Command : C (enter) Center pt. : Pick any point TABLE Radius of circle : 200 (enter) STEP 2 – CIRCLE B (stand) Command : C (enter) Center pt. : Center of A Radius of circle : 50 (enter) STEP 3 - CIRCLE C (top) Command : C (enter) Center pt. : Pick any point Radius of circle : 200 (enter) 3D SOLID STEP 4 - EXTRUDE (base) Command : EXT (enter) Select object to extrude : Pick Circle A (enter) Specify height of extrusion : 50 (enter) STEP 5- EXTRUDE and MOVE (stand) Command : EXT (enter) A Select object to extrude : Pick Circle B (enter) Specify height of extrusion : 520 (enter) Command : M (enter) B Select object. : Pick Circle B (enter) C Base pt. or displacement : 0,0,50 enter Second pt of displacement (enter) STEP 6 - EXTRUDE and 3D CENTER MOVE (TOP) Command : EXT (enter) TABLE Select object to extrude : Pick Circle C (enter) Specify height of extrusion : 30 (enter) Command : M (enter) Select object. : Pick Circle C (enter) A Base pt. or displacement : 0,0,570 enter Second pt of displacement B (enter) SOLID EDITING C STEP 7 – Fillet R=30 (BASE) Command : F (enter) 1st object : Pick base Enter radius: 25 (enter) STEP 8 – Fillet R=30 (BASE) Command : BLOCK (Use snap off) 2D MODEL STEP 1 - CIRCLE A (base) Command : C (enter) 3D LAMP 1 Center pt. : Pick any point Radius of circle : 150 (enter STEP 2 - CIRCLE B (stand) Command : C (enter) Center pt. : Center of A Radius of circle : 30 (enter ) STEP 3 - CIRCLE C (lamp) Command : C (enter) Center pt. : Center of A Radius of circle : 250 (enter ) 3D SOLID STEP 4 - EXTRUDE (base) Command : EXT (enter) Select object to extrude : Pick Circle A (enter) Specify height of extrusion : 50 (enter) STEP 5- EXTRUDE and MOVE (stand) Command : EXT (enter) C Select object to extrude : Pick Circle B A (enter) Specify height of extrusion : 200 (enter) B Command : M (enter) Select object. : Pick Circle B (enter) Base pt. or displacement : 0,0,50 enter Second pt of displacement (enter) STEP 6 - EXTRUDE and MOVE (LAMP) Command : EXT (enter)
3D LAMP 1 Select object to extrude : Pick
Circle C (enter) Specify height of extrusion : T (enter) Specify angle: 35 (enter) Specify height of extrusion : 250 (enter) Command : M (enter) A Select object. : Pick Circle C (enter) Base pt. or displacement : 0,0,250 enter B Second pt of displacement (enter) SOLID EDITING C STEP 7 – Fillet R=30 (BASE) Command : F (enter) 1st object : Pick base Enter radius: 30 (enter) Chain/ radius: enter STEP 8 Command : BLOCK (Use snap off) 2D MODEL STEP 1 - CIRCLE A (base) Command : C (enter) 3D LAMP 2 Center pt. : Pick any point Radius of circle : 150 (enter STEP 2 - CIRCLE B (stand) Command : C (enter) Center pt. : Center of A Radius of circle : 30 (enter ) STEP 3 - CIRCLE C (lamp) Command : C (enter) Center pt. : Center of A Radius of circle : 250 (enter ) 3D SOLID STEP 4 - EXTRUDE (base) Command : EXT (enter) Select object to extrude : Pick Circle A (enter) Specify height of extrusion : 50 (enter) STEP 5- EXTRUDE and MOVE (stand) Command : EXT (enter) C Select object to extrude : Pick Circle B A (enter) Specify height of extrusion : 1400 (enter) B Command : M (enter) Select object. : Pick Circle B (enter) Base pt. or displacement : 0,0,50 enter Second pt of displacement (enter) STEP 6 - EXTRUDE and MOVE (LAMP) Command : EXT (enter)
3D LAMP 2 Select object to extrude : Pick
Circle C (enter) Specify height of extrusion : T (enter) Specify angle: 35 (enter) Specify height of extrusion : 250 (enter) Command : M (enter) A Select object. : Pick Circle C (enter) Base pt. or displacement : 0,0,1450 enter B Second pt of displacement (enter) SOLID EDITING C STEP 7 – Fillet R=30 (BASE) Command : F (enter) 1st object : Pick base Enter radius: 30 (enter) Chain/ radius: enter STEP 8 Command : BLOCK (Use snap off)