Professional Documents
Culture Documents
PT and Fittings Exam 4 Thai
PT and Fittings Exam 4 Thai
Name……………………………… Date……………………………….
Fittings:
1. What is the MWP of a hose with a JIC swage end? (2 Marks)
แรงดันสูงสุดของ JIC hose อยูท่ ี่เท่าไหร่ ?
3. What is the name of the connection seen on our standard Air & Water hoses and what
two things are added to increase its safety? (3 Marks)
ชื่อของ Connection ที่ใช้ สำหรับ Air และ Water ของ Expro standard
และ อุปกรณ์ที่ใช้ สำหรับ เพิ่มความปลอดภัยในการต่อเข้ากัน?
MWP:
5. PTFE tape should be applied to what type of fitting? How many wraps and in what
direction? (3 Marks) เทปร่ อน ใช้ สำหรับ Fitting ชนิดใด และต้ องพันเทปร่ อนกี่รอบ ทิศทางใด?
Name: Size:
Tube: …….……………………….
Tube: ……………………………..
10. How can you visually identify a (female) HP Autoclave Port?(2 Marks)
B:
12. What shall be clearly stamped on all the NPT fittings that we are allowed to use?
(2 Marks) ค่าอะไรบ้ าง ที่จะต้ องเห็นบนตัว NPT Fitting เพื่ออณุ ญาติให้ใช้ได้?
13. What type of valve is better for venting pressure and why? (2 Marks)
วาล์ วชนิดได ที่ใช้ ในการ Venting pressure และเพราะอะไร?
Type:
Reason:
15. Identify 3 possible leak paths (not the two hydraulic connections) and remedial action on
the diagram on a closed Needle Valve. (6 Marks)
จำแนก 3 จุดของของวาล์ ว ที่จะสามารถ รั่ วได้ ?
Leak path 1:
Action:
Leak path 2:
Action:
Leak path 3:
Action:
16. Why should a PRV be included in a test set up and to what pressure? (1 Mark)
ทำไมต้ องติดตั้ง PRV ในระบบการทดสอบ และต้ องตังค่ าไว้ที่เท่ าไหร่ ?
Pressure Testing
2. Name the two most common (oil industry) units of pressure that are used to
measure pressure? (2 Marks)
ชื่อ หน่วย 2 ชนิด ที่ ใช้วดั Pressure?
4. Why must you apply pressure to the test piece in increments? (2 Marks)
ทำไมจึงต้ องเพิ่ม Pressure ไปยังอุปกร์ ที่ทดสอบ เป็ นระดับๆ?
5. What additional form should be completed when pressure testing outside test
bays? (1 Mark)
6. What should be considered when elevating a test piece to fill it with water? (2
Marks) ต้ องพิจณาอะไรบ้ าง เมื่อต้ องยก อุปกรณ์ที่จะทดสอบ เพื่อเติมน้ำ?
7. Where would you find out the test pressure of a piece of equipment? (3 Marks)
เราจะสามารถหาค่าแรงดันที่จะ ทดสอบจากอุปกรณ์ได้ อย่างไรบ้ าง?
8. What should you do if you spot a leak during a pressure test? (1 Mark)
สิ่ งที่ควรทำ หากพบว่ามีจุดรั่ว ในระหว่างการทดสอบแรงดัน?
9. What is the advantage of using filler bars for gas testing? (1 Mark)
วัตถุประสงค์ที่ต้องใช้ filler bars ในการใช้ ก๊าซในการทดสอบ?
10. Why is it important to remove all of the air from a test piece? (2 Marks)
ทำไมเราต้ องเอาอากาสออกจากอุปกรณ์ให้ หมดก่อนที่จะทำการทดสอบ?
11. What two documents should be reviewed before conducting a pressure test? (2
Marks)แบบฟอร์ มใดที่เราต้ องตรวจสอบ ก่อนที่จะทำการทำสอบแรงดัน?
12. Name 4 checks that should be done on an Analogue Chart Recorder prior to use.
(4 Marks) 4 สิง่ ที่ต้องตรวจสอบก่อนที่จะใช้ Analogue Chart Recorder?
13. Name 3 things to consider when venting and rigging down a pressure test. (3
Marks) 3 สิง่ ที่ต้องคำนึง เมื่อต้ อง venting และ rigging down?
MAWP:
MTP:
CITHP:
17. How many pressure monitoring devices should be included in a pressure test set
up? (1 Mark) มีอป
ุ กรณ์อะไรบ้ างที่ใช้ ดแู รงดัน ในระหว่างการทำสอบแรงดัน?