Professional Documents
Culture Documents
CF-Sample Panjoori
CF-Sample Panjoori
NAME OF WORK:- Replacement of old Pumping Machienery of LWSSto group pf Vill.Lamian Chourian Nawan Shahar Gheta etc.Earnest Money:- 2025 /---
Distt.Kangra H.P. Time:- 3Month
SUB HEAD:- S/E of Centrifugal pumping machinery with allied accessories
S.NO. DESCRIPTION SPECIFICATIOS QUANTITY RATE UNIT AMOUNT
(To be specified by In Figures In Words
(the tenderer)
1. Supply of horizontal spindle,horizontal/radial split casing and suction (backpull out arrangement) single/ 2 Sets of 3375 Each 101250.00
double / multistage centrifugal pumps or combination of pumps in series /parallel of KSB / Mather & Platt/ 15 HP each
Jyoti /Kirloskar /BE /Maxflow /Beaconweir make conforming to BIS: 1520-1980 (latestwith upto date a) Pump:-
ammendments) read with BIS: 9137-1978 (latest edition) suitable for lifting water of under mentioned
charactristics with impellers of bronze/suitable alloy, priming funnels,casing ring & shaft sleeves of bron b) Motor
suitable alloy, shaft of sutable steel grade with cast iron casing coupled directly through a flexible coupling
on a common C.I. / Cast steel base plate (base plate to be from the principle manufacturer of pumping sec) Coupling
to slippering/squirrel cage screen protected drip proof electric induction motor of Kirlokar / NGEF /
Crompton / Siemen /Jyoti /BHEL /GEC /ABB conforming to BIS: 325-1978 read read with BIS: 900-1968d) Base plate
(latest with upto date ammendments) It should include the cost of bearings, nuts & bolts,painting etc. and
shall be suitable for operation as per data given below.
i) Location of site The Site is located at a distance of _10___ KMs from
_____ Railway station by road and ___ KM by head load
ii) The altitude of place in which Altitude of place is _450_ m above MSL
pumping set is intended to work
iii) Type of current AC three phase with frequency of 50cycles/second
iv) Rated Voltage 415V ± 10%
v) Type of water (Raw/Treated) _______
vi) Charactrstics of water a) Temperature __ °C e) Total solids __ mg/litre
b) Turbidity __ NTU f) Others ____
c) pH ____
d) Hardness __ Mg/Litre(as CaCO3)
vii) Depth of Tank/ P.well _10_ mts.
viii) L.W.L in Tank/sump well __mts.
ix) Centre line Level of Pump __ mts.
x) Suction head _4.5_ mts.
xi) Discharge Level of highest point __mts.
xii) Nos of pumps reqd. _2_ Nos. pumps
xiii) Capacity 3.52 lps for each pump
xiv) Static Head in meters 110.90__ mts.
xv) Total head in Mts. 148.37_mts
xvi) Length of R/Main __mts
xvii) Dia of R/Main 80_ mm
xviii) Pumping hours per day _8_ hours
xix) Limits of pump operation (-) 25% to (+) 10% of Total head at duty point
xx) HP of motor /Drive unit Required BHP of pump at (+) 10% & (-) 25% of total head or BHP
with following margins/multiplying factor at duty point, whichever is higher
a) Upto 2 HP = 1.5 d) 10 to 20 HP = 1.2
b) 2 to 5 HP = 1.4 e) 20 to100 HP = 1.15
c) 5 to 10 HP = 1.3 f) Above 100 HP=1.10
xxi) R.P.M.of Pump (2900/1450rpm) _2900__r.p.m.
xxii) Test Run 16 hours continueously for 7 days
xxiii) NPSH available _3.20__mts.
2 Supply of suitable oil immersed star delta /auto tranformer /stator rotor starter of standard make such as MEI/ __ Nos Each
Kilburn/Jyoti/L&T/S&S conforming to BIS:8544-1979 latest with up to date ammendments for squirrel cage/
slippering motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load
release & dashpot,time lag,under voltage release with initial oil filling .
Note:- Star delta starter upto 37.5 KW, Auto Transformer Stareter between 37.5 KW to 75 KW and Stator Rotor Starter with slippering motor.
3 Providing M S sheet 16 SWG steel fabricated floor mounted closed almirah type switch board __ No. Each
including angale iron post of suitable height and size ISA 65x65x6mm duly painted comprising and
capable of mounting the following accessaries with all internal electric connections.
Note:- The drawing of panel board shall be subject to approval of Engineer in charge.
a) Ammeter AC supply,100 mm circular/square dial Auto electric/AE/IMP/Havells make of suitable range for __ Nos. Each
above motor with selector switches conforming to BIS: 1248-1983 latest with up to date ammendments.
b) Voltmeter AC supply,100 mm circular/square dial Auto electric/AE/IMP/Havells make of suitable range for __ No. Each
above motor with selector switches conforming to BIS: 8044-1978 with up to date ammendments.
c) ICTP switches with HRC fuses Kilburn/L&T/Standard/Siemen's/Havell's make and having capacity 30% __ Nos. Each
extra of the operational rating of motor as per BIS: 4064-1978 with upto date ammendments immediatly
after the power meter of HPSEB.
d) Busbar chamber having 3 copper bars of suitable rating for full length of 3 live phases and one copper bar __ No. Each
of half rating of full length for neutral conforming to BIS: 8084-1976 and BIS;11353-1985 read with
BIS;5578-1985 all latest with upto date ammendments.
e) MCB/OCB of suitable capacity of Kilburn/L&T/MEI/Standard/GEC make on in comming __ No. Each
feeder for motors offered by the tenderer conforming to BIS: 2516-1985 latest with upto date
ammendments with neutral linked under voltage release.
f) Three phase indicating lamps complete with toggle switches for individual motors conforming to BIS: 3452 __ Sets Each
( part I & II) latest with up to date ammendments.
g) Earth leakage circuit breaker (ELCB) of Standard/ Havell's make as per BIS: 2516-1977 with upto date __ No. Each
ammendments and of suitaible range with which should have control box, operating handel and trip/reset
bush button, on/ off indicators, re-indicating off spring condition of the circuit breaker for over current
protection. The circuit should be equipped with magnetic thermal release with metallic tape CTs.It should
also be fitted with earth fault for tripping of breaker on occurance of earth fault on/off breaker load side.
h) Hour run meter of approved make of four digit capacity conforming to BIS: 722 (latest edition) __ Nos. Each
i) Change over Switch of reputed make & suitable capacity conforming to relevant BIS code __ No. Each
j) Single phase preventor of reputed make & suitable capacity conforming to relevant BIS code __ No. Each
4 (a) Providing C.I. / Cast steel double flanged sluice valve of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/ __ Nos. Each
Leader make of size___mm & class____ having one size higher to delivery size of pump and capable of
with standing nominal seat pressure of ____ kg/cm^2
NOTE:-The C.I. sluice valve shall conform to BIS:780-1984 for 50 to 300mm dia & BIS:2906-1984 for 350 to 1200mm dia ( latest
edition). However if seat pressure exceeds the limits prescribed in above mentioned BIS, then it shall be of cast steel conforming to
class ASA-150 for seat pressure upto 21 Kg/cm² or class ASA-300 for seat pressure 52 Kg/cm² as per BS 1414 (API 600) .
(b) Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make C.I/ Cast steel double flanged __ Nos. Each
swing check type reflux valve having bye pass arrangement and one size higher to delivery size of pump
( size___mm & class ____ ) and shall be suitable for withstanding nominal seat pressure of ____ kg/cm^2
(c) Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make C.I/ Cast steel double flanged __ Nos. Each
swing check type reflux valve having bye pass arrangement and of size equal to dia of Rising main
i.e ___ mm & of class_____ and shall be suitable for withstanding nominal seat pressure of ____ kg/cm^2
NOTE:- The C.I. reflux valve shall conform to BIS: 5312-1984- Part-I ( latest edition). However if the seat pressure exceeds the
limits prescribed in BIS 5312 then it shall be of cast steel conforming to class ASA-150 for seat pressure upto 21 Kg/cm² or
class ASA-300 for seat pressure 52 Kg/cm² as per BS 1868 (API 600) .
(d) Supply of Kirloskar/Jyoti/Standard/KilburnKartar make cast iron double flanged sluice valve or foot valve on
suction side of pump having size one step higher than the suction size of pump
NOTE:-TheC.I. sluice valve shall conform to BIS: 780-1984 & the foot valve shall conform to BIS 4838-1986 (latest edition) .
5 (a) Providing & laying PVC insulated armoured power copper cable of Siemens/Finolex/Grandlay/
Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable
size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment
/accessories such as thimbles,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or
trenches under floor .The type,size & make will be subject to approval of HPSEB authorities.In case
of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.
a) On supply side of 3½ core( From HPSEB Meter to Switch &Starter) = __mts of Size _____ mm². __ mts. Per Metre
b) On motor side 3 core ( From Switch & Starter to Motor) = __ mts. of Size _____ mm². __ mts. Per Metre
(b) Providing & laying double loop earthing with copper plate 600x600x3mm thick electrode complete with material __ Job L.S.
such as charcoal, common salt ,GI pipes,thimbles,nuts & bolts,digging of pits,GI wiring & copper strips of suitable
size conforming to BIS:3043-1978 (latest edition) for above motors & other electrical equipments.
NOTE:-The strip size shall be 20x3 upto 18.5 KW, 25x3 for 18.5 to 37 KW, 25x5 for 37 to 55 KW & 32x5 beyond 55 KW.
(c) Supply & errection of floor/wall mounted power factor shunt capacitor conforming to BIS 2834-1986 __ Nos. Each
latest with upto date ammendments of BHEL/GEC/Machneil/ Mager/Bajaj make to raise the prevailing
power factor at site to 0.95 for direct connection to induction motor individually,of required KVAR
according to HP of motor offered including cable of Siemens/Gloster/ICC make from busbar chamber
chamber to capacitor & also including ICTP switches Kilburn/L&T/Standard/Siemen's/Havell's of conforming to
4064-1978 or latest with HRC fuses (Range to be specified by the tenderer.)
6(a) Supply of 100mm dia circular/square dial pressure gaugeof suitable rangeof Fiebeg/Bourden/ Precision/PREGA __ Nos. Each
make with all accessories such as stop cock,copper tubing etc. conforming to BIS:3624-1987 latest
with up to date ammendments.
(b) Supply of 100mm dia circular/square dial vacuum gauge of suitable range of Fiebeg//Bourden/ Precision/PREGA __ Nos. Each
make with all accessories such as stop cock,copper tubing etc. conforming to BIS: 3624-1987 latest
with up to date ammendments.
7 Prov. & laying MSERW pipes conforming to BIS; 1978-82 of suitable size for suction,delivery and common
header considering site requirements & NPSH required / available.The pipe sizes for suction & delivery shall as
per the requirement of offered pump and common header shall be equal to dia of R/main including cost of tapers,
flanges (conforming to relevant table of BIS:6392-1971), bends, rubber gaskets,3mm thick nuts & bolts and
specials up to 5 mtrs.away from the outer wall of pump house as per layout drawing approved by Engineer-in-
Charg. Pipe & material shall be capable of withstanding field test pressure equal to 1.5 times the operating pressure
The complete arrangement shall comprise of ; a) Suction pipe _____mm dia __ mm thick ( to be mentioned by tenederer) __ mts. Per Metre
b) Delivery pipe _____mm dia __mm thick ( -----do--- ) __ mts. Per Metre
c) Common header _____mm dia __mm thick __ mts. Per Metre
8 Errection of all equipments from S.No. 1 to 4, & 6 i/c cost of tees,bends tapers & any other fittings __ Job L.S.
required as per site conditions & as per directions of Engineer-in-Charge
TOTAL AMOUNT Rs. 101250.00
Executive Engineer,
I&PH Division Nurpur.
SUB HEAD: - SUPPLY & ERRECTION OF CENTRIFUGAL PUMPING MACHINARY WITH ALLIED ACCESSORIES Stage -2nd. )
===== ======================================================================= ======== ========= =========================== =========
A) SITE CONDITIONS
=======================================================================
i) Location of Site Site is located at 80 KM from Pathankot by Road
& 200 Meters by head load
ii) The altitude of place in which 600 Mts above MSL
the motor is intended to work
in ordinary service if it exceeds
1000 mt.
B) OPERATING CONDITIONS
=======================================================================
iv) System of earthing if any to Double loop earthing as per BIS 3043-1987
to be adopted. latest with upto date ammendments
C) MOTOR
===== ===========
xi) Type of slip ring gear whether Continouslly rated for Squirrel cage/
continouly rated or for starting Slipring motor
purposes only & whether to be fitted
with brush lifting or short circuiting
arrangements or both if interlocks
are rquired.
xii) Breakway torque in terms of rated Breakway torque to be given by the tenderer
load torque & the corresponding but the starting current should not exceed
breakway starting current which 2.5 times of the full load current.
may be taken from the supply with
the starting apparatus in circuit.
xiii) Nature of load & any information To work the pump offered
regarding the driven machine which
has a bearing upon the torque reqd.
during the accelerated period, the
kinetic energy of the moving parts
to be accelrated & No.of starts
during a specified period.
xiv) Where possible fault capacity of The motor should be able to withstand
the system to which the motor is initial current of 2.5 times the rated
connected. current for two minutes without suffering
damages or permanent deformations.
D) PUMP (BIS 1520-1980 ) read with BIS 9137-1978 both latest with up to date ammendments
======================================================================= ========
c) Optional fittings reqd. Air cock for exahausting air from each
stage.
E) PUMP OPERATING CONDITIONS
============================
viii) Limits of total head in which (-) 25% to (+) 10% of total head.
the pump is reqd. to operate.
AMOUNT
============
131250.00
QUANTITY RATE UNIT AMOUNT
S.NO. DESCRIPTION
--------------- --------------------------------------- ---------------------------- -------------------------------------------------- --------------- --------------- --------------- --------------- ---------------
2 Supply of suitable oil immersed star delta starter of standarad
make such as MEI/Kilburn/Jyoti/ Siemen's conforming to
BIS-8544-1979 latest with up to date ammendments for squirrel
cage/slipriing motor (make to be specified by the tenderers) mounted on panel board with
magnetic type over load release & dashpot,time lag,under voltage release with initial 2 each
oil filling . Nos
Note:- Star - delta - starter upto 37.5 KW , ATS between 37.5 KW to 50 KW and stater rotor
starter with slipring motor beyond 50 KW.
3 Providing M S sheet 16 SWG steel fabricated floor mounted closed almirah type switch
board including angale iron post of suitable height and size ISA 40x40x6mm duly painted
comprising and capable of mounting the following accessaries with all internal 1 Each
electric connections. The drawing of panel board shall be subject to approval of No.
Engineer in charge.
c) ICTP switches with HRC fuses Kilburn/Larsen & turbo/Standard/Siemen make and having 2 Each
capacity 30% extra of the operational rating of motor as per BIS 4064-1978 with upto date Sets
ammendments immediatly after the power meter of HPSEB.
d) Busbar chamber having 3 copper bars of suitable rating for full length equal to wirdth 1 Each
of board of 3 live phases and one copper bar of half reating of full length for neutral No
conforming to BIS 8084-1976 and 11353-1985 read with 5578-1985 all latest with upto
date ammendments.
f) 3 phase indicating lamps complete with toggle switches for individual motors 2 Each
conforming to BIS 3452 part I & II latest with up to date ammendments. Sets
h) Hour run meter of reputed make of four digit capacity conforming to BIS-722(latest edition)/ 2 Each
recommendations. No.
I) Change over Switch of reputed make & suitable capacity Not Required Each
(d) Supply of Kirloskar/Jyoti/Standard/Kilburn make cast iron double flanged Sluice valve 2 Each
on suction side of pump of dia equal to suction pipe conforming to BIS 780-1984 No.
or latest with up to date ammendments.
5 (a) P/L suitable size copper PVC insulated armoured power 3 1/2 core cable conforming
to BIS 1554 (Part I) -1988 or latest with up to date ammendments Siemen/Gloster/ICC
make from meter of HPSEB to MCB & from MCB to Busbar switch & starter (one cable
carrying all three phases) including all other electrical equipment/accessories such
as thimbles,flexible pipe,solder,nuts & bolts,cable glands etc. laid in pipes or 1 LS
trenches under floor .The type,size & make will be subject to approval of HPSEB Job
authorities.In case of non acceptance by HPSEB authorities it shall have to be
replaced by the tenderer free of cost..
(b) P/L suitable size copper PVC insulated armoured power three core cable conforming
to BIS 1554(part I)-1988 or latest with up to date ammendments Siemen/Gloster/ICC
make from switch to starter & starter to motor (one cable for carrying all three phases)
including all other electrical equipment /accesories such as thimbles,flexible pipes, 1 LS
solder,nuts & bolts,cable glands etc. laid in pipes or trenches under floor. Job
The type,size & make will be subject to approval of HPSEB authorities.In case of non
acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.
(c) P/L double loop earthing with copper plate 600x600x3mm thick electrode complete with
material such as charcoal, common salt ,GI pipes,thimbles,nuts & bolts,digging of pits,GI wiring 1 LS
& 25x5mm copper strips of required capacity conforming to BIS 3043-1987 latest with up to date Job
ammendments for above motors & other electrical equipment.
(d) Supply & errection of floor/wall mounted power factor shunt capacitor conforming to BIS 2834-
1986 latest with upto date ammendments BHEL/GEC/Machneil/ Mager/Bajaj make to raise the
prevailing power factor at site to 0.95 for direct connection to induction motor 2 Each
individually,of required KVAR according to HP of motor offered including cable Siemens/ No.
Gloster/ICC make from busbar chamber to capacitor & also including LT/LK/Kilburn
make ICTP switches conforming to BIS 4064-1978 or latest with HRC fuses (Range to be
specified by the tenderer.
6(a) Supply of standarad make 100mm dia circular dial pressure gauge of suitable range Fiebeg/ 2 Each
Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming No.
to BIS 3624-1987 latest with up to date ammendments.
(b) Supply of standarad make 100mm dia circular dial vacuum gauge of suitable range Fiebeg/ Not Required Each
Bourden/Precision make with all accessories such as stop cock,copper tubing etc. conforming
to BIS 3624-1987 latest with up to date ammendments.
8 Supply of antivibration pads conforming to BIS 6337-1971 or latest with upto date 2 Each
ammendmentsof suitable size for above machinery. Sets
TOTAL 131250.00