Professional Documents
Culture Documents
REVIEWED
This document has been reviewed by LCI Consultants with the intent
of the contract subject to the following notes and satisfactory
operation, for compliance with the project design general intent only.
PROJECT: Walsh Bay Arts Precinct This review does not relieve the Sub-Contractor of responsibility for all
specified requirements, correctness of quantities, dimensions,
calculations, fabrication techniques, compliance with statutory
PROJECT NO. : 30M067 regulations & relevant codes and standards, nor for the verification of
the site conditions, accessibility and co-ordination with other trades.
Total Pages: 4
Revise and Resubmit:
19/07/19
Signed: .................................. Date: ....................
Type Of Notice
RFA INS RFI FIO
Request For Approval Instruction Request for Information For Information Only
Sent by
TO CC COMPANY ATTENTION
(email/fax/hand)
Richard Crookes (RCC) Ian Barrat Aconex
Richard Crookes (RCC) Steve Embleton Aconex
Richard Crookes (RCC) Peter Fulton Aconex
Richard Crookes (RCC) Michael Aquilina Aconex
Richard Crookes (RCC) Katerina Oustambasidis Aconex
Please find contained within this Project Notice our Sea Water Heat Exchangers for your review and approval.
We would request response on our selection by 12th of July, so as to progress procurement without impacting on
the programme.
Response/ Comments:
Confirm the sizing fits with the existing structure and provision has been made to adjust
the supports to suit
316 stainless steel frame is to be titanium for corrosion resistance.
PLATES
Model GLP-10T
Heat Rejection (Nominal) kw 35
Fluid Water Water
Density kg/m3 995 995
Specific Heat Capacity kJ/(kg*K) 4.186 4.186
Thermal Conductivity W/(m* K) 0.6 0.6
Water Flow Rate l/s 1.21
o
Inlet Temperature C 35
o
Outlet Temperature C 29.5
Pressure Drop kPa 45
Water volume Litres 26.5
Net Weight (Empty) kg 62.6
Length mm 4570
Width mm 9.5
Height mm 1200
HEAT EXCHANGER
Heat Rejection (Nominal) kW 315
No. of plates per Heat Exchanger 9
Water Flow Rate L/s 10.86 10.86
o
Inlet Temperature C 29.5 29.5
o
Outlet Temperature C 35 35
Pressure Drop kPa 45
Water volume Litres 278
Number of Passes x channel 1x9
Connection Diameter mm 110
Nozzle Orientation Vertical
Net Weight (Empty) kg 816
Overall Length mm 4835
Overall Width mm 2235
Overall Height mm 1660
CONSTRUCTION
Design Code ASME BPVC
Design Pressure MPa 0.4 0.4
Test Pressure MPa 1.0 1.0 316 stainless steel is not suitable
Design Temperature o
C 0 - 50 for this application. Provide
Plate Material Titanium titanium frame and support
Header material HDPE
Frame material 316 Stainless Steel
Support Hardware Material 316 Stainless Steel
Sealing Material Synthetic fiber sheet gasket
SJ / GLP Legs - (SHORT) - 3' (0.91 m) in Length, Provides 12" (304.80 mm) Clearance from Bottom. Use with 02T and 05TC Models
SJ / GLP Legs - (TALL) - 5' (1.52 m) in Length, Provides 12" (304.80 mm) Clearance from Bottom. Use with 03T, 04T, 05T, 08T and 10T Models
***Multiple plates of like capacity can be manifold in field with polyethylene pipe to accommodated larger loads. Or, we can custom build (pre-manifold multiple plates)
with headers equipped with flange connections (single point hookups), reinforced frame with legs on skids to stand off bottom (special quote required).
Example: 4 Ton (14.07 kW) Heat Pump would Require SJ/GPL-05T plate in Cooling Dominate Application
Each 12,000 Btu (3.52 kW) of Cooling Rejects Approximately 15,000 Btu (4.39 kW) Heat
Flow Rate: 3 gpm (0.189 l/s) per ton (3.52 kW) equipment.
Approx. (HR) Heat Transfer Rate**: 100 BTu/Ft2 (567.83 W /(m².°C) transfer surface of plate per degree DeltaT in still body of water.
Both sides of plate are exchanger surface. (Note, any current accentuates performance greatly and allows for closer grouping of multiple plate AWEB SUPPLY
assembly – such as river applications). **Shallow bodies of water AND colder climates will require additional plate capacity for heating. 7350 Tom Drive, Baton Rouge, LA 70806
225-928-2630 * 888-277-2932 - Fax 225-928-
Example: SJ-05T Plate SJ-05T Plate 2087
4' X 8' X 2 = 64 ft2 1.22 m x 2.44 m x 2 = 5.95 m2 email: info@awebgeo.com
64 X 100 = 6,400 5.95 m2 x 567.83 W/(m².°C) = 3,380.633 Website: www.awebgeo.com
6,400 X 10 ∆T/ᵒF = 64,000 BTU approx. HR 3,380.633 x 5.5556 ∆T/ᵒC = 18.7814 kW approx. HR Rev. 4/12
Is the pile size correct? Confirm allowance has been made to
provide for modification to suit exact pile sizes found on site.`
2592
ISOMETRIC
TOP VIEW
ELEVATION