Professional Documents
Culture Documents
● Main Display
LASER
HOLD CALC CHECK
Normal
The internal measurement value is
HI
displayed.
ALIGNMENT 1
2
3
R.V. ANALOG ZERO SHIFT
LASER
HOLD CALC CHECK
R.V.(Internal measurement value)
(2)
HI
(3)
R.V. ANALOG ZERO SHIFT
HI LO SHIFT TIMING
(13)
(4)
(5)
LASER
HI
HOLD CALC CHECK
Analog output (when it is set ON)
GO
LO BANK0
1
The voltage value (V) or the current (mA)
(6) (7) (8) (9) (10) (11) (12)
ALIGNMENT
2
value is displayed.
3
R.V. ANALOG ZERO SHIFT
HI LO SHIFT TIMING
here.
(10) Zero Shift input LED
not held.
3
1
Changing the bank (program)
Setup Functions
1. Press the up/down arrow button while pressing the [MODE] button.
Set the R.V. value to the Shift target value HOLD CALC CHECK
1. Press the left/right arrow buttons until the sub display shows the
LO BANK0
ALIGNMENT 1
2
3
[SHIFT]
ALIGNMENT 1
2
3
GO
LO
ALIGNMENT
BANK0
1
lightsR.V.HIup.
2
3
ZERO SHIFT
ANALOG
LO SHIFT TIMING BANK 1 lights R.V.
HI
ANALOG
LO SHIFT
ZERO SHIFT
TIMING
Press ▼ while
holding down the
Press ▼ while holding
[MODE] button.
2. Press the up/down arrow button to change the Shift target value. down the [MODE] button.
HOLD CALC CHECK
GO
HI
LO BANK0
ALIGNMENT 1
4. The current R.V. value would be set to the Shift target value.
2
3
01 Measurement direction
HOLD CALC CHECK
LASER
HI
GO
1. When the Key Lock is set, press the MODE and the up (or down) Set the measurement direction from [Normal] and [Reverse].
arrow button for at least 2 seconds. [Normal]: The value increases when the target comes close to the
2. The Key Lock would be cancelled. sensor head.
[Reverse]: The value decreases when the target comes close to the
Initializing the sensor sensor head.
1. Press the SET button 5 times while HOLD CALC CHECK
02 Sampling rate
LASER
pressing the MODE button. The main GO
HI
HOLD CALC CHECK
display will show “rESET”. LO
ALIGNMENT
BANK0
1
LASER
HI
2
3 GO
R.V. ANALOG ZERO SHIFT LO BANK0
HI LO SHIFT TIMING 1
Performing the initial reset 2
3
R.V. ANALOG ZERO SHIFT
“AnLG”.
HI
Analog
LO
SHIFT
output TIMING
Set the average rate. High-pass filter and Step count filter can be set
here.
4. Select the analog output from “oFF”, LASER
HOLD CALC CHECK
2
04 Alarm setting Advanced setting mode
HOLD CALC CHECK
LASER
HI How to enter the Advanced setting mode
GO
LO BANK0
1
2 1. Press the [MODE] button for at least 2 seconds.
3
R.V. ANALOG ZERO SHIFT
HI LO SHIFT TIMING 2. Press the [MODE] or left/right arrow HOLD CALC CHECK
0.33ms) times, the previous value is held until the next measurement is
successful. 3. Press the up/down arrow button. The HOLD CALC CHECK
LASER
[Clamp]: When the measurement fails (out of the measurement range), main display will show “Pro”. GO
HI
13 Memorizing the zero shift Set if the shift target value has to be
memorized to the EEPROM or not,
when the zero shift was input.
14 Interference prevention Set to use the interference
prevention function.
1114-1
3