Professional Documents
Culture Documents
8351A
8250A
8240A
Operating Manual
Betriebsanleitung
Although the 8240A, 8250A, 8351A and 8260A can be used with- All issues concerning use with the network are explained
out the GLM™ software and control network, they only reach in detail in the System Operating Manual provided with the
their full potential when set up and calibrated using the GLM™ GLM™ Loudspeaker Manager software kit.
software. The setup is fast and consists of the following steps:
• Run a CAT5 (RJ45) cable from the monitor control network Connections
to the next monitor (see Figure 1). Each monitor is supplied with a mains cable, one 5 m GLM
• Run the final cable to control network input of the GLM network cable and an operating manual. Before connecting
Adapter device. up, ensure that the mains switch is off.
• Connect the GLM Adapter device to your computer USB
connector. The cable is a part of the GLM User Kit. “MAINS INPUT” Connector
Connect the mains supply to this connector.
Network
ON
2 OFF dB
Stand-alone user
connectors SWITCH BASS BASS DESKTOP TREBLE STORED AES/EBU CH. DRIVER MUTE SYSTEM LVL. SWITCH
interface switch
ROLL-OFF TILT TILT A B WF COAX -10 -20
1 ON 2
OFF -30
-2 dB -4 dB -2 dB -4 dB -4 dB dB
+2 dB -4 dB
160 Hz MANUAL ON + ON
groups 1 and 2
SUM A AND B
-6 dB -6 dB -2 dB CTRL OFF + OFF
Mains input
connector MAINS INPUT 230 V~
50 / 60 Hz 330 W
12 V
REMOTE
DIGITAL IN
AES/EBU
DIGITAL THRU
AES/EBU
ANALOG
IN
292-8260T-6
SERIAL NUMBER
MAGNETICALLY SHIELDED
MADE IN FINLAND www.genelec.com
Figure 2. Connectors and controls on the back panel of a 8260A. 8240A, 8250A and 8351A share the same layout but
without the 12 V trigger voltage connector.
“DIGITAL IN AES/EBU” Connector +22.0 dBu RMS on models 8351A and 8260A. When A/D con-
verter input clip occurs the front panel light turns momentarily
Use this female XLR connector for AES/EBU formatted digital red, indicating the overload condition.
audio input signals. This input is selected automatically when
a valid digital audio signal is present, and overrides the analog “CONTROL NETWORK” Connectors
input. Use these RJ-45 sockets to connect the monitor to the propri-
etary Genelec Loudspeaker Manager™ (GLM™) network only.
Depending on the digital hardware, transmission of a 192 kHz This connector is not Ethernet LAN compatible. Do not con-
sample rate is achieved using a double speed, single chan- nect to Ethernet LAN.
nel/cable interface. This is called dual-wire mode. In this case
one cable per channel is used and no channel selection is “12 V REMOTE” Connector (8260A only)
required. Dual-wire mode is automatically detected by the in- You can set up remote controlled powering up and down of
put stage. the 8260A with 12 V voltage connected to this connector. The
minimum current needed to actuate this function is 70 mA.
If the digital source device has a volume fader that controls
the digital level, it may be advantageous to lower the level
control either on the computer interface or on the monitor’s Front Panel Warning Light
back panel controls, which in turn will force the use of more of
the digital [bit] resolution in the volume control. Device LED action Meaning and resolution
“ANALOG IN” Connector Table 1. Monitor and subwoofer front panel light indications
Use this connector for analog audio signals. The maximum summary
input level is +7.0 dBu RMS on models 8240A and 8250A and
h ACOUSTIC
AXIS
Figure 3. The location of the acoustic axis is on the cen- Figure 4. Symmetrical layout and keeping the acoustic
terline of the monitor at the given height “h”. The acoustic axis clear from obstructions minimizes reflection surfaces
axis of the 8351A and 8260A is located at the center of and maintains accurate localisation because reflections
the coaxial driver. are symmetrical.
Max
60 cm Avo
m > 60 cid
Min 5 c m
Figure 5. Recommended distances from a single wall to Figure 6. Recommended monitor positioning for 5.1 multi-
the front baffle of free-standing monitors. Correct (green) channel audio reproduction
and not recommended (red).
Mounting Considerations
If a red warning light appears, turn the analog source down!
If the levels are already modest and a digital signal is being
Align the Monitors Correctly
used, ensure that there are no bit errors in the AES/EBU digital
audio data. Place the monitors so that their acoustic axes are aimed to-
wards the listening position (see Figure 3). Vertical placement
is preferable, as it minimises acoustical cancellation problems
around the crossover frequency.
Minimise Reflections
Acoustic reflections from objects close to the monitors like
desks, cabinets, computer monitors etc. can cause unwanted
colouration and blurring of the sound image. These can be mi-
nimised by placing the monitor clear of reflective surfaces. For
instance, putting the monitors on stands behind and above the
mixing console usually gives a better result than placing them
on the meter bridge. Symmetrical positioning of the reflec- Figure 8. Switch Group 1
tive objects is also important in order to maintain a balanced
soundstage (See Figure 4).
alignment of the acoustic axis. The stand can be attached to
Low Frequency Cancellations three mounting points allowing vertical and symmetrical hori-
In general, when a monitor’s front baffle is more than 0.3 me- zontal positioning.
ters (1 foot) away from the wall behind the monitor, a reflection
from this wall can cause a cancellation of low frequencies and Genelec 8240A, 8250A, 8351A and 8260A can be fitted to König
hence reduction of bass output. Distances between 1 and 2.2 & Meyer monitor mounts on two sets of M6x10 mm threaded
meters (3-7 ft.) should be avoided (See Figure 5). holes on the back of the enclosure. On the base of the 8240A
and 8250A enclosure is an M10x10 mm threaded hole which
As a rule of thumb, the lower the low frequency cut-off the can be used for securing the monitor to its base. Do not use
further away the monitor must be placed from the wall in order this thread for mounting the monitor on a microphone stand
to avoid this phenomenon. which has a 3/8” UNC thread. A wide variety of ceiling and wall
mounts are available through your Genelec dealer.
Distances to the ceiling and other walls may be shorter than the
distance to the wall behind a monitor. Reflections from these
surfaces may be important and should also be considered Setting the Input Sensitivity
The monitor level sensitivity functions for both analog and digi-
Operating Environment tal input. The sensitivity can be matched by adjusting the rotary
These monitors are designed for indoor use only. The permissa- Level control together with the System Level switches located
ble ambient temperature is 15-35 degrees Celsius (50-95°F) and in the switch group 2. (switches 6 and 7). The switches provide
permissable relative humidity between 20% and 80%. Humidity attenuation levels of -10 dB (sw. 6 ON), -20 dB (sw. 7 ON) and
condensation on the product is not allowed during use. If the -30 dB (both switches ON) The combined attenuation ranges
product has been stored or transported in a cool environment from 0 to -42 dB.
and then taken into a warm room, it must be allowed to warm
up completely before connecting to mains power. Functions On Switch Group 1
Sufficient cooling for the amplifier and functioning of the reflex (Tone Controls)
port must be ensured if the monitor is installed in a restricted Switch group 1 (the upper switch group) comprises the tone
space such as a cabinet, or integrated into a wall structure. controls that can adjust the frequency response of the sys-
The surroundings of the monitor must always be open to the tem in stand-alone mode to match the acoustic environment.
listening room with a minimum clearance of 5 centimeters (2”)
behind, above and on both sides of the monitor. The space Please note that the GLM software allows a much more ver-
adjacent to the monitor must either be ventilated or suffi- satile and precise set of controls to be used and supports the
ciently large to dissipate heat so that the ambient temperature fully automatic system alignment feature, the Genelec Auto-
does not rise above 35 degrees Celsius (95°F). Cal. Use the tone control switches on the monitor only if GLM
is not available for the system calibration.
Mounting Options
The vibration insulating Isolation Positioner/Decoupler™ (Iso- The controls are labelled “TREBLE TILT”, “BASS TILT”, “BASS
Pod™) table stand allows tilting of the monitor for correct ROLL-OFF” and “DESKTOP”. The factory settings for these
Safety Considerations
Maintenance Although the 8240A, 8250A, 8351A and 8260A have been de-
No user serviceable parts are to be found within the monitor signed in accordance with international safety standards, to
enclosure. Any maintenance or repair of the monitor should ensure safe operation and to maintain the monitor under safe
only be undertaken by a certified Genelec service. operating conditions, the following warnings and precautions
must be observed:
A 90
85 d 0° 15° 30°
B
DESKTOP LF 85
90 80 r
85 A 80
45°
80 90 75
BASS TILT 60°
85 70
80 65
BASS ROLL-OFF TREBLE TILT
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Figure 10. The curves above show the effect of the “Bass Figure 11. The upper curve group shows the horizontal
Tilt”, “Treble Tilt”, “Desktop Low Frequency” and “Bass directivity characteristics of the 8240A measured at 1 m.
Roll-Off” controls on the free field response of the 8240A. The lower curve shows the system’s power response.
Genelec Oy 8250A (dBr) vs freq (Hz) 17 Jan 06 Genelec Oy 8250A (dBr) vs freq (Hz) 17 Jan 06
100
d
B
r 90 95
A 90
85 d
0° 15° 30°
B
90 80 DESKTOP LF r 85
85 A 80
80 90 75
BASS TILT 45° 60°
85 70
80 65
BASS ROLL-OFF TREBLE TILT
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Figure 12. The curves above show the effect of the “Bass Figure 13. The upper curve group shows the horizontal
Tilt”, “Treble Tilt”, “Desktop Low Frequency” and “Bass directivity characteristics of the 8250A measured at 1 m.
Roll-Off” controls on the free field response of the 8250A. The lower curve shows the system’s power response.
Genelec Oy 8351A dBr) vs freq (Hz) 20 Nov 2014 Genelec Oy 8351A (dBr) vs freq (Hz) 20 Nov 2014
d 100
B
r 90 95
A
85 90
d
0° 15° 30°
B
90 80 DESKTOP LF r 85
85 A 80
80 90 75
BASS TILT 45° 60°
85 70
80 65
BASS ROLL-OFF TREBLE TILT
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Figure 14. The curves above show the effect of the “Bass Figure 15. The upper curve group shows the horizontal
Tilt”, “Treble Tilt”, “Desktop Low Frequency” and “Bass directivity characteristics of the 8351A measured at 1 m.
Roll-Off” controls on the free field response of the 8351A. The lower curve shows the system’s power response.
A 90
85 d
0° 15° 30°
B
DESKTOP LF 85
90 80 r
85 A 80
80 90 75
BASS TILT 45° 60°
85 70
80 65
TREBLE TILT
BASS ROLL-OFF
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Figure 16. The curves above show the effect of the “Bass Figure 17. The upper curve group shows the horizontal
Tilt”, “Treble Tilt”, “Desktop Low Frequency” and “Bass directivity characteristics of the 8260A measured at 1 m.
Roll-Off” controls on the free field response of the 8260A. The lower curve shows the system’s power response.
Figure 18. 8240A horizontal directivity plot. Figure 19. 8240A vertical directivity plot.
Figure 20. 8250A horizontal directivity plot. Figure 21. 8250A vertical directivity plot.
Figure 24 8260A horizontal directivity plot. Figure 25. 8260A vertical directivity plot.
90
d
B
r 85
A 80
75
20 50 100 200 500 1k 2k 5k 10k 20k 40k
Hz
10
Maximum peak SPL output per pair ≥ 115 dB SPL ≥ 120 dB SPL ≥ 121 dB SPL ≥ 123 dB SPL
on top of console at 1 m with music material
Maximum short term sine wave SPL output at (from 100 Hz to 3 kHz) (from 100 Hz to 3 kHz) (from 100 Hz to 3 kHz) (from 100 Hz to 3 kHz)
1 m on axis in half space, averaged as speci- ≥ 105 dB SPL ≥ 110 dB SPL ≥ 111 dB SPL ≥ 113 dB SPL
fied
Crossover frequency 3 kHz 1.8 kHz 470 Hz, 2.6 kHz 490 Hz, 2.6 kHz
Input signal
Analog 1 XLR female (10 kOhm input load impedance)
AES/EBU (single wire and dual wire) 1 XLR female (conforms to IEC 60958-4)
Digital audio
Word length 16 - 24 bits
Sample rate 32 - 192 kHz
Maximum analog input signal +7 dBu +7 dBu +21 dBu +21 dBu
Control network
Type proprietary GLMTM network
Connection 2 RJ45, CAT5 cables
Power consumption
Idle 14 W 17 W 20 W 26 W
Full output 110 W 170 W 290 W 330 W
Dimensions
Height 350 mm (1313/16 in) 433 mm (171/16 in) 433 mm (171/16 in) 570 mm (227/16 in)
Width 237 mm (93/8 in) 286 mm (111/4 in) 286 mm (111/4 in) 357 mm (141/16 in)
Depth 223 mm (813/16 in) 278 mm (1015/16 in) 278 mm (1015/16 in) 347 mm (135/8 in)
Height with Iso-Pod™ 365 mm (143/8 in) 452 mm (1713/16 in) 452 mm (1713/16 in) 593 mm (233/8 in)
Weight 9.4 kg (20.8 lb) 14.6 kg (32 lb) 19 kg (42 lb) 27.5 kg (60.5 lb)
* The notch and shelving filters adjustments, AutoCalTM and GLMTM manual system calibration features are part of the Genelec Loudspeaker Manager (GLMTM) software
11
12
GLM Kontroll- 1 ON
OFF
-10
-8
-6
-4
-2
Stand-Alone Pegelsteller
-12 0
ON
2
Netzwerk- OFF dB
Stand-Alone
Buchsen SWITCH
1
BASS
ROLL-OFF
BASS
TILT
DESKTOP TREBLE
TILT
STORED AES/EBU CH. DRIVER MUTE SYSTEM LVL.
A B WF COAX -10 -20
SWITCH
2
-2 dB -4 dB -2 dB -4 dB -4 dB
160 Hz
+2 dB -4 dB
ON
OFF
MANUAL ON + ON
-30
dB Dippschalter
SUM A AND B
Gruppe 1 und 2
-6 dB -6 dB -2 dB CTRL OFF + OFF
Buchse für
Netzkabel MAINS INPUT 230 V~
50 / 60 Hz 330 W
12 V
REMOTE
DIGITAL IN
AES/EBU
DIGITAL THRU
AES/EBU
ANALOG
IN
292-8260T-6
SERIAL NUMBER
12 Volt MAGNETICALLY SHIELDED
MADE IN FINLAND www.genelec.com
Abbildung 2: Anschlüsse und Schalter auf der Rückseite eines 8260A. 8240A und 8250A und 8351A nutzen das gleiche
Layout - jedoch ohne den 12 V-Trigger-Anschluss
wird ein Kabel pro Kanal benötigt und es ist keine Kanalaus-
Verwendung der Monitore im wahl erforderlich. Der Dual-Wire Modus wird automatisch von
Standalone-Modus der Eingangsstufe erkannt.
Wenn die Monitore nicht mit dem Genelec Netzwerk verbun- Wenn das digitale Quellgerät einen Lautstärkeregler hat, der
den sind, arbeiten sie im Standalone-Modus. Alle Einstellun- auf der digitalen Ebene regelt, kann es vorteilhaft sein, den
gen, die mit der GLM Software gemacht wurden, können aber Pegel auf der Rückseite des Monitors abzusenken. Dadurch
in den Lautsprechern gespeichert werden. Diese Settings erhalten Sie eine höher Bitauflösung des Digitalsignals.
werden über den Dip-Schalter 1 der zweiten Schaltergruppe
mit der Schaltung auf “STORED” (ON) aktiviert. Diese Einstel- Bei Verwendung der Digitaleingänge referenzieren alle Audi-
lung muss bei jedem Lautsprecher vorgenommen werden. oausgänge auf 0 dBFS (Digital Full Scale, der größtmögliche
Pegel im AES/EBU-Signal). Die Monitore produzieren 100 dB
Alle weiteren Informationen zur Nutzung der GLM Software SPL bei 1 Meter im freien Raum für ein digitales Eingangssig-
finden Sie in der Bedienungsanleitung der Software. nal von -30 dB FS.
13
h Akustische
Achse
Max
60 cm Zu ve
m > 60 c rmeiden
Min 5 c m
Abbildung 5: Empfohlene Abstände zwischen Vorderseite Abbildung 6: Empfohlene Aufstellung für 5.1 Mehrkanal-
des Lautsprechers und einer Rückwand: geeignet (grün) Wiedergabe
und ungeeignet (rot)
“12 V REMOTE” Anschluss (nur 8260A) Wird die LED rot, reduzieren Sie den Pegel der analogen Quel-
Hier können Sie die 8260A mit einer 12V Spannung ein- und le. Wenn ein digitales Signal verwendet wird, stellen Sie sicher,
ausschalten. Der erforderliche Mindeststrom beträgt 70 mA. dass keine Bitfehler im AES/EBU-Datenstrom vorhanden sind.
14
in Richtung der Hörposition (siehe Abbildung 3) ausgerichtet Monitors liegt, desto weiter sollte er von der Rückwand ent-
ist. Es wird eine vertikale Anordnung empfohlen, da sie akusti- fernt aufgestellt werden, um dieses Phänomen zu umgehen.
sche Auslöschungsprobleme bei der Übergangsfrequenz mi- Alternativ empfiehlt sich eine wandnahe Aufstellung und
nimiert. Der 8351A kann ohne Einschränkung auch horizontal Kompensation der resultierenden Bass-Anhebung über die
betrieben werden. Dip-Schalter bzw. die GLM Software.
Achten Sie auf Symmetrie Die Entfernungen zur Decke und anderen Wänden können
Stellen Sie sicher, dass die Monitore symmetrisch und mit geringer sein als der Abstand zur Rückwand. Reflexionen die-
gleichem Abstand zur Hörpositionen aufgestellt sind. Platzie- ser Oberflächen können sich ebenfalls auswirken und sollten
ren Sie die Monitore falls möglich so, dass die Hörposition auch berücksichtigt werden.
auf der Mittelachse des Raumes liegt und die Monitore den
gleichen Abstand von dieser Mittelachse haben (siehe Abbil- Betriebsumgebung
dung 4). Die Lautsprecher sind ausschließlich zur Nutzung in geschlos-
senen Räumen konzipiert. Die zulässige Umgebungstempera-
Minimieren Sie Reflexionen tur liegt zwischen 15 und 35 Grad Celsius mit einer relativen
Akustische Reflexionen von Objekten wie Tischen, Schrän- Luftfeuchtigkeit von 20-80 Prozent. Das Vorhandensein von
ken, Computerbildschirmen etc., die nahe an den Lautspre- Kondenswasser muss während des Betriebs auf jeden Fall
chern stehen, können unerwünschte Verfärbungen und ein vermieden werden. Wenn die Lautsprecher in einer kalten Um-
unscharfes Stereobild verursachen. Dies kann verhindert gebung gelagert oder transportiert wurden und anschließend
werden, indem die Lautsprecher entfernt von reflektierenden in einen warmen Raum gebracht werden, müssen sie sich voll-
Oberflächen aufgestellt werden. Beispielsweise führt die Auf- ständig an die neue Umgebungstemperatur angepasst haben,
stellung auf Stativen über und hinter einem Mischpult häufig bevor sie mit dem Stromnetz verbunden werden können.
zu besseren Ergebnissen als die Platzierung auf der Meter
Bridge. Eine symmetrische Positionierung der reflektierenden Werden die Lautsprecher in begrenzten Platzverhältnissen wie
Objekte ist ebenfalls wichtig, um ein stabiles Stereobild zu er- einem Schrank oder in der Wand installiert, muss die Kühlung
reichen (siehe Abbildung 4). des Verstärkers und die Funktionalität des Bass-Reflex-Ka-
nals sichergestellt werden. Die Umgebung des Lautsprechers
Tieffrequente Auslöschungen muss immer zum Abhörraum geöffnet sein. Der Mindestab-
Grundsätzlich kann eine Reflexion über die Wand hinter dem stand beträgt 5 cm zu allen Seiten. Der angrenzende Bereich
Lautsprecher zu einer Auslöschung der tiefen Frequenzen muss belüftet werden oder ausreichend groß sein, damit die
und damit Reduzierung des Bass-Pegels führen. Dies tritt auf, Wärme abgeleitet werden kann und die Temperatur nicht über
sobald die Vorderseite des Monitors mehr als 30 cm von der 35 Grad Celsius steigt.
Rückwand entfernt ist. Wandabstände zwischen 1 m und 2,2
m sollten vermieden werden (siehe Abbildung 5). Montagemöglichkeiten
Der Iso-Pod™-Ständer entkoppelt den Monitor vom Unter-
Als Faustregel gilt: Je tiefer die untere Grenzfrequenz eines grund und ermöglicht die Neigung zur korrekten Ausrichtung
15
Freifeld - - - -
Freie Aufstellung in - -2 dB - -
einem gedämmten
Raum
Nahfeld-Aufstellung - -2 dB - -4 dB
auf einer reflektier- STORED/MANUAL CONTROL auf STORED (ON) steht oder
enden Oberfläche
wenn der Monitor an das GLM Netzwerk angeschlossen ist.
In einer Ecke - -4 dB -4 dB -
Tabelle 2: Empfohlene Einstellung der Klangregelung für typis- Die Nutzung eines akustischen Mess-Systems wird empfoh-
che Platzierungen der Monitore len, um das Resultat der Einstellungen analysieren zu können.
Falls kein System zur Verfügung steht, kann auch aufmerksa-
der akustischen Achse. Der Ständer kann an drei Punkten an- mes Hören mit passenden Aufnahmen zu guten Ergebnissen
gebracht werden, die vertikale und symmetrisch horizontale führen. Beginnen Sie die Anpassung damit, dass alle Schalter
Positionierung ermöglichen. auf OFF stehen. Messen bzw. bewerten Sie dann systema-
tisch die verschiedenen Einstellungs-Kombinationen, um den
8240A, 8250A, 8351A und 8260A haben auf der Rückseite besten Frequenzgang zu bestimmen. Tabelle 2 zeigt Ihnen ei-
zwei Paare von M6x10 mm Bohrungen und können mit Kö- nige typische Settings.
nig&Meyer Halterungen montiert werden. Auf der Unterseite
der 8240A und 8250A gibt es eine M10x10 mm Bohrung, die
dazu genutzt werden kann, den Monitor auf der Stellfläche zu Bass Roll-Off Regelung
sichern. Benutzen Sie diese Bohrung nicht zur Montage auf Die Bass Roll-Off Regelung (Schalter 1 und 2) senken den Be-
einem Mikrofonständer mit 3/8“ Gewinde. Über Ihren Genelec reich nahe der unteren Grenzfrequenz ab. Es kann eine Ab-
Händler haben Sie Zugriff auf eine große Auswahl an Wand- senkung von -2 dB (Schalter 1 ON), -4 dB (Schalter 2 ON) oder
und Deckenhalterungen. -6 dB (Schalter 1 und 2 ON) ausgewählt werden.
16
17
Sicherheitshinweise
• 8240A, 8250A, 8351A und 8260A sind entsprechend
internationaler Sicherheitsstandards entwickelt worden. Für
den sicheren Betrieb und eine lange Lebensdauer müssen
die folgenden Warnhinweise und Sicherheitsvorkehrungen
beachtet werden:
•
• Wartung und Einstellung sollte ein zertifizierter Genelec-
Servicetechniker durchführen. Das Gehäuse darf nicht
geöffnet werden. Nutzen Sie das Gerät nicht mit einem
ungeerdeten Netzkabel oder einem Anschluss ohne
Schutzleiterkontakt, da dies zur Gefährdung von Personen
führen kann.
• Um Feuer und Stromschlägen vorzubeugen, vermeiden Sie
es, das Gerät Regen oder Feuchtigkeit auszusetzen.
• Stellen Sie keine mit Flüssigkeit gefüllten Gegenstände wie
Vasen auf oder neben den Lautsprecher.
• Beachten Sie, dass der Verstärker erst vollständig vom
Netz getrennt ist, wenn das Netzkabel vom Netzanschluss
abgezogen wurde.
• Zur ausreichenden Kühlung ist eine ungehinderte
Luftzirkulation hinter dem Lautsprecher erforderlich.
• Behindern Sie nicht die Luftzirkulation rund um den
Lautsprecher.
WARNUNG!
Diese Lautsprecher können Lautstärkepegel von mehr als 85
dB/SPL erzeugen, was zu irreparablen Hörschäden führen
kann.
18
A 90
85 d 0° 15° 30°
B
DESKTOP LF 85
90 80 r
85 A 80
45°
80 90 75
BASS TILT 60°
85 70
80 65
BASS ROLL-OFF TREBLE TILT
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Abbildung 10: Die Kurven zeigen den Effekt der Schalter Abbildung 11: Die obere Kurve zeigt die horizontale Rich-
“Bass Tilt”, “Treble Tilt”, “Desktop Low Frequency” und “Bass twirkung eines 8240A, gemessen in 1 m Abstand. Die untere
Roll-Off” auf den Frequenzgang eines 8240A im Freifeld Kurve zeigt den Leistungsfrequenzgang des Systems
Genelec Oy 8250A (dBr) vs freq (Hz) 17 Jan 06 Genelec Oy 8250A (dBr) vs freq (Hz) 17 Jan 06
100
d
B
r 90 95
A 90
85 d
0° 15° 30°
B
90 80 DESKTOP LF r 85
85 A 80
80 90 75
BASS TILT 45° 60°
85 70
80 65
BASS ROLL-OFF TREBLE TILT
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Abbildung 12: Die Kurven zeigen den Effekt der Schalter Abbildung 13: Die obere Kurve zeigt die horizontale Rich-
“Bass Tilt”, “Treble Tilt”, “Desktop Low Frequency” und “Bass twirkung eines 8250A, gemessen in 1 m Abstand. Die untere
Roll-Off” auf den Frequenzgang eines 8250A im Freifeld Kurve zeigt den Leistungsfrequenzgang des Systems
Genelec Oy 8351A dBr) vs freq (Hz) 20 Nov 2014 Genelec Oy 8351A (dBr) vs freq (Hz) 20 Nov 2014
d 100
B
r 90 95
A
85 90
d
0° 15° 30°
B
90 80 DESKTOP LF r 85
85 A 80
80 90 75
BASS TILT 45° 60°
85 70
80 65
BASS ROLL-OFF TREBLE TILT
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Abbildung 14: Die Kurven zeigen den Effekt der Schalter Abbildung 15: Die obere Kurve zeigt die horizontale Rich-
“Bass Tilt”, “Treble Tilt”, “Desktop Low Frequency” und “Bass twirkung eines 8351A, gemessen in 1 m Abstand. Die untere
Roll-Off” auf den Frequenzgang eines 8351A im Freifeld Kurve zeigt den Leistungsfrequenzgang des Systems
19
A 90
85 d
0° 15° 30°
B
DESKTOP LF 85
90 80 r
85 A 80
80 90 75
BASS TILT 45° 60°
85 70
80 65
TREBLE TILT
BASS ROLL-OFF
60
55
50
20 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k
Hz Hz
Abbildung 16: Die Kurven zeigen den Effekt der Schalter Abbildung 17: Die obere Kurve zeigt die horizontale Rich-
“Bass Tilt”, “Treble Tilt”, “Desktop Low Frequency” und “Bass twirkung eines 8260A, gemessen in 1 m Abstand. Die untere
Roll-Off” auf den Frequenzgang eines 8260A im Freifeld Kurve zeigt den Leistungsfrequenzgang des Systems
Abbildung 18: Darstellung der horizontalen Richtwirkung Abbildung 19: Darstellung der vertikalen Richtwirkung
eines 8240A eines 8240A
Abbildung 20: Darstellung der horizontalen Richtwirkung Abbildung 21: Darstellung der vertikalen Richtwirkung
eines 8250A eines 8250A
20
Abbildung 24: Darstellung der horizontalen Richtwir- Abbildung 25: Darstellung der vertikalen Richtwirkung
kung eines 8260A eines 8260A
90
d
B
r 85
A 80
75
20 50 100 200 500 1k 2k 5k 10k 20k 40k
Hz
21
Maximaler Spitzen-Schalldruck pro Paar auf ≥ 115 dB SPL ≥ 120 dB SPL ≥ 121 dB SPL ≥ 123 dB SPL
einem Mischpult in 1 m Abstand mit Musik-
Material
Maximaler Kurzzeit-Sinus-Schalldruck in 1 m (from 100 Hz to 3 kHz) (from 100 Hz to 3 kHz) (from 100 Hz to 3 kHz) (from 100 Hz to 3 kHz)
Entfernung auf Achse im Halbraum, gemittelt ≥ 105 dB SPL ≥ 110 dB SPL ≥ 111 dB SPL ≥ 113 dB SPL
wie angegeben
Übergangsfrequenz 3 kHz 1.8 kHz 470 Hz, 2.6 kHz 490 Hz, 2.6 kHz
Eingangssignal
Analog 1 XLR female (10 kOhm input load impedance)
AES/EBU (single wire und dual wire) 1 XLR female (conforms to IEC 60958-4)
Ausgangssignal / Thru-Signal
AES/EBU (single wire und dual wire) 1 XLR male (conforms to IEC 60958-4)
Digitales Audiosignal
Wortlänge 16 - 24 bits
Sample-rate 32 - 192 kHz
Kontroll-Netzwerk
Art proprietary GLMTM network
Verbindung 2 RJ45, CAT5 cables
Leistungsaufnahme
Ruhezustand 14 W 17 W 20 W 26 W
Voller Ausgangspegel 110 W 170 W 290 W 330 W
Abmessungen
Höhe 350 mm (1313/16 in) 433 mm (171/16 in) 433 mm (171/16 in) 570 mm (227/16 in)
Breite 237 mm (93/8 in) 286 mm (111/4 in) 286 mm (111/4 in) 357 mm (141/16 in)
Tiefe 223 mm (813/16 in) 278 mm (1015/16 in) 278 mm (1015/16 in) 347 mm (135/8 in)
Höhe mit IsoPod 365 mm (143/8 in) 452 mm (1713/16 in) 452 mm (1713/16 in) 593 mm (233/8 in)
Gewicht 9.4 kg (20.8 lb) 14.6 kg (32 lb) 19 kg (42 lb) 27.5 kg (60.5 lb)
* Die Notch- und Shelving-Filter-Einstellungen, AutoCalTM und manuelle Einstellungen über GLMTM sind Bestandteil der Genelec Loudspeaker Manager (GLMTM) Software.
22