Professional Documents
Culture Documents
Creat Fault Indicator
Creat Fault Indicator
Principle
Recognize the characters of short-circuit current:
the current increment I caused by short-circuit fault.
The line voltage and current drop to zero because of short-circuit.
Meeting all the above 2 conditions at the same time is the criterion of action indication.
Type Code
FI
3h
Reset Time 6h
12h
default (24h or 20min)
Indication & Signal Default: flag
Transmisstion Mode F: add flash
O: add fibre-optic transmission signal
W: add wireless transmission signal
Design Serial No.
1.2.3...(or default)
A: naked wire
B: busbar
Application Place
C: cable
D: overhead insulated wire
P: Panel
Drive Power 2: line current
3: add lithium battery
fault indicator
Note: Special application place (rail line, self-closing line, above 35kV line etc.) or special re-
quirements please indicate when ordering.
CHARACTERISTICS
CHARACTERISTICS
Features
Fault Identification fault identification function, no need to define actuate current ratings.
recognize the fault character. For permanent faults, reset after re-
Automatic Reset energized. For instantaneous faults, reset in defined time.
eliminate misact phenomenon of closing field-excitation inrush.
Inrush Restrain directly installed on line and work outside chronically.
Live Line Operation
Substation C.B. 1 2
3
4 5 6
Substation CB 1 2
15 years experience
More than 1,000,000 pieces work in field
FI Series Fault Indicator
Features
Fault Identification short-circuit fault identification, no need to
define actuate current rating;
FI-3DF
Ratings
Line Voltage (1~35)kV
Minimum Load Current 8A
Conductor Size Φ(8~41)mm
Short Time Withstand Current 31.5kA/2s
Reset Time After Re-energized 20min
Temperature Range -35 70
Operation Life 2000times
Weight 450g
PRODUCTINTRODUCTION
PRODUCTINTRODUCTION
FI-2B1 Busbar Type Fault Indicator
Apply to Equipment Which Uuse Busbar
Features
Fault Identification fault identification function, no need to define
the actuate current rating.
FI-2C1O/3PO, FI-2B1O/3PO
Panel Type Fault Indicator
General
3 detectors installed on phase and one FI-3PO fault indicator installed on pad-mounted switchgear panel
compose this product.
Busbar outline adopts FI-2B1O as sensor.
Cable outline adopts FI-2C1O as sensor.
FI-2C1O/3PO FI-2B1O/3PO
Features
Fault Identification have the function of short-circuit fault identification, no need to
define the actuate current rating.
Inrush Restrain eliminate misact phenomenon of closing field-excitation inrush.
Reset Mode by hand or automatic reset.
Indication Mode flash light.
Live Line Installing and Removing detectors can be installed or removed on live line.
Rustproof the structural parts use rustproof material.
Inverse Time Limit Operating maximum suits substation about the protecting operating
Characteristic characteristic, and improve the actuate accuracy rating.
Enclosed Electron Switch send fault signal to FTU by electron switch on/off to implement
the supervisory function
Optical Fiber Transfer Signal isolate primary and secondary connection, and to ensure equip-
ments and personnel safety.
Equipement Self-Checking Button can check inside battery situation of FI-3PO fault indicator
momentarily.
RATINGS
RATINGS
Ratings
Line Voltage (1~35)kV
Minimum Load Current 8A
Conductor Size Φ(8~41)mm
Busbar Size Wide(40~60)mm Thick(4~10)mm
Short Time Withstand Current 31.5kA/2s
Reset Time After Re-energized 20min
Temperature Range -35 ~ 70
Operation Life 2000times
Weight 450g
FI-2C1O
FI-2B1O
FI Series Fault Indicator
Features
Fault Identification FI-2C10 has the function of short-circuit fault identification, no need
to define the actuate current rating.
FI-CT-1 zero-phase sequence current-transformer actuate value and
respond time can be set continuously.
Inrush Restrain eliminate misact phenomenon of closing field-excitation inrush.
Reset Mode by hand or automatic reset.
Indication Mode flash light.
Live Line Installing and Removing FI-2C1O fault indicator can be installed or removed on live line.
Application