Professional Documents
Culture Documents
attery-powered, direct-reading instruments are the selection of protective equipment necessary How Combustible Gas Monitors W ork
lassified as two groups—single-gas instruments for the tasks in the area. It may also dictate the
r multiple-gas instruments—typically duration of worker exposure to the environment To understand how portable combustible gas
monitoring one or a combination of the following of the space, or whether an entry will be made detection instruments work, it is first important
tmospheric conditions: at all. Substance-specific detectors should be to understand what is meant by the Lower
. oxygen deficiency or enrichment; used whenever actual contaminants have been Explosive Limit (LEL) and Upper Explosive Limit
identified. (UEL).When certain proportions of combustible
. the presence of combustible gas; and
vapors are mixed with air and a source of ignition
. the presence of certain toxic gases.
is present, an explosion can occur.The range of
Depending on the capabilities of the instrument, concentrations over which this reaction can occur
monitoring can be conducted simultaneously is called the explosive range.This range includes
or oxygen and combustible gas, or for oxygen, all concentrations in which a flash will occur or a
ombustible gas and toxic gases.These devices flame will travel if the mixture is ignited (see
re commonly referred to as 2-in-1, 3-in-1, 4-in-1 Figure 3).The lowest percentage at which this
r 5-in-1 alarms. can happen is the LEL; the highest percentage is
No matter which type of instrument is used to the UEL.
heck environmental gas concentrations, regular Most combustible instruments display gas
monitoring should be performed because a Figure 2 concentrations as a percentage of the LEL. Some
ontaminant’s level of combustibility or toxicity models have gas readouts as a percentage by vol-
might increase even if it initially appears to be ume and others display both percent of LEL and
ow or non-existent. In addition, oxygen percent combustible gas by volume.What’s the
eficiency can occur unexpectedly. difference? For example, the LEL of methane (the
major component in natural gas) is 5 percent by
Atmospheric Composition volume, and the UEL is 15 percent by volume. If
we slowly fill a room with methane, when the
o determine the composition of an atmosphere, concentration reaches 2.5 percent by volume, it is
eliable instruments should be used to draw air 50 percent of the LEL; at 5 percent by volume it is
amples. If possible, do not open the entry portal Figure 3 100 percent of the LEL. Between 5 and 15 percent
o the confined space before this step has been by volume, a spark could set off an explosion.
ompleted. Sudden changes in atmospheric com- Combustible Gases
osition within the confined space could cause
iolent reactions, or dilute the contaminants in In order for combustion to occur, there must be
he confined space, giving a false low initial gas three elements:
oncentration. 1.fuel
When testing permit-required spaces for accept- 2. oxygen to support combustion
ble entry conditions, always test in the following 3. heat or a source of ignition
rder: This is known as the fire triangle, but if you
. oxygen content remove any one of the legs, combustion will not
. flammable gases and vapors occur (see Figure 2). Figure 4
. potential toxic air contaminants The percentage of combustible gas in the air is Different gases need different percent by volume
important, too. For example, a manhole filled concentrations to reach 100 percent of the LEL
with fresh air is gradually filled by a leak of (see Figure 4). Pentane, for example, has an LEL of
combustible gas such as methane or natural gas, 1.5 percent. Instruments that measure in percent
mixing with the fresh air. As the ratio of gas to air of the LEL are easy to use because, regardless of
changes, the sample passes through three the gas, you are most concerned with how close
ranges: lean, explosive and rich (see Figure 3). In the concentration is to the LEL.
the lean range, there isn’t enough gas in the air to
burn. On the other hand, the rich range has too
much gas and not enough air. However, the Single-Gas Monitors for Oxygen Deficiency
gure 1 explosive range has just the right combination of Oxygen indicators measure atmospheric concen-
Comprehensive testing should be conducted in gas and air to form an explosive mixture. Care trations of oxygen. Concentrations are generally
arious locations within the work area. Some must be taken, however, when a mixture is too measured over a range of 0 to 25 percent oxygen
ases are heavier than air, and tend to collect at rich, because dilution with fresh air could bring in air, with readings being displayed on either
he bottom of a confined space. Others are the mixture into the flammable or explosive digital readout or an analog meter.
ghter, and are usually in higher concentrations range. An analogy is the automobile that won’t
Oxygen indicators are calibrated with uncontami-
ear the top of the confined space. Still start on a cold morning (a lean atmosphere
nated fresh air containing a minimum of
thers are the same molecular weight as air, because the liquid gasoline has not vaporized
20.8 percent oxygen.With some models, an
o they can be found in varying concentrations sufficiently), but can be flooded with too much
alarm is activated when oxygen levels drop below
hroughout the space.This is why test samples gasoline (a rich atmosphere with too much
19.5 percent.
hould be drawn at the top, middle and bottom vaporization). Eventually,when the right mixture of
f the space to pinpoint varying concentrations of gas and air finally exists (explosive), the car starts.
ases or vapors (see Figure 1).The results of the
tmospheric testing will have a direct impact on
Single-Gas Monitors for Combustible Gases Multiple-Gas Monitors for Oxygen and Detector Tube Sampling Systems
Combustible Gas
Detector tube-type devices are recommended for
In applications where it is necessary to determine conducting quick evaluations of potential hazards
oxygen and combustible gas levels simultaneous- that cannot otherwise be measured.With detec-
ly, 2-in-1 diffusion-type devices can be used. tor tubes, a known volume of air is drawn
Sensors measure 0 to 100 percent of the LEL and through the tube, using a manually operated or
oxygen from 0 to 25 percent. Remote sampling battery-powered sampling pump. If gas or vapor
requires either a pump module or an aspirator is present in the air, chemically treated granules in
bulb adapter. the tube are stained a different color. By measur-
ing the length of the color stain within the tube,
Figure 5 users can determine concentration levels.
Multiple-Gas Monitors for Oxygen,
Single-gas instruments for monitoring Combustible and Toxic Gases Most tubes available today are made of glass,
combustible gases and vapors are generally have break-off tips, and are filled with treated
Toxic gases and vapors, which can be inhaled or chemical granules.They generally have a shelf life
calibrated on pentane and are designed for gen- absorbed through the skin, are frequently found
eral-purpose monitoring of hydrocarbon vapors. of 24 to 30 months.
in confined spaces. Sometimes, these atmospher-
Such instruments operate by the catalytic action One type of pump frequently used with a
ic hazards can also displace oxygen and may inca-
of a heated platinum filament in contact with detector tube is a compact, bellows-type device.
pacitate the body’s ability to maintain respiration.
combustible gases (see Figure 5).The filament Accurate and repeatable sample flows can be
Some toxic gases and vapors can also cause long-
is heated to operating temperature by an electric assured by a shaft that guides the bellows during
term physical damage to the body in cases of
current.When the gas sample contacts the heat- compression. Some models feature an end-of-
repeated exposure.
ed filament, combustion on its surface raises the stroke indicator that lets the user know when a
temperature in proportion to the quantity of A number of instruments are available to assist in full air sample has been drawn. Models with an
combustibles in the sample. A Wheatstone detecting toxic gas. Pocket-size monitors operate integral stroke counter eliminate the tedious
bridge circuit, incorporating the filament as one by diffusion or an aspirator bulb. Larger instru- recording of multiple pump strokes.
arm, measures the change in electrical resistance ments with built-in pumps draw samples from
due to the temperature increases.This change the immediate area or from outside the confined
space work area when used with sampling lines. Personal Sampling
indicates the percentage of combustible gas
present in the sample. Diffusion-type instruments are available for Personal sampling is used to determine the con-
simultaneously measuring the LEL of combustible centration of airborne contaminants. Personal
gases, oxygen levels and toxic levels (in parts per sampling pumps are designed to measure
Single-Gas Monitors for Toxic Gases
million) of H2S, CO and other toxic gases. Alarms individual workers’exposures, so they typically
Compact, battery-powered devices can be used to also alert the user to low and high oxygen levels. are lightweight, belt-mounted, battery-powered
measure levels of such gases as carbon monoxide Remote sampling pump adapters are available to devices.
(CO) or hydrogen sulfide (H2S), depending on the convert these diffusion-type instruments into The process of sampling entails drawing a prede-
model selected.Toxic gas monitors use electro- pump-style instruments. termined volume of air through a filter designed
chemical cells (see Figure 6). If the gas of interest to trap contaminants.The filter is contained in a
enters the cell, the reaction produces a current plastic cassette, which is attached by plastic
output proportional to the amount of gas tubing to a sampling pump calibrated to draw a
in the sample.With these instruments, audible specific, known volume of air into the filter.
and visible alarms sound if the gas concentration After air samples are drawn, the filters are sent
exceeds a preset level.These devices are well suit- to a laboratory where they are examined to
ed for use in confined spaces containing motors determine the level of exposure.
or engines, which can generate large quantities of
CO, as well as in sewers, waste treatment plants Personal sampling determines the concentration
and “sour crude”processing stations which tend found in the “breathing zone”or the area near the
to have hazardous volumes of H2S. Figure 7 worker’s face, which is usually measured at or
near the collar or lapel.
Photoionization Devicesfor Toxic Gases
and Vapors Calibration
A photoionization detector, featuring micro- To ensure the accuracy of all monitoring and
processor technology, uses ultraviolet light to detection equipment, calibration should be
ionize molecules of chemical substances in a performed regularly. If the instrument reading
gaseous or vaporous state (see Figure 7). differs significantly from the values of the known
A real-time digital readout allows the user to standard, the instrument should not be used until
make an immediate determination of gas it has been adjusted or, if necessary, repaired.
Figure 6 and vapor concentrations. Depending upon
calibration input, gas and vapors are measured
over a 0.1 to 10,000 ppm scale. Some instruments
automatically compensate for signal loss due to
humidity, which is inherent in all PID detectors.
FiveStar® Alarm
he FiveStar Alarm provides the flexibility to meet your gas
etection needs, yet is incredibly simple to use.The durable,
igh-impact case makes it long-lasting, while the advanced
rgonomic design and software reduce worker load and
implify operation.This means less time spent training and
ess time out of service. Over its life, the FiveStar Alarm’s ease
f use, safety features, and long-term money savings combine
o provide the best in gas detection available today.
The FiveStar Alarm s simplicity is obvious The FiveStar Alarm saves money:
rom the start
: • Unbeatable warranty and service.
Three well-marked, easy-to-use keys. • Long-life combustible sensor.
Display faces user. • One-button calibration saves training and gas.
Industry leading RFI protection. • 5-gas capability means one detector can do the job of two detectors.
Flexible smart sensors. • Battery “gas gauge”reduces down time.
Weatherproof—IP54-rated. • 20-hour NiMH battery option means one battery can do the job of two.
Gas sensors available—you can order the FiveStar Alarm with sensors to detect:
The FiveStar Alarm s advanced softwarefeatures • Combustible gas (0–100% LEL or 0–5% methane)
mean safer operation: • Oxygen (0–25%)
Limits on sensor zeroing. and up to three of the following gases:
Limits on one-button calibration. • Ammonia 0–100 ppm • Nitric oxide 0–100 ppm
User acknowledges configuration changes. • Carbon monoxide 0–2000 ppm • Nitrogen dioxide 0–100 ppm
Data recording is standard. • Chlorine 0–20 ppm • Phosphine 0–5 ppm
• Chlorine Dioxide 0–5 ppm • Sulfur dioxide 0–100 ppm
or more complete information, please refer to
• Hydrogen sulfide 0–500 ppm
Bulletin 0816-06-MC.
Moregas detection capabilities arecontinually int roduced. Callfor availability of other gas
detection capabilities. Some configuration limitations apply.
iveStar Alarms can be ordered in one of two convenient ways. Either select from the most popular kit combinations below or refer to MSA’s highly effective
ustom-ordering process,“Assemble-to-Order.”
ap mp
Pu ket ase on Ki
t
FiveStar Alarm Kit Options r y er C
tte r
ge ar
g
tion
ec
k
ne be Jac ng C ti
Ba Char h a ch Li o r
the rryi
a
t C alibr e r
tP r
10
Cd ls ft lib
LEL O2 CO H2
S Ni AC Fas C Pu 1f Lea Ca Ca
eluxe, 4-gas 10018002 • • • • • • • • • • • •
eluxe, 3-gas, CO 10018003 • • • • • • • • • • •
eluxe, 3-gas, H2S 10018004 • • • • • • • • • • •
dustrial, 4-gas 10018005 • • • • • • • • • •
dustrial, 3-gas, CO 10018006 • • • • • • • • •
dustrial, 3-gas, H2S 10018007 • • • • • • • • •
conomy, 4-gas 10018008 • • • • • • •
conomy, 3-gas, CO 10018009 • • • • • •
conomy, 3-gas, H2S 10018030 • • • • • •
A. Electrochemical Sensor Options Sensors (Select 4) Code H. Sampling Lines Sampling Lines Code
Please list the code number for the toxic None 0 MSA’s high-speed sampling lines are of the None 0
gas sensors desired in the spaces to the Oxygen (0-25%) 1 highest quality materials guaranteed to not 5-foot coiled 1
right. In order to properly process your Carbon Monoxide (0-2000 ppm) 2 alter sample concentration. Screw fittings 10-foot 2
order, list them in descending order. Use Hydrogen Sulfide (0-200 ppm) 3 with O-Ring couplings at each end ensure 15-foot 3
zeros to complete any of the four selections Nitric Oxide (0-100 ppm) 4 that there are no leaks when the system is 25-foot 4
where no sensor is desired (e.g. 2100). operating.
Nitrogen Dioxide (0-100 ppm) 5
Add the price of each sensor to obtain the
sensor sub-total pricing. Sulfur Dioxide (0-100 ppm) 6 I. Sampling Probes Sampling Probe Code
Chlorine (0-20 ppm) 7 MSA’s sampling probes are durable and None 0
Phosphine (0-5 ppm) 8 comfortable to use. The built-in WaterStop® 8" probe 1
Ammonia (0-100 ppm) 9 filter in the handle of the probe ensures your 1-foot straight 2
Chlorine Dioxide(0-5 ppm) A sampling system is not contaminated with 3-foot straight 3
dirt and debris if the probe tip is dipped 3-foot, holes near tip 4
B. Combustible Gas Sensor Options Sensors Code under water. You must order a probe if you
None 0 3-foot, holes near handle 5
If a combustible gas sensor is desired, order a sampling line as we strongly
select type of display. There are two options % CH 4 (Methane) M recommend you operate the instrument Hot-gas sampling probe 6
available: 0-5% Methane by vloume (%CH4) % LEL Pentane L with this filter in place.
or 0-100% Lower Explosive Limit (%LEL
Pentane)
J. Carrying Attachments Belt Clip Code
While a high strength, molded plastic belt Molded plastic belt clip 1
C. Page Options Page Options Code clip is offered with the instrument at no Swivel belt loop 2
Select your desired combination of the No option pages active 0 charge, there are three other options for Pistol grip handle 3
following pages: Datatagging only 3 handling the instrument. The swivel belt Stainless steel belt clip 4
Peak Peak, STEL &TWA A loop allows quick release from your belt
Short Term Exposure Limit (STEL) All four option pages active B with a half turn. The pistol grip kit is helpful
Time Weighted Average (TWA) for longer stints of hand held sampling.
Datatagging K. Instrument Jacket Instrument Jacket Code
D. Alternate Languages Language Code To offer the highest levels of environmental None 0
The FiveStar Alarm speaks your worker’s English only 0 and rough handling protection for your Leather Case 1
language. Select the alternative languages FiveStar Alarm, you can order either a leather Cordura Nylon Jacket 2
English, Spanish & French 1
option and the instrument will display a or Cordura Nylon jacket. The cases are
screen at battery attach which asks user to custom designed to fit either the diffusion
select between three languages for screen instrument or the instrument with the
displays. pump.
E. Battery Pack Options Battery Pack Code L. Calibration Kits Calibration Accessories Code
There are multiple, flexible options to None 0 MSA provides two options for verifying None 0
power the instrument. The standard NiCd Standard NiCd Rechargeable A instrument calibration. The RP kit, with a Model RP Calibration Kit 1
and heavy-duty NiMH rechargeable battery Replaceable “AA” B constant flow regulator and replaceable Squirt Gas Check Kit 2
packs have a built-in battery gauge to cylinders provides the greatest accuracy.
Codes A & B C
provide the remaining hours of run time The Squirt® Gas Check Kit’s aerosol canisters
NiMH D provides an economical means to verify
for the instrument. The NiMH battery Codes B & D E
provides up to 20 hours of continuous instrument calibration.(Only available in ATO
operation for long-running jobs. The for Combustible, O 2,CO,H 2S other gases must
convenient replaceable pack can operate be purchased separately.)
with either alkaline or lithium batteries. M. Data Communications Kit Data Communications Code
F. Battery Charger Options Battery Charger Code The FiveStar Link Communications Kit None 0
None 0 contains the software and adapter neces- FiveStar Link 1
From wall adapters to vehicular chargers,
8-24VDC (Vehicle) 1 sary to download the instrument datalog
you can recharge your batteries wherever
110 VAC 2 or change the instrument setup options.
you need. Also, the unique Fast Charger
offers the best technology available in safe, 220 VAC 3 N. Packaging Options & Carrying Cases
rapid charging of your NiCd battery packs. Packaging & Carrying Cases Code
110 VAC and Vehicle 4
For a small investment, the Fast Charger You can further protect your FiveStar Alarm Std shipping container only 0
Fast Charger (NiCd only) 5
not only fully charges in less than five with optional carrying cases. For ease of Black plastic case 1
Fast Charger (NiMH and NiCd) 6 transport and handling, these cases can be
hours, it also pays for itself by ensuring the Heavy duty case with video 2
longest possible life from your rechargeable even be ordered to accommodate calibration Large, heavy duty case with 3
packs. accessories.With the premium cases, a sim- video & space for cylinder
ple to understand training videotape is
G. Sampling and Calibration Methods Sampling/Cal. Methods Code Orange plastic case 4
included at no extra charge.
The FiveStar Alarm’s sampling systems None 0
provide the highest degree of protection Aspirator Pump Module A O. Instrument Case Selection Instrument Cases Code
available. The patented PulseCheck® Pump Calibration Cap C The FiveStar Alarm is offered in two case Nickel-plated 0
constantly checks the flow system for PulseCheck Pump P housings: standard, nickel-plated ABS or Stainless filled 1
changes in operation and will provide an stainless steel fiber-filled black ABS. The
alarm to the user if it senses a major standard nickel-plated version provides high-
change. You do need to have at least one er levels of Radio Frequency Interference (RFI)
pump, aspirator or calibration cap in your protection, whereas the stainless-filled ver-
“fleet” to calibrate your instruments. sion provides resistance against corrosion in
harsh chemical environments.
Your Model Part Number
Please write in numbers from selections above in appropriate boxes and
contact your Safety Products Distributor to place your order.
Selection A A A A B C D E F G H I J K L M N O
A-5ST- - 1 - - -
Orion® Multigas Detector
he Orion Multigas Detector is a Features
ow-cost, reliable, and easy-to-use
• One-button calibration • TIM ® System compatibility
portable instrument for detecting
• Long-life battery • Large, easy-to-read display
he presence of O2, H2S, CO and
ombustible gas. It will stand up to • Carbon-filled nylon case • Durable sensors
he roughest handling in even the • Tough, durable construction • Link™ Software compatibility
oughest environments. • Built-in pump
Approvals
he Orion Multigas Detector has been designed to meet intrinsic
afety testing requirements in certain hazardous atmospheres.The
Orion Multigas Detector has been approved by UL and cUL for use in
Class I, Division I, Groups A, B, C, and D.
Kit se
ase
Bla tion a Ca
Orion Multigas
y
yC
al Cap
ter
ra dur
ger ry
tL u m p
Detector Kits
om
at
ar tte
Bo con
Ca e Co
Ca ne B
Int atio
Or be
Ch a
1f e
& HB
n
ro
E
i
ali
g
r
ern
an
lib
tP
ck
lib
ot
M
S
Alk
10f
LEL
Ni
CO
H2
2
PartNo.
O
A. Combustible Sensor Options Combustible Sensor Code I. Sampling Probes Sampling Probe Code
To choose to have MSA’s own long-life 20L None 0 MSA’s sampling probes are durable and None 0
combustible sensor installed in your new % LEL (Pentane, 0–100%) 1 comfortable to use. The built-in Water Stop 1-foot straight 1
Orion Multigas Detector, choose selection filter ensures your sampling system is not 3-foot straight 2
1. For no combustible sensor, enter a “0.” contaminated with dirt and debris if the 3-foot, holes near tip 3
Oxygen Sensor Code probe tip is dipped in water. You must order 3-foot, holes near handle 4
B. Oxygen Sensor Option a probe if you order a sampling line as we
None 0 Hot-gas sampling probe 5
To choose to have an oxygen sensor strongly recommend you operate the
installed in your new Orion Multigas Oxygen (0–25%) 1 instrument with this filter in place.
Detector, choose selection 1. For no oxygen
sensor, enter a “0.” J. Carrying Attachments Belt Clip Code
While a high-strength, nylon clip is offered Standard nylon 0
C. Carbon Monoxide Sensor Option Carbon Monoxide Sensor Code with the instrument at no charge, a swivel Swivel belt loop 1
To choose to have a carbon monoxide sen- None 0 belt loop kit, which allows quick release
sor installed in your new Orion Multigas Carbon monoxide (0–999 ppm) 1 from your belt with a half turn, is also
Detector, choose selection 1. For no carbon available.
monoxide sensor, enter a “0.” Instrument Jacket Code
K. Instrument Jacket
D. Hydrogen Sulfide Sensor Option Hydrogen Sulfide Sensor Code For the highest levels of environmental and None 0
To choose to have a hydrogen sulfide sensor None 0 rough handling protection, you can order Black Rubber Boot B
installed in your new Orion Multigas Hydrogen sulfide (0–200 ppm) 1 from a variety of jackets and boots for your Black Leather Case L
Detector, choose selection 1. For no hydro- Orion Multigas Detector. Orange Cordura Jacket C
gen sulfide sensor, enter a “0.”
E. Battery Pack Options Battery Pack Code L. Calibration Kits Calibration Accessories Code
You can choose between MSA’s NiMH Standard NiMH rechargeable A You can choose one of two calibration None 0
rechargeable batteries which will run your (comes with standard AC charger) options for your Orion Multigas Detector. Model RP Calibration Kit 1
Orion Multigas Detector for up to 16 hours The flexible RP kit provides a constant flow Squirt Gas Check Kit 2
Replaceable alkaline B
in pump mode and 20 hours in diffusion regulator that is reused and provides the
Both NiMH and alkaline C greatest accuracy. The squirt gas test kit
mode, or you can choose the convenience
of alkaline batteries. For ultimate flexibility, provides a very economical means to verify
choose “both!” instrument calibration.
F. Battery Charger Options Battery Charger Code M. Data Communications Kit Data Communications Code
If you order your Orion Multigas Detector None/Standard AC charger 0 If you need to track the readings and None 0
with a rechargeable battery pack, the Vehicular charger 1 operation of your Orion Multigas Detectors, Orion link module 1
charger is included in the price. If you want consider ordering them with the optional Module and download 2
the optional vehicular charger adapter, built-in datalogging module. This option software
choose selection “1.” also provides STEL and TWA capabilities.
G. Sampling Methods Sampling Methods Code N. Packaging Options & Carrying Cases Packaging & Carrying Cases Code
The Orion Multigas Detector’s patented None D Std shipping container only 0
You can further protect your Orion Multigas
Pulsecheck™ pump technology leads the Integral, Pulsecheck pump P Detector with optional carrying cases. For Black plastic case w/space 1
industry. If you chose the built-in pump, Manual aspirator module A ease of transport and handling, these cases for cylinder, with video
operating directly off the instrument bat-
can be even be ordered to accommodate Heavy duty case with video 2
teries, you are assured of an audible pump
calibration accessories.With the premium Large, heavy duty case with 3
fault alarm and you do not need to main-
cases, a simple to understand training video and space
tain a second set of batteries. If you are
videotape is included at no extra charge. for 2 cylinders
ordering diffusion instruments, a calibra-
tion cap will be included to calibrate your Orange plastic case 4
instruments. w/space for cylinder,
with video
H. Sampling Lines Sampling Lines Code
materials guaranteed to not alter sample None 0
concentration. Screw fittings with O-Ring 3-foot coiled 1
couplings at each end ensure there are no 5-foot coiled 2
leaks when the system is operating.
10-foot 3
15-foot 4
25-foot 5
Selection A B C D E F G H I J K L M N
A-ORION- - - - - - - - - - - - - -
Solaris™ Multigas Detector ne w!
he Solaris Multigas Detector is an affordable, durable, reliable, easy-to-use portable instrument for detecting the
resence of O2, H2S, CO and combustible gas. It is designed to withstand rough handling in harsh environments.
est of all, it delivers MSA’s commitment to quality at the smallest size and, even smaller price.
Features
rgonomic Design Lightweight TIM System Compatible
or maximum comfort. Under 8 oz., compact size that Compatibility for computer
makes it easy to wear. automated calibration and
Alarm System record-keeping.
Durable
World-class triple alarm system Sampling Pump Option
with 100+ decibel audible alarm, Case with rubberized armor
multiple high-intensity visual provides superior protection Optional powered sampling
larm and strong vibrating alarm. against liquid and dust ingress pump with extensive contaminant
(IP 65 rated. filtering system.
DisplayFeatures
Long-life Battery W arranty
uperior display features simulta-
eous gas concentration display, Rechargeable lithium ion battery Outstanding 2-year, all-inclusive
acklighting for easy reading and provides 14+ hours of continuous warranty.
lphanumeric message bar for run time and delivers best-in-
asy use. class performance in extreme
conditions.
Solaris Kits
Basic Kits Industrial Kits (includes Econo-cal calibration kit)
-Gas Instrument 10048148 4-Gas Instrument 10049293
-Gas (LEL, O2, CO) 10048150 3-Gas (LEL, O2, CO) 10049294
-Gas (LEL, O2, H2S) 10048211 3-Gas (LEL, O2, H2S) 10049295
-Gas (LEL, O2) 10048213 2-Gas (LEL, O2) 10049296
Standard Kits (includes datalogging option)* Deluxe Kits (includes Econo-cal calibrationkit, datalogging &
-Gas Instrument 10048147 sampling pump)*
-Gas (LEL, O2, CO) 10048149 4-Gas Instrument 10049297
-Gas (LEL, O2, H2S) 10048212 3-Gas (LEL, O2, CO) 10049298
-Gas (LEL, O2) 10048214 3-Gas (LEL, O2, H2S) 10049299
2-Gas (LEL, O2) 10049300
Selection A B C D E F G H I
Watchman® Multigas Monitor
he Watchman Multigas Monitor is a durable, portable instrument used to detect
nd monitor combustible gases, oxygen, and toxic gases in workplace atmospheres,
specially in confined spaces such as manholes, storage tanks, tank cars, vaults, mines,
nd sewers. Designed for rugged handling, the monitor incorporates the state-of-the-art
echnology in a strong aluminum housing.The Watchman Monitor is ideal for long jobs in
eavy industrial environments, as the instrument will run up to 16 hours on a single charge.
or more complete information, see Data Sheet 08-02-39.
Approvals
he Watchman Multigas Monitor meets intrinsic safety testing requirements for use
n Class I Division 1, Groups A, B, C and D; Class II Division 1, Groups E, F, G; and Class III
azardous locations.
Watchman Multigas y
g
/Ta r op
Monitor Kits isp
la
/T WA arge Line
h e er St rap
T
10 Pro W a Line
D S ak EL C C ft b t
LEL O 2 CO H2 Pe ST A PartNo. Notes
ndustrial 4-Gas • • • • • • • • • 711132
ndustrial 4-Gas • • • • • • • • • • 711406
ndustrial 3-Gas • • • • • • • • • 711407 Replaces Model 360
ndustrial 3-Gas • • • • • • • • • 711408 Replaces Model 361
ndustrial 2-Gas • • • • • • • • 711409 Replaces Model 260
A. Electrochemical Sensor Configuration Sensors (Select 4) Code H. Sampling Lines Sampling Lines Code
Options Sulfur Dioxide (0-100 ppm) 6 The Watchman Monitor’s sampling lines are None 0
Please list the code number for the toxic gas Nitrogen Dioxide (0-100 ppm) 5 of the highest quality materials guaranteed 5-foot 1
sensors desired in the spaces to the right. In Nitric Oxide (0-100 ppm) 4 to not alter sample concentration. The 10-foot 2
order to properly process your order: Hydrogen Sulfide (0-200 ppm) 3 heavy-duty synthetic rubber material is 15-foot 3
• list them in descending order Carbon Monoxide (0-2000 ppm) 2 ideally suited to industrial applications 25-foot 4
• use zeros to fill any remaining Oxygen (0-25%) 1 where heat and chemical resistance are 50-foot 5
selections (example: 2100) crucial to instrument performance. Screw
None 0
• add the price of each sensor to obtain fittings with O-Ring couplings at each end
the sensor sub-total pricing help reduce the possibility of leaks when the
monitor is operating.
B. Combustible Gas Sensor Options Sensors Code
If a combustible gas sensor is desired, None 0 I. Sampling Probes Sampling Probes Code
select type of display. There are two options 0–5% CH 4 (Methane) M MSA’s sampling probes are durable and easy None 0
available: 0–100% LEL Pentane L to use. An assortment of probe types is avail- 18-inch plastic 1
0-5% Methane (%CH4) or able to suit your applications. You can select 3-foot brass 2
0-100% Lower Explosive Limit (%LEL) between heavy-duty nickel plated brass 3-foot plastic 3
probes or phenolic plastic probes where 4-foot solid brass 4
C. Peak Page Peak Page Code electrical conductivity might be a concern.
Allows user to view the peak gas readings Not enabled 0
J. Line Traps Line Traps Code
for the entire time the instrument is run- Peak display enabled 1
ning. The user can access this page by press- The Watchman Monitor is offered with two None 1
ing simply the “PAGE” button on the tester types of sample line protection from water Water Stop 2
keypad. ingress: a water stop filter and a water trap. Line Trap Assembly 3
The convenient, easy-to-use in-line water Both 4
D. STEL Page STEL Page Code stop filter is a membrane filter that will
Enables page and alarms for 15-minute- Not enabled 0 prevent liquids from being drawn into the
weighted-average gas exposures. To enable STEL display enabled 1 instrument. The water trap provides a water
the STEL page, enter a “1” in the box to the collection bulb with a stop to automatically
right, otherwise, enter a “0”. cut off the pump flow when the bulb fills.
The water trap provides a visual indication
E.TWA Page TWA Page Code you are drawing water into your sampling
Enables page and alarms for 8-hour- Not enabled 0 lines.
weighted-average gas exposures. To enable TWA display enabled 1
the TWA page, enter a “1” in the box to the K. Remote Alarms Remote Alarms Code
right, otherwise, enter a “0”. The Watchman Monitor’s remote alarms None 0
F. Datatagging Page TAG Page Code provide an additional level of audible and 90-dB horn / 3-foot cable 1
Allows user to enter a text “tag” using the Not enabled 0 visual alerts to your gas monitoring 90-dB horn / 15-foot cable 2
keypad to denote a location or note with a program. Available in low- and high-sound 105-dB horn / 3-foot cable 3
Datatagging pages enabled 1
time stamp. To enable the datatagging output and with an optional 15-foot exten-
sion cable, the remote alarms ensure your 105-dB horn / 15-foot cable 4
page, enter a “1” in the box to the right,
otherwise, enter a “0”. team is notified in high-noise areas.
G. Battery Charger Options Battery Charger Code L. Packaging Options Packaging Options
From wall adapters to vehicular chargers, None 0 You can further protect your Watchman Standard packaging 0
you can recharge your batteries wherever Vehicle, 8–24VDC 1 Monitor with a high-strength, weatherproof Premium field case with 1
you need. Once recharged, your Watchman Single-unit 110 V 2 carrying case. For ease of transport and compartments for calibration
monitor is ready to provide you with up to handling, the premium case accommodates accessories and bonus
Single-unit 220 VC 3
15 hours of continuous gas monitoring. the instrument along with its sampling and training video
Five-unit, 110/220 VC 5
calibration accessories. A simple-to-under-
stand training videotape is included at no
extra charge. (Standard packaging shown.)
Selection A A A A B C D E F G H I J K L
A-WTM- - - - - - -0
List sensors in descending
numerical order.
Passport® Personal Alarm
MSA’s Passport Personal Alarm is the world’s top-selling For more complete information, please
multigas detector, with over 50,000 shipped to customers refer to Data Sheet 08-00-39.
worldwide. Its durability is field-proven in the toughest
ndustries around the globe. As the first gas detector with Approvals
mplified three-pushbutton operation, the Passport
The Passport Personal Alarm has been
ersonal Alarm set the standard for simplicity, and users
approved for use in Class I Division 1,
ypically require less training to operate it.
Groups A, B, C and D; Class II Division 1,
he Passport is packed with the features needed to help Groups E, F, G; and Class III hazardous
nsure worker safety. Capable of monitoring up to five locations.
ases simultaneously, it is equipped with bright, multidi-
ectional alarm lights and a loud alert horn.The display
aces the user, allowing hands-free operation when worn Assemble-to-Order (ATO) System:
n the belt or on a strap around the neck.The Passport You Make the Choices
larm’s optional high-efficiency pump is powered by the The ATO System makes it easy to “custom order” the Passport Personal Alarm, configured exact-
nstrument, which provides audible and visual alerts in the ly the way you want it.You can choose from an extensive line of base instrument components
vent of flow faults.The pump can be removed to provide and accessories. To obtain a copy, request Bulletin 0808-03-MC. To obtain a copy of the ATO via
iffusion-mode operation.The instrument also records gas FAX, call MSA QuickLit Information Service at 1-800-672-9010. At the prompt, request QuickLit
xposure readings for up to 12 hours for later retrieval if Document #2390 (ATO for MicroGard Portable Alarm).
ecessary.
be Forafull
y ro
Passport Alarm Kits tP ket t
g er er p descripton
Kit
A / harg e Ba Pu m lPu ne/1 Jac acke Cas ase Test
Ta tt p m f e
y ofthe
la W
isp T C in n ra Li ge J ge C
D S ak TEL/ iCd/ lkal dd-o nteg 10ft ran lack ran lack Bump Fi
veStar
LEL O 2 CO H2 Pe S N A A I O B O B PartNo.
Alarms
ndustrial 4-Gas • • • • • • • • 711403 accessories,
ndustrial 4-Gas • • • • • • • • • • 711404 please refer
ndustrial 4-Gas • • • • • • • • 803912 to pages
ndustrial 3-Gas • • • • • • • 711405 79—80.
ndustrial 3-Gas • • • • • • • 803913
See pages
ndustrial 3-Gas • • • • • • • 803894 96—100 for
ndustrial 4-Gas • • • • • • • • • • • 711129 calibration
ndustrial 4-Gas • • • • • • • 801092 accessories.
ndustrial 3-Gas • • • • • • • • • • • 711131
ndustrial 3-Gas • • • • • • 803892
ndustrial 3-Gas • • • • • • • • • • • 711130
To obtain a copy of either ATO via FAX, call MSA QuickLit Information Service at
1-800-672-9010. At the prompt, request QuickLit Document #2391 (ATO for
Passport PID II Organic Vapor Monitor), or request QuickLit Document #2245
(ATO for Passport VOC 2000 Monitor).
For further information on PassportPIDII and VOC 2000 accessories,please refer to Passport® PID II Monitor in action
pages 67—68.
Features
Multi-Function Flexibility Tough, Durable Construction
indoor or outdoor (or both) • excellent resistance to penetration
configure any combination of gases from water and dust
including O2, CO and H2S • weather-resistance rating of IP54
for low-level leaks, 0-100% LEL or
CH4 0-100% by volume Large, Easy-To-Read Display
• one of the largest displays of any
ar-Hole Probe Filter Trap multigas detectors on the market
bar-hole probe filter trap is designed to • backlighting provides exceptional Orion® G Multigas
keep out water and dirt contrasts and Leak Detector
"quick connect" feature allows user to with Flexible Probe
attach probe or sampling line while TIM¤ Compatibility
minimizing the possibility of air leaks
• TIM® (Total Instrument Manager)
System allows users to automatically
uperior Design calibrate their instruments and track
calibration records.
sensor is located on the end of a flexible Orion® G Multigas and Leak
gooseneck probe, thereby allowing Detector with Coiled Probe
sensor to be placed closer to item being Built-InPump
tested
• built-in pump for remote sampling of the
super-fast response time
environment and fast response to leaks.
fits easily and comfortably in the hand
intrinsically safe.
k n e se
ac k io Ca
e
de ide ry P Pac er t ct Lin
as
i e ry
ar
C
ong-Life Battery ox ulf te y rg ec n
n
ng Ki
t
OrionG Multigas and on n S Bat tter ha nn Co pli e
a
t n ing tic C
ur
o
accommodates either a NiMH battery Leak Detector Kits
o
or
M e a C o ed m b o t i g s
L gen on rog line h B cle k C ad Sa ro k B ra og Pla
C
pack or alkaline batteries ib al
Flexible Probe LE xy arb yd lka im ehi uic hre 0 ft ft P lac
w
al at ed
lo
provides up to 16 hours of continuous
l
O C H A N V Q T 1 1 B C D R
Ye
%
instrument operation Deluxe 4 gas 10041504 • • • • • • • • • • • • • •
Deluxe 3 gas (H2S) 10041505 • • • • • • • • • • • • •
urable Sensors
Deluxe 3 gas (CO) 10041506 • • • • • • • • • • • • •
MSA Series 20L sensor provides up to
Industrial 4 gas 10041507 • • • • • • • • • •
50 times the silicone poison tolerance,
considerably expanding sensor Industrial 3 gas (H2S) 10041508 • • • • • • • • •
service life
Industrial 3 gas (CO) 10041509 • • • • • • • • •
fast-reacting, solid-state 20G sensor in
tip of probe Economy 4 gas 10041510 • • • • • • • •
all sensors are easy to maintain Economy 3 gas (H2S) 10041511 • • • • • • •
Economy 3 gas (CO) 10041512 • • • • • • •
One-Button Calibration
Supereconomy 4 gas 10041513 • • • • • •
calibration is accomplished with
Supereconomy 3 gas (H2S) 10041514
push of a single button (with appropriate • • • • •
calibration gas) Supereconomy 3 gas (CO) 10041515 • • • • •
For further information on Orion G Detector accessories,please refer to pages 67—68.See pages 82—86 for calibration accessories.
A. Combustible Sensor Options Combustible Sensor Code I. Sampling Probes Sampling Probe Code
To choose to have your MSA 20L % LEL (Methane, 0–100%), 0 MSA’s sampling probes are durable and None 0
combustible sensor gas reading factory Flexbile probe comfortable to use. The built-in Water Stop 1-foot straight 1
set to be displayed as %LEL or %Volume, % Volume (0–100%), Flexbile probe 1 filter ensures your sampling system is not 3-foot straight 2
enter a selection for display reading and contaminated with dirt and debris if the Bar hole probe 3
probe type. % LEL (Methane, 0–100%), 2 probe tip is dipped in water. You must order
Coiled probe 8-inch Stix 4
a probe if you order a sampling line as we Hot gas probe 5
% Volume (0–100%),Coiled probe 3 strongly recommend you operate the
instrument with this filter in place.
B. Oxygen Sensor Option Oxygen Sensor Code Sampling connection method chosen above
To choose to have an oxygen sensor None 0 determines type of fitting supplied with
installed in your new Orion G Multigas and Oxygen (0–25%) 1 sampling line.
Leak Detector, choose selection 1. For no
oxygen sensor, enter a “0.” J. Carrying Attachments Belt Clip Code
While a high-strength, nylon clip is offered Standard nylon 0
C. Carbon Monoxide Sensor Option Carbon Monoxide Sensor Code with the instrument at no charge, a swivel Swivel belt loop 1
To choose to have a carbon monoxide sen- None 0 belt loop kit, which allows quick release Pistol grip 2
sor installed in your new Orion G Multigas Carbon monoxide (0–999 ppm) 1 from your belt with a half turn, is also
and Leak Detector, choose selection 1. For available. For easier one-hand operation,
no carbon monoxide sensor, enter a “0.” choose the pistol grip option.
D. Hydrogen Sulfide Sensor Option Hydrogen Sulfide Sensor Code K. Instrument Jacket Instrument Jacket Code
To choose to have a hydrogen sulfide sen- None 0 For the highest levels of environmental and None 0
sor installed in your new Orion G Multigas Hydrogen sulfide (0–200 ppm) 1 rough handling protection, you can order a Black rubber boot B
and Leak Detector, choose selection 1. For jacket or boot for your Orion G Multigas Yellow cordura jacket C
no hydrogen sulfide sensor, enter a “0.” and Leak Detector. Both boot and jacket D
E. Battery Pack Options Battery Pack Code
You can choose between MSA’s NiMH L. Calibration Kits Calibration Accessories Code
Standard NiMH rechargeable A
rechargeable batteries which will run your You can choose one of two calibration None 0
(comes with standard AC charger)
Orion G Multigas and Leak Detector for options for your Orion G Multigas and Leak Model RP Calibration Kit 1
Replaceable alkaline B
up to 16 hours, or you can choose the con- Detector. The flexible RP kit provides a (includes gas cylinder)
venience of alkaline batteries. Also avail- Replaceable alkaline with C
constant flow regulator that is reused and Squirt Gas Check Kit 2
able in easy-to-change alkaline with thumbscrew attachment
provides the greatest accuracy. The squirt (includes gas cylinder)
thumbscrew attachment. gas test kit provides a very economical
F. Battery Charger Options Battery Charger Code means to verify instrument calibration.
If you order your Orion G Multigas and None/Standard AC charger 0 M. Data Communications Kit Data Communications Code
Leak Detector with a rechargeable battery Vehicular charger 1 If you need to track the readings and None 0
pack, the charger is included in the price. If operation of your Orion G Multigas and Orion link module 1
you want the optional vehicular charger Leak Detectors, consider ordering them Module and
adapter, choose selection “1.” with the optional built-in datalogging download software 2
Sampling Connection Methods Code module. This option also provides STEL and
G. Sampling Connection Methods TWA capabilities.
The Orion G Multigas and Leak Detector Threaded A
offers the flexibility of using standard Quick-connect B N. Packaging Options & Carrying Cases Packaging & Carrying Cases Code
threaded connections or the new Quick- You can further protect your Orion G Std shipping container only 0
Connect air-line fittings. Multigas and Leak Detector with optional Black plastic case with video 1
carrying cases. For ease of transport and and space for 2 cylinders
H. Sampling Lines Sampling Lines Code handling, these cases can be even be Heavy-duty case with video 2
MSA’s high-speed sampling lines are of the None 0 ordered to accommodate calibration acces- and space for 2 cylinders
highest quality materials guaranteed to 3-foot coiled 1 sories.With the premium cases, a simple to
not alter sample concentration. Threaded 5-foot coiled 2 understand training videotape is included
fittings with O-Ring couplings at each end 10-foot 3 at no extra charge.
ensure there are no leaks when the system 15-foot 4
is operating. Also available in a Quick-
25-foot 5
Connect version for easy attaching and
5-foot 6
tight seal. Sampling connection method
chosen above determines type of fitting
supplied with sampling line.
Selection A B C D E F G H I J K L M N
A-ORION G- - - - - - - - - - - - - -
Combustible Gas Indicators
Gascope® Combustible Gas Indicators and
Tankscope® Combustible Gas Indicator, Model 62T
Gascope Combustible Gas Indicators are portable instruments for use in detecting,
measuring, and pinpointing leaks of combustible gases and vapors. Each unit is easily
arried with integral neck and waist straps, leaving hands free for climbing, operating
he instrument, or carrying additional equipment.
hree Gascope Combustible Gas Indicator models are available.The Model 60 is
esigned for use by gas utility companies in routine testing for methane-in-air
oncentrations in manholes, sewers, curb boxes, and other street openings.The
Model 62S, also suitable for use by gas utility companies, is designed for reading
–100% LEL methane-in-air and 0–100% by volume methane-in-air.The Model 62 is
or general industrial use and is designed for reading 0–100% LEL pentane-in-air. For
more complete information, see Data Sheet 08-01-04.
he Tankscope Combustible Gas Indicator, Model 62T, is a portable instrument
Gascope® Combustible Gas Indicator
pecifically designed to detect combustible gas leaks in inerted shipboard oil holds.
ased on the highly successful Gascope Combustible Gas Indicator, the portable
ankscope Indicator has an easy-to-read analog display and is very simple to use. Approvals
Gascope Combustible Gas Indicators are listed by MET for use in
Gascope/Tankscope Indicators Class I, Division 1, Groups C and D hazardous locations defined by the
Complete with carrying straps and batteries,less sampling line. National Electric Code.
Utility Model 60 465475
Model 62 465681
Utility Model 62S 468410
Model 62T,Tankscope 711258
pprovals
Model 2A is listed by Underwriters’Laboratories (UL) for use in hazardous locations as defined by
he National Electrical Code. UL approval is for Class I, Group D, Divisions 1 and 2; and Class I, Groups
, B and C, Division 2 (Division 1 excluded), hazardous atmospheres. Explosimeter® Combustible Gas Indicator
xplosimeter Indicator
omes complete with carrying straps, less sampling line.
escription Applications Part No.
Model 2A General testing for combustible gases or vapors in the air 89220
Batteries
FiveStar FiveStar Passport,
Batteries Black ABS Ni-Plated Orion PID II,VOC 2000 Watchman MicroGard Orion G
Rechargeable NiCd 710427 10008606 — 496990 814127 478510 —
Heavy-Duty NIMH 10008642 10013145 10031091 800527 — — 10031091
Replaceable “AA” 710955 10008607 10031092 800526 — 482245 10031092
Replaceable, w/thumbscrews — 711041 10042020 — — — 10042020
Battery Pack Jack Cover — — — — — — 10030901
Remote Alarms
he Remote Alarm gives added audible alarm capability to many MSA portable gas monitors (listed below).
n alarm condition triggers both the Remote Alarm and the gas monitor’s alarm. In addition, two red LEDs on the
emote Alarm will light.The alarm is for workers wearing hearing protection or to alert standby personnel outside a
onfined space.Two versions are available: 90-decibel where hearing protectors are not worn, and
05-decibel if hearing protectors are worn (dB levels measured at one foot). Operates on one 9V alkaline battery.
emote Alarms forPassport
, PID I,IMicrogard, and W atchman Instruments
0dB Horn 800992
05dB Horn 800991
5-ft extension cable (total length must not exceed 300 ft) 800365
dapter cable (required) for Passport, Passport PID II, and MicroGard 812706
PULSAR™+ Single-Gas Detector
The PULSAR+ Single-Gas Detector is reliable, easy-to-use, and
durable.With sensor options for CO, H2S and O2 , this unit will provide industry-leading
performance and stand up to the roughest handling in the toughest environments.
Industry-Leading Features
Easy-to-Read Display Replaceable Sensor
The PULSAR+ Single-Gas detector offers MSA-built, patented Button™ Sensors
the simplest, easiest-to-read display. Its are easily replaceable.The stainless steel,
large numeric display—one of the largest solid electrolyte construction sensors
on the market—features a backlight that contain no liquid, eliminating the
provides excellent contrast.The easy-to- possibility of sensor leakage.The
understand display icons help the user to extremely small and thin sensor profile
easily identify STEL,TWA and peak gas allows the PULSAR+ Single-Gas Detector
concentration levels at a glance. to deliver high performance in a very
compact package. Specifications
One-Button Autocalibration Gas Type CO H2S O2
Durability Range 0-500 ppm 0-200 ppm 0-25% O2
Intuitive, completely automatic calibra- Resolution 1 ppm 1ppm 0.1% O2
tion with the press of a button helps to The PULSAR+ Single-Gas Detector is
Response Time T90<60 sec T90<60 sec T90<35 sec
prevent improper calibration. No sepa- designed to withstand even the harshest
rate, easy-to-lose accessories are needed conditions and usage.The interlocking
for gas-response testing or instrument gasket that provides water resistance also
calibration. Simply attach the tubing to absorbs some of the shock when Pulsar+ Single-Gas Detector
the sensor inlet and apply gas. dropped, its solid-state and rugged case Instrument Type Part Number
design increase impact resistance and CO 10036171
Distinctive Alarm System minimize the chance for breakage. CO with vibrating alarm 10036174
H2S 10036172
A triple alarm system leaves no doubt for W ater & Dust Resistance H2S with vibrating alarm 10036175
the user in an alarm situation.The audio
alarm is piercing and distinctive so that it With its IP54 rating, the PULSAR+ Single- O2 10036170
cannot be confused with other common Gas Detector is highly water- and dust- O2 with vibrating alarm 10036173
workplace sounds.The best-in-class visual resistant.The simple, yet effective design
alarm features four multi-directional, features an interlocking single-gasket
super-bright LED displays located on the suspension system, providing a tight seal
top of the instrument so it can be seen and making it one of the most water- and
from all angles.The alarm status is also dust-resistant instruments in its class.
shown in the numeric display. An optional
vibrating alarm emits a strong, pulsing User Configuration
vibration that further calls attention to
the user when in alarm mode.The vibra- The PULSAR+ Single-Gas Detector
tor is strong enough to be felt through features fully adjustable warning, peak,
heavy work clothes. STEL and TWA alarm levels. STEL and TWA
function can be deactivated. All alarm
Clip Options and calibration gas value settings are
password protected.
With options for suspender- and cell
phone-style clips and lanyards, MSA’s Large Rubber Button
unique clip designs keep the unit
attached during even the roughest use. Large rubber buttons make the PULSAR+
Single-Gas Detector easy to operate, even
with gloves.The button labels feature
English text and international icons.
Pulsar™ Single-Gas Detector
he MSA PULSAR Single-Gas Detector provides
maintenance-free, 24-month monitoring for the detection of CO, H2S, or O2.With a
nique design combined with a competitive price, it is the clear choice in single-gas
etectors.
PULSAR Single-Gas Detector Assemble-To-Order System
elect instrument options and mark them in the boxes to the right.
ccessories
attery charger and stand 10040783
arrying case with strap 10035638
Model RP cylinder, pentane 804532
Model RP cylinder, methane 491041
Approvals
ETL (an OSHA-NRTL); Class I; Division 1; Groups A, B, C and D.
For more complete information, see Bulletin 0802-16-MC.
Detector Tube Pumps
Toximeter™ II Automatic Kwik-Draw®
Detector Tube Pump Detector Tube Pumps
The Toximeter II Automatic Detector Tube MSA’s Kwik-Draw and Kwik-Draw
Pump makes the sampling process easier, Deluxe Pumps can be used with an
allowing the user to preset the number of assortment of MSA’s detector tubes to
pump strokes (from 1 to 250 pump spot-test atmospheres for a wide vari-
trokes). Intrinsically safe, the automatic ety of toxic substances.They are
pump works with all MSA detector tubes. designed for one-hand operation and
t can also be used as a sampling pump. consistent delivery of a sample draw
volume of 100 milliliters (ml).
oximeter II Automatic
Detector Tube Pump 655585 For more complete information, see
Data Sheet 08-00-02.
or more complete information, see Data
Sheet 08-01-02. Kwik-Draw Basic Pump, with remote sampling adapter
and carrying pouch 488543
Kwik-Draw Deluxe Pump, with remote sampling adapter,
carrying pouch and end-of-stroke indicator 487500
Accessories
Gas-Tester™ II H
Sampling line, 10 ft 73067
Detector Tube Sampling line, 25 ft 73068
Pump Sampling line, 50 ft 73069
The Gas-Tester II H Pump is Remote Sampling Adapter, required for above sampling line 87970
et for action by compress- Solvent-Resistant Sampling Line, 25 ft, with reel 488780
ng the bellows. A pump Tube Holder, required for 488780 line above 488872
troke is started by press- Flue Gas Kit 470321
ng the release button.When the sample (100ml) is drawn through the tube,
he end-of-stroke indicator changes color. An accurate measurement is
obtained because the sample draw procedure itself is controlled only by the Detector Tube Handbook
pecifications of the pump and the flow resistance of the detector tube.
Detector Tube Handbook 813929
Gas-Tester II H Pump 696944
A - TIM - -
1 2 3 4
Calibration
Regulators
25/1.5LPM Flow Cont
rol Natural Gas Demand Regulator
Model RP Cylinder .25 lpm* 467895
This low-pressure Demand Regulator is designed to
Model RP Cylinder 1.5 lpm 467896
be used with MSA Instrument Calibration Systems
to supply 100% natural gas.The Demand Regulator
Can be used with chlorine and ammonia; replaces
will automatically supply 100% natural gas to the
N 809945.
calibrator as required. No adjustments are necessary or provided. Like the Gas
Miser Regulator, the Natural Gas Regulator features an automatic ON/OFF
valve that releases gas only on demand. Comes complete with (barb type)
Model RP outlet fitting and easily connects to natural gas supply with W" NPT thread.
Recommended for use with pressure of 0.3 to 5.0 psig.
Gas Miser¤ Demand Regulator: Natural Gas Demand Regulator 710545
he IntelligentRegulator
he Gas Miser Regulator is the most advanced, yet simple- Model RPCombination Regulators
o-use calibration gas delivery system available. Made of
ickel-plated brass and polished aluminum (especially Two regulators in one.Trigger activation allows a
mportant for reactive gases), the Gas Miser Regulator can bump test or calibration check in the “SQUEEZE”
upply gas flow from 0.1 lpm to 3.0 lpm. But that’s only the mode or fixed-flow calibration in the up or
eginning. Designed for use with any MSA Model RP Gas Miser ® “LOCKED”position. Designed for use with all
alibration Cylinder except chlorine and ammonia*, the Model RP Model RP and Econo-Cal calibration cylinders.
as Miser Regulator features an automatic ON/OFF valve Supplied with calibration tubing and special
hat releases gas only on demand. So only the amount of fitting.
as needed to calibrate your MSA instrument is delivered
Model RP Combination Regulator, .25 lpm 711175
ccurately.When the calibration is complete, the Gas Miser
egulator shuts off automatically. And, for user conve- Model RP Combination Regulator, 1.5 lpm 711174
ience, the regulator can stay connected to the cylinder
here it remains in a ready state—making it ideal for such Gas Miser¤ Manifold
xed installations as work benches and calibration stations.
The Gas Miser Manifold is not only a cylinder
he Gas Miser Regulator also eliminates the need to Gas Miser® Model holder but it also incorporates a 4-station “bump
hange regulators to accommodate different instruments BD-20
test”or calibration manifold. It works with Model
r flow rates. It’s not only intelligent, it’s cost-efficient. RP and Econo-Cal cylinders and Gas Miser regula-
upplied with calibration tubing and special fitting. tor on any pumped or aspirated instrument.The
A Gas Miser Regulator for chlorine and ammonia is available for Model RP cylinders — manifold will supply the correct amount of gas
N 10034391 required and will bump test or calibrate up to four instruments
Model RP 710288 simultaneously. Gas Miser regulator sold separately.
Model RP, Chlorine and Ammonia 10034391 4-station Manifold 710274
Model BD-20, with CGA 590 fitting 710289
Calibration Gas
ach MSA Calibration Gas Cylinder is shipped with an MSA certifies that the gas mixture in calibration gas cylinders was prepared gravimetrically,
ndividual copy of a material safety data sheet (MSDS) using NIST traceable weights.The lot number and nominal value of the gas constituents in
nd an individual copy of a certificate of analysis. percent by volume, percent by mass, PPM, or volume are specified on the cylinder.The
uncertainty statement of the specified nominal value is also listed.
Model RP and Model R Calibration Cylinders Non-Reactive Gases,Steel Cylinder,100 Liters
100 LTRS 19 LTRS 34 LTRS
1000 PSI 300 PSI 500 PSI
Gas Fill Gas Mixture Background Model RP Model R Econo-Cal
Air air zero (THC < 1 ppm) — 801050 — —
Carbon 400 ppm carbon monoxide air 806255 — —
Monoxide 300 ppm carbon monoxide air 473180 461769 —
200 ppm carbon monoxide air 809243 — —
100 ppm carbon monoxide air 809242 — —
50 ppm carbon monoxide air 809241 — —
100 ppm carbon monoxide nitrogen 806734 — —
Hydrogen 0.8% hydrogen air 803102 — —
Isobutylene 100 ppm isobutylene air 494450 — 10048279
Model RP
Methane 2.5% methane air 491041 459942 —
6.6% methane nitrogen 801049 — — Model RP Cylinder
Oxygen 20.8% oxygen nitrogen 479857 468248 — Contents:Pressure 1000
5.0% oxygen nitrogen 493580 476302 — psig; approximately 100
Nitrogen 100% nitrogen — 481317 — — liters at atmospheric
Nitrous Oxide 10 ppm nitrous oxide nitrogen 806736 — — pressure
Size: 13-3 4" x 3"
Pentane 0.75% pentane (50% LEL) air 804532 — —
Weight: 2 lb 13 oz
Propane 0.6% propane air 493579 — —
Material: Steel
Combination 0.35% pentane, 19.0% oxygen, 100 ppm carbon monoxide nitrogen 10007047 — —
0.6% propane, 15% oxygen, 60 ppm carbon monoxide nitrogen 801051 — —
1.45% methane, 300 ppm carbon monoxide, 15% oxygen nitrogen 10010162 — —
2.5% methane, 60 ppm carbon monoxide, 15% oxygen nitrogen 813718 — —
2.5% methane, 300 ppm carbon monoxide, 15% oxygen nitrogen 10040291 — —
1.45% methane, 15% oxygen nitrogen 478192 — —
1.45% methane, 15% oxygen, 60 ppm carbon monoxide nitrogen 478191 — —
Model RP and Model Econo-Cal¤ Calibration Cylinders Reactive Gases,Aluminum Cylinder,58 & 34 Liters
58 LTRS, 500 PSI
Gas Fill Gas Mixture Background Model RP Econo-Cal
Ammonia 25 ppm ammonia nitrogen 814866 711078
Chlorine 10 ppm chlorine nitrogen 806740 711066
Hydrogen Sulfide 40 ppm hydrogen sulfide nitrogen 467897 711062
15 ppm hydrogen sulfide nitrogen 806253 711064
10 ppm hydrogen sulfide nitrogen 467898 711060
Nitric Oxide 50 ppm nitric oxide air 812144 711074
Nitrogen Dioxide 10 ppm nitrogen dioxide air 808977 711068
Model RP Econo-Cal
Phosphine 0.5 ppm phosphine nitrogen 710533 711088
Hydrogen Chloride 40 ppm hydrogen chloride nitrogen 710210 711080 Model RP Cylinder
Hydrogen Cyanide 10 ppm hydrogen cyanide nitrogen 809351 711072 Contents: Pressure 500
psig; approximately 58
Sulfur Dioxide 10 ppm sulfur dioxide air 808978 711070
liters at atmospheric
Combination 1.45% methane, 15% oxygen, 300 ppm carbon monoxide, nitrogen 804770 711058
pressure
Gas Cylinders 10 ppm hydrogen sulfide
Size: 13X" x 3"
1.45% methane, 15% oxygen, 300 ppm carbon monoxide, nitrogen 10048788 10048790 Weight: 1 lb 11 oz
20 ppm hydrogen sulfide
Material: Aluminum
1.45% methane, 15% oxygen, 60 ppm carbon monoxide, nitrogen 10045035 10048280
20 ppm hydrogen sulfide
Econo-Cal Cylinder
Contents: Pressure 500
1.45% methane, 15% oxygen, 10 ppm hydrogen sulfide nitrogen 804769 711056
psig; approximately 34
1.45% methane, 15% oxygen, 300 ppm carbon monoxide nitrogen 813720 711076 liters at atmospheric
10 ppm hydrogen sulfide
pressure
1.45% methane, 15% oxygen, 60 ppm carbon monoxide nitrogen 10048890 10048981 Size: 13X" x 3"
20 ppm hydrogen sulfide Weight: 1 lb 1 oz
2.5% methane, 15% oxygen, 20 ppm hydrogen sulfide nitrogen 10048889 10048888 Material: Aluminum
0.35% pentane, 19% oxygen, 100 ppm carbon monoxide, nitrogen 10007049 —
35 ppm hydrogen sulfide
Note: Reactive gases have an expiration date listed on each cylinder.This is to ensure the highest quality and accuracy for instrument calibration.Most cylinders
have an expiration date of 12 months.Check with MSA Customer Service for the exact shelf life of a particular calibration cylinder.
Model RPCalibration Cylinder Steel, Model BD-20 Calibration Cylinders
100% Methane Contents: Pressure 2200 psig; approximately 552 liters (20 cu ft) of gas at
ontents: Pressure 1000 psig; approximately 58 atmospheric pressure
ters of pure methane with odorant added to Size: 25" x 4W" Weight: 10 lb 9 oz Material: Steel
mell like natural gas in all commercial gas lines
ze: 8V" x 3" Weight: 1 lb 13 oz Gas Fill Gas Mixture Background Part No.
Material: Steel Methane 2.5% Methane, 15% Oxygen, 60 ppm Carbon Monoxide Nitrogen 710566
1.45% Methane, 15% Oxygen, 60 ppm Carbon Monoxide Nitrogen 710565
as Fill Gas Mixture Part No.
Air, zero Air, zero,THC<1 ppm — 710776
Methane 100% Methane 711014
quirt Gas Bump Test Kit, less cylinder, but with required fittings and adapters, complete with instructions 813411
Shelf life item. See note page 103. ** Requires calibration adapter.