Professional Documents
Culture Documents
1
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
2
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
3
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
4
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
1.3.1.1 Uvod
1.3.1.2 Podloge
Podaci o geometriji objekta su uzete iz originalnog projekta arhitekture. Originalni
projekat konstrukcije nije nađen u arhivi.
5
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
dobijaju cca 15% veći statički uticaji nego kombinacijom opterećenja od 7 KN/m² +
dinamičko opterećenje od sušne grupe sa temeljima.
Ojačanje ploče u 1. slučaju je predviđeno lepljenjem karbonskih traka Sika® CarboDur®
S512, b=50 mm, t=1.2 mm, e=80 mm, sa donje strane ploče na mestima većih pravougaonih
rupa naknadno zatvorenih betonom, kao i kod većih pravougaonih i okruglih rupa, naknadno
izbušenih u ploči.
Ojačanje ploče u 2. slučaju je predviđeno čeličnim, sa pločom spregnutim čeličnim profilima,
koji su sračunati da mogu da prime punu silu smicanja na tom delu ploče. Silu smicanja
prenose na AB gredu putrem čeone ploče i četiri ankera M16 proračunatih da na tu slu
smicanja. Ankeri za sprezanje i za prenos na AB gredu su tipa R-XPT Throughbolt, M16x220
mm, dubina ankerisanja je cca 120 mm. Predviđeno je ukupno 22 takvih ojačanja.
ODGOVORNI PROJEKTANT,
7
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
1. Pravilnici i standardi
- Zakon o planiranju i izgradnji
- Pravilnik za građevinske konstrukcije 1 - SL89-2019.
2. Opterećenja
2. AB konstrukcije
8
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
3. Čelična konstrukcija
SRPS EN 1993-1-8:2005 – Eurocode 3: Design of steel structures – Par 1-8: Design of joints.
SRPS EN 1993-1-10 – Eurocode 3: Design of steel structures – Part 1-10: Material
toughness and thorugh- thickness properties.
9
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
Poz. Jedinična
broj OPIS Mera Količina x cena = Cena
I BETONSKI RADOVI
1 Betoniranje postamenata-temelja sušne grupe, na
koti +5.00 m, betonom marke MB 30 (C25/30).
Obračun po m3 zajedno sa oplatom. m3 60.0 x =
UKUPNO BETONSKI RADOVI:
II ARMIRAČKI RADOVI
1 Nabavka, transport, priprema i ugradnja šipki
armature kvaliteta B500B. Armatura mora biti čista
od korzije i prljavštine. Prilikom ugradnje
upotrebljavati distancere između oplate i armature
po propisima (od plastike i/ili cementa).
Obračun po kg upotrebljene armature. kg 983.1 x =
UKUPNO ARMIRAČKI RADOVI:
IV KARBONSKE TRAKE
1 Nabavka i montaža karbonskih traka Sika®
CarboDur® S512, b=50 mm, t=1.2 mm, e=80 mm,
lepljenjem po donjoj površini postojeće AB ploče, u
svemu po detaljima iz projekta i tehničkim
preporukama od strane proizvođača.
Obračun po m' trake. m' 976.2 x =
UKUPNO KARBONSKE TRAKE :
10
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
VRSTA RADOVA
I BETONSKI RADOVI
II ARMIRAČKI RADOVI
III ČELIČNA KONSTRUKCIJA
IV KARBONSKE TRAKE
ODGOVORNI PROJEKTANT,
11
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
12
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
2. ANALIZA OPTEREĆENJA:
2.1.1 KONSTRUKCIJA
Sopstvena težina konstrukcije - računa sam program
- liveni teraco, d = 2 cm g= 25 KN/m³ 0.50 KN/m²
- cem. košuljica dsr. 3 cm g= 21 KN/m³ 0.63 KN/m²
g= 1.13 KN/m²
2.1.2 AB POSTAMENTI
0.993
G1
1.913
G2
0.92
g2
g1
B= 0.94 1.255 1 L= 1.04
2.195
oduzimaju se rupe za olakšanje
Dimenzije postamenta: L+0.1 (m) B+0.05 H Lr Br Hr
1.24 0.99 1.913 0.4 0.3 1.913 G1 = 50.85 KN
1.14 1.31 0.6 0.4 0.3 0.6 G2 = 19.69 KN
G 1.212
1.06
g= 34.86 KN/m² 1
2.1
13
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
Q1
Q2
G 1.212
0.96
qd = 4.32 KN/m² 1
gb = 7.82 KN/m²
2
Q= 60 KN sa betonskim temeljima
Težina betona ukupno, Gb = 55.85 KN γb = 24 KN/m³
Oduzimama se rupa, LxBxH = 1.29 0.4 1.21
Vrupe = 0.63 m³
oduzima se težina betona rupe, Gbr = 15.0094 KN
Težina betona bez rupe, Gbn = 40.84 KN
Bez betona: Q= 4.15 KN x kd = 8.3 KN
14
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
Setovi ploča
No d[m] e[m] Materijal Tip proračuna E2[kN/m2]
α Ortotropija G[kN/m2]
<1> 0.280 0.140 1 Tanka ploča 0.000e+0
90.00 Anizotropna 0.000e+0
<2> 0.280 0.140 1 Tanka ploča
Izotropna
15
GRUPE
B
m
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
m m m m m m m 8m
28
m 28
28 28 28 28 28 0. 0.2
0.
28 28 .28
0. 0. 0. 0. 0 0. 0. = d=
= = = 0. = = = = d >
d=
<2
2.64 0.80
2.44 1.00
2.14 1.30 m
2.09 1.10
1.81 1.10
C
5.81 1.30 2.14 1.30 3.44 1.30 1.46 1.30 8.76 1.30
0.24
1.30 6.17 1.30 5.58 1.30 8.93 1.101.301.00 2.00 1.30 1.38
24.
23.
22.
21.
20.
19.
18.
17.
16.
15.
14.
13.
12.
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
Datum:
2.4.2023.
16
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
17
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
18
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
19
My [kNm/m]
-4.46
0.00
17.92
35.85
53.77
71.69
89.62
107.54
GRUPE
-2.52
-2.52 -4.35 -4.32 -4.32 -4.32 -4.33 -4.33 -4.32 -4.32 -4.32 -4.42 -4.45 -4.39 -4.45 -3.69
B
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
101.69 101.33 101.11 101.27 101.05 101.13 101.23 101.34 101.33 104.65 107.54 103.95 107.22 97.67
4.50
-2.52
-2.52 -3.65 -3.63 -3.63 -3.63 -3.63 -3.63 -3.63 -3.63 -3.63 -3.89 -3.88 -3.19
C
24.
23.
22.
21.
20.
19.
18.
17.
16.
15.
14.
13.
12.
Opt. 7: 1.35xI+1.35xII+1.35xIII+1.5xIV+1.5xV
63.67
84.89
Statički proračun
106.11
127.33
-5.85
-5.83 -5.84 -5.84 -5.84 -5.83
-5.85
B
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
Opt. 8: 1.35xI+1.35xII+1.5xVI
4.50
-5.85
-5.83 -5.84 -5.84 -5.84 -5.83
-5.85
C
24.
23.
22.
21.
20.
19.
18.
17.
16.
15.
14.
13.
12.
2.4.2023.
20
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
Opt. 7: 1.35xI+1.35xII+1.35xIII+1.5xIV+1.5xV
My [kNm/m]
4.50
-27.13
0.00
50.72
101.43
152.15
202.87
253.58
304.30
-3.15
-3.76
-1.36
-3.84
12.
-1.78
-4.39
-4.69
-3.83
5.00
-5.14
-2.74
-2.93 -2.75
-3.38
-5.80
259.92
13.
-7.82
-1.55
-5.50
-3.60
5.00
-2.85
14.
-3.47
-3.06
5.00
-3.44
-3.08
-3.50
15.
-1.68
-1.65
-2.82
-2.82
5.00
-4.75
-3.45
16.
-3.47
-4.75
5.00
-2.99
-2.93
-1.64
-1.65
-3.54
-3.09
17.
-3.26
5.00
-3.73
-4.72
-9.22291.95
-24.26-1.91
-27.12-2.35
18.
-1.28
-5.97
-6.74
5.00
-2.21
-2.62
257.90
304.30
-5.01
-3.88
19.
-3.30
-2.76
5.00
20.
-3.73
-4.44
-2.31
-4.74
5.00
-1.91 -0.97
-1.66 -3.50
-4.04
-5.21
21.
-2.82
-2.73
-4.66
-3.05-3.49
5.00
-3.55
-1.70
-1.64
-2.88
-2.69
22.
-4.81
-3.86
5.00
-1.18
-0.95
-1.86
-1.79
-4.34
-3.52
23.
5.00
-1.99
-2.04
-1.99
-2.05
24.
Kao što se može videti, postoje veliki skokovi u vrednostima momenata savijanja na
ivicama otvora u ploči i samim tim koncentracije napona u betonu, što se moglo i očekivati. U
svakom slučaju one su dosta veće usled opterećenja sa kojim je sračunata armatura u
originalnom proračunu iz 1964. godine, nego usled opterećenja sušnom grupom sa
postamentima.
21
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
Dimenzionisanje (beton)
Usvojena armatura Aa - d.zona [cm²/m]
0.00
EC 2 (EN 1992-1-1:2004), C30/37, S500N, a=2.00 cm 7.19
14.37
Ø14/10(α=90°)
4.50
Ø8/20(α=180°)
Aa - d.zona
22
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
4.59
0.71 3.87
1.16 1.52
2.50
9.
5.00
5.00
3.33
1.37
0.37
10.
1.31
0.28
2.20
1.27
5.00
5.00
0.20 0.78 0.20 0.75 0.20 0.67 0.20
2.33
11.
2.20
1.59
0.87
3.41
0.20 0.68 0.200.35 0.47
0.56
1.82
5.00
1.23
2.20
0.30
2
0.20
0.79
0.41 0.56
0.29
1.59
DILATACIJA U PLOČI
0.80
0.39
12.
1.04 1.83
D
23
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
Izometrija
Tabela materijala
No Naziv materijala E[kN/m2] μ γ[kN/m3]
Em[kN/m2] μm αt[1/C]
1 Beton MB 20 2.850e+7 0.20 25.00
2.850e+7 0.20 1.000e-5
Setovi ploča
No d[m] e[m] Materijal Tip proračuna E2[kN/m2]
α Ortotropija G[kN/m2]
<1> 0.280 0.140 1 Tanka ploča 0.000e+0
90.00 Anizotropna 0.000e+0
24
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
25
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
26
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
27
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
28
Datum:
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE 2.4.2023.
GRUPE
29
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
Statički proračun
Opt. 7: 1.35xI+1.35xII+1.35xIII+1.5xIV+1.5xV Tz,y [kN/m]
-2191.85
-1753.48
-1315.11
-876.74
-438.37
0.00
313.13
626.27
-2159.50
-2191.84 605.41
-1895.20 462.76
472.66
591.99
626.27 514.56
375.68
-236.93
-234.18
-207.74
-209.19
-209.75
-203.18
-193.85
-186.81
-180.59
-166.35
-164.80
-158.02
-160.41
-149.40
-142.10
-144.13
-138.35
-126.47
-125.47
-124.87
-122.95
-119.10
-110.84
-70.98
Uticaji u ploči: max Tz,y= 626.27 / min Tz,y= -2191.84 kN/m
Opt. 8: 1.35xI+1.35xII+1.5xVI Tz,y [kN/m]
-3187.48
-2549.98
-1912.49
-1274.99
-637.50
0.00
507.55
1015.10
543.58
779.05 693.89 684.78 689.82 688.44 692.23 700.58
-3187.47
-3137.98 1015.10
-3051.17 977.48
994.82
899.96
895.37 814.42
642.09 611.07
616.31
-518.96
-462.18
-449.19
-348.28
-303.68
-301.10
-289.35
-288.30
-274.58
-274.50
-265.69
-259.82
-261.11
-243.84
-243.39
-246.61
-250.36
-238.71
-240.25
-235.18
-226.37
-227.97
-219.11
-159.55
30
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
-100.92
128.65
50.66
93.47 77.06 80.53 93.69 51.27
-92.26 -83.18
19.96
-147.11 -131.84
-147.10
91.8591.02
31
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
Opt. 7: 1.35xI+1.35xII+1.35xIII+1.5xIV+1.5xV
115.55
Uticaji u lin. osloncu: max r2= 4903.17 / min r2= -2847.67 kN/m
Opt. 8: 1.35xI+1.35xII+1.5xVI
214.86
Uticaji u lin. osloncu: max r2= 8419.04 / min r2= -4763.82 kN/m
32
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
(MB 15) (MB 20) (MB 25) (MB 30) (MB 40) (MB 45) (MB 50) (MB 55) (MB 60)
C12/15 C16/20 C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60
fck 12 16 20 25 30 35 40 45 50
fc,cub 15 20 25 30 37 45 50 55 60
τRd 0.18 0.22 0.26 0.3 0.34 0.37 0.41 0.44 0.48
VRd1 = 45.00 KN
VRd1/bw = 145.17 KN/m' < Vsd = 224 KN/m Presek NE zadovoljava na smicanje!
(MB 15) (MB 20) (MB 25) (MB 30) (MB 40) (MB 45) (MB 50) (MB 55) (MB 60)
C12/15 C16/20 C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60
fck 12 16 20 25 30 35 40 45 50
fc,cub 15 20 25 30 37 45 50 55 60
τRd 0.18 0.22 0.26 0.3 0.34 0.37 0.41 0.44 0.48
33
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
(MB 15) (MB 20) (MB 25) (MB 30) (MB 40) (MB 45) (MB 50) (MB 55) (MB 60)
C12/15 C16/20 C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60
fck 12 16 20 25 30 35 40 45 50
fc,cub 15 20 25 30 37 45 50 55 60
τRd 0.18 0.22 0.26 0.3 0.34 0.37 0.41 0.44 0.48
(MB 15) (MB 20) (MB 25) (MB 30) (MB 40) (MB 45) (MB 50) (MB 55) (MB 60)
C12/15 C16/20 C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60
fck 12 16 20 25 30 35 40 45 50
fc,cub 15 20 25 30 37 45 50 55 60
τRd 0.18 0.22 0.26 0.3 0.34 0.37 0.41 0.44 0.48
34
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
(MB 15) (MB 20) (MB 25) (MB 30) (MB 40) (MB 45) (MB 50) (MB 55) (MB 60)
C12/15 C16/20 C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60
fck 12 16 20 25 30 35 40 45 50
fc,cub 15 20 25 30 37 45 50 55 60
τRd 0.18 0.22 0.26 0.3 0.34 0.37 0.41 0.44 0.48
(MB 15) (MB 20) (MB 25) (MB 30) (MB 40) (MB 45) (MB 50) (MB 55) (MB 60)
C12/15 C16/20 C20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60
fck 12 16 20 25 30 35 40 45 50
fc,cub 15 20 25 30 37 45 50 55 60
τRd 0.18 0.22 0.26 0.3 0.34 0.37 0.41 0.44 0.48
35
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
36
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
be = 31 aa = Ab*a/Ai/n
ab = Aa*a/Ai
Ab db/2
db = 28 Tb yb,g = ab+db/2 = 20.578
ab=Aa*a/Ai= 6.58
ya,g = -7.422 a = 21.5 cm yb,d = -7.422
Ti aa = Ab*a/Ai*n = 14.92 xi
ha = 15
Ta
ya,d = 22.422 ha/2
Aa
20
37
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
38
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
e=0
max V = 45.50 KN
Z = -P = 0 KN
T= 45.50 KN
ODGOVORNI PROJEKTANT,
39
STATIČKA PROVERA AB PLOČE NA KOTI +5,00 m U STAROJ HALI Datum:
KARTON MAŠINE NA OPTEREĆENJE OD NOVE OPREME SUŠNE
GRUPE 2.4.2023.
40
SIKA® CARBODUR® CALCULATION SOFTWARE
PROJECT: OJAČANJE AB PLOČE NA MESTU PRAVOUG. OTVORA U X
PRAVCU
ELEMENT:
INDEX
1. DESIGN CRITERIA AND REGULATIONS................................................................................................................................ 3
2. CALCULATION ASSUMPTIONS............................................................................................................................................ 3
2.1. Geometry............................................................................................................................................................. 3
2.2. Concrete............................................................................................................................................................... 3
2.3. Reinforcing steel................................................................................................................................................... 4
2.4. Strength reduction factors.................................................................................................................................... 4
2.5. Load factors.......................................................................................................................................................... 4
2.6. Requirements for restriction of crack width.......................................................................................................... 4
3. FRP STRENGTH................................................................................................................................................................... 4
3.1. Main FRP reinforcement....................................................................................................................................... 4
4. ANTICIPATED COMBINATIONS OF LOADS.......................................................................................................................... 5
4.1. Initial loads........................................................................................................................................................... 5
4.2. Expected loads (strenghtening design)................................................................................................................. 5
5. RESULTS............................................................................................................................................................................. 5
5.1. Summary of results............................................................................................................................................... 5
5.2. Ultimate limit states............................................................................................................................................. 5
5.3. Serviceability limit states...................................................................................................................................... 9
5.4. FRP arrangement.................................................................................................................................................. 11
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
1/15
6. PRODUCT SPECIFICATION.................................................................................................................................................. 12
6.1. Bonded Sika CarboDur® plates.............................................................................................................................. 12
6.1.1. Concrete surface preparation......................................................................................................................... 12
6.1.2. Sika CarboDur® plates..................................................................................................................................... 13
6.1.3. Epoxy Adhesive............................................................................................................................................... 13
6.1.4. Application procedure..................................................................................................................................... 14
7. LEGAL DISCLAIMER............................................................................................................................................................ 15
8. ABOUT SIKA® CARBODUR® CALCULATION SOFTWARE....................................................................................................... 15
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
2/15
1. DESIGN CRITERIA AND REGULATIONS
Flexural strengthening of beam. The calculation comprises the evaluation of the most unfavorable section as defined by the
user, based on:
‐ Sia 260: 2013 Basics of planning structural design projects
‐ Sia 262: 2013 Concrete structures
‐ SIA 166: 2004 Externally bonded reinforcement
‐ Near surface mounted (NSM) calculations are based on:
‐ Concrete Society Technical Report No. 55 (TR 55): design guidance for strengthening concrete structures using fibre
composite materials, Third Edition 2012.
‐ The design of post‐tensioned CFRP plates is based on the Sika® CarboStress® system.
‐ Country: Serbia
2. CALCULATION ASSUMPTIONS
2.1. Geometry
Cross section = Slab
Height = 280 mm
280
2.2. Concrete
Compressive strength of concrete
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
3/15
Concrete strength (fck) = 20 MPa
Cylinder specimen = 20 MPa
Cube specimen = 25 MPa
2.3. Reinforcing steel
Reinforcement layers
Steel fsk Es Diameter C. to c. spacing
Bottom layer d1 mm
(MPa) (MPa) (mm) (mm)
1. 12 (B240) 240 200000 12.00 200
2.4. Strength reduction factors
Defined by (SIA)
Concrete
c = 1.50
t = 1.00
fc = 1.00
1
30 3
fc 1
fck
Steel
s = 1.15
2.5. Load factors
SIA combinations Permanent loads Imposed loads
Anticipated loads 1.35 1.50
FRP Reinforcement failure 1.00 0.30
Fire situation 1.00 0.30
SLS, frequent 1.00 0.50
SLS, quasi‐permanent 1.00 0.30
Category A: domestic, residential areas
1 = 0.5
2 = 0.3
2.6. Requirements for restriction of crack width
Requirements for restriction of crack width in accordance with SIA 262
Normal
3. FRP STRENGTH
3.1. Main FRP reinforcement
Simply bonded. Sika CarboDur® S
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
4/15
C. to c. spacing El tl Width
Sika® CarboDur® S212 lu
(mm) (MPa) (mm) (mm)
Layer: 1 50 165000.00 1.200 0.0176 20.00
4. ANTICIPATED COMBINATIONS OF LOADS
4.1. Initial loads
(Positive) Mi : 21.15 kN∙m/m
4.2. Expected loads (strenghtening design)
Permanent loads (Positive) MG : 19.23 kN∙m/m
Imposed loads (Positive) MQ : 17.86 kN∙m/m
5. RESULTS
5.1. Summary of results
ULS Anticipated loads
loading Md (kN∙m/m) MRd (kN∙m/m) MRd Md (Nd = NRd)
Strengthened section
Su = 1.35 ∙ SG + 1.50 ∙ SQ 52.75 172.18
172.18 kN∙m/m 52.75 kN∙m/m
ULS Reinforcement failure
loading Md (kN∙m/m) MRd (kN∙m/m) MRd Md (Nd = NRd)
Un‐strengthened section
Su = 1.00 ∙ SG + 0.30 ∙ SQ 24.59 35.59
35.59 kN∙m/m 24.59 kN∙m/m
Serviceability limit states
loading Service stresses
s 0.9∙fsk
Su = 1.00 ∙ SG + 0.50 ∙ SQ
177.09 MPa 216.00 MPa
Serviceability limit states
loading Service stresses
c 0.45∙fck
Su = 1.00 ∙ SG + 0.30 ∙ SQ
3.71 MPa 9.00 MPa
5.2. Ultimate limit states
When analysing a cross‐section to determine its ultimate moment of resistance, the following assumptions should be made:
The strain distribution in the concrete in compression and the strains in the reinforcement, whether in tension or
compression, are derived from the assumption that plane sections remain plane and that no longitudinal slip occurs
between or within the components of the section.
The stresses in the concrete in compression are derived from the stress–strain curve in Section 3.1.7 of EN 1992‐1‐1.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
5/15
n
fcd
c2 cu2 Number
(MPa)
13.3 0.0020 0.0030 2
The tensile strength of the concrete is ignored.
The stresses in the steel reinforcement are derived from the stress–strain curves in Section 3.2 of EN 1992‐1‐1.
The strains in the cross‐section should take into account the strains present in the existing structure at the time of
application of the FRP reinforcement.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
6/15
The stresses in the FRP reinforcement are derived from the assumption that the FRP has a linear elastic characteristic
until rupture.
Restriction for FRP strain (SIA 166:2004). FRP main reinforcement
ld l min L lu , ld,max
L
ld : 0.0072
ld,max : 0.0080
l : 0.9000
Force balance of section. Initial loads
Mi = 21.15 kN∙m/m
Force balance of section. Initial loads
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.22 ‰
min = ‐0.80 ‰
Maximum stress in concrete fc = 2.77 MPa
Distance from extreme compression fiber to neutral axis x = 60.46 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 12 ‐128 ‐151.02 ‐0.76
FRP Reinforcement failure. Minimum combination of loads to be resisted by the un‐strengthened member.
Su = 1.00 ∙ SG + 0.30 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
7/15
MRd Md 35.59 kN∙m/m 24.59 kN∙m/m
Nominal moment MRd : 35.59 kN∙m/m
εmax σmax
ε = 3.0 ‰
ε = 2.0 ‰
ε = 0.0 ‰
x
εmin
Maximum and minimum strain max = 1.28 ‰
min = ‐20.85 ‰
Maximum stress in concrete fc = 14.50 MPa
Distance from extreme compression fiber to neutral axis x = 16.18 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 12 ‐128 ‐240.00 ‐19.90
Strengthened section and expected loads.
Su = 1.35 ∙ SG + 1.50 ∙ SQ
MRd Md 172.18 kN∙m/m 52.75 kN∙m/m
Nominal moment MRd : 172.18 kN∙m/m
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
8/15
εmax σmax
ε = 3.0 ‰
ε = 2.0 ‰
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 2.60 ‰
min = ‐7.94 ‰
Maximum stress in concrete fc = 13.33 MPa
Distance from extreme compression fiber to neutral axis x = 69.11 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 12 ‐128 ‐208.70 ‐7.49
FRP ‐141 ‐1182.06 ‐7.16
5.3. Serviceability limit states
For serviceability limit states, stress in steel reinforcement of concrete shall satisfy the SIA‐262 requirements, or not exceeds
0.9∙fyk
Force balance of section. SLS Frequent combination of loads
Su = 1.00 ∙ SG + 0.50 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
9/15
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.22 ‰
min = ‐0.93 ‰
Maximum stress in concrete fc = 4.14 MPa
Distance from extreme compression fiber to neutral axis x = 53.11 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 12 ‐128 ‐177.09 ‐0.89
FRP ‐141 ‐24.67 ‐0.15
Force balance of section. SLS Quasi‐permanent combination of loads
Su = 1.00 ∙ SG + 0.30 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
10/15
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.20 ‰
min = ‐0.86 ‰
Maximum stress in concrete fc = 3.71 MPa
Distance from extreme compression fiber to neutral axis x = 51.83 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 12 ‐128 ‐162.74 ‐0.81
FRP ‐141 ‐12.09 ‐0.07
5.4. FRP arrangement
The previous results correspond to the following FRP scheme:
FRP main reinforcement: Sika® CarboDur® S212. C. to c. spacing: 50 mm
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
11/15
280
6. PRODUCT SPECIFICATION
6.1. Bonded Sika CarboDur® plates
The strengthening shall be achieved using pultruded Carbodur plates reinforced polymer laminate, externally bonded to the
structure with epoxy adhesive Sikadur®‐30.
The material shall be a pultruded, unidirectional CFRP plate, and exhibit a fibre volume content >68%.
The plates shall be straight, flat and free of torsion.
The material shall have a long track record (> 25 years) for structural strengthening.
Test reports regarding reaction of adhesive joint to artificial weathering after 100 days shall be provided.
6.1.1. Concrete surface preparation
Any unsound material shall be removed and removed concrete shall be repaired as described above. Large blowholes and
honeycombing shall be filled with a suitable repair mortar.
Repair materials shall be fully compatible with the adhesive.
The actual strength of the concrete substrate shall be verified with at least three pull‐off tests.
The concrete shall be older than 28 days.
The laitance layer on the substrate surface shall be removed and an open‐textured surface shall be created.
The substrate surface shall be cleaned so that it is free from oil, grease and any other contaminants as well as loose particles
and dust.
The substrate moisture content shall be less than 4% pbw.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
12/15
6.1.2. Sika CarboDur® plates
The materials shall comply with the performance characteristics described as follows:
6.1.2.1. Typical Properties of Sika CarboDur® S plates:
Fibre volume content > 68%
Glass transition temp. > 100°C
E‐Modulus EN 2561/ASTM D3039 170000 N/mm² (MPa)
Tensile Strength EN 2561/ASTM D3039 3100 N/mm² (MPa)
Strain at break EN 2561/ASTM D3039 > 1.7%
6.1.3. Epoxy Adhesive
The material shall be epoxy based, and combine primer, putty and adhesive in one product.
The material shall not release substances dangerous to health, hygiene and the environment.
The material shall be long‐term creep resistant proven by independent report.
The material shall meet the requirements of EN 1504‐4 as structural bonding product for bonded plate reinforcement.
6.1.3.1. Typical Properties of Sikadur®‐30 adhesive:
The adhesive must comply with EN 1504‐4.
Density (parts A+B mixed) at +23°C 1.65 kg/l + 0.1 kg/l
50° 50 N/mm²
Slant shear strength at steel: 60° 60 N/mm²
70° 70 N/mm²
Bond/adhesion strength: 14 N/mm²
Shear strength: 12 N/mm²
Compressive strength: 30 N/mm²
Shrinkage / expansion: 0.1%
Workability: 85 min. at 23°C
Sensitivity to water Pass
Modulus of elasticity: 2000 N/mm²
Coefficient of thermal expansion: 100 x 10‐6
Glass transition temperature: 40°C
Durability Pass
Compliance with FIP requirement
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
13/15
Sag flow Non sag up to 3 ‐5 mm in vertical
Squeezability 4000 m2 at +15°C at 15 kg
Volume change 0.04%
Shear strength at 15°C >14 N/mm²
Shear strength at 35°C >26 N/mm²
E‐modulus in compression 9600 N/mm²
E‐modulus in tensile 11200 N/mm²
6.1.4. Application procedure
The plates shall be cut to length using either a rotary disc cutter or a hacksaw.
The plates shall be cleaned and degreased with Sika® Colma® Cleaner or an Isopropyl alcohol based cleaner.
The adhesive shall be applied to the plates in a way that it is approximately 1 mm thick on the sides and 2 mm thick in the
middle of the plate.
A very thin layer of the adhesive shall be applied to the prepared substrate surface to fill any small voids and irregularities.
The plate shall be placed on the prepared area and pressed onto the substrate, first gently by hand and second with a hard
rubber roller, until adhesive material is squeezed out on both sides of the plate. The excess material shall be removed.
In case of plate intersections, the surface of the underlying plate shall be cleaned from dirt and grease and an adhesive ramp
shall be applied on both sides of the underlying plate so the top plate is connected to the substrate on the entire area.
The freshly bonded system shall not be disturbed for at least 24 hours and any vibrations shall be kept at a minimum during
the curing period of the adhesive.
If necessary, the applied system shall be protected with a suitable coating (compatibility tests between the coating and the
laminate shall be available).
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
14/15
7. LEGAL DISCLAIMER
THIS SOFTWARE APPLICATION AND THE RESULTS DERIVED FROM ITS UTILIZATION ARE INTENDED ONLY FOR USE BY
PROFESSIONAL USERS WITH EXPERT KNOWLEDGE IN THE AREA OF THE INTENDED APPLICATION. USERS MUST
INDEPENDENTLY VERIFY THE RESULTS BEFORE ANY USE AND TAKE INTO ACCOUNT THE SITE AND APPLICATION
CONDITIONS, PRODUCT DATA SHEET AND PRODUCT LITERATURE, TECHNICAL STATE OF THE ART AS WELL AS LOCAL
APPLICABLE STANDARDS AND REGULATIONS.
With respect to the software application and results derived from its use, SIKA MAKES NO WARRANTIES OF ACCURACY,
RELIABILITY, COMPLETENESS, MERCHANTABILITY OR FITNESS FOR ANY PURPOSE. THE SOFTWARE APPLICATION IS
PROVIDED ON AN "AS‐IS" BASIS AND SIKA EXPRESSLY DISCLAIMS ANY WARRANTIES WITH RESPECT TO THE SOFTWARE
APPLICATION AND RESULTS DERIVED FROM ITS USE.
Sika shall not be liable for any consequential, punitive, incidental, exemplary, or special damages (including but not limited
to loss of business opportunity or loss of profit) arising out of the evaluation or use of the software application and results
derived from its use.
The information, and, in particular, the recommendations relating to the application and end‐use of Sika products, are given
in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied
under normal conditions in accordance with Sika's recommendations. In practice, the differences in materials, substrates
and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor
any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any
written recommendations, or from any other advice offered. The user of the product must test the product's suitability for
the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights
of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must
always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be
supplied on request.
Except as indicated otherwise, all information, text, graphic images, features, functions, and layout contained in this
software are the exclusive property of Sika and may not be copied or distributed, in whole or in part, without the Company's
express written consent.
By transmitting information to Sika, you grant to the Company the unrestricted irrevocable license to use, reproduce,
display, modify, distribute and perform such information. Personal identity information is used by Sika only to process a
request for information by you or for marketing our products and services.
© Copyright Sika Services AG 2016
8. ABOUT SIKA® CARBODUR® CALCULATION SOFTWARE
Engineered by:
Cype Software ‐ Eusebio Sempere, 5 ‐ 03003 Alicante (Spain)
www.cype.com
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
15/15
SIKA® CARBODUR® CALCULATION SOFTWARE
PROJECT: OJAČANJE AB PLOČE NA MESTU PRAVOUG. OTVORA U Y
PRAVCU
ELEMENT:
INDEX
1. DESIGN CRITERIA AND REGULATIONS................................................................................................................................ 3
2. CALCULATION ASSUMPTIONS............................................................................................................................................ 3
2.1. Geometry............................................................................................................................................................. 3
2.2. Concrete............................................................................................................................................................... 3
2.3. Reinforcing steel................................................................................................................................................... 4
2.4. Strength reduction factors.................................................................................................................................... 4
2.5. Load factors.......................................................................................................................................................... 4
2.6. Requirements for restriction of crack width.......................................................................................................... 4
3. FRP STRENGTH................................................................................................................................................................... 4
3.1. Main FRP reinforcement....................................................................................................................................... 4
4. ANTICIPATED COMBINATIONS OF LOADS.......................................................................................................................... 5
4.1. Initial loads........................................................................................................................................................... 5
4.2. Expected loads (strenghtening design)................................................................................................................. 5
5. RESULTS............................................................................................................................................................................. 5
5.1. Summary of results............................................................................................................................................... 5
5.2. Ultimate limit states............................................................................................................................................. 5
5.3. Serviceability limit states...................................................................................................................................... 9
5.4. FRP arrangement.................................................................................................................................................. 11
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
1/15
6. PRODUCT SPECIFICATION.................................................................................................................................................. 12
6.1. Bonded Sika CarboDur® plates.............................................................................................................................. 12
6.1.1. Concrete surface preparation......................................................................................................................... 12
6.1.2. Sika CarboDur® plates..................................................................................................................................... 13
6.1.3. Epoxy Adhesive............................................................................................................................................... 13
6.1.4. Application procedure..................................................................................................................................... 14
7. LEGAL DISCLAIMER............................................................................................................................................................ 15
8. ABOUT SIKA® CARBODUR® CALCULATION SOFTWARE....................................................................................................... 15
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
2/15
1. DESIGN CRITERIA AND REGULATIONS
Flexural strengthening of beam. The calculation comprises the evaluation of the most unfavorable section as defined by the
user, based on:
‐ Sia 260: 2013 Basics of planning structural design projects
‐ Sia 262: 2013 Concrete structures
‐ SIA 166: 2004 Externally bonded reinforcement
‐ Near surface mounted (NSM) calculations are based on:
‐ Concrete Society Technical Report No. 55 (TR 55): design guidance for strengthening concrete structures using fibre
composite materials, Third Edition 2012.
‐ The design of post‐tensioned CFRP plates is based on the Sika® CarboStress® system.
‐ Country: Serbia
2. CALCULATION ASSUMPTIONS
2.1. Geometry
Cross section = Slab
Height = 280 mm
280
2.2. Concrete
Compressive strength of concrete
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
3/15
Concrete strength (fck) = 20 MPa
Cylinder specimen = 20 MPa
Cube specimen = 25 MPa
2.3. Reinforcing steel
Reinforcement layers
Steel fsk Es Diameter C. to c. spacing
Bottom layer d1 mm
(MPa) (MPa) (mm) (mm)
1. 14 (B240) 240 200000 14.00 100
2.4. Strength reduction factors
Defined by (SIA)
Concrete
c = 1.50
t = 1.00
fc = 1.00
1
30 3
fc 1
fck
Steel
s = 1.15
2.5. Load factors
SIA combinations Permanent loads Imposed loads
Anticipated loads 1.35 1.50
FRP Reinforcement failure 1.00 0.80
Fire situation 1.00 0.80
SLS, frequent 1.00 0.90
SLS, quasi‐permanent 1.00 0.80
Category E: storage areas
1 = 0.9
2 = 0.8
2.6. Requirements for restriction of crack width
Requirements for restriction of crack width in accordance with SIA 262
Normal
3. FRP STRENGTH
3.1. Main FRP reinforcement
Simply bonded. Sika CarboDur® S
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
4/15
C. to c. spacing El tl Width
Sika® CarboDur® S212 lu
(mm) (MPa) (mm) (mm)
Layer: 1 80 165000.00 1.200 0.0176 20.00
4. ANTICIPATED COMBINATIONS OF LOADS
4.1. Initial loads
(Positive) Mi : 34.83 kN∙m/m
4.2. Expected loads (strenghtening design)
Permanent loads (Positive) MG : 27.84 kN∙m/m
Imposed loads (Positive) MQ : 82.00 kN∙m/m
5. RESULTS
5.1. Summary of results
ULS Anticipated loads
loading Md (kN∙m/m) MRd (kN∙m/m) MRd Md (Nd = NRd)
Strengthened section
Su = 1.35 ∙ SG + 1.50 ∙ SQ 160.58 166.71
166.71 kN∙m/m 160.58 kN∙m/m
ULS Reinforcement failure
loading Md (kN∙m/m) MRd (kN∙m/m) MRd Md (Nd = NRd)
Un‐strengthened section
Su = 1.00 ∙ SG + 0.80 ∙ SQ 93.44 93.92
93.92 kN∙m/m 93.44 kN∙m/m
Serviceability limit states
loading Service stresses
s 0.9∙fsk
Su = 1.00 ∙ SG + 0.90 ∙ SQ
240.00 MPa 216.00 MPa
Serviceability limit states
loading Service stresses
c 0.45∙fck
Su = 1.00 ∙ SG + 0.80 ∙ SQ
9.02 MPa 9.00 MPa
5.2. Ultimate limit states
When analysing a cross‐section to determine its ultimate moment of resistance, the following assumptions should be made:
The strain distribution in the concrete in compression and the strains in the reinforcement, whether in tension or
compression, are derived from the assumption that plane sections remain plane and that no longitudinal slip occurs
between or within the components of the section.
The stresses in the concrete in compression are derived from the stress–strain curve in Section 3.1.7 of EN 1992‐1‐1.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
5/15
n
fcd
c2 cu2 Number
(MPa)
13.3 0.0020 0.0030 2
The tensile strength of the concrete is ignored.
The stresses in the steel reinforcement are derived from the stress–strain curves in Section 3.2 of EN 1992‐1‐1.
The strains in the cross‐section should take into account the strains present in the existing structure at the time of
application of the FRP reinforcement.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
6/15
The stresses in the FRP reinforcement are derived from the assumption that the FRP has a linear elastic characteristic
until rupture.
Restriction for FRP strain (SIA 166:2004). FRP main reinforcement
ld l min L lu , ld,max
L
ld : 0.0072
ld,max : 0.0080
l : 0.9000
Force balance of section. Initial loads
Mi = 34.83 kN∙m/m
Force balance of section. Initial loads
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.25 ‰
min = ‐0.52 ‰
Maximum stress in concrete fc = 3.16 MPa
Distance from extreme compression fiber to neutral axis x = 91.68 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐96.24 ‐0.48
FRP Reinforcement failure. Minimum combination of loads to be resisted by the un‐strengthened member.
Su = 1.00 ∙ SG + 0.80 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
7/15
MRd Md 93.92 kN∙m/m 93.44 kN∙m/m
Nominal moment MRd : 93.92 kN∙m/m
εmax σmax
ε = 3.0 ‰
ε = 2.0 ‰
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 2.54 ‰
min = ‐21.08 ‰
Maximum stress in concrete fc = 16.67 MPa
Distance from extreme compression fiber to neutral axis x = 30.07 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐240.00 ‐19.90
Strengthened section and expected loads.
Su = 1.35 ∙ SG + 1.50 ∙ SQ
MRd Md 166.71 kN∙m/m 160.58 kN∙m/m
Nominal moment MRd : 166.71 kN∙m/m
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
8/15
εmax σmax
ε = 3.0 ‰
ε = 2.0 ‰
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 2.51 ‰
min = ‐7.66 ‰
Maximum stress in concrete fc = 13.33 MPa
Distance from extreme compression fiber to neutral axis x = 69.04 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐208.70 ‐7.16
FRP ‐141 ‐1182.06 ‐7.16
5.3. Serviceability limit states
For serviceability limit states, stress in steel reinforcement of concrete shall satisfy the SIA‐262 requirements, or not exceeds
0.9∙fyk
Force balance of section. SLS Frequent combination of loads
Su = 1.00 ∙ SG + 0.90 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
9/15
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.60 ‰
min = ‐1.56 ‰
Maximum stress in concrete fc = 10.21 MPa
Distance from extreme compression fiber to neutral axis x = 77.98 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐240.00 ‐1.45
FRP ‐141 ‐173.78 ‐1.05
Force balance of section. SLS Quasi‐permanent combination of loads
Su = 1.00 ∙ SG + 0.80 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
10/15
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.52 ‰
min = ‐1.24 ‰
Maximum stress in concrete fc = 9.02 MPa
Distance from extreme compression fiber to neutral axis x = 82.56 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐230.16 ‐1.15
FRP ‐141 ‐121.18 ‐0.73
5.4. FRP arrangement
The previous results correspond to the following FRP scheme:
FRP main reinforcement: Sika® CarboDur® S212. C. to c. spacing: 80 mm
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
11/15
280
6. PRODUCT SPECIFICATION
6.1. Bonded Sika CarboDur® plates
The strengthening shall be achieved using pultruded Carbodur plates reinforced polymer laminate, externally bonded to the
structure with epoxy adhesive Sikadur®‐30.
The material shall be a pultruded, unidirectional CFRP plate, and exhibit a fibre volume content >68%.
The plates shall be straight, flat and free of torsion.
The material shall have a long track record (> 25 years) for structural strengthening.
Test reports regarding reaction of adhesive joint to artificial weathering after 100 days shall be provided.
6.1.1. Concrete surface preparation
Any unsound material shall be removed and removed concrete shall be repaired as described above. Large blowholes and
honeycombing shall be filled with a suitable repair mortar.
Repair materials shall be fully compatible with the adhesive.
The actual strength of the concrete substrate shall be verified with at least three pull‐off tests.
The concrete shall be older than 28 days.
The laitance layer on the substrate surface shall be removed and an open‐textured surface shall be created.
The substrate surface shall be cleaned so that it is free from oil, grease and any other contaminants as well as loose particles
and dust.
The substrate moisture content shall be less than 4% pbw.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
12/15
6.1.2. Sika CarboDur® plates
The materials shall comply with the performance characteristics described as follows:
6.1.2.1. Typical Properties of Sika CarboDur® S plates:
Fibre volume content > 68%
Glass transition temp. > 100°C
E‐Modulus EN 2561/ASTM D3039 170000 N/mm² (MPa)
Tensile Strength EN 2561/ASTM D3039 3100 N/mm² (MPa)
Strain at break EN 2561/ASTM D3039 > 1.7%
6.1.3. Epoxy Adhesive
The material shall be epoxy based, and combine primer, putty and adhesive in one product.
The material shall not release substances dangerous to health, hygiene and the environment.
The material shall be long‐term creep resistant proven by independent report.
The material shall meet the requirements of EN 1504‐4 as structural bonding product for bonded plate reinforcement.
6.1.3.1. Typical Properties of Sikadur®‐30 adhesive:
The adhesive must comply with EN 1504‐4.
Density (parts A+B mixed) at +23°C 1.65 kg/l + 0.1 kg/l
50° 50 N/mm²
Slant shear strength at steel: 60° 60 N/mm²
70° 70 N/mm²
Bond/adhesion strength: 14 N/mm²
Shear strength: 12 N/mm²
Compressive strength: 30 N/mm²
Shrinkage / expansion: 0.1%
Workability: 85 min. at 23°C
Sensitivity to water Pass
Modulus of elasticity: 2000 N/mm²
Coefficient of thermal expansion: 100 x 10‐6
Glass transition temperature: 40°C
Durability Pass
Compliance with FIP requirement
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
13/15
Sag flow Non sag up to 3 ‐5 mm in vertical
Squeezability 4000 m2 at +15°C at 15 kg
Volume change 0.04%
Shear strength at 15°C >14 N/mm²
Shear strength at 35°C >26 N/mm²
E‐modulus in compression 9600 N/mm²
E‐modulus in tensile 11200 N/mm²
6.1.4. Application procedure
The plates shall be cut to length using either a rotary disc cutter or a hacksaw.
The plates shall be cleaned and degreased with Sika® Colma® Cleaner or an Isopropyl alcohol based cleaner.
The adhesive shall be applied to the plates in a way that it is approximately 1 mm thick on the sides and 2 mm thick in the
middle of the plate.
A very thin layer of the adhesive shall be applied to the prepared substrate surface to fill any small voids and irregularities.
The plate shall be placed on the prepared area and pressed onto the substrate, first gently by hand and second with a hard
rubber roller, until adhesive material is squeezed out on both sides of the plate. The excess material shall be removed.
In case of plate intersections, the surface of the underlying plate shall be cleaned from dirt and grease and an adhesive ramp
shall be applied on both sides of the underlying plate so the top plate is connected to the substrate on the entire area.
The freshly bonded system shall not be disturbed for at least 24 hours and any vibrations shall be kept at a minimum during
the curing period of the adhesive.
If necessary, the applied system shall be protected with a suitable coating (compatibility tests between the coating and the
laminate shall be available).
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
14/15
7. LEGAL DISCLAIMER
THIS SOFTWARE APPLICATION AND THE RESULTS DERIVED FROM ITS UTILIZATION ARE INTENDED ONLY FOR USE BY
PROFESSIONAL USERS WITH EXPERT KNOWLEDGE IN THE AREA OF THE INTENDED APPLICATION. USERS MUST
INDEPENDENTLY VERIFY THE RESULTS BEFORE ANY USE AND TAKE INTO ACCOUNT THE SITE AND APPLICATION
CONDITIONS, PRODUCT DATA SHEET AND PRODUCT LITERATURE, TECHNICAL STATE OF THE ART AS WELL AS LOCAL
APPLICABLE STANDARDS AND REGULATIONS.
With respect to the software application and results derived from its use, SIKA MAKES NO WARRANTIES OF ACCURACY,
RELIABILITY, COMPLETENESS, MERCHANTABILITY OR FITNESS FOR ANY PURPOSE. THE SOFTWARE APPLICATION IS
PROVIDED ON AN "AS‐IS" BASIS AND SIKA EXPRESSLY DISCLAIMS ANY WARRANTIES WITH RESPECT TO THE SOFTWARE
APPLICATION AND RESULTS DERIVED FROM ITS USE.
Sika shall not be liable for any consequential, punitive, incidental, exemplary, or special damages (including but not limited
to loss of business opportunity or loss of profit) arising out of the evaluation or use of the software application and results
derived from its use.
The information, and, in particular, the recommendations relating to the application and end‐use of Sika products, are given
in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied
under normal conditions in accordance with Sika's recommendations. In practice, the differences in materials, substrates
and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor
any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any
written recommendations, or from any other advice offered. The user of the product must test the product's suitability for
the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights
of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must
always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be
supplied on request.
Except as indicated otherwise, all information, text, graphic images, features, functions, and layout contained in this
software are the exclusive property of Sika and may not be copied or distributed, in whole or in part, without the Company's
express written consent.
By transmitting information to Sika, you grant to the Company the unrestricted irrevocable license to use, reproduce,
display, modify, distribute and perform such information. Personal identity information is used by Sika only to process a
request for information by you or for marketing our products and services.
© Copyright Sika Services AG 2016
8. ABOUT SIKA® CARBODUR® CALCULATION SOFTWARE
Engineered by:
Cype Software ‐ Eusebio Sempere, 5 ‐ 03003 Alicante (Spain)
www.cype.com
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
15/15
SIKA® CARBODUR® CALCULATION SOFTWARE
PROJECT: OJAČANJE AB PLOČE NA MESTU PRAVOUG. OTVORA U Y
PRAVCU
ELEMENT:
INDEX
1. DESIGN CRITERIA AND REGULATIONS................................................................................................................................ 3
2. CALCULATION ASSUMPTIONS............................................................................................................................................ 3
2.1. Geometry............................................................................................................................................................. 3
2.2. Concrete............................................................................................................................................................... 3
2.3. Reinforcing steel................................................................................................................................................... 4
2.4. Strength reduction factors.................................................................................................................................... 4
2.5. Load factors.......................................................................................................................................................... 4
2.6. Requirements for restriction of crack width.......................................................................................................... 4
3. FRP STRENGTH................................................................................................................................................................... 4
3.1. Main FRP reinforcement....................................................................................................................................... 4
4. ANTICIPATED COMBINATIONS OF LOADS.......................................................................................................................... 5
4.1. Initial loads........................................................................................................................................................... 5
4.2. Expected loads (strenghtening design)................................................................................................................. 5
5. RESULTS............................................................................................................................................................................. 5
5.1. Summary of results............................................................................................................................................... 5
5.2. Ultimate limit states............................................................................................................................................. 5
5.3. Serviceability limit states...................................................................................................................................... 9
5.4. FRP arrangement.................................................................................................................................................. 11
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
1/15
6. PRODUCT SPECIFICATION.................................................................................................................................................. 12
6.1. Bonded Sika CarboDur® plates.............................................................................................................................. 12
6.1.1. Concrete surface preparation......................................................................................................................... 12
6.1.2. Sika CarboDur® plates..................................................................................................................................... 13
6.1.3. Epoxy Adhesive............................................................................................................................................... 13
6.1.4. Application procedure..................................................................................................................................... 14
7. LEGAL DISCLAIMER............................................................................................................................................................ 15
8. ABOUT SIKA® CARBODUR® CALCULATION SOFTWARE....................................................................................................... 15
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
2/15
1. DESIGN CRITERIA AND REGULATIONS
Flexural strengthening of beam. The calculation comprises the evaluation of the most unfavorable section as defined by the
user, based on:
‐ Sia 260: 2013 Basics of planning structural design projects
‐ Sia 262: 2013 Concrete structures
‐ SIA 166: 2004 Externally bonded reinforcement
‐ Near surface mounted (NSM) calculations are based on:
‐ Concrete Society Technical Report No. 55 (TR 55): design guidance for strengthening concrete structures using fibre
composite materials, Third Edition 2012.
‐ The design of post‐tensioned CFRP plates is based on the Sika® CarboStress® system.
‐ Country: Serbia
2. CALCULATION ASSUMPTIONS
2.1. Geometry
Cross section = Slab
Height = 280 mm
280
2.2. Concrete
Compressive strength of concrete
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
3/15
Concrete strength (fck) = 20 MPa
Cylinder specimen = 20 MPa
Cube specimen = 25 MPa
2.3. Reinforcing steel
Reinforcement layers
Steel fsk Es Diameter C. to c. spacing
Bottom layer d1 mm
(MPa) (MPa) (mm) (mm)
1. 14 (B240) 240 200000 14.00 100
2.4. Strength reduction factors
Defined by (SIA)
Concrete
c = 1.50
t = 1.00
fc = 1.00
1
30 3
fc 1
fck
Steel
s = 1.15
2.5. Load factors
SIA combinations Permanent loads Imposed loads
Anticipated loads 1.35 1.50
FRP Reinforcement failure 1.00 0.30
Fire situation 1.00 0.30
SLS, frequent 1.00 0.50
SLS, quasi‐permanent 1.00 0.30
Category A: domestic, residential areas
1 = 0.5
2 = 0.3
2.6. Requirements for restriction of crack width
Requirements for restriction of crack width in accordance with SIA 262
Normal
3. FRP STRENGTH
3.1. Main FRP reinforcement
Simply bonded. Sika CarboDur® S
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
4/15
C. to c. spacing El tl Width
Sika® CarboDur® S212 lu
(mm) (MPa) (mm) (mm)
Layer: 1 50 165000.00 1.200 0.0176 20.00
4. ANTICIPATED COMBINATIONS OF LOADS
4.1. Initial loads
(Positive) Mi : 61.60 kN∙m/m
4.2. Expected loads (strenghtening design)
Permanent loads (Positive) MG : 64.95 kN∙m/m
Imposed loads (Positive) MQ : 52.88 kN∙m/m
5. RESULTS
5.1. Summary of results
ULS Anticipated loads
loading Md (kN∙m/m) MRd (kN∙m/m) MRd Md (Nd = NRd)
Strengthened section
Su = 1.35 ∙ SG + 1.50 ∙ SQ 167.00 202.30
202.30 kN∙m/m 167.00 kN∙m/m
ULS Reinforcement failure
loading Md (kN∙m/m) MRd (kN∙m/m) MRd Md (Nd = NRd)
Un‐strengthened section
Su = 1.00 ∙ SG + 0.30 ∙ SQ 80.81 93.92
93.92 kN∙m/m 80.81 kN∙m/m
Serviceability limit states
loading Service stresses
s 0.9∙fsk
Su = 1.00 ∙ SG + 0.50 ∙ SQ
230.55 MPa 216.00 MPa
Serviceability limit states
loading Service stresses
c 0.45∙fck
Su = 1.00 ∙ SG + 0.30 ∙ SQ
8.03 MPa 9.00 MPa
5.2. Ultimate limit states
When analysing a cross‐section to determine its ultimate moment of resistance, the following assumptions should be made:
The strain distribution in the concrete in compression and the strains in the reinforcement, whether in tension or
compression, are derived from the assumption that plane sections remain plane and that no longitudinal slip occurs
between or within the components of the section.
The stresses in the concrete in compression are derived from the stress–strain curve in Section 3.1.7 of EN 1992‐1‐1.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
5/15
n
fcd
c2 cu2 Number
(MPa)
13.3 0.0020 0.0030 2
The tensile strength of the concrete is ignored.
The stresses in the steel reinforcement are derived from the stress–strain curves in Section 3.2 of EN 1992‐1‐1.
The strains in the cross‐section should take into account the strains present in the existing structure at the time of
application of the FRP reinforcement.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
6/15
The stresses in the FRP reinforcement are derived from the assumption that the FRP has a linear elastic characteristic
until rupture.
Restriction for FRP strain (SIA 166:2004). FRP main reinforcement
ld l min L lu , ld,max
L
ld : 0.0072
ld,max : 0.0080
l : 0.9000
Force balance of section. Initial loads
Mi = 61.60 kN∙m/m
Force balance of section. Initial loads
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.46 ‰
min = ‐0.92 ‰
Maximum stress in concrete fc = 5.42 MPa
Distance from extreme compression fiber to neutral axis x = 93.01 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐170.75 ‐0.85
FRP Reinforcement failure. Minimum combination of loads to be resisted by the un‐strengthened member.
Su = 1.00 ∙ SG + 0.30 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
7/15
MRd Md 93.92 kN∙m/m 80.81 kN∙m/m
Nominal moment MRd : 93.92 kN∙m/m
εmax σmax
ε = 3.0 ‰
ε = 2.0 ‰
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 2.54 ‰
min = ‐21.08 ‰
Maximum stress in concrete fc = 16.67 MPa
Distance from extreme compression fiber to neutral axis x = 30.07 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐240.00 ‐19.90
Strengthened section and expected loads.
Su = 1.35 ∙ SG + 1.50 ∙ SQ
MRd Md 202.30 kN∙m/m 167.00 kN∙m/m
Nominal moment MRd : 202.30 kN∙m/m
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
8/15
εmax σmax
ε = 3.0 ‰
ε = 2.0 ‰
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 2.99 ‰
min = ‐7.39 ‰
Maximum stress in concrete fc = 13.33 MPa
Distance from extreme compression fiber to neutral axis x = 80.60 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐208.70 ‐6.87
FRP ‐141 ‐1069.48 ‐6.48
5.3. Serviceability limit states
For serviceability limit states, stress in steel reinforcement of concrete shall satisfy the SIA‐262 requirements, or not exceeds
0.9∙fyk
Force balance of section. SLS Frequent combination of loads
Su = 1.00 ∙ SG + 0.50 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
9/15
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.51 ‰
min = ‐1.24 ‰
Maximum stress in concrete fc = 8.92 MPa
Distance from extreme compression fiber to neutral axis x = 81.72 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐230.55 ‐1.15
FRP ‐141 ‐56.70 ‐0.34
Force balance of section. SLS Quasi‐permanent combination of loads
Su = 1.00 ∙ SG + 0.30 ∙ SQ
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
10/15
εmax σmax
x
ε = 0.0 ‰
εmin
Maximum and minimum strain max = 0.45 ‰
min = ‐1.12 ‰
Maximum stress in concrete fc = 8.03 MPa
Distance from extreme compression fiber to neutral axis x = 80.68 mm
Stress and strain of reinforcement
Ref. Y Coord. (mm) f (MPa) ε (‰)
No. 14 ‐126 ‐207.98 ‐1.04
FRP ‐141 ‐36.53 ‐0.22
5.4. FRP arrangement
The previous results correspond to the following FRP scheme:
FRP main reinforcement: Sika® CarboDur® S212. C. to c. spacing: 50 mm
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
11/15
280
6. PRODUCT SPECIFICATION
6.1. Bonded Sika CarboDur® plates
The strengthening shall be achieved using pultruded Carbodur plates reinforced polymer laminate, externally bonded to the
structure with epoxy adhesive Sikadur®‐30.
The material shall be a pultruded, unidirectional CFRP plate, and exhibit a fibre volume content >68%.
The plates shall be straight, flat and free of torsion.
The material shall have a long track record (> 25 years) for structural strengthening.
Test reports regarding reaction of adhesive joint to artificial weathering after 100 days shall be provided.
6.1.1. Concrete surface preparation
Any unsound material shall be removed and removed concrete shall be repaired as described above. Large blowholes and
honeycombing shall be filled with a suitable repair mortar.
Repair materials shall be fully compatible with the adhesive.
The actual strength of the concrete substrate shall be verified with at least three pull‐off tests.
The concrete shall be older than 28 days.
The laitance layer on the substrate surface shall be removed and an open‐textured surface shall be created.
The substrate surface shall be cleaned so that it is free from oil, grease and any other contaminants as well as loose particles
and dust.
The substrate moisture content shall be less than 4% pbw.
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
12/15
6.1.2. Sika CarboDur® plates
The materials shall comply with the performance characteristics described as follows:
6.1.2.1. Typical Properties of Sika CarboDur® S plates:
Fibre volume content > 68%
Glass transition temp. > 100°C
E‐Modulus EN 2561/ASTM D3039 170000 N/mm² (MPa)
Tensile Strength EN 2561/ASTM D3039 3100 N/mm² (MPa)
Strain at break EN 2561/ASTM D3039 > 1.7%
6.1.3. Epoxy Adhesive
The material shall be epoxy based, and combine primer, putty and adhesive in one product.
The material shall not release substances dangerous to health, hygiene and the environment.
The material shall be long‐term creep resistant proven by independent report.
The material shall meet the requirements of EN 1504‐4 as structural bonding product for bonded plate reinforcement.
6.1.3.1. Typical Properties of Sikadur®‐30 adhesive:
The adhesive must comply with EN 1504‐4.
Density (parts A+B mixed) at +23°C 1.65 kg/l + 0.1 kg/l
50° 50 N/mm²
Slant shear strength at steel: 60° 60 N/mm²
70° 70 N/mm²
Bond/adhesion strength: 14 N/mm²
Shear strength: 12 N/mm²
Compressive strength: 30 N/mm²
Shrinkage / expansion: 0.1%
Workability: 85 min. at 23°C
Sensitivity to water Pass
Modulus of elasticity: 2000 N/mm²
Coefficient of thermal expansion: 100 x 10‐6
Glass transition temperature: 40°C
Durability Pass
Compliance with FIP requirement
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
13/15
Sag flow Non sag up to 3 ‐5 mm in vertical
Squeezability 4000 m2 at +15°C at 15 kg
Volume change 0.04%
Shear strength at 15°C >14 N/mm²
Shear strength at 35°C >26 N/mm²
E‐modulus in compression 9600 N/mm²
E‐modulus in tensile 11200 N/mm²
6.1.4. Application procedure
The plates shall be cut to length using either a rotary disc cutter or a hacksaw.
The plates shall be cleaned and degreased with Sika® Colma® Cleaner or an Isopropyl alcohol based cleaner.
The adhesive shall be applied to the plates in a way that it is approximately 1 mm thick on the sides and 2 mm thick in the
middle of the plate.
A very thin layer of the adhesive shall be applied to the prepared substrate surface to fill any small voids and irregularities.
The plate shall be placed on the prepared area and pressed onto the substrate, first gently by hand and second with a hard
rubber roller, until adhesive material is squeezed out on both sides of the plate. The excess material shall be removed.
In case of plate intersections, the surface of the underlying plate shall be cleaned from dirt and grease and an adhesive ramp
shall be applied on both sides of the underlying plate so the top plate is connected to the substrate on the entire area.
The freshly bonded system shall not be disturbed for at least 24 hours and any vibrations shall be kept at a minimum during
the curing period of the adhesive.
If necessary, the applied system shall be protected with a suitable coating (compatibility tests between the coating and the
laminate shall be available).
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
14/15
7. LEGAL DISCLAIMER
THIS SOFTWARE APPLICATION AND THE RESULTS DERIVED FROM ITS UTILIZATION ARE INTENDED ONLY FOR USE BY
PROFESSIONAL USERS WITH EXPERT KNOWLEDGE IN THE AREA OF THE INTENDED APPLICATION. USERS MUST
INDEPENDENTLY VERIFY THE RESULTS BEFORE ANY USE AND TAKE INTO ACCOUNT THE SITE AND APPLICATION
CONDITIONS, PRODUCT DATA SHEET AND PRODUCT LITERATURE, TECHNICAL STATE OF THE ART AS WELL AS LOCAL
APPLICABLE STANDARDS AND REGULATIONS.
With respect to the software application and results derived from its use, SIKA MAKES NO WARRANTIES OF ACCURACY,
RELIABILITY, COMPLETENESS, MERCHANTABILITY OR FITNESS FOR ANY PURPOSE. THE SOFTWARE APPLICATION IS
PROVIDED ON AN "AS‐IS" BASIS AND SIKA EXPRESSLY DISCLAIMS ANY WARRANTIES WITH RESPECT TO THE SOFTWARE
APPLICATION AND RESULTS DERIVED FROM ITS USE.
Sika shall not be liable for any consequential, punitive, incidental, exemplary, or special damages (including but not limited
to loss of business opportunity or loss of profit) arising out of the evaluation or use of the software application and results
derived from its use.
The information, and, in particular, the recommendations relating to the application and end‐use of Sika products, are given
in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied
under normal conditions in accordance with Sika's recommendations. In practice, the differences in materials, substrates
and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor
any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any
written recommendations, or from any other advice offered. The user of the product must test the product's suitability for
the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights
of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must
always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be
supplied on request.
Except as indicated otherwise, all information, text, graphic images, features, functions, and layout contained in this
software are the exclusive property of Sika and may not be copied or distributed, in whole or in part, without the Company's
express written consent.
By transmitting information to Sika, you grant to the Company the unrestricted irrevocable license to use, reproduce,
display, modify, distribute and perform such information. Personal identity information is used by Sika only to process a
request for information by you or for marketing our products and services.
© Copyright Sika Services AG 2016
8. ABOUT SIKA® CARBODUR® CALCULATION SOFTWARE
Engineered by:
Cype Software ‐ Eusebio Sempere, 5 ‐ 03003 Alicante (Spain)
www.cype.com
Sika Services AG Element: Date: 15/09/2022
Corporate Tech. Dept. Editor: Project: OJAČANJE AB PLOČE NA M...
Tüffenwies 16 Remarks:
8048 Zürich (Switzerland)
www.sika.com
15/15
SIKA® CARBODUR® CALCULATION SOFTWARE
PROJECT: OJA ANJE AB PLO E NA MESTU OTVORA KOD LEPTIRASTIH
ZIDOVA
ELEMENT:
INDEX
2. CALCULATION ASSUMPTIONS............................................................................................................................................ 3
2.1. Geometry............................................................................................................................................................. 3
2.2. Concrete............................................................................................................................................................... 3
2.3. Reinforcing steel................................................................................................................................................... 4
2.4. Strength reduction factors.................................................................................................................................... 4
2.5. Load factors.......................................................................................................................................................... 4
2.6. Requirements for restriction of crack width.......................................................................................................... 4
3. FRP STRENGTH................................................................................................................................................................... 4
3.1. Main FRP reinforcement....................................................................................................................................... 4
5. RESULTS............................................................................................................................................................................. 5
5.1. Summary of results............................................................................................................................................... 5
5.2. Ultimate limit states............................................................................................................................................. 5
5.3. Serviceability limit states...................................................................................................................................... 9
5.4. FRP arrangement.................................................................................................................................................. 11
7. LEGAL DISCLAIMER............................................................................................................................................................ 15
Flexural strengthening of beam. The calculation comprises the evaluation of the most unfavorable section as defined by the
user, based on:
- Concrete Society Technical Report No. 55 (TR 55): design guidance for strengthening concrete structures using fibre
composite materials, Third Edition 2012.
- The design of post-tensioned CFRP plates is based on the Sika® CarboStress® system.
- Country: Serbia
2. CALCULATION ASSUMPTIONS
2.1. Geometry
Cross section = Slab
Height = 280 mm
280
2.2. Concrete
Compressive strength of concrete
Steel
γs = 1.15
3. FRP STRENGTH
5. RESULTS
fcd
εc2 εcu2 Number
(MPa)
13.3 0.0020 0.0030 2
The tensile strength of the concrete is ignored.
The stresses in the steel reinforcement are derived from the stress–strain curves in Section 3.2 of EN 1992-1-1.
The strains in the cross-section should take into account the strains present in the existing structure at the time of
application of the FRP reinforcement.
εld : 0.0072
εld,max : 0.0080
κl : 0.9000
εmax σmax
x
ε = 0.0 ‰
εmin
FRP Reinforcement failure. Minimum combination of loads to be resisted by the un-strengthened member.
Su = 1.00 · SG + 0.30 · SQ
εmax σmax
εε == 3.0
0.0 ‰
2.0 ‰
x
εmin
εmin
εmin
εmin
6. PRODUCT SPECIFICATION
The material shall be a pultruded, unidirectional CFRP plate, and exhibit a fibre volume content >68%.
The material shall have a long track record (> 25 years) for structural strengthening.
Test reports regarding reaction of adhesive joint to artificial weathering after 100 days shall be provided.
The actual strength of the concrete substrate shall be verified with at least three pull-off tests.
The laitance layer on the substrate surface shall be removed and an open-textured surface shall be created.
The substrate surface shall be cleaned so that it is free from oil, grease and any other contaminants as well as loose particles
and dust.
The material shall not release substances dangerous to health, hygiene and the environment.
The material shall meet the requirements of EN 1504-4 as structural bonding product for bonded plate reinforcement.
The plates shall be cleaned and degreased with Sika® Colma® Cleaner or an Isopropyl alcohol based cleaner.
The adhesive shall be applied to the plates in a way that it is approximately 1 mm thick on the sides and 2 mm thick in the
middle of the plate.
A very thin layer of the adhesive shall be applied to the prepared substrate surface to fill any small voids and irregularities.
The plate shall be placed on the prepared area and pressed onto the substrate, first gently by hand and second with a hard
rubber roller, until adhesive material is squeezed out on both sides of the plate. The excess material shall be removed.
In case of plate intersections, the surface of the underlying plate shall be cleaned from dirt and grease and an adhesive ramp
shall be applied on both sides of the underlying plate so the top plate is connected to the substrate on the entire area.
The freshly bonded system shall not be disturbed for at least 24 hours and any vibrations shall be kept at a minimum during
the curing period of the adhesive.
If necessary, the applied system shall be protected with a suitable coating (compatibility tests between the coating and the
laminate shall be available).
With respect to the software application and results derived from its use, SIKA MAKES NO WARRANTIES OF ACCURACY,
RELIABILITY, COMPLETENESS, MERCHANTABILITY OR FITNESS FOR ANY PURPOSE. THE SOFTWARE APPLICATION IS
PROVIDED ON AN "AS-IS" BASIS AND SIKA EXPRESSLY DISCLAIMS ANY WARRANTIES WITH RESPECT TO THE SOFTWARE
APPLICATION AND RESULTS DERIVED FROM ITS USE.
Sika shall not be liable for any consequential, punitive, incidental, exemplary, or special damages (including but not limited
to loss of business opportunity or loss of profit) arising out of the evaluation or use of the software application and results
derived from its use.
The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given
in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied
under normal conditions in accordance with Sika's recommendations. In practice, the differences in materials, substrates
and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor
any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any
written recommendations, or from any other advice offered. The user of the product must test the product's suitability for
the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights
of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must
always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be
supplied on request.
Except as indicated otherwise, all information, text, graphic images, features, functions, and layout contained in this
software are the exclusive property of Sika and may not be copied or distributed, in whole or in part, without the Company's
express written consent.
By transmitting information to Sika, you grant to the Company the unrestricted irrevocable license to use, reproduce,
display, modify, distribute and perform such information. Personal identity information is used by Sika only to process a
request for information by you or for marketing our products and services.
Engineered by:
157 50 545 50
1
POS 109
44 25 31
50
+5.17
100
D
50 385 50 46
90 15
40 40
+5.00
28 20
12x15.45/30
157 50 166 264 90 25 30
102
102
cm
POS 103, d=28
82
230
+4.15
54
459
486
412
412
388
388
9x15.45/30
336
30
640
POS 119 POS 108
253
60
60
B
C
50
50
12x15.45/30
cm
30
28
cm
d=
415
POS 104
POS 103
28
POS 101
445
435
385
385
385
385
00,
, d=
S1
253
1400
1400
1630
104
PO
S
PO
POS 107
30
B
50
50
60
60
A
POS 120
±0,00
253
173
198
55 1395 80 420 80 410 100 130 100 360 120 360 120 360 120 350 140 290 140 300 120 310 120 310 120 310 120 310 120 220 100 2 80 380 80 108 40 232 80 380 80 380 80 380 80 380 80 380 80 380 80 380 80 220 80 380 80 240 40 168 30 62 100 495 35 20 20
193
760
5260
40
40
30 30
30
579
POS 102, d
508
125
POS 106
608
= 28 cm
18
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 11' 10 9 8 7 6 30 420 305 230 30 230 304 230 30 230 330 230 302 375 30 1
115 30 3750 30 -1.25 5 60 5
265
320
295
236
85
125
13 13
40 40
POS 105
25 1535
-2.50
100
A
40
8 40
50
8
1
188 40
96 349 96
223 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 192 595
13000 15 772 - DOGRAĐEN DEO
B C
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1n 2n
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1n 2n
Otvori u ploči po originalnom projektu
Otvori u ploči naknadno napravljeni 157 50 545 50
1
Otvori u ploči naknadno napravljeni
44 25 31
50
100
D
90 15
40 40
Ø30
170
Ø40
Otvori u ploči po originalnom projektu
98
12x15.45/30 Otvori u ploči po originalnom projektu
Otvori u ploči po originalnom projektu 157 50 166 264 90 25 30
Ø50
80
100
230
130
110
110
110
110
110
110
110
459
Ø30
486
110
412
412
388
418
9x15.45/30
336
861 130 159 130 581 130 214 130 344 130 130 24 130 617 130 558 130 893 110 130 100 200 130 278 Ø1
875 5
179
30
146 130
234
375 155
184
179
179
112 22
214
37 7 10
5
1691 20 65
0
184
Ø1
Ø1
40 135 2033 70
3720 123
143 424220 95
85 33
33 57
67 2034
44 48
48 93 28 75
103 46 202327
43 5740 19 19 47 75 192119 166
40 191920 106
135 19 74 51 86446 191719 150 20 100 202120 140 20 40 20 116 152915 75 22 101 15 125 153715 148 153615 63 15 105 15 125 153715 87 35
52 110 19 136
136 19 71 191520 46 19 111 19202032192019 159 19 40 2010192019 2819 77 19 1075 19 114 252219 36 192319 125 19 48 18 19 81 20 71 19 84 20 54 33 81 193119 69 19 36 46 89 18 80 18 77 18 65 23 128 26 139 30 139 61 37 48 75 25 321 61
640
10
239
239
41 239
213
90 55
Ø15
57
52
58
40
57
120 160 60 133 96 116 140 52 163 51 78 120 140
47
41 44
51
53
44
49
48
48
31 41
42
47
0
46
40
Ø2 POS 108
30
30
22
Ø1
19
pr. 1 pr. 3 pr. 4 pr. 5 pr. 6
253
33 20 21 pr. 2
0
22
Ø2
600
310 356
60
60
B
C
50
I
0
12x15.45/30
2225
30
4450
435
385
385
385
253
1400
1400
1530
1630
223
POS 107
30
B
50
60
60
A
II
500 500 121 109 470 480 480 480 430 430 430 430 430 430 330 51 41 460 168 292 460 460 460 460 460 460 460 300 460 300 188
253
55 1395
760
30
579
508
533
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 11' 10 9 8 7 6 5 4 3 2 1 0
608
265
330
40 40
LEGENDA:
50
15
100
A
50
25
1
188 40 OTVOR U PLOČI
223 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 50 545 50
13000 192 595
POSTOJEĆI ARMIRANI BETON
CONSULTING
INVESTITOR:
NENAD DIMITRIJEVIĆ PR AGENCIJA ZA
PROJEKTOVANJE I TEHNIČKO SAVETOVANJE Fabrika kartona UMKA a.d.
ARČIBALDA RAJSA 13A, BEOGRAD Ulica 13. Oktobar br.1 , Umka, Beograd
STRUCTURAL
ODGOVORNI PROJEKTANT: OBJEKAT I MESTO GRADNJE:
Nenad Dimitrijević, dipl. inž. građ. HALA 6 - PROIZVODNI OBJEKAT KARTON MAŠINE
lic. br. 310 3018 03 Fabrika kartona UMKA a.d.
k.p.br.30633 K.O. Umka
PROJEKTANT: CRTEŽ: RAZMERA:
01
594
N. Dimitrijević PZI-PROJEKAT ZA IZVOĐENJE - KONSTRUKCIJA 02 mart 2023.
1800
DISPOZICIJA SKLOPA SUŠNE GRUPE NA KOTI +5.00:
44 25 31
50
100
90 15
40 40
523 458 491 452 491 452 491 452 491 452 276 452 276 452 276 452 443 220
12x15.45/30 52 52 63 63 55 56 63 63 55 56 63 63 55 56 63 63 55 56 63 63 55 56 63 63 55 56 63 63 55 56 63 63 +5.17 50 385 50 46
157 50 166 264 90 25 30
+5.00
230
28 20
459
486
412
412
388
418
9x15.45/30
336
102
102
82
+4.15
30
54
240
640
90 55
253
600
60
B
C
50
I
30
12x15.45/30
2225
30
4450
435
385
385
385
253
1400
1400
1530
1630
415
223
30
B
50
60
60
A
II
500 500 121 109 470 480 480 480 430 430 430 430 430 430 330 51 41 460 168 292 460 460 460 460 460 460 460 300 460 300 188
253
55 1395
760
±0,00
30
579
508
533
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 11' 10 9 8 7 6 5 4 3 2 1 0
608
265
125
330
-1.25 5 60 5
40 40
50
15
100
50
85
25
125
13 13
1
188 40
-2.50
8 40
223 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 50 545 50
8
13000 192 595
96 349 96
B C
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1n 2n
Otvori u ploči po originalnom projektu
Otvori u ploči naknadno napravljeni 157 50 545 50
1
Otvori u ploči naknadno napravljeni
44 25 31
82
50
100
D
90 15
40 40
Ø20 Ø20
15
75 Ø40 Ø25 Ø40 60 Ø40 Ø30
45
45
Ø40 Ø40
110 Ø40
12x15.45/30 40 373 220 238 220 272 220 u ploči po originalnom
Otvori 232 projektu 220 272 220 232 220 272 220 232 220 272 220 232 220po originalnom
Otvori u ploči 57 projektu
220 232 220 57 220 233 220 56 220 232 220 333 220
39 43 54 123 Otvori u ploči po originalnom projektu 157 50 166 264 90 25 30
230
40
104
104
104
459
116
486
412
412
388
418
9x15.45/30
336
30
240
265
265
265
213
640
243
182
90 55
pr. 1 pr. 3 pr. 4 pr. 5 pr. 6 POS 108
253
pr. 2
600
60
B
C
50
I
12x15.45/30
2225
30
4450
385
385
385
435
253
1400
1400
1530
1630
NAPOMENE:
223
POS 107
- Položaj AB postamenata-temelja uskladiti sa mašinskim projektom.
30
B
50
60
60
A
II
- Planovi oplate AB postamenata-temelja su dati na crtežu broj 03.
500 500 121 109 470 480 480 480 430 430 430 430 430 430 330 51 41 460 168 292 460 460 460 460 460 460 460 300 460 300 188
253
55 1395
760
LEGENDA:
30
579
508
533
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 11' 10 9 8 7 6 5 4 3 2 1 0
608
OTVOR U PLOČI
265
330
AB POSTAMENTI (TEMELJI)
40 40
50
15
100
A
50
25
NOVI ARMIRANI BETON C25/30 (MB30)
1
188 40
223 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 50 545 50
13000 192 595
POSTOJEĆI ARMIRANI BETON
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1n 2n
Sve kote proveriti na licu mesta!
CONSULTING
INVESTITOR:
NENAD DIMITRIJEVIĆ PR AGENCIJA ZA
PROJEKTOVANJE I TEHNIČKO SAVETOVANJE Fabrika kartona UMKA a.d.
ARČIBALDA RAJSA 13A, BEOGRAD Ulica 13. Oktobar br.1 , Umka, Beograd
STRUCTURAL
ODGOVORNI PROJEKTANT: OBJEKAT I MESTO GRADNJE:
Nenad Dimitrijević, dipl. inž. građ. HALA 6 - PROIZVODNI OBJEKAT KARTON MAŠINE
lic. br. 310 3018 03 Fabrika kartona UMKA a.d.
k.p.br.30633 K.O. Umka
PROJEKTANT: CRTEŽ: RAZMERA:
02
594
N. Dimitrijević PZI-PROJEKAT ZA IZVOĐENJE - KONSTRUKCIJA 02 mart 2023.
1800
Presek 1-1, R 1:50:
Temelj pogona 2-9 sušne grupe (16 kom.) Presek A-A:
1
A
215
90 125
239 112
5 80 6 40 80 5
11 90 11 20 49 21
Ovaj prostor cca 130x53x112 cm
ne popunjavati betonom
60
63
99
OLAKŠANJE TEMELJA
Ovaj prostor 127x49x112 cm 99 26
4
OSTAVITI ŠUPLJE
ne popunjavati betonom
190
190
B B
130
127
127
+5.17 50 385 50
92
+5.00
B 49 B
28 20
102
102
82
1
+4.15
54
A
Ovaj prostor 127x49x112 cm
Presek B-B: OLAKŠANJE TEMELJA
OSTAVITI ŠUPLJE
445 265 ne popunjavati betonom
11
27
112
58
90
27
11
20 49 21 99 26
215
226 87 200
2
2
226 11 65 11 5 190 5
OLAKŠANJE TEMELJA
24 39 24 32 136 32
OLAKŠANJE TEMELJA
OSTAVITI ŠUPLJE
NAPOMENE:
OSTAVITI ŠUPLJE - Položaj AB postamenata-temelja uskladiti sa mašinskim projektom.
- Planovi armature su dati na crtežu broj 05.
112
112
50
+5.00 B B
Sve kote proveriti na licu mesta!
CONSULTING
LEGENDA: NENAD DIMITRIJEVIĆ PR AGENCIJA ZA
INVESTITOR:
102
Nenad Dimitrijević, dipl. inž. građ. HALA 6 - PROIZVODNI OBJEKAT KARTON MAŠINE
lic. br. 310 3018 03 Fabrika kartona UMKA a.d.
1113 39 1311
297
N. Dimitrijević
630
DISPOZICIJA OJAČANJA ČELIKA NA KOTI +5.00: DETALJI POS Č1 - ČELIČNOG OJAČANJA (10 kom.), R 1:10
1
ankeri R-XPT Throughbolt, 2x6M16x220
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1n 2n
1-1
157 50 545 50 R=1:10
2
65 220 220 220 220 220 50 +5.00 45 55 55 45
44 25 31
50
100
D
90 15
280
280
157 50 166 264 90 25 30
2 2
459
POS Č1
486
412
412
388
POS Č1
POS Č1
POS Č1
418
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
POS Č1
336
50
75
85
150
100
640
270
90 55
150
130
1 2 150x100x12
1 2 150x100x12
60
60
100
B
C
50
I
55
45
2
223
35 75 75 35
2 ankeri R-XPT Throughbolt, 4M16x220
ankeri R-XPT
2 220x15x270
445
435
385
385
385
115 15 1200 Throughbolt, 4M16x220 220
1400
1400
1630
223
1
B
50
60
60
A
II
2-2
500 500 121 109 470 480 480 480 430 430 430 430 430 430 330 51 41 460 168 292 460 460 460 460 460 460 460 300 460 300 188 R=1:10
1395
760
2 220x15x270 1 2 150x100x12
6 rupa Ø18
579
35
508
533
45
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 11' 10 9 8 7 6 5 4 3 2 1 0
608
100
220
150
110
100
330
45
35
50 220 220 220 220 220 50
50
15
100
15 1200
A
50
25
1
500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 50 545 50
13000 192 595 Štapovi i limovi - specifikacija
POS Tip Materijal n Širina Debljina Dužina Jed.težina Težina po kom.Ukupna težina
[kom] [mm] [mm] [mm] [kg/m] [kg] [kg]
Ukupno 1348.09
Profili - rekapitulacija
Limovi - rekapitulacija
1
b=50 mm, t=1.2 mm, e=80 mm b=50 mm, t=1.2 mm, e=80 mm b=50 mm, t=1.2 mm, e=80 mm b=50 mm, t=1.2 mm, e=80 mm b=50 mm, t=1.2 mm, e=80 mm b=50 mm, t=1.2 mm, e=80 mm
Ukupno 156.82
44 25 31
50
100
D
90 15
1000
1000
1000
1000
1000
1000
1000
1100
1100
1100
Zbirna rekapitulacija
1000
2200
2600
2200
2200
2200
2200
2200
2200
1097
459
1890
2200
486
412
412
388
418
1000
Ukupno 1348.09
336
540
32 kom.
14 kom. 5 x 10 kom. 30 kom. 32 kom. 32 kom. 32 kom. 32 kom. 29 kom.
32 kom. 32 kom. Ukupno (+ za spojna sredstva 3%) 1388.53
32 kom.
640
48 kom.
90 55
Rekapitulacija zavrtnjeva po sklopovima
60
60
B
C
50
I
Sklop Tip zavrtnja Broj komada Dužina Broj navrtki Broj sig. navrtki Tip sig. navrtke
[mm]
223
POS Č1 Anker R-XPT Throughbolt, M16x220 352 220 352 0
445
435
385
385
385
1400
1400
1630
223
B
50
60
60
A
II
500 500 121 109 470 480 480 480 430 430 430 430 430 430 330 51 41 460 168 292 460 460 460 460 460 460 460 300 460 300 188
1395
760
NAPOMENE:
- Karbonske trake ugrađivati u svemu prema tehničkom listu
579
508
533
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 11' 10 9 8 7 6 5 4 3 2 1 0
608
proizvođača, od strane izvođača obučenih i preporučenih od strane
proizvođača.
330
- Karbonske trake se postavljaju sa donje strane ploče, na osnom
razmaku 80 mm, na površinu betona pripremljenu u svemu po
50
tehničkim zahtevim od proizvođača.
15
100
A
50
25
- Čelične tiplove ugraditi u svemu prema tehničkom listu
1
500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 50 545 50
proizvođača, od strane izvođača obučenih i preporučenih od strane
proizvođača.
13000 192 595
CONSULTING
INVESTITOR:
NENAD DIMITRIJEVIĆ PR AGENCIJA ZA
PROJEKTOVANJE I TEHNIČKO SAVETOVANJE Fabrika kartona UMKA a.d.
ARČIBALDA RAJSA 13A, BEOGRAD Ulica 13. Oktobar br.1 , Umka, Beograd
STRUCTURAL
ODGOVORNI PROJEKTANT: OBJEKAT I MESTO GRADNJE:
Nenad Dimitrijević, dipl. inž. građ. HALA 6 - PROIZVODNI OBJEKAT KARTON MAŠINE
lic. br. 310 3018 03 Fabrika kartona UMKA a.d.
k.p.br.30633 K.O. Umka
PROJEKTANT: CRTEŽ: RAZMERA:
04
594
N. Dimitrijević PZI-PROJEKAT ZA IZVOĐENJE - KONSTRUKCIJA 02 mart 2023.
1800
Temelj pogona 1. sušne grupe (1 kom.) Temelj pogona 2-9 sušne grupe (16 kom.)
Šipke - specifikacija
2-2
R=1:25 ozn. oblik i mere
[cm]
Ø lg
[m]
n
[kom]
lgn
[m]
Napomena
14
2 2Ø12 2 2Ø12
R=1:25
30
27
1 Ø8/20 180
2 12 1.87 64 119.68
I-1 Q-188
7
1 Ø8/20
I-1 Q-188
I-4 Q-188
I-4 Q-188
1 1
Šipke - rekapitulacija
I-5 Q-188
112
58
I-6 Q-188
I-2 Q-188
I-2 Q-188
24
I-4 Q-188
I-4 Q-188
Ø lgn Jedinična težina Težina
[mm] [m] [kg/m'] [kg]
1 Ø8/20 B500B
39
87
1 1
27
8 236.80 0.40 93.54
I-3 Q-188
I-3 Q-188
I-3 Q-188 12 119.68 0.89 106.28
Sve mere proveriti na licu mesta!
24
2 2Ø12 2 2Ø12 1 Ø8/20
Ukupno (B500B) 199.81
I-3 Q-188
I-2 Q-188 Savijanja šipki i upustvo za montažu (u skladu sa standardom SRPS EN 1992-1-1:2015)
I-1 Q-188 I-1 Q-188 Ukupno 199.81
A) prečnik trna kod šiki kojim se uvodi sila B) Konstruktivni prečnik trna
cv > cnom
Mreže - specifikacija D
32 136 32 18 53 19 99 26
ØS
Pozicija Oznaka mreže B L n Jedinična težina Ukupna težina Napomena D D ds D
ØS
[cm] [cm] [kg/m2] [kg] D D ØS
215 cv
200 Temelj pogona 1. sušne grupe (1 kom) cV
cv > cnom cV cv > cnom
I-1 Q-188 192 108 8 2.96 48.96
Minimalne vrednosti cv
1-1 I-2 Q-188 119 108 2 2.96 7.59 upravne na prečnik krivine Prečnik trna D u mm Prečnik šipke armature Ø u mm Prečnik trna D u mm
R=1:25 I-3 Q-188 79 108 2 2.96 5.04
> 100 mm i > 7Øs min D = 10Øs Ø ≤16 4Øs
> 50 mm i > 3Øs min D = 15Øs
Ø > 16 7Øs
90 125 > 50 mm i < 3Øs min D = 20Øs
Ukupno 61.58
1-1 Klasa Zaštitni sloj betona cnom (cm)
Beton
R=1:25 Temelj pogona 2-9 sušne grupe (16 kom) izloženosti iznad unutra ispod spolja
88 I-1 Q-188 84 104 32 2.96 82.75
POSTAMENT-TEMELJ MB 30 (C25/30) XC2 3.00 3.00
-1
±Q 2
I-2
2 2Ø12
63
x8 I-2 Q-188 82 57 32 2.96 44.51
57
I-3 Q-188 140 88 32 2.96 116.43
Armatura: B500B * Self Compacting Concrete / samozbijajući beton
99
I-4 Q-188 104 181 48 2.96 267.89
I-3 Q-188
I-1 Q-188 I-5 Q-188 104 88 32 2.96 86.49
1 10Ø8/20
1 10Ø8/20
I-2 Q-188
2 2Ø12
8 I-6 Q-188 144 181 16 2.96 123.64
190
-1 8
I-2 Q-188
±Q 2
112
CONSULTING
127
INVESTITOR:
2 2 NENAD DIMITRIJEVIĆ PR AGENCIJA ZA
2 2 88
I-3 Q-188 ±Q-
1
Mreže - rekapitulacija PROJEKTOVANJE I TEHNIČKO SAVETOVANJE Fabrika kartona UMKA a.d.
92
0
I-3 x14 ARČIBALDA RAJSA 13A, BEOGRAD Ulica 13. Oktobar br.1 , Umka, Beograd
88 Oznaka mreže B L n Jedinična težina Ukupna težina celih tabli Neto ugrađena težina
[cm] [cm] [kg/m2] [kg] [kg]
STRUCTURAL
ODGOVORNI PROJEKTANT: OBJEKAT I MESTO GRADNJE:
Q-188 215 605 34 2.96 1309.07 783.29 Nenad Dimitrijević, dipl. inž. građ. HALA 6 - PROIZVODNI OBJEKAT KARTON MAŠINE
32 136 32 lic. br. 310 3018 03 Fabrika kartona UMKA a.d.
Ukupno 1309.07 783.29 k.p.br.30633 K.O. Umka
PROJEKTANT: CRTEŽ: RAZMERA:
200 20 49 21 99 26
PLAN RMATURE POSTAMENATA R 1:25
215
CAD: FAZA: REVIZIJA: DATUM: BROJ CRTEŽA:
PZI-PROJEKAT ZA IZVOĐENJE - KONSTRUKCIJA 02 mart 2023. 05
297
N. Dimitrijević
840