250.370 1.286 9.136 1.850
I 843.312 65.134 8.606 -109.097 381.034
ULC09
J 702.912 65.134 8.606 -58.752 27.582
I 603.672 145.654 0.724 9.353 852.076
ULC10
J 463.272 145.654 0.724 5.118 18.179
I 279.000 17.662 0.996 -12.891 103.323
ULC11
J 173.700 17.662 0.996 -7.064 6.816
I -404.472 194.494 0.860 11.151 1137.790
ULC12
J -509.772 194.494 0.860 6.120 0.000
I 251.300 9.258 9.032 -114.605 54.159
ULC13
J 146.000 9.258 9.032 -61.768 5.729
I 11.660 89.778 0.298 3.845 525.201
ULC14
J -93.640 89.778 0.298 2.102 0.000
Pu max 1057.072 250.370 9.032 -33.117 397.355
Pu min -509.772 250.370 9.032 6.120 0.000
Applied Loads
Mux max 251.300 250.370 9.032 -114.605 54.159
Muy max 187.540 250.370 9.032 16.659 1464.665
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 80.00 cm = 800.00 mm
PB = 0.80 m = 800.00 mm PL = 1.00 m = 1000.00 mm
320
800
320
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 8003129.65 N = 8003.13 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 9251311.24 N = 9251.31 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 5975187.30 N = 5975.19 kN
βC = 1.25 : Ratio of long side to short side of concentrated load or reaction area
bO = 6160 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
1. 800 X 800
1) Rebar Design
3000
2000
800
1000
150
5700
800
3000
1) Vertical Reaction
Qa = 1500 kN
∴ Qu = 952.65 < Qa = 1500.00 O.K
2) Horizontal Reaction
Qa = 80 kN
∴ Qu = 33.61 < Qa = 80.00 O.K
3) Uplift Reaction
Qa = 300 kN
∴ Qu = N/A > Qa = 300.00 O.K
Horizontal
Min
Vetical
Min
4) Reaction Summary
Fx max = 31.59 kN
(Refer to Reaction Summay table)
Fx max = 66.27 kN
(Refer to Reaction Summay table)
- X Direction
Qu = 31.59 kN
- Y Direction
Qu = 66.27 kN
Unit : mm
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 6935508.45 N
= 6935.51 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 8699751.12 N
= 8699.75 kN
ΦVc = 0.75 x 0.33 x fck x b0 x d
= 4487681.94 N
= 4487.68 kN
βC = 1.00 : Ratio of long side to short side of concentrated load or reaction area
bO = 4555 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
Vertical
Max
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
109.65
- Mxx (Min.)
X
Z
Value
(kN·m/m)
11.35
- Myy (Max.)
X
Z
Value
(kN·m/m)
106.90
- Myy (Min.)
X
Z
Value
(kN·m/m)
19.28
X
Z
Value
(kN/m)
61.41
X
Z
Value
(kN/m)
60.72
- Mxx (Max.)
X
Z
Value
(kN·m/m)
79.91
63.52
AVERAGE
71.72
- Mxx (Min.)
X
Z
Value
(kN·m/m)
8.44
- Myy (Max.)
X
Z
Value
(kN·m/m)
77.04
- Myy (Min.)
X
Z
Value
(kN·m/m)
14.34
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
R = (H - χ) / (H - χ - d') = 1.157
A = 2 x 150 x 1000.00 / 7 = 42857 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.27 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
R = (H - χ) / (H - χ - d') = 1.157
A = 2 x 150 x 1000.00 / 7 = 42857 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.29 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0000
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.02 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.03 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 800 X 1000
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 279.160 7.616 0.392 5.079 44.554
ULC01
J 115.360 7.616 0.392 2.786 4.527
I 452.528 36.828 2.404 34.759 215.444
ULC02
J 312.128 36.828 2.404 20.696 12.248
I 452.528 4.164 1.700 -18.313 24.359
ULC03
J 312.128 4.164 1.700 -8.368 12.248
I 372.560 15.258 0.346 6.772 89.259
ULC04
J 232.160 15.258 0.346 4.748 9.110
I 239.280 6.528 0.336 4.354 38.189
ULC05
J 98.880 6.528 0.336 2.388 3.880
I 108.360 36.752 0.496 6.442 214.999
ULC06
J -32.040 36.752 0.496 3.540 0.000
I 372.560 15.258 0.346 6.772 89.259
ULC07
J 232.160 15.258 0.346 4.748 9.110
I 110.720 75.706 0.666 10.948 442.880
ULC08
J -29.680 75.706 0.666 7.052 0.000
I 369.130 14.988 20.814 -265.154 87.680
ULC09
J 228.730 14.988 20.814 -143.392 8.975
I 287.310 35.218 0.446 8.067 206.025
ULC10
J 146.910 35.218 0.446 5.458 5.765
I 105.300 0.000 0.000 0.000 4.132
ULC11
J 0.000 0.000 0.000 0.000 0.000
I -156.540 60.448 0.320 4.176 353.621
ULC12
J -261.840 60.448 0.320 2.304 0.000
I 101.870 0.270 21.160 -271.926 3.997
ULC13
J -3.430 0.270 21.160 -148.140 0.000
I 20.050 19.960 0.100 1.295 116.766
ULC14
J -85.250 19.960 0.100 0.710 0.000
Pu max 452.528 75.706 21.160 34.759 215.444
Pu min -261.840 75.706 21.160 2.304 0.000
Applied Loads
Mux max 101.870 75.706 21.160 -271.926 3.997
Muy max 110.720 75.706 21.160 10.948 442.880
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 80.00 cm = 800.00 mm
PB = 0.80 m = 800.00 mm PL = 1.00 m = 1000.00 mm
321
800
321
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 5322552.18 N = 5322.55 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 6712497.83 N = 6712.50 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 3973851.18 N = 3973.85 kN
βC = 1.25 : Ratio of long side to short side of concentrated load or reaction area
bO = 4084 : Perimeter of critical (mm)
αS = 40 : Interior columns
= 30 : Edge columns Applied
= 20 : Corner columns
1. 800 X 800
1) Rebar Design
1900
600
1700
400
150
1000
500
1900
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
25.73
- Mxx (Min.)
X
Z
Value
(kN·m/m)
10.89
- Myy (Max.)
X
Z
Value
(kN·m/m)
33.45
- Myy (Min.)
X
Z
Value
(kN·m/m)
9.04
X
Z
Value
(kN/m)
89.85
X
Z
Value
(kN/m)
134.90
- Mxx (Max.)
X
Z
Value
(kN·m/m)
17.21
- Mxx (Min.)
X
Z
Value
(kN·m/m)
6.51
- Myy (Max.)
X
Z
Value
(kN·m/m)
22.92
- Myy (Min.)
X
Z
Value
(kN·m/m)
3.27
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0004
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.07 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0005
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.09 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0002
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.02 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.01 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 141.302 16.604 4.214 2.602 19.095
ULC01
J 131.642 16.604 4.214 7.448 0.000
I 214.652 56.424 4.748 5.924 64.888
ULC02
J 206.372 56.424 4.748 11.384 0.000
I 214.652 5.112 5.612 0.562 -5.879
ULC03
J 206.372 5.112 5.612 7.016 0.000
I 179.576 21.372 4.592 2.863 24.578
ULC04
J 171.296 21.372 4.592 8.144 0.000
I 121.116 14.232 3.612 2.230 16.367
ULC05
J 112.836 14.232 3.612 6.384 0.000
I 87.892 0.904 2.068 12.614 1.040
ULC06
J 79.612 0.904 2.068 14.992 0.000
I 179.576 21.372 4.592 2.863 24.578
ULC07
J 171.296 21.372 4.592 8.144 0.000
I 113.128 5.284 1.504 23.630 -6.077
ULC08
J 104.848 5.284 1.504 25.360 0.000
I 184.566 23.442 7.468 77.182 26.958
ULC09
J 176.286 23.442 7.468 68.594 0.000
I 143.846 9.572 3.312 11.025 11.008
ULC10
J 135.566 9.572 3.312 14.834 0.000
I 43.452 4.851 0.828 0.524 5.579
ULC11
J 37.242 4.851 0.828 1.476 0.000
I -22.996 21.805 2.260 21.291 -25.076
ULC12
J -29.206 21.805 2.260 18.692 0.000
I 48.442 6.921 11.232 74.843 7.959
ULC13
J 42.232 6.921 11.232 61.926 0.000
I 7.722 6.949 0.452 8.686 -7.991
ULC14
J 1.512 6.949 0.452 8.166 0.000
Pu max 214.652 56.424 11.232 5.924 64.888
Pu min -29.206 56.424 11.232 18.692 0.000
Applied Loads
Mux max 184.566 56.424 11.232 77.182 26.958
Muy max 214.652 56.424 11.232 5.924 64.888
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
209
400
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 2786557.35 N = 2786.56 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 2491875.27 N = 2491.88 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2318228.38 N = 2318.23 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3668 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
1700
400
1700
600
150
1000
500
1700
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
15.87
- Mxx (Min.)
X
Z
Value
(kN·m/m)
5.89
- Myy (Max.)
X
Z
Value
(kN·m/m)
20.69
- Myy (Min.)
X
Z
Value
(kN·m/m)
6.82
X
Z
Value
(kN/m)
57.05
X
Z
Value
(kN/m)
63.41
- Mxx (Max.)
X
Z
Value
(kN·m/m)
10.03
- Mxx (Min.)
X
Z
Value
(kN·m/m)
4.22
- Myy (Max.)
X
Z
Value
(kN·m/m)
15.40
- Myy (Min.)
X
Z
Value
(kN·m/m)
3.91
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0002
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.04 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.06 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.02 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.01 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 75.726 9.436 1.890 -1.117 10.851
ULC01
J 66.066 9.436 1.890 -3.290 0.000
I 125.548 46.696 2.716 -3.449 53.700
ULC02
J 117.268 46.696 2.716 -6.572 0.000
I 125.548 14.936 3.244 -0.105 -17.176
ULC03
J 117.268 14.936 3.244 -3.836 0.000
I 102.808 12.958 2.470 -1.470 14.902
ULC04
J 94.528 12.958 2.470 -4.310 0.000
I 64.908 8.088 1.620 -0.957 9.301
ULC05
J 56.628 8.088 1.620 -2.820 0.000
I 39.436 2.120 0.076 -11.253 -2.438
ULC06
J 31.156 2.120 0.076 -11.340 0.000
I 102.808 12.958 2.470 -1.470 14.902
ULC07
J 94.528 12.958 2.470 -4.310 0.000
I 51.864 7.458 0.618 -22.061 -8.577
ULC08
J 43.584 7.458 0.618 -21.350 0.000
I 98.878 11.568 7.860 31.169 13.303
ULC09
J 90.598 11.568 7.860 22.130 0.000
I 85.478 7.188 1.760 -5.986 8.266
ULC10
J 77.198 7.188 1.760 -8.010 0.000
I 32.967 3.645 0.693 -0.409 4.192
ULC11
J 26.757 3.645 0.693 -1.206 0.000
I -17.977 16.771 2.395 -21.000 -19.287
ULC12
J -24.187 16.771 2.395 -18.246 0.000
I 29.037 2.255 6.083 32.229 2.593
ULC13
J 22.827 2.255 6.083 25.234 0.000
I 15.637 2.125 0.017 -4.926 -2.444
ULC14
J 9.427 2.125 0.017 -4.906 0.000
Pu max 125.548 46.696 7.860 -3.449 53.700
Pu min -24.187 46.696 7.860 -18.246 0.000
Applied Loads
Mux max 29.037 46.696 7.860 32.229 2.593
Muy max 125.548 46.696 7.860 -3.449 53.700
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
209
400
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 2786557.35 N = 2786.56 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3817611.41 N = 3817.61 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2318228.38 N = 2318.23 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3668 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
2000
850
2500
800
600
850
400
150
1000
500
2000
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
30.57
- Mxx (Min.)
X
Z
Value
(kN·m/m)
25.10
- Myy (Max.)
X
Z
Value
(kN·m/m)
40.56
- Myy (Min.)
X
Z
Value
(kN·m/m)
9.26
X
Z
Value
(kN/m)
116.71
X
Z
Value
(kN/m)
158.06
- Mxx (Max.)
X
Z
Value
(kN·m/m)
21.78
- Mxx (Min.)
X
Z
Value
(kN·m/m)
19.02
- Myy (Max.)
X
Z
Value
(kN·m/m)
29.54
- Myy (Min.)
X
Z
Value
(kN·m/m)
6.44
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0005
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.08 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.11 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0004
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.07 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0001
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.02 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 138.362 10.906 21.588 56.508 -12.542
ULC01
J 128.702 10.906 21.588 31.682 0.000
I 258.132 50.544 27.312 69.433 -58.126
ULC02
J 249.852 50.544 27.312 38.024 0.000
I 258.132 1.224 29.664 78.114 1.408
ULC03
J 249.852 1.224 29.664 44.000 0.000
I 205.806 18.918 24.744 64.272 -21.756
ULC04
J 197.526 18.918 24.744 35.816 0.000
I 118.596 9.348 18.504 48.436 -10.750
ULC05
J 110.316 9.348 18.504 27.156 0.000
I 160.876 22.364 20.240 52.824 -25.719
ULC06
J 152.596 22.364 20.240 29.548 0.000
I 205.806 18.918 24.744 64.272 -21.756
ULC07
J 197.526 18.918 24.744 35.816 0.000
I 290.366 44.950 28.216 73.048 -51.693
ULC08
J 282.086 44.950 28.216 40.600 0.000
I 184.426 16.698 39.374 118.966 -19.203
ULC09
J 176.146 16.698 39.374 73.686 0.000
I 238.826 29.558 26.484 68.713 -33.992
ULC10
J 230.546 29.558 26.484 38.256 0.000
I 45.837 3.789 4.068 10.411 -4.357
ULC11
J 39.627 3.789 4.068 5.733 0.000
I 130.397 29.821 7.540 19.188 -34.294
ULC12
J 124.187 29.821 7.540 10.517 0.000
I 24.457 1.569 18.698 65.106 -1.804
ULC13
J 18.247 1.569 18.698 43.603 0.000
I 78.857 14.429 5.808 14.852 -16.593
ULC14
J 72.647 14.429 5.808 8.173 0.000
Pu max 290.366 50.544 39.374 73.048 -51.693
Pu min 18.247 50.544 39.374 43.603 0.000
Applied Loads
Mux max 184.426 50.544 39.374 118.966 -19.203
Muy max 258.132 50.544 39.374 69.433 -58.126
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
209
400
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 2786557.35 N = 2786.56 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3817611.41 N = 3817.61 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2318228.38 N = 2318.23 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3668 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
3000
1250
4500
2000
600
1250
400
150
1000
800
3000
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
59.79
- Mxx (Min.)
X
Z
Value
(kN·m/m)
32.36
- Myy (Max.)
X
Z
Value
(kN·m/m)
66.38
- Myy (Min.)
X
Z
Value
(kN·m/m)
41.82
X
Z
Value
(kN/m)
166.39
X
Z
Value
(kN/m)
191.65
- Mxx (Max.)
X
Z
Value
(kN·m/m)
34.86
- Mxx (Min.)
X
Z
Value
(kN·m/m)
18.28
- Myy (Max.)
X
Z
Value
(kN·m/m)
38.43
- Myy (Min.)
X
Z
Value
(kN·m/m)
24.05
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.07 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0003
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.08 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0002
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.04 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0002
R = (H - χ) / (H - χ - d') = 1.148
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.05 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 141.134 10.724 2.870 17.315 12.333
ULC01
J 131.474 10.724 2.870 14.014 0.000
I 202.516 45.352 7.480 45.230 52.155
ULC02
J 194.236 45.352 7.480 36.628 0.000
I 202.564 10.232 4.288 25.863 -11.767
ULC03
J 194.284 10.232 4.288 20.932 0.000
I 171.952 14.422 4.600 27.782 16.585
ULC04
J 163.672 14.422 4.600 22.492 0.000
I 120.972 9.192 2.460 14.841 10.571
ULC05
J 112.692 9.192 2.460 12.012 0.000
I -64.004 19.744 2.732 16.506 -22.706
ULC06
J -72.284 19.744 2.732 13.364 0.000
I 171.952 14.422 4.600 27.782 16.585
ULC07
J 163.672 14.422 4.600 22.492 0.000
I -198.000 43.450 5.144 31.112 -49.968
ULC08
J -206.280 43.450 5.144 25.196 0.000
I 166.072 13.762 10.920 65.150 15.826
ULC09
J 157.792 13.762 10.920 52.592 0.000
I 99.992 3.372 4.630 27.977 3.878
ULC10
J 91.712 3.372 4.630 22.652 0.000
I 56.412 5.256 1.431 8.639 6.044
ULC11
J 50.202 5.256 1.431 6.993 0.000
I -313.540 52.616 1.975 11.968 -60.508
ULC12
J -319.750 52.616 1.975 9.697 0.000
I 50.532 4.596 7.751 46.007 5.285
ULC13
J 44.322 4.596 7.751 37.093 0.000
I -15.548 5.794 1.461 8.833 -6.663
ULC14
J -21.758 5.794 1.461 7.153 0.000
Pu max 202.564 52.616 10.920 25.863 -11.767
Pu min -319.750 52.616 10.920 9.697 0.000
Applied Loads
Mux max 166.072 52.616 10.920 65.150 15.826
Muy max -313.540 52.616 10.920 11.968 -60.508
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
359
400
359
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 6358758.47 N = 6358.76 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 10499927.20 N = 10499.93 kN
ΦVc = 0.75 x 0.33 x fck x b0 x d
= 5290059.57 N = 5290.06 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 4868 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
2600
800
2600
550
150
4800
500
2600
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
38.03
- Mxx (Min.)
X
Z
Value
(kN·m/m)
24.75
- Myy (Max.)
X
Z
Value
(kN·m/m)
40.66
- Myy (Min.)
X
Z
Value
(kN·m/m)
27.03
X
Z
Value
(kN/m)
124.58
X
Z
Value
(kN/m)
138.71
- Mxx (Max.)
X
Z
Value
(kN·m/m)
30.37
- Mxx (Min.)
X
Z
Value
(kN·m/m)
19.88
- Myy (Max.)
X
Z
Value
(kN·m/m)
25.15
- Myy (Min.)
X
Z
Value
(kN·m/m)
15.84
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.12 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.10 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0004
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.08 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0004
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.06 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 550 X 800
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 218.316 0.448 6.622 32.779 4.514
ULC01
J 142.086 0.448 6.622 4.510 2.296
I 301.688 1.180 32.700 161.865 11.889
ULC02
J 236.348 1.180 32.700 7.502 6.048
I 357.560 0.292 10.500 51.975 2.981
ULC03
J 292.220 0.292 10.500 9.275 1.536
I 276.188 0.604 9.066 44.877 6.098
ULC04
J 210.848 0.604 9.066 6.692 3.108
I 167.328 0.688 13.180 65.241 6.934
ULC05
J 101.988 0.688 13.180 3.237 3.528
I 212.720 11.208 3.452 17.087 -112.640
ULC06
J 147.380 11.208 3.452 4.678 -57.160
I 236.588 1.212 24.074 119.166 12.227
ULC07
J 171.248 1.212 24.074 5.435 6.228
I 327.372 22.580 4.618 22.859 -226.919
ULC08
J 262.032 22.580 4.618 8.317 -115.148
I 147.938 0.966 57.676 285.496 -9.704
ULC09
J 82.598 0.966 57.676 2.622 -4.922
I 291.898 12.096 6.606 32.700 -120.387
ULC10
J 226.558 12.096 6.606 7.191 -60.512
I 61.632 0.797 18.032 89.258 8.028
ULC11
J 12.627 0.797 18.032 0.401 4.083
I 152.416 22.995 1.424 7.049 -231.118
ULC12
J 103.411 22.995 1.424 3.282 -117.293
I -27.018 1.381 51.634 255.588 -13.903
ULC13
J -76.023 1.381 51.634 0.000 -7.067
I 116.942 12.511 0.564 3.712 -124.586
ULC14
J 67.937 12.511 0.564 2.156 -62.657
Pu max 357.560 22.995 57.676 51.975 2.981
Pu min -76.023 22.995 57.676 0.000 -7.067
Applied Loads
Mux max 147.938 22.995 57.676 285.496 -9.704
Muy max 152.416 22.995 57.676 7.049 -231.118
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.55 m = 550.00 mm PL = 0.80 m = 800.00 mm
209
550
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3377599.23 N = 3377.60 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 2714420.90 N = 2714.42 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2760638.38 N = 2760.64 kN
βC = 1.45 : Ratio of long side to short side of concentrated load or reaction area
bO = 4368 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
3000
800
3000
550
150
4800
500
3000
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
62.66
- Mxx (Min.)
X
Z
Value
(kN·m/m)
43.70
- Myy (Max.)
X
Z
Value
(kN·m/m)
55.14
- Myy (Min.)
X
Z
Value
(kN·m/m)
25.39
X
Z
Value
(kN/m)
157.55
X
Z
Value
(kN/m)
153.76
- Mxx (Max.)
X
Z
Value
(kN·m/m)
49.22
- Mxx (Min.)
X
Z
Value
(kN·m/m)
29.20
- Myy (Max.)
X
Z
Value
(kN·m/m)
32.66
- Myy (Min.)
X
Z
Value
(kN·m/m)
16.16
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0010
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.19 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0008
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.12 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.11 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0004
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.06 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 550 X 800
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 218.316 0.448 6.622 32.779 4.514
ULC01
J 142.086 0.448 6.622 4.510 2.296
I 301.688 1.180 32.700 161.865 11.889
ULC02
J 236.348 1.180 32.700 7.502 6.048
I 357.560 0.292 10.500 51.975 2.981
ULC03
J 292.220 0.292 10.500 9.275 1.536
I 276.188 0.604 9.066 44.877 6.098
ULC04
J 210.848 0.604 9.066 6.692 3.108
I 167.328 0.688 13.180 65.241 6.934
ULC05
J 101.988 0.688 13.180 3.237 3.528
I 212.720 11.208 3.452 17.087 -112.640
ULC06
J 147.380 11.208 3.452 4.678 -57.160
I 236.588 1.212 24.074 119.166 12.227
ULC07
J 171.248 1.212 24.074 5.435 6.228
I 327.372 22.580 4.618 22.859 -226.919
ULC08
J 262.032 22.580 4.618 8.317 -115.148
I 147.938 0.966 57.676 285.496 -9.704
ULC09
J 82.598 0.966 57.676 2.622 -4.922
I 291.898 12.096 6.606 32.700 -120.387
ULC10
J 226.558 12.096 6.606 7.191 -60.512
I 61.632 0.797 18.032 89.258 8.028
ULC11
J 12.627 0.797 18.032 0.401 4.083
I 152.416 22.995 1.424 7.049 -231.118
ULC12
J 103.411 22.995 1.424 3.282 -117.293
I -27.018 1.381 51.634 255.588 -13.903
ULC13
J -76.023 1.381 51.634 0.000 -7.067
I 116.942 12.511 0.564 3.712 -124.586
ULC14
J 67.937 12.511 0.564 2.156 -62.657
Pu max 357.560 22.995 57.676 51.975 2.981
Pu min -76.023 22.995 57.676 0.000 -7.067
Applied Loads
Mux max 147.938 22.995 57.676 285.496 -9.704
Muy max 152.416 22.995 57.676 7.049 -231.118
- Description
I : Pedestal Lower
J : Pedestal Top
2) Design Forces
h1 = 50.00 cm = 500.00 mm
PB = 0.55 m = 550.00 mm PL = 0.80 m = 800.00 mm
209
550
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3377599.23 N = 3377.60 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 4040157.04 N = 4040.16 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2760638.38 N = 2760.64 kN
βC = 1.45 : Ratio of long side to short side of concentrated load or reaction area
bO = 4368 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
2300
600
2300
400
150
4800
350
2300
Unit : kN·m
Node Load Case FX FY FZ MX MY
Con'c self weight 0.00 0.00 75.99 0.00 0.00
Dead Soil Weight 0.00 0.00 436.32 0.00 0.00
Rack Dead 15.42 7.79 91.93 0.00 22.63
Surcharge 0.00 0.00 25.25 0.00 0.00
Live LL 6.24 9.57 87.21 0.00 8.66
Sub Total 6.24 9.57 112.46 0.00 8.66
MD#1-2
X 0.00 0.00 0.00 0.00 0.00
Wind
Y 2.17 16.27 52.85 0.00 2.99
X 14.63 -2.22 -21.38 0.00 37.87
Seismic
Y 1.74 10.64 33.02 0.00 2.44
+ -0.98 21.57 0.00 0.00 -2.49
Temp
- 0.98 -21.57 0.00 0.00 2.49
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
66.18
- Mxx (Min.)
X
Z
Value
(kN·m/m)
32.54
- Myy (Max.)
X
Z
Value
(kN·m/m)
67.88
- Myy (Min.)
X
Z
Value
(kN·m/m)
35.13
X
Z
Value
(kN/m)
164.75
211.88
Average
188.32
X
Z
Value
(kN/m)
234.86
141.59
Average
188.23
- Mxx (Max.)
X
Z
Value
(kN·m/m)
50.19
26.57
Average
38.38
- Mxx (Min.)
X
Z
Value
(kN·m/m)
25.53
- Myy (Max.)
X
Z
Value
(kN·m/m)
52.12
34.02
Average
43.07
- Myy (Min.)
X
Z
Value
(kN·m/m)
28.12
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0025
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.24 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0026
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.27 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0012
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.16 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0013
R = (H - χ) / (H - χ - d') = 1.248
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.18 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 400 X 600
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 162.694 9.604 18.816 119.193 47.540
ULC01
J 121.114 9.604 18.816 26.054 4.026
I 278.988 49.428 24.888 156.316 244.669
ULC02
J 243.348 49.428 24.888 33.120 8.089
I 278.988 2.340 27.240 173.934 11.583
ULC03
J 243.348 2.340 27.240 39.096 8.089
I 226.662 17.802 22.338 141.515 88.120
ULC04
J 191.022 17.802 22.338 30.942 6.350
I 139.452 8.232 16.128 102.166 40.748
ULC05
J 103.812 8.232 16.128 22.332 3.451
I 110.996 3.528 16.008 101.412 17.464
ULC06
J 75.356 3.528 16.008 22.172 2.505
I 226.662 17.802 22.338 141.515 88.120
ULC07
J 191.022 17.802 22.338 30.942 6.350
I 169.750 5.718 22.098 140.007 28.304
ULC08
J 134.110 5.718 22.098 30.622 4.458
I 209.402 16.032 34.958 236.574 79.358
ULC09
J 173.762 16.032 34.958 63.532 5.776
I 198.882 8.632 21.018 133.161 42.728
ULC10
J 163.242 8.632 21.018 29.122 5.426
I 64.494 3.771 3.735 23.672 18.666
ULC11
J 37.764 3.771 3.735 5.184 1.255
I 7.582 19.749 3.495 22.164 97.758
ULC12
J -19.148 19.749 3.495 4.864 0.000
I 47.234 2.001 16.355 118.731 9.905
ULC13
J 20.504 2.001 16.355 37.774 0.682
I 36.714 5.399 2.415 15.318 26.725
ULC14
J 9.984 5.399 2.415 3.364 0.332
Pu max 278.988 49.428 34.958 156.316 244.669
Pu min -19.148 49.428 34.958 4.864 0.000
Applied Loads
Mux max 209.402 49.428 34.958 236.574 79.358
Muy max 278.988 49.428 34.958 156.316 244.669
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 35.00 cm = 350.00 mm
PB = 0.40 m = 400.00 mm PL = 0.60 m = 600.00 mm
134
400
134
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 1492344.95 N = 1492.34 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 1711547.47 N = 1711.55 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 1241530.67 N = 1241.53 kN
βC = 1.50 : Ratio of long side to short side of concentrated load or reaction area
bO = 3068 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
2200
900
4000
2200
500
900
700
150
4800
500
2200
In line with that, this section is focused on seeking where greater or lesser values than (±)ΦMn are using
the stress contour range in MIDAS Program, then adding supplementary rebar where required, checking that the stress
resultant output is not greater or lesser than revised design moment (±)ΦMn any more (where, the sign (+) means
tension stress in bottom and (-) in top of concrete foundation) and verifying no need of reinforcing bar.
The moment and shear force was determined on the basis of critical section.
Case of occurs stress is concentrated, it is unsuitable for use as a design value.
Thus, using the average value of the near stress
- Mxx (Max.)
X
Z
Value
(kN·m/m)
45.64
- Mxx (Min.)
X
Z
Value
(kN·m/m)
212.40
- Myy (Max.)
X
Z
Value
(kN·m/m)
48.13
- Myy (Min.)
X
Z
Value
(kN·m/m)
38.41
X
Z
Value
(kN/m)
268.78
X
Z
Value
(kN/m)
124.17
- Mxx (Max.)
X
Z
Value
(kN·m/m)
38.40
- Mxx (Min.)
X
Z
Value
(kN·m/m)
162.73
- Myy (Max.)
X
Z
Value
(kN·m/m)
37.98
- Myy (Min.)
X
Z
Value
(kN·m/m)
32.01
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.15 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0007
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.15 mm < Wa ( 0.30 ) mm ∴ O.K !
1) X Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0034
R = (H - χ) / (H - χ - d') = 1.320
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.29 mm < Wa ( 0.30 ) mm ∴ O.K !
2) Y Direction
0.85 x f'c 2 x Rn
ρ = 1 - 1 -
fy 0.85 x f'c
= 0.0006
R = (H - χ) / (H - χ - d') = 1.197
A = 2 x 75 x 1000.00 / 7 = 21429 mm2
W = 1.08 x R x fs x ³√(dc x A) x 0.00001
= 0.12 mm < Wa ( 0.30 ) mm ∴ O.K !
1. 500 X 700
1) Design Forces
Unit : kN·m
Combinations Part Pu Vux Vuy Mux Muy
I 100.104 4.564 4.214 26.655 22.592
ULC01
J 39.466 4.564 4.214 5.796 1.194
I 135.319 83.428 5.408 30.018 412.969
ULC02
J 83.344 83.428 5.408 3.248 2.520
I 135.163 16.808 10.076 65.136 83.200
ULC03
J 83.188 16.808 10.076 15.260 2.516
I 116.653 6.622 6.932 43.861 32.779
ULC04
J 64.678 6.622 6.932 9.548 1.956
I 85.803 3.912 3.612 22.847 19.364
ULC05
J 33.828 3.912 3.612 4.968 1.023
I 153.515 15.808 5.612 35.531 78.250
ULC06
J 101.540 15.808 5.612 7.752 3.071
I 116.653 6.622 6.932 43.861 32.779
ULC07
J 64.678 6.622 6.932 9.548 1.956
I 252.077 30.414 10.932 69.229 150.549
ULC08
J 200.102 30.414 10.932 15.116 6.051
I 123.403 7.512 1.962 6.480 37.184
ULC09
J 71.428 7.512 1.962 3.232 2.160
I 141.913 10.992 7.912 50.092 54.410
ULC10
J 89.938 10.992 7.912 10.928 2.720
I 64.352 2.124 2.709 17.136 10.514
ULC11
J 25.371 2.124 2.709 3.726 0.767
I 199.776 25.916 6.709 42.504 128.284
ULC12
J 160.795 25.916 6.709 9.294 4.862
I 71.102 3.014 2.261 20.246 14.919
ULC13
J 32.121 3.014 2.261 9.054 0.971
I 89.612 6.494 3.689 23.367 32.145
ULC14
J 50.631 6.494 3.689 5.106 1.531
Pu max 252.077 83.428 10.932 69.229 150.549
Pu min 25.371 83.428 10.932 3.726 0.767
Applied Loads
Mux max 252.077 83.428 10.932 69.229 150.549
Muy max 135.319 83.428 10.932 30.018 412.969
- Description
I : Pedestal Lower
J : Pedestal Top
2) Rebar Design
h1 = 50.00 cm = 500.00 mm
PB = 0.50 m = 500.00 mm PL = 0.70 m = 700.00 mm
209
500
209
2
ΦVc = 0.75 x 0.17 x + 1 x fck x b0 x d
βC
= 3216575.13 N = 3216.58 kN
αSd
ΦVc = 0.75 x 0.083 x + 2 x fck x b0 x d
b0
= 3944780.34 N = 3944.78 kN
ΦVc = 0.75 x 0.33 x fck x b 0 x d
= 2571034.10 N = 2571.03 kN
βC = 1.40 : Ratio of long side to short side of concentrated load or reaction area
bO = 4068 : Perimeter of critical (mm)
αS = 40 : Interior columns Applied
= 30 : Edge columns
= 20 : Corner columns
APPENDIX
- CABLE RACK#1 -
X
Position FX (kN) FY (kN) FZ (kN)
Load MX (kN·m) MY (kN·m) MZ (kN·m)
GRID Height(Z) Node EAST+ NORTH+ Vertical
3 DS 1.575581 5.318 52.749 0.000 -9.666 0.000
3 DC -0.05144 1.742 -1.207 0.000 -3.642 0.002
3 LL 2.982558 3.863 29.205 0.000 -18.363 0.000
3 TL(+) 2.658607 20.025 0.964 0.000 6.600 0.000
CB1-02 CB1-D EL+100200
3 TL(-) -2.6586 -20.025 -0.964 0.000 -6.600 0.000
3 WLY(Steel) -1.863504 22.873 178.437 0.000 6.346 0.005
3 ELX(Steel) -15.07298 -1.400 -7.568 0.000 -36.696 0.000
3 ELY(Steel) 0.278889 -6.959 -51.620 0.000 -1.056 -0.001
4 DS 1.81889 -5.319 55.013 0.000 -10.210 0.000
4 DC 2.466256 -2.043 33.612 0.000 -9.073 0.002
4 LL 3.138815 -3.837 29.082 0.000 -18.774 0.000
4 TL(+) 2.620617 -20.037 1.046 0.000 6.701 0.000
CB1-01 CB1-D EL+100200
4 TL(-) -2.62061 20.037 -1.046 0.000 -6.701 0.000
4 WLY(Steel) 1.602257 23.554 -178.857 0.000 -5.001 0.005
4 ELX(Steel) -14.942458 0.965 -3.193 0.000 -37.120 0.000
4 ELY(Steel) -0.196787 -7.000 51.732 0.000 0.643 -0.001
5 DS -0.411007 4.620 52.090 0.000 -2.836 0.000
5 DC -0.185429 1.542 -1.194 0.000 -1.280 0.000
5 LL -0.60218 4.495 51.016 0.000 -4.155 0.000
5 TL(+) 0.232159 19.729 -0.958 0.000 1.602 0.000
CB1-02 CB1-C EL+100200
5 TL(-) -0.232158 -19.729 0.958 0.000 -1.602 0.000
5 WLY(Steel) -0.043842 30.971 259.076 0.000 -0.297 -0.002
5 ELX(Steel) -3.960631 0.318 3.892 0.000 -25.355 0.000
5 ELY(Steel) 0.012294 -8.918 -74.402 0.000 0.083 0.001
6 DS -0.41191 -4.636 54.303 0.000 -2.842 0.000
6 DC -0.192258 -1.726 38.221 0.000 -1.326 0.000
6 LL -0.602999 -4.515 51.086 0.000 -4.161 0.000
6 TL(+) 0.231927 -19.716 -1.052 0.000 1.600 0.000
CB1-01 CB1-C EL+100200
6 TL(-) -0.231926 19.716 1.052 0.000 -1.600 0.000
6 WLY(Steel) 0.077044 31.239 -258.490 0.000 0.526 -0.002
6 ELX(Steel) -3.967919 -0.626 6.795 0.000 -25.405 0.000
6 ELY(Steel) -0.021886 -8.904 74.241 0.000 -0.149 0.001
Doc No : 00-UBT-C-51-001-001
Cable Rack Foundation Calculation Sheet Rev No : X2
- CABLE RACK#2 -
- CABLE RACK#3 -
- CABLE RACK#4 -
- MD#1-1 -
Y
4
2
3
X 1
- SP#1 -
Y 4
2
3
X 1
Y
4
2
3
X 1
- SP#4 -
Y 4
2
3
X 1
- MD#2 -
4
X 2
3
1
- MD#5 -
4
X 2 3
- COMMON RACK#6 -
-MD#7 -
4
2
X
3
1
- MD#8 -
Y 4
2
3
X 1
- MD#9 -
Y
4
2
3
X
1