Professional Documents
Culture Documents
(https://swayam.gov.in) sauravarora1999@outlook.com
(https://swayam.gov.in/nc_details/NPTEL)
Announcements (announcements) About the Course (preview) Ask a Question (forum) Progress (student/home) Mentor (student/mentor)
How does an NPTEL 1) The grid cutting method for Laminated Object Manufacturing (LOM) to remove unwanted material is applied on 1 point
online course work? ()
Inside of the exterior contour
Week 0 () Outside of the exterior and inside of the interior contour
Outside of the interior contour
Week 1: Introduction to None of the above
Additive Manufacturing ()
No, the answer is incorrect.
Score: 0
Week 2: Computer Aided
Accepted Answers:
Process Planning for
Outside of the exterior and inside of the interior contour
Additive Manufacturing ()
2) XY raster scanning is preferred for area filling toolpath strategy over X and Y raster scanning as it provides 1 point
Week 3: Computer Aided
Process Planning for Homogeneous Part Properties
Additive Manufacturing () It has a minimum number of lifts
Mod 3 Lec 1: Introduction to 3) An accurate outer profile of a part has to be fabricated without leaving behind any internal voids. For this purpose the hybrid toolpath strategy 1 point
Liquid AM (unit? should be ___________________ for the outer contour followed by ___________________ for the inner contour
unit=29&lesson=32)
Contour Parallel, Zigzag
Lecture Notes for Week 3
Raster, Spiral
(unit?unit=29&lesson=35)
Zigzag, Contour Parallel
Week 3: Feedback Form
Hilbert, Raster
(unit?unit=29&lesson=33)
No, the answer is incorrect.
Quiz: Assignment-03 Score: 0
(assessment?name=157) Accepted Answers:
Contour Parallel, Zigzag
Solution to selected numerical
probelms-Assignment-03
4) Galvanometer can provide very high scanning speed in Vat Photopolymerization because 1 point
(unit?unit=29&lesson=175)
The low inertia of mirrors
Week 4: Liquid Additive
Manufacturing () Use of magnetic lens for beam deflection
High-speed travel of the laser beam
Week 5: Liquid Additive All of the above
Manufacturing ()
No, the answer is incorrect.
Score: 0
Week 6: Sheet Additive Accepted Answers:
Manufacturing () The low inertia of mirrors
Week 7: Wire Additive 5) The bottom-feeding method of recoating in Vat Photopolymerization is preferred when the build direction is 1 point
Manufacturing ()
-Z Direction
Beam Correction
Increasing the scanning speed
Lower the mirror inertia
Cure the photopolymer resin
No, the answer is incorrect.
Score: 0
Accepted Answers:
Beam Correction
8) In the Digital Light Processing (DLP)-based Vat Photopolymerization, binder jetting, and material jetting process, the method used to scan the area 1 point
inside the slicing contour is performed by
Pixel
Grid Cutting
Mask
No need for scanning
9) Which of the following properties of the final printed part are influenced by toolpath strategy in Additive Manufacturing 1 point
Surface Roughness
Dimensional Accuracy
Part Strength
All the above
No, the answer is incorrect.
Score: 0
Accepted Answers:
All the above
10) Which of the following is not the requirement for an idle toolpath 1 point
Constant stepover
Constant machine feed rate
Maximum number of lift
Quick heat dissipation
11) A rectangular and a square contour of dimension 6 cm×2 cm and 4 cm ×4 cm, ,respectively, are fabricated using the LOM process from a square 1 point
sheet of dimension 10 cm×10 cm. Calculate the ratio (USquare/URectangle) of the area of the unwanted material (U).
0.66
3
5
0.95
16) The ‘support overhang angle’ in Ultimaker Cura is the angle of inclination of the triangle normal from 1 point
17) A cube (10×10×10 cm) and a cuboid (10×15×10 cm) having an infill density of 30% and 20% respectively, are fabricated using the FDM process. 1 point
Calculate the ratio of the volume (VSquare/VRectangle ) of infill material (V)
0.5
0.75
5
1
18) ‘Focal length’ for toolpath planning in PowerMill for DED based processes can be specified through 1 point
19) The size of the print bed can be specified in Inkscape through 1 point
Print bed size cannot be specified
Stroke and paint
Appropriately setting the page size
Biarc interpolation
20) The missing triangles in an STL file can be regenerated by the following command in ‘DeskArtes’ 1 point
Transform
Repair Shell
Rotate
Translate
No, the answer is incorrect.
Score: 0
Accepted Answers:
Repair Shell