Professional Documents
Culture Documents
Address*
Mfg. Serial No Year Built* Edition & Addendum to API 650* 12th Edition-Latest
Address
Tank Designatio
5. Products Stored:
DESIGN AND TESTING Purchaser to Review Design Prior to Ordering Material? Yes No
7. Max. Design. Temp ° Design Metal Temp.* ° Design Liquid Level* 8.4 m
Design Pressur 6.89 kPa xternal Pressure -3.44 kPa ximum Fill Rate 120 m /Hr3
aximum Emptying Rate 120 m3/Hr
Floatation Considerations?
Yes No Flot. Suppl. Spec:* Applied Supplemental Load Spec.
8. Seismic Design? Yes No Appendix E Alternate Seismic Criteria Seismic Use Group 1
MBE Site Class D Vertical Seismic Design?Yes No Vertical Ground Motion Accelerator AV:
Basis of Lateral Acceleration (Select one) Mapped Seismic Parameters?Ss S1 S0 ; Site-Specific Procedures: MCE
Yes
Freeboard Required for SUG I Design Roof Tie Rods @ Outer Ring No
9. Wind Velocity for non-U.S. sites, 50-yr. wind speed (3-sec. Gu 162 km/Hr
Top Wind Girder Styl Detail - 'I' Dimensions* e Top Wind Girder as Walkway? Yes No
Plate Widths (Shell course heights) and Thicknesses * Numbers below Indicate Course Number.
1. 2400 x 8 2. 2000 x 8 3. 2000 x 8 4. 2000 x 8 5.
6. 7. 8. 9. 10.
11. 12. 13. 14. 15.
11. Open-Top and Fixed Roofs: (See Sheet 6 for Floating Roofs) Open Top?* Yes No
For Non-Frangible Roofs: Seal Weld Roof Plates to Top Angle on the Inside? Yes No ; Weld Rafters to Roof Plates? Yes No
Roof-to-Shell DetaiDetai 'I' of Annex -F - Fig F-2 Radial Projection of Horizontal Component of Top Angle*
Inward Outward
12. Bottom: Thickness* 10 Style* Cone - Up Slope* 1 : 35 Weld Joint Type* Lap
Annular Ring? Yes No Annular Ring: Minimum Radial Wid 750 (min) Thickness* 10 mm
Responsibility for Setting Water Quality: Purchaser Manufacturer Supplemental Test Water Quality Spec.
Test Water Source & Disposal Tie-In Locat ydro-Test Appendix J Tank? Yes No
Other
15. Inspection b in Shop; in Field
Supplemental NDE Responsibilit upplemental NDE Spec.
(Purch., Mfg., Other)
Positive Material Identification?Yes No PMI Requirements:
Leak Test Mthd: Roo Shell* As per API 650 Shell Noz./Manhole Reinf. P
Bottom* As per API 650 oating Roof Components*
Specify Additional Tolerances, if any, and Circumferential and Vertical Measurement Locations:
- Allowable Plumbness: sure and Record at a Minimum of cations or Every m (ft) around the Tank, at
the Following Shell Heights: (select one box): 1
/3 H, 2/3 H and H Top of Each Shell Course Other:
- Allowable Roundness: easure Radius and Record at a Minimum of cations or Every m (ft)
around the Tank, at the Following Shell Heights (select one box):
Top of Tank, H 1
/3 H, 2/3 H and H Top of Each Shell Course Other:
**See Data Sheet Instructions for the Maximum Allowable Additional Radial Tolerance.
Approvals: Revisions: Title:
By: Ck'd: Date:
Drawing No.: Sheet of
API Std 650 Storage Tank
AMETANK Data Sheet PAGE 3 OF 7
16. Coatings:
Internal Coatings by Per Spec.* As Per Spec
(Not Req'd., Others, Tank Mfg.)
External Coating by: Per Spec.* As Per Spec
(Not Req'd., Others, Tank Mfg.)
Under-Bottom Coating by Per Spec.* As per Spec
(Not Req'd., Others, Tank Mfg.)
20. Tank Measurement System: Required? Yes No Remote Capability Required? Yes No
23. Remarks:*
1. Nozzle Elevation and Orientation to be confirmed after site visit on contract award
2. the T
Component Head Type* Bolt or Anchor Material* Nut Material* Thread Series* C.A.
Flange Bolting HEX A 193 Gr B7 A 194 Gr 2H UN ++
UN
++ Total C.A., on the nominal diameter.
Table 3 NOZZLE and MANHOLE SCHEDULE* (for Fixed Roof, Shell, and Bottom)
Full
Neck Pen.
Size, Sch or On Flange Proj. to FF or Remaks
NPS, or Wall Reinf. Plate Open. Flange Class or CL or from Gasket Thick.
Mark Service Dia. (in.) Thick. Dimensions (Y/N) Type Thick. Datum Lines and Dimen.
Shell Nozzles
N9 Sample
Foam 4" WNRF 150# VTC
Connecti
N10 on. 1" WNRF 150#
Recircula
N11 tion Line 3" WNRF 150#
Heating
N12 Coil 3" WNRF 150#
Heating
N13 Coil 3" WNRF 150#
Table 3 NOZZLE and MANHOLE SCHEDULE* (for Fixed Roof, Shell, and Bottom)
Full
Neck Pen.
Size, Sch or On Flange Proj. to FF or Remaks
NPS, or Wall Reinf. Plate Open. Flange Class or CL or from Gasket Thick.
Mark Service Dia. (in.) Thick. Dimensions (Y/N) Type Thick. Datum Lines and Dimen.
ROOF Nozzles
N17 BLANK
VENT 2" WNRF 150# GAS
ET
N18 Emerge
GAAS 4" WNRF 150# Note -5
ncy
N19 Vent 24" WNRF 150# W/ Emergency Vent
Clean
Out 24" As per API 650 W/ Cover+Davit
Approvals: Revisions: Title:
By: Ckd: Date:
Drawing No.: Sheet of
API Std 650 Storage Tank
AMETANK Data Sheet PAGE 6 OF 7
24. Platform, Stairway, and Railing: Galvanizing Req'd?*Yes No Stairway Style* Spiral Walk Surf. Type* Greating
(Straight or Helical)
Architectural/Structural Specification
29. Various Other Items: Welded Flush-Type: Shell Connection Cleanout Fitting Waive Application of Appendix P? Yes No
Miscellany # Miscellany #4
Miscellany # Miscellany #6
Notes: